Dahua Dahua Technology DH-IPC-HDBW1430DE-SW Dome IP Overvågningskamera (2560x1440) User manual [EN]

Download

Page 1

Network Camera Web 5.0

Operation Manual

ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.5

Page 2

General

This manual introduces the functions, configuration, general operation, and system maintenance of

network camera. Read carefully before using the platform, and keep the manual safe for future

reference.

Safety Instructions

The following signal words might appear in the manual.

Signal Words Meaning

Operation Manual

Foreword

Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.

Indicates a potential risk which, if not avoided, could result in property damage, data loss, reductions in performance, or unpredictable results.

Revision History

Version Revision Content Release Date

V1.0.5

V1.0.4

V1.0.3 Added parking space detection mode. November 2021

V1.0.2

Provides additional information as a supplement to the text.

Provides methods to help you solve a problem or save time.

Added the description of splicing and panoramic linkage.

Added the description of EPTZ, AI SSA and AFSA.

●

Added "6.2.2.2.14 Configuring Parking

Space".

●

Added "8.5 Setting Vehicle Density".

●

Added "8.6 Setting Parking Space".

●

Added "12.1.4 Crowd Distribution".

●

Added "12.1.5 Vehicle Density".

●

Updated "8.11 Setting ANPR".

September 2022

April 2022

July 2021

●

Added "8.8 Setting People Counting"

and "8.10 Setting Heat Map".

●

Added "6.2.1.11 Fisheye" and "7.4.4

V1.0.1

V1.0.0 First release. September 2020

Fisheye".

●

Updated "8.2 Setting Face

Recognition".

●

Updated "12 Report".

May 2021

Page 3

Privacy Protection Notice

As the device user or data controller, you might collect the personal data of others such as their face,

fingerprints, and license plate number. You need to be in compliance with your local privacy

protection laws and regulations to protect the legitimate rights and interests of other people by

implementing measures which include but are not limited: Providing clear and visible identification

to inform people of the existence of the surveillance area and provide required contact information.

About the Manual

●

The manual is for reference only. Slight differences might be found between the manual and the

product.

●

We are not liable for losses incurred due to operating the product in ways that are not in

compliance with the manual.

●

The manual will be updated according to the latest laws and regulations of related jurisdictions.

For detailed information, see the paper user’s manual, use our CD-ROM, scan the QR code or visit

our official website. The manual is for reference only. Slight differences might be found between

the electronic version and the paper version.

●

All designs and software are subject to change without prior written notice. Product updates

might result in some differences appearing between the actual product and the manual. Please

contact customer service for the latest program and supplementary documentation.

●

There might be errors in the print or deviations in the description of the functions, operations

and technical data. If there is any doubt or dispute, we reserve the right of final explanation.

●

Upgrade the reader software or try other mainstream reader software if the manual (in PDF

format) cannot be opened.

●

All trademarks, registered trademarks and company names in the manual are properties of their

respective owners.

●

Please visit our website, contact the supplier or customer service if any problems occur while

using the device.

●

If there is any uncertainty or controversy, we reserve the right of final explanation.

Operation Manual

Page 4

Important Safeguards and Warnings

This section introduces content covering the proper handling of the device, hazard prevention, and

prevention of property damage. Read carefully before using the device, and comply with the

guidelines when using it.

Transportation Requirements

●

Transport the device under allowed humidity and temperature conditions.

●

Pack the device with packaging provided by its manufacturer or packaging of the same quality

before transporting it.

●

Do not place heavy stress on the device, violently vibrate or immerse it in liquid during

transportation.

Storage Requirements

Operation Manual

●

Store the device under allowed humidity and temperature conditions.

●

Do not place the device in a humid, dusty, extremely hot or cold site that has strong

electromagnetic radiation or unstable illumination.

●

Do not place heavy stress on the device, violently vibrate or immerse it in liquid during storage.

Installation Requirements

●

Strictly comply with the local electrical safety code and standards, and check whether the power

supply is correct before operating the device.

●

Please follow the electrical requirements to power the device.

◇

When selecting the power adapter, the power supply must conform to the requirements of

ES1 in IEC 62368-1 standard and be no higher than PS2. Please note that the power supply

requirements are subject to the device label.

◇

We recommend using the power adapter provided with the device.

●

Do not connect the device to two or more kinds of power supplies, unless otherwise specified, to

avoid damage to the device.

●

The device must be installed in a location that only professionals can access, to avoid the risk of

non-professionals becoming injured from accessing the area while the device is working.

Professionals must have full knowledge of the safeguards and warnings of using the device.

●

Do not place heavy stress on the device, violently vibrate or immerse it in liquid during

installation.

●

An emergency disconnect device must be installed during installation and wiring at a readily

accessible location for emergency power cut-off.

●

We recommend you use the device with a lightning protection device for stronger protection

III

Page 5

against lightning. For outdoor scenarios, strictly comply with the lightning protection

regulations.

●

Ground the function earthing portion of the device to improve its reliability (certain models

are not equipped with earthing holes). The device is a class I electrical appliance. Make sure that

the power supply of the device is connected to a power socket with protective earthing.

●

The dome cover is an optical component. Do not directly touch or wipe the surface of the cover

during installation.

Operation Requirements

●

The cover must not be opened while the device is powered on.

●

Do not touch the heat dissipation component of the device to avoid the risk of getting burnt.

●

Use the device under allowed humidity and temperature conditions.

●

Do not aim the device at strong light sources (such as lamplight, and sunlight) when focusing it,

to avoid reducing the lifespan of the CMOS sensor, and causing overbrightness and flickering.

●

When using a laser beam device, avoid exposing the device surface to laser beam radiation.

●

Prevent liquid from flowing into the device to avoid damage to its internal components.

●

Protect indoor devices from rain and dampness to avoid electric shocks and fires breaking out.

●

Do not block the ventilation opening near the device to avoid heat accumulation.

●

Protect the line cord and wires from being walked on or squeezed particularly at plugs, power

sockets, and the point where they exit from the device.

●

Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the

lens.

●

The dome cover is an optical component. Do not directly touch or wipe the surface of the cover

when using it.

●

There might be a risk of electrostatic discharge on the dome cover. Power off the device when

installing the cover after the camera finishes adjustment. Do not directly touch the cover and

make sure the cover is not exposed to other equipment or human bodies

●

Strengthen the protection of the network, device data and personal information. All necessary

safety measures to ensure the network security of the device must be taken, such as using strong

passwords, regularly changing your password, updating firmware to the latest version, and

isolating computer networks. For the IPC firmware of some previous versions, the ONVIF

password will not be automatically synchronized after the main password of the system has been

changed. You need to update the firmware or change the password manually.

Operation Manual

Maintenance Requirements

●

Strictly follow the instructions to disassemble the device. Non-professionals dismantling the

device can result in it leaking water or producing poor quality images. For a device that is

required to be disassembled before use, make sure the seal ring is flat and in the seal groove

when putting the cover back on. When you find condensed water forming on the lens or the

desiccant becomes green after you disassembled the device, contact after-sales service to

replace the desiccant. Desiccants might not be provided depending on the actual model.

Page 6

Operation Manual

●

Use the accessories suggested by the manufacturer. Installation and maintenance must be

performed by qualified professionals.

●

Do not directly touch the photosensitive CMOS. Use an air blower to clean the dust or dirt on the

lens. When it is necessary to clean the device, slightly wet a soft cloth with alcohol, and gently

wipe away the dirt.

●

Clean the device body with a soft dry cloth. If there are any stubborn stains, clean them away

with a soft cloth dipped in a neutral detergent, and then wipe the surface dry. Do not use volatile

solvents such as ethyl alcohol, benzene, diluent, or abrasive detergents on the device to avoid

damaging the coating and degrading the performance of the device.

●

The dome cover is an optical component. When it is contaminated with dust, grease, or

fingerprints, use degreasing cotton moistened with a little ether or a clean soft cloth dipped in

water to gently wipe it clean. An air gun is useful for blowing dust away.

●

It is normal for a camera made of stainless steel to develop rust on its surface after being used in

a strong corrosive environment (such as the seaside, and chemical plants). Use an abrasive soft

cloth moistened with a little acid solution (vinegar is recommended) to gently wipe it away.

Afterwards, wipe it dry.

Page 7

Table of Contents

Operation Manual

Foreword

Important Safeguards and Warnings

1 Overview

1.1 Introduction

1.2 Network Connection

1.3 Functions

2 Configuration Flow

3 Device Initialization

4 Login

4.1 Device Login

4.2 Resetting Password

5 Home Page

6 Setting

6.1 Local

........................................................................................................................................................................................................I

................................................................................................................................................................................................... 1

................................................................................................................................................................................. 1

................................................................................................................................................................ 1

....................................................................................................................................................................................... 1

1.3.1 Basic Functions

1.3.2 AI Functions

............................................................................................................................................................................... 10

............................................................................................................................................................................................. 13

............................................................................................................................................................................................... 14

................................................................................................................................................................ 1

....................................................................................................................................................................... 2

.............................................................................................................................................................................. 5

............................................................................................................................................................................ 6

................................................................................................................................................................ 11

............................................................................................................................................ III

6.2 Camera

6.2.1 Setting Image Parameters

6.2.2 Setting Encode Parameters

.......................................................................................................................................................................................... 15

6.2.1.1 Page Layout

6.2.1.2 AI SSA

6.2.1.3 Image

6.2.1.4 Exposure

6.2.1.5 Backlight

6.2.1.6 WB

6.2.1.7 Day/Night

6.2.1.8 Illuminator

6.2.1.9 Defog

6.2.1.10 AFSA

6.2.1.11 Fisheye

6.2.2.1 Encode

6.2.2.2 Overlay

.............................................................................................................................................................................. 21

.......................................................................................................................................................... 15

....................................................................................................................................................................... 17

................................................................................................................................................................. 18

................................................................................................................................................................ 20

............................................................................................................................................................... 22

............................................................................................................................................................. 23

........................................................................................................................................................................ 24

....................................................................................................................................................................... 25

.................................................................................................................................................................. 26

..................................................................................................................................................................... 27

.................................................................................................................................................................... 29

........................................................................................................................................ 15

..................................................................................................................................... 26

6.2.2.2.1 Configuring Privacy Masking

6.2.2.2.2 Configuring Channel Title

6.2.2.2.3 Configuring Time Title

.................................................................................................................. 30

.......................................................................................................................... 31

............................................................................................................ 29

Page 8

Operation Manual

6.2.2.2.4 Configuring Location

6.2.2.2.5 Configuring Font Properties

6.2.2.2.6 Configuring Picture Overlay

6.2.2.2.7 Configuring Custom Title

6.2.2.2.8 Configuring Target Statistics

6.2.2.2.9 Configuring ANPR

................................................................................................................................... 34

6.2.2.2.10 Configuring Face Detection

6.2.2.2.11 Configuring Face Recognition

6.2.2.2.12 Configuring Face Statistics

6.2.2.2.13 Configure Face&Body Counting

6.2.2.2.14 Configuring Parking Space

6.2.2.3 ROI

6.2.3 Splicing

6.2.4 Audio

............................................................................................................................................................................. 38

.............................................................................................................................................................................. 39

................................................................................................................................................................................... 40

6.2.4.1 Setting Audio Parameters

6.2.4.2 Setting Alarm Tone

........................................................................................................................................... 41

............................................................................................................................ 31

............................................................................................................. 32

.............................................................................................................. 33

.................................................................................................................... 33

............................................................................................................ 34

............................................................................................................ 35

....................................................................................................... 36

.............................................................................................................. 36

................................................................................................... 37

............................................................................................................. 38

............................................................................................................................. 40

6.3 Network

6.3.1 TCP/IP

6.3.2 Port

6.3.3 PPPoE

6.3.4 DDNS

6.3.5 Email

6.3.6 UPnP

6.3.7 SNMP

6.3.8 Bonjour

........................................................................................................................................................................................ 42

.................................................................................................................................................................................. 42

....................................................................................................................................................................................... 45

.................................................................................................................................................................................. 47

................................................................................................................................................................................... 47

.................................................................................................................................................................................... 48

.................................................................................................................................................................................... 50

................................................................................................................................................................................... 51

.............................................................................................................................................................................. 54

6.3.9 Multicast

6.3.10 Register

6.3.11 QoS

.................................................................................................................................................................................... 56

6.3.12 Platform Access

6.3.12.1 P2P

6.3.12.2 ONVIF

6.3.12.3 RTMP

............................................................................................................................................................................ 54

........................................................................................................................................................................... 55

........................................................................................................................................................... 56

.......................................................................................................................................................................... 56

.................................................................................................................................................................... 57

...................................................................................................................................................................... 58

6.3.13 Basic Service

6.4 EPTZ

6.5 Event

................................................................................................................................................................................................ 60

.............................................................................................................................................................................................. 61

................................................................................................................................................................. 59

6.5.1 Setting Alarm Linkage

6.5.1.1 Setting Alarm-in

................................................................................................................................................ 61

................................................................................................................................................. 61

VII

Page 9

Operation Manual

6.5.1.2 Alarm Linkage

...................................................................................................................................................... 62

6.5.1.2.1 Adding Schedule

6.5.1.2.2 Record Linkage

......................................................................................................................................... 63

6.5.1.2.3 Snapshot Linkage

6.5.1.2.4 Alarm-out Linkage

6.5.1.2.5 Email Linkage

6.5.1.3 Subscribing Alarm

6.5.1.3.1 Alarm Types

............................................................................................................................................ 64

............................................................................................................................................. 65

............................................................................................................................................... 65

6.5.1.3.2 Subscribing Alarm Information

6.5.2 Setting Exception

......................................................................................................................................................... 66

6.5.2.1 Setting SD Card Exception

6.5.2.2 Setting Network Exception

6.5.2.3 Setting Voltage Detection

6.5.3 Setting Video Detection

............................................................................................................................................ 69

6.5.3.1 Setting Motion Detection

6.5.3.2 Setting Video Tampering

..................................................................................................................................... 62

................................................................................................................................... 64

.................................................................................................................................. 64

....................................................................................................... 65

............................................................................................................................ 67

........................................................................................................................... 67

............................................................................................................................. 68

.............................................................................................................................. 69

............................................................................................................................... 71

6.5.3.3 Setting Scene Changing

6.5.4 Setting Audio Detection

6.6 Storage

6.7 System

6.7.1 General

6.7.2 Account

.......................................................................................................................................................................................... 73

........................................................................................................................................................................................... 74

............................................................................................................................................................................... 74

6.7.1.1 Basic

6.7.1.2 Date & Time

.......................................................................................................................................................................... 74

........................................................................................................................................................... 75

.............................................................................................................................................................................. 76

6.7.2.1 User

........................................................................................................................................................................... 76

6.7.2.1.1 Adding User

6.7.2.1.2 Resetting Password

6.7.2.2 Adding User Group

6.7.2.3 ONVIF User

............................................................................................................................................................ 81

6.7.3 Peripheral Management

6.7.3.1 Configuring Serial Port

6.7.3.2 Configuring External Light

................................................................................................................................. 72

............................................................................................................................................ 72

............................................................................................................................................... 76

............................................................................................................................... 79

........................................................................................................................................... 80

........................................................................................................................................... 82

................................................................................................................................... 82

............................................................................................................................ 83

6.7.3.3 Configuring Wiper

6.7.4 Manager

............................................................................................................................................................................ 84

6.7.4.1 Requirements

6.7.4.2 Maintenance

6.7.4.3 Import/Export

............................................................................................................................................. 84

...................................................................................................................................................... 84

......................................................................................................................................................... 85

...................................................................................................................................................... 85

VIII

Page 10

Operation Manual

6.7.4.4 Default

6.7.5 Upgrade

6.8 System Information

6.8.1 Version

6.8.2 Online User

6.9 Setting Log

6.9.1 Log

........................................................................................................................................................................................ 87

6.9.2 Remote Log

7 Live

7.1 Live Page

...................................................................................................................................................................................... 90

7.2 Setting Encode

7.3 Live View Function Bar

7.4 Window Adjustment Bar

7.4.1 Adjustment

7.4.2 Zoom and Focus

7.4.3 Image Adjustment

..................................................................................................................................................................... 86

............................................................................................................................................................................. 86

................................................................................................................................................................ 87

............................................................................................................................................................................... 87

....................................................................................................................................................................... 87

.................................................................................................................................................................................. 87

...................................................................................................................................................................... 88

.......................................................................................................................................................................... 91

.......................................................................................................................................................... 92

...................................................................................................................................................... 93

...................................................................................................................................................................... 93

............................................................................................................................................................ 94

........................................................................................................................................................ 95

7.4.4 Fisheye

7.5 Display Mode

8 AI

8.1 Setting Crowd Distribution Map

8.1.1 Global Configuration

8.1.2 Rule Configuration

8.2 Setting Face Recognition

8.2.1 Enabling Face Recognition

8.2.2 Setting Face Database

8.2.2.1 Creating Face Database

8.2.2.2 Adding Face Picture

8.2.2.2.1 Single Adding

8.2.2.2.2 Batch Importing

8.2.2.3 Managing Face Picture

8.2.2.3.1 Editing Face Information

8.2.2.3.2 Deleting Face Picture

............................................................................................................................................................................... 96

.......................................................................................................................................................................... 100

................................................................................................................................... 103

............................................................................................................................................... 103

.................................................................................................................................................... 104

.................................................................................................................................................. 105

................................................................................................................................... 106

............................................................................................................................................. 109

............................................................................................................................... 109

....................................................................................................................................... 111

........................................................................................................................................ 111

.................................................................................................................................... 113

................................................................................................................................. 114

................................................................................................................. 114

......................................................................................................................... 115

8.2.2.4 Face Modeling

8.2.3 Setting Arm Alarm

.................................................................................................................................................. 116

..................................................................................................................................................... 116

8.2.4 Viewing Face Recognition Result

8.3 Setting Face Detection

8.4 Setting IVS

................................................................................................................................................................................ 122

....................................................................................................................................................... 120

....................................................................................................................... 119

Page 11

Operation Manual

8.4.1 Global Configuration

8.4.2 Rule Configuration

8.5 Setting Vehicle Density

8.6 Setting Parking Space

8.6.1 Rule Configuration

............................................................................................................................................... 123

.................................................................................................................................................... 124

..................................................................................................................................................... 128

........................................................................................................................................................ 130

.................................................................................................................................................... 130

8.6.1.1 For Parking Space Detection Fisheye WizMind Network Camera

8.6.1.2 For Other Cameras

8.6.2 Global Configuration

8.7 Setting Video Metadata

8.7.1 Global Configuration

8.7.2 Rule Configuration

8.7.3 Viewing Video Metadata Report

8.8 Setting People Counting

8.8.1 People Counting

8.8.2 Queuing

.......................................................................................................................................................................... 143

......................................................................................................................................................... 141

8.8.3 Global Configuration

......................................................................................................................................... 132

............................................................................................................................................... 136

.................................................................................................................................................... 136

............................................................................................................................................... 136

.................................................................................................................................................... 138

........................................................................................................................ 140

................................................................................................................................................... 140

............................................................................................................................................... 145

.......................................... 130

8.9 Face & Body Detection

8.9.1 Global Configuration

8.9.2 Rule Configuration

8.10 Setting Heat Map

8.11 Setting ANPR

........................................................................................................................................................................ 149

8.11.1 Lane Configuration

8.11.2 Rule Configuration

8.11.3 Picture

8.11.4 Allowlist

8.11.5 Blocklist

........................................................................................................................................................................... 152

....................................................................................................................................................................... 153

........................................................................................................................................................................ 156

....................................................................................................................................................... 146

............................................................................................................................................... 146

.................................................................................................................................................... 147

............................................................................................................................................................... 149

................................................................................................................................................ 150

................................................................................................................................................. 151

8.12 Setting Panoramic Linkage

8.12.1 Enabling Linkage Track

8.12.2 Configuring Calibration Parameter

9 Security

9.1 Security Status

9.2 System Service

................................................................................................................................................................................................. 160

....................................................................................................................................................................... 160

....................................................................................................................................................................... 161

........................................................................................................................................... 157

........................................................................................................................................ 157

............................................................................................................... 158

9.2.1 802.1x

9.2.2 HTTPS

.............................................................................................................................................................................. 161

............................................................................................................................................................................... 162

9.3 Attack Defense

9.3.1 Firewall

............................................................................................................................................................................ 163

9.3.2 Account Lockout

....................................................................................................................................................................... 163

........................................................................................................................................................ 164

Page 12

Operation Manual

9.3.3 Anti-DoS Attack

9.4 CA Certificate

.......................................................................................................................................................................... 165

.......................................................................................................................................................... 165

9.4.1 Installing Device Certificate

9.4.1.1 Creating Certificate

9.4.1.2 Applying for and Importing CA Certificate

9.4.1.3 Installing Existing Certificate

9.4.2 Installing Trusted CA Certificate

9.5 A/V Encryption

9.6 Security Warning

10 Record

................................................................................................................................................................................................. 171

10.1 Playback

....................................................................................................................................................................... 169

.................................................................................................................................................................. 170

................................................................................................................................................................................. 171

10.1.1 Playing Back Video

10.1.2 Clipping Video

.......................................................................................................................................................... 173

10.1.3 Downloading Video

10.2 Setting Record Control

10.3 Setting Record Plan

........................................................................................................................................................... 176

................................................................................................................................. 165

........................................................................................................................................ 165

........................................................................................ 166

.................................................................................................................... 167

........................................................................................................................ 168

................................................................................................................................................. 171

............................................................................................................................................... 174

.................................................................................................................................................... 175

10.4 Storage

10.4.1 Local Storage

.................................................................................................................................................................................... 177

............................................................................................................................................................. 178

10.4.2 Network Storage

....................................................................................................................................................................... 179

...................................................................................................................................................................... 181

................................................................................................................................................................................. 183

11 Picture

11.1 Playback

10.4.2.1 FTP

10.4.2.2 NAS

................................................................................................................................................................................................. 183

11.1.1 Playing Back Picture

11.1.2 Downloading Picture

11.2 Setting Snapshot Parameters

11.3 Setting Snapshot Plan

11.4 Storage

.................................................................................................................................................................................... 186

11.5 Setting Upload Method

12 Report

................................................................................................................................................................................................. 188

12.1 Viewing Report

.................................................................................................................................................................... 188

12.1.1 Face Recognition

..................................................................................................................................................... 179

.............................................................................................................................................. 183

............................................................................................................................................ 184

...................................................................................................................................... 185

..................................................................................................................................................... 186

.................................................................................................................................................. 186

..................................................................................................................................................... 188

12.1.2 Video Metadata

12.1.3 People Counting

........................................................................................................................................................ 189

...................................................................................................................................................... 190

12.1.4 Crowd Distribution

12.1.5 Vehicle Density

12.1.6 Heat Map

......................................................................................................................................................... 194

..................................................................................................................................................................... 195

................................................................................................................................................. 193

Page 13

Operation Manual

12.1.7 ANPR

12.2 Searching for Face Picture

12.3 Auto Upload

Appendix 1 Cybersecurity Recommendations

.............................................................................................................................................................................. 197

............................................................................................................................................. 198

.......................................................................................................................................................................... 199

..................................................................................................................... 204

XII

Page 14

1 Overview

1.1 Introduction

IP camera (Internet Protocol camera), is a type of digital video camera that receives control data and

sends image data through internet. They are commonly used for surveillance, requiring no local

recording device, but only a local area network.

IP camera is divided into single-channel camera and multi-channel camera according to the channel

quantity. For multi-channel camera, you can set the parameters for each channel.

1.2 Network Connection

In the general IPC network topology, IPC is connected to PC through network switch or router.

Figure 1-1 General IPC network

Operation Manual

Get IP address by searching on ConfigTool, and then you can start accessing IPC through network.

1.3 Functions

Functions might vary with different devices.

1.3.1 Basic Functions

Real-time Monitoring

●

Live view.

●

When live viewing the image, you can enable audio, voice talk and connect monitoring center for

quick processing on the abnormality.

●

Adjust the image to the proper position by PTZ.

●

Snapshot and triple snapshot abnormality of the monitoring image for subsequent view and

processing.

Page 15

●

Record abnormality of monitoring image for subsequent view and processing.

●

Configure coding parameters, and adjust live view image.

Alarm

●

Set alarm prompt mode and tone according to alarm type.

●

View alarm prompt message.

Exception

●

SD card error, network disconnection, illegal access, voltage detection and security exception.

●

When SD card error or illegal access is triggered, the system links alarm output and sending

email.

●

When network disconnection alarm is triggered, the system links recording and alarm output.

●

When the input voltage is more or less than the rated voltage, the alarm is triggered and the

system links sending email.

Video Detection

●

Motion detection, video tampering detection and scene changing detection.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, PTZ operation, and snapshot.

Operation Manual

Audio Detection

●

Audio input abnormal detection and intensity change detection.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, PTZ operation, and snapshot.

Record

●

Auto record as schedule.

●

Play back recorded video and picture as needed.

●

Download recorded video and picture.

●

Alarm linked recording.

Account

●

Add, edit and delete user group, and manage user authorities according to user group.

●

Add, edit and delete user, and configure user authorities.

●

Change user password.

1.3.2 AI Functions

IVS

●

Tripwire, intrusion, abandoned object, moving object, fast moving, parking detection, people

gathering, and loitering detection.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, and snapshot.

Page 16

Face Detection

●

Detects face and display the related attributes on the live page.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, PTZ operation, and snapshot.

Face Recognition

●

Displays the recognition result on the live view page

●

In general mode, makes comparison between the detected face with the faces in face database

after detecting face. You can set the alarm mode and reporting mode for each face database

separately, and set linkages for each reporting mode.

●

In counting mode, does precise face counting after detecting face.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, PTZ operation, and snapshot.

Crowd Distribution Map

●

View crowd distribution in real time for the timely arm to avoid accidents such as stampede.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, PTZ operation, and snapshot.

Operation Manual

Video Metadata

●

Captures people, non-motor vehicle and vehicle, and displays the related information on the live

page.

●

When an alarm is triggered, the system links alarm output.

People Counting

●

Counts the people flow in/out the detection area, and generates report.

●

When the number of counted number of people in the detection area or the stay duration

exceeds the configured value, an alarm will be triggered.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, PTZ operation, and snapshot.

Heat Map

●

Counts cumulative density of moving objects, and displays the result in different colors.

●

View report of heat map, which includes heat map and track map (track map is not available on

economic fisheye cameras).

ANPR

●

Recognizes plate number in detection area, and displays the related information on live page.

●

When an alarm is triggered, the system links alarm output and snapshot.

Face & Body Detection

●

Detects faces and human body separately, and then correlates the face and the body.

●

When select compliant mode, the camera can detect attributes including face masks, helmets,

glasses, safety vests, top color, and bottom color, and determine whether PPE requirements are

met. PPE compliance or non-compliance alarms can be triggered according to the alarm settings.

Page 17

●

When an alarm is triggered, the system links alarm output and snapshot.

Parking Space

●

Supports planned parking space and open parking space.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output,

sending email, and snapshot.

Vehicle Density

●

Includes road congestion and parking limit, and supports to view vehicle statistics through the

live page.

●

When the counted vehicle exceeds the configured vehicle number and the congestion time

exceeds the configured time, an alarm will be triggered.

●

When an alarm is triggered, the system performs linkages such as recording, alarm output and

sending email.

Operation Manual

Page 18

Operation Manual

2 Configuration Flow

For the device configuration flow, see Figure 2-1. For details, see Table 2-1. Configure the device

according to the actual situation.

Figure 2-1 Configuration flow

Table 2-1 Description of flow

Configuration Description Reference

Initialization

Camera parameters

Date & time

Basic parameters

IP address

Subscribe alarm

AI AI rules

Open IE browser and enter IP address to log in to the web page, The camera IP address is

192.168.1.108 by default.

Initialize the camera when you use it for the first time.

Configure image parameters, encoder parameters, and audio parameters to ensure the image quality.

Set date and time to ensure the recording time is correct.

Change IP address according to network planning for the first use or during network adjustment.

Subscribe alarm event. When the subscribed alarm is triggered, the system will record the alarm on the alarm tab.

Configure the necessary detection rules, such as face detection and IVS.

"4 Login"

"3 Device Initialization"

"6.2 Camera"

"6.7.1.2 Date & Time"

"6.3.1 TCP/IP"

"6.5.1.3 Subscribing Alarm"

"8 AI"

Page 19

Device initialization is required for the first-time use. This manual is based on the operation on the

web page. You can also initialize device through ConfigTool, NVR, or platform devices.

●

To ensure the device safety, keep the password properly after initialization and change the

●

When initializing device, keep the PC IP and device IP in the same network.

Procedure

Step 1 Open IE browser, enter the IP address of the device in the address bar, and then press the

Operation Manual

3 Device Initialization

password regularly.

Enter key.

The IP is 192.168.1.108 by default.

Figure 3-1 Region setting

Step 2 Select the area, language, and video standard according to the actual situation, and then

click

Page 20

Figure 3-2 Time zone setting

Operation Manual

Figure 3-3 Disclaimer

Step 3 Select the

I have read and agree to the terms of the Software License Agreement and

checkbox, and then click

Page 21

Figure 3-4 Time zone setting

Operation Manual

Step 4 Configure the time parameters, and then click

Figure 3-5 Password setting

Page 22

Operation Manual

Step 5 Set the password for admin account.

Table 3-1 Description of password configuration

Parameter Description

Username The default username is admin.

Password The password must consist of 8 to 32 non-blank characters and

contain at least two types of characters among upper case, lower

Confirm password

case, number, and special character (excluding ' " ; : &). Set a high security level password according to the password security notice.

Enter an email address for password resetting, and it is selected by default.

Reserved email

When you need to reset the password of the admin account, a security code for password resetting will be sent to the reserved email address.

Step 6 Click

, and then

page is displayed.

P2P

Page 23

4.1 Device Login

This section introduces how to log in to the web page. This section takes Chrome as an example.

●

You need to initialize the camera before logging in to the web page. For details, see "3 Device

Initialization".

●

When initializing the camera, keep the PC IP and device IP in the same network.

●

Follow the instruction to download and install the plug-in for the first login.

Procedure

Step 1 Open IE browser, enter the IP address of the camera (192.168.1.108 by default) in the

address bar and press Enter.

Step 2 Enter the username and password.

The username is admin by default.

Operation Manual

4 Login

Click

Forget password?

set during the initialization. For details, see "4.2 Resetting Password".

, and you can reset the password through the email address that is

Figure 4-1 Login

Step 3 Click

Page 24

4.2 Resetting Password

Operation Manual

Figure 4-2 Live page

When you need to reset the password for the admin account, there will be a security code sent to

the entered email address which can be used to reset the password.

Prerequisites

You have enabled password resetting service. For details, see "6.7.2.1.2 Resetting Password".

Procedure

Step 1 Open IE browser, enter the IP address of the device in the address bar and press Enter.

Figure 4-3 Login

Page 25

Operation Manual

Step 2 Click

set during the initialization.

Forget password?

, and you can reset the password through the email address that is

Figure 4-4 Login

Page 26

5 Home Page

Click at the upper-left corner of the page to display the home page.

Figure 5-1 Home page

Operation Manual

●

Live: View the real-time monitoring image.

●

AI: Configure AI functions of the camera.

●

Camera: Configure camera parameters, including image parameters, encoder parameters, and

audio parameters.

●

PTZ: Configure PTZ settings.

●

Event: Configure general events, including alarm linkage exception, video detection, and audio

detection.

●

System: Configure system parameters, including general, date & time, account, safety, default,

import/export, remote, auto maintain and upgrade.

●

Security: Check the device security status and set security functions.

●

Record: Play back or download recorded video.

●

Picture: Play back or download image files.

●

For the camera with multiple channels, through selecting channel numbers, you can set the

parameters of the channels.

●

Report: Search the AI event report and system report.

●

Alarm subscription: Subscribe alarm.

●

Skin setting: Set the skin.

●

Language setting: Set the language.

●

Restart: Click at the upper-right corner of the page, select

restarts.

●

Logout: Click at the upper-right corner of the page, select

●

Setting: Click at the upper-right corner of the page to set the basic parameters.

●

Full screen: Click at the upper-right corner of the page to enter full screen mode; click to

exit full screen mode.

Reboot

Logout

, and the camera

to go to the

Page 27

This section introduces the basic setting of the camera, including the configuration of Local, Camera,

Network, Event, Storage, System, System Information and Log.

For

Camera, Event

section takes method 1 as an example.

●

Method 1: Click , and then select the corresponding item.

●

Method 2: Click the corresponding icon on the home page.

6.1 Local

You can select protocol and configure the storage path for live snapshot, live record, playback

snapshot, playback download, and video clips.

Procedure

Step 1 Select >

and

Local

System

Operation Manual

6 Setting

, you can go to the configuration page through two methods. This

Figure 6-1 Local

Step 2 Click

playback download, and video clips.

Browse

to select the storage path for live snapshot, live record, playback snapshot,

Page 28

Table 6-1 Description of local parameter

Parameter Description

You can select the network transmission protocol as needed, and the options are

TCP, UDP

and

Multicast

Operation Manual

Protocol

Live Record

Playback Download

Video Clips

Live Snapshot

Playback Snapshot

Step 3 Click

Apply

Before selecting

parameters.

The recorded video of live page.

The default path is C:\Users\admin\WebDownload\LiveRecord.

The downloaded video of playback page.

The default path is C:\Users\admin\WebDownload\PlaybackRecor d.

The clipped video of playback page.

C:\Users\admin\WebDownload\VideoClips.

The snapshot of live page.

The default path is C:\Users\admin\WebDownload\LiveSnapshot.

The snapshot of playback page.

The default path is C:\Users\admin\WebDownload\PlaybackSnaps hot.

Multicast

, make sure that you have set the

Multicast

Admin in the path

refers to the account

being used.

6.2 Camera

This section introduces the camera setting, including image parameters, encoder parameters, and

audio parameters.

Camera parameters of different devices might vary.

6.2.1 Setting Image Parameters

Configure image parameters according to the actual situation, including image, exposure, backlight,

white balance, Day/Night, and light.

6.2.1.1 Page Layout

Configure camera parameters to improve the scene clarity, and ensure that surveillance goes

properly.

You can select normal mode, day mode, or night mode to view the configuration and the effect of

the selected mode, such as picture, exposure, and backlight.

Page 29

Operation Manual

Select the working mode as needed.

●

Self-adaptive: The camera will adjust the image according to the environment.

Figure 6-2 Page layout (self-adaptive)

●

Customized scene: You can select the profile as needed. Select the profile in

Time Plan Setting

and drag the slide block to set certain time as the selected profile. For example, set 8:00–18:00 as

day, and 0:00–8:00 and 18:00–24:00 as night

Figure 6-3 Page layout (customized scene)

●

Day/night switch: You can select

Day/Night

Day

night

Profile

and the surveillance system works under

Page 30

6.2.1.2 AI SSA

By enabling AI SSA (AI Scene Self-adaptation), the camera could detect environmental conditions,

such as rain, fog, backlight, low light and flicker, to adjust the parameters of the image to suit the

conditions, ensuring that clear images are always produced.

Operation Manual

Figure 6-4 Page layout (day/night switch)

Procedure

Step 1 Select >

Step 2 Select On in the dropdown list.

Step 3 Click

6.2.1.3 Image

You can configure picture parameters as needed.

Procedure

Step 1 Select >

Camera

After you enable

will be disabled by default.

AFSA

Apply

AI SSA

Camera

Image

, some other functions such as

Image

AI SSA

Image

Figure 6-5 Image

exposure, backlight, defog

and

Step 2 Configure picture parameters.

Page 31

Table 6-2 Description of picture parameters

Parameter Description

Select the picture style from soft, standard and vivid.

●

Soft: Default image style, displays the actual color of the image.

Style

Brightness

Contrast

Saturation

●

Standard: The hue of the image is weaker than the actual one, and

contrast is smaller.

●

Vivid: The image is more vivid than the actual one.

Changes the value to adjust the picture brightness. The higher the value is, the brighter the picture will be, and the smaller the darker. The picture might be hazy if the value is configured too big.

Changes the contrast of the picture. The higher the value is, the more the contrast will be between bright and dark areas, and the smaller the less. If the value is set too big, the dark area would be too dark and bright area easier to get overexposed. The picture might be hazy if the value is set too small.

Makes the color deeper or lighter. The higher the value is, the deeper the color will be, and the lower the lighter. Saturation value does not change image brightness.

Operation Manual

Sharpness

Gamma

Flip

Mirror

Step 3 Click

Apply

Changes the sharpness of picture edges. The higher the value is, the clearer the picture edges will be, and if the value is set too big, picture noises are more likely to appear.

Changes the picture brightness and improves the picture dynamic range in a non-linear way. The higher the value is, the brighter the picture will be, and the smaller the darker.

Changes the display direction of the picture, see the options below.

●

0°: Normal display.

●

90°: The picture rotates 90° clockwise.

●

180°: The picture rotates 90° counterclockwise.

●

270°: The picture flips upside down.

For some models, please set the resolution to be 1080p or lower

when using 90° and 180°. For details, see "6.2.2 Setting Encode

Parameters".

Click , and the picture will display with left and right side reversed.

6.2.1.4 Exposure

Configure iris and shutter to improve image clarity.

Cameras with true WDR do not support long exposure when WDR is enabled in

Procedure

Step 1 Select >

Camera

Image

Exposure

Backlight

Page 32

Figure 6-6 Exposure

Step 2 Configure exposure parameters.

Table 6-3 Description of exposure parameters

Parameter Description

You can select from 50 Hz, 60 Hz and Outdoor.

●

50 Hz: When the electric supply is 50 Hz, the system adjusts the

exposure according to ambient light automatically to ensure that

Anti-flicker

no stripe appears.

●

60 Hz: When the electric supply is 60 Hz, the system adjusts the

exposure according to ambient light automatically to ensure that

no stripe appears.

●

Outdoor: You can select any exposure mode as needed.

Operation Manual

Mode

Device exposure modes.

●

Auto: Adjusts the image brightness according to the actual

condition automatically.

●

Gain Priority: When the exposure range is normal, the system

prefers the configured gain range when auto adjusting according

to the ambient lighting condition. If the image brightness is not

enough and the gain has reached upper or lower limit, the system

adjusts shutter value automatically to ensure the image at ideal

brightness. You can configure gain range to adjust gain level when

using gain priority mode.

●

Shutter priority: When the exposure range is normal, the system

prefers the configured shutter range when auto adjusting

according to the ambient lighting condition. If the image

brightness is not enough and the shutter value has reached upper

or lower limit, the system adjusts gain value automatically to

ensure the image at ideal brightness.

●

Manual: Configure gain and shutter value manually to adjust image

brightness.

When the

priority, Shutter priority

Anti-flicker

is set to

Outdoor

Manual

, you can select

in the

Mode

Auto, Gain

list.

Page 33

Parameter Description

Operation Manual

Exposure Compensation

Shutter

Gain

Auto Iris

3D NR

Level

Step 3 Click

Apply

Sets the value, and it ranges from 0 to 50. The higher the value is, the brighter the image will be.

Set the effective exposure time. The smaller the value, the shorter the exposure time will be.

When selecting With minimum illumination, the camera increases Gain automatically to get clearer images.

This configuration is available only when the camera is equipped with auto-iris lens.

●

When auto iris is enabled, the iris size changes automatically

according to the ambient lighting condition, and the image

brightness changes accordingly.

●

When auto iris is disabled, the iris stays at full size and does not

change no matter how ambient lighting condition changes.

Works with multi-frame (no less than 2 frames) images and reduces noise by using the frame information between previous and latter frames.

This configuration is available only when the 3D NR is enabled.

The higher the level is, the better the result will be.

Gain Priority

Manual

, you can set Gain.

Mode

6.2.1.5 Backlight

You can select backlight mode from Auto, BLC, WDR, and HLC.

Procedure

Step 1 Select >

Step 2 Configure backlight parameters.

Camera

Image

Backlight

Figure 6-7 Backlight

Page 34

Table 6-4 Description of backlight parameters

Backlight mode Description

Operation Manual

BLC

WDR

HLC

Enable target when shooting against light. You can enable or disable

Customized

●

When you enable

exposure only to the set area according to ambient lighting condition

to ensure the image of the set area at ideal brightness.

●

When you disable

according to ambient lighting condition automatically to ensure the clarity of the darkest area.

The system dims bright areas and compensates dark areas to ensure the clarity of all the area. The higher the value is, the brighter the dark will be, but the more the noise will be.

, the camera can get clearer image of the dark areas on the

BLC

mode.

Customized

Default

mode, the system auto adjusts

mode, the system adjusts exposure

There might be a few seconds of video loss when the device is switching

to WDR mode from other mode.

Enable station or parking lot), the camera will dim strong light, and reduce the size of Halo zone to lower the brightness of the whole image, so that the camera can capture human face or car plate detail clearly. The higher the value is, the more obvious the HLC effect will be.

when extreme strong light is in the environment (such as toll

HLC

SSA

Step 3 Click

6.2.1.6 WB

WB function makes the image color display precisely as it is. When in WB mode, white objects would

always display white color in different environments.

Procedure

Step 1 Select >

Apply

Enable according to the environment to make the objects in the image clearer.

Camera

, the system automatically adjusts the image brightness

SSA

> WB.

Image

Figure 6-8 WB

Step 2 Configure WB parameters.

Page 35

Table 6-5 Description of WB parameters

WB Mode Description

Operation Manual

Auto

Natural

Street Lamp

Outdoor

Manual

Custom Area

Step 3 Click

6.2.1.7 Day/Night

Configure the display mode of the image. The system switches between color and black-and-white

mode according to the actual condition.

Apply

The system compensates WB according to color temperature to ensure color precision.

The system auto compensates WB to environments without artificial light to ensure color precision.

The system compensates WB to outdoor night scene to ensure color precision.

The system auto compensates WB to most outdoor environments with natural or artificial light to ensure color precision.

Configure red and blue gain manually; the system auto compensates WB according to color temperature.

The system compensates WB only to the set area according to color temperature to ensure color precision.

Procedure

Step 1 Select >

Step 2 Configure day and night parameters.

Camera

> WB.

Image

Figure 6-9 Day/night

Page 36

Table 6-6 Description of day and night parameters

Parameter Description

Operation Manual

Mode

Sensitivity

Delay

Step 3 Click

Apply

6.2.1.8 Illuminator

You can select device display mode from

Color, Auto

, and

B/W

Day/Night configuration is independent from profile management

configuration.

●

This configuration is available only when you set

You can configure camera sensitivity when switching between color and black-and-white mode.

This configuration is available only when you set

You can configure the delay when camera switching between color and black-and-white mode. The lower the value is, the faster the camera switches between color and black-and-white mode.

: The system displays color image.

Color

: The system switches between color and black-and-white

Auto

display according to the actual condition.

: The system displays black-and-white image.

B/W

Auto

Mode

This configuration is available only when the device is equipped with illuminator.

Procedure

Step 1 Select >

Step 2 Configure illuminator parameters.

Camera

Image

Figure 6-10 Light

Illuminator

Page 37

Table 6-7 Description of illuminator parameters

Parameter Description

Operation Manual

Fill Light

Mode

Set

Fill Light

●

IR Mode: Enable the IR illuminator, and the white light is disabled. When

an alarm is triggered, the system will link white light.

●

White Light: Enable the white light, and the IR illuminator is disabled.

When an alarm is triggered, the system will link white light.

●

Soft Light Mode: Enable IR illuminator and white light at the same time,

and adjust the brightness of the two illuminators to get clear images.

Manual

Auto

Zoom Priority

for sound and siren cameras.

Adjust the brightness of illuminator manually, and then the system will supply illuminator to the image accordingly.

The system adjusts the illuminator intensity according to the ambient lighting condition.

The system adjusts the illuminator intensity automatically according to the change of the ambient light.

●

When the ambient light turns darker, the system turns

on the low beam lights first, if the brightness is still

not enough, it turns on the high beam lights then.

●

When the ambient light turns brighter, the system

dims high beam lights until they are off, and then the

low beam lights.

●

When the focus reaches certain wide angle, the

system will not turn on high beam light in order to avoid over-exposure in short distance. In the meantime, you can configure light compensation manually to fine-tune IR light intensity.

Step 3 Click

6.2.1.9 Defog

The image quality is compromised in foggy or hazy environment, and defog can be used to improve

image clarity.

Procedure

Step 1 Select >

Apply

Off Illuminator is off.

Camera

Image

Defog

Page 38

Operation Manual

Figure 6-11 Light

Step 2 Configure defog parameters.

Table 6-8 Description of defog parameters

Defog Description

Configure function intensity and atmospheric light mode manually, and

Manual

Auto The system adjusts image clarity according to the actual condition.

then the system adjusts image clarity accordingly. Atmospheric light mode can be adjusted automatically or manually.

Off Defog function is disabled.

Step 3 Click

6.2.1.10 AFSA

You can enable AFSA (Anti-flicker Self-adaption) to prevent image flickering.

Procedure

Step 1 Select >

Apply

Camera

Image

Figure 6-12 AFSA

AFSA

Step 2 Select On or

When you select

disabled when there is no flicker.

Step 3 Click

Apply

in the dropdown list.

Auto

, AFSA function will be enabled when the camera detects flicker and

Auto

Page 39

6.2.1.11 Fisheye

Select installation mode and record mode according to the actual installation scene. When the

camera accesses the platform with corrective stream, the platform displays the corrective image.

This function is only available on fisheye device.

Procedure

Step 1 Select >

Camera

Image

Fisheye

Figure 6-13 Fisheye

Operation Manual

Step 2 Set installation mode and record mode.

Table 6-9 Description of fisheye parameters

Parameter Description

installation Mode You can select

●

1O: The original image before correction.

●

1P: 360°rectangular panoramic image.

●

2P: When the installation mode is

this mode. Two associated 180° rectangular image screens; at any

time, the two screens form a 360° panoramic image.

●

1R: Original image screen + independent sub-screen. You can

zoom or drag the image in all the screens.

Record Mode

Step 3 Click

Apply

●

2R: Original image screen + two independent sub-screens. You

can zoom or drag the image in all the screens.

●

4R: Original image screen + four independent sub-screens. You

can zoom or drag the image in all the screens.

●

1O + 3R: Original image screen + three independent sub-screens.

You can zoom or drag the image in original image screen, and move the image (upper and lower) in sub-screens to adjust the vertical view.

Ceiling, Wall

, or

Ground

Ceiling

Ground

, you can set

6.2.2 Setting Encode Parameters

This section introduces video parameters, such as video, snapshot, overlay, ROI (region of interest),

and path.

Page 40

Click

Default

configuration.

6.2.2.1 Encode

Configure video stream parameters, such as compression, resolution, frame rate, bit rate type, bit

rate, I frame interval, SVC, and watermark.

Procedure

Step 1 Select >

, and the device is restored to default configuration. Click

Camera

Encode

Figure 6-14 Encode

Refresh

Operation Manual

to view the latest

Step 2 Configure encode parameters.

Table 6-10 Description of encode parameters

Parameter Description

Click to enable sub stream, it is enabled by default.

Sub Stream

You can enable multiple sub streams simultaneously.

Page 41

Parameter Description

Select encode mode.

●

Compression

●

Click to enable smart codec to improve video compressibility and save storage space.

: Main profile encode mode. Compared with H.264B, it

H.264

requires smaller bandwidth.

H.264H

requires smaller bandwidth.

H.264B

bandwidth.

: Main profile encode mode. Compared with H.264, it

H.265

requires smaller bandwidth.

MJPEG

value to ensure clarity, you are recommended to set the value to the biggest value in the

Operation Manual

: High profile encode mode. Compared with H.264, it

: Baseline profile encode mode. It requires smaller

: When under this mode, the image requires high bit rate

Bit Rate

Reference Bit Rate

Smart Codec

Output Mode

Resolution

Frame Rate (FPS)

Bit Rate Type

Quality

After smart codec is enabled, the device would stop supporting the

third bit stream, ROI, and smart event detection.

You can select from

The resolution of the video. The higher the value is, the clearer the image will be, but the bigger the required bandwidth will be.

The number of frame in one second of video. The higher the value is, the clearer and smoother the video will be.

The bit rate control type during video data transmission. You can select bit rate type from:

●

(Constant Bit Rate): The bit rate changes a little and keeps

CBR

close to the defined bit rate value.

●

(Variable Bit Rate): The bit rate changes as monitoring

VBR

scene changes.

Single Stream

Flex Stream

The

Bit Rate Type

MJPEG

This parameter can be configured only when the as

VBR

The better the quality is, but the bigger the required bandwidth will be.

can only be set as

CBR

when

Encode Mode

Bit Rate Type

is set

Reference Bit Rate

Max Bit Rate

The most suitable bit rate value range recommended to user according to the defined resolution and frame rate.

This parameter can be configured only when the as

You can select the value of the

Reference Bit Rate

scene changes, but the max bit rate keeps close to the defined value.

VBR

Max Bit Rate

value. The bit rate then changes as monitoring

Bit Rate Type

according to the

is set

Page 42

Parameter Description

Operation Manual

Bit Rate

I Frame Interval

SVC

Watermark

Watermark String

Step 3 Click

6.2.2.2 Overlay

Apply

This parameter can be configured only when the as

Select bit rate value in the list according to actual condition.

The number of P frames between two I frames, and the

Interval

It is recommended to set

Scaled video coding, is able to encode a high quality video bit stream that contains one or more subset bit streams. When sending stream, to improve fluency, the system will quit some data of related lays according to the network status.

You can verify the watermark to check if the video has been tampered.

CBR

range changes as

●

1: The default value, which means that there is no layered

coding.

●

2, 3 and 4: The lay number that the video stream is packed.

changes.

FPS

I Frame Interval

twice as big as

Bit Rate Type

I Frame

FPS

is set

Configure overlay information, and it will be displayed on the

6.2.2.2.1 Configuring Privacy Masking

You can enable this function when you need to protect the privacy of some area on the video image.

You can select the type of the masking from

●

When selecting

You can drag 8 blocks at most, and the color is black.

●

When selecting

most.

●

Color Block

Mosaic

only, you can draw triangles and convex quadrilaterals as blocks.

, you can draw rectangles as blocks with mosaic. You can draw 4 blocks at

: You can draw 8 blocks at most.

Procedure

Step 1 Select >

Camera

Encode

Color Block

Overlay

Live

and

Mosaic

Privacy Masking

page.

Page 43

Figure 6-15 Privacy masking

Step 2 Configure privacy masking.

1) Click next to

2) Click

, and then drag the block to the area that you need to cover.

Add

Enable

3) Adjust the size of the rectangle to protect the privacy.

4) Click

Apply

Operation Manual

Related Operations

●

View and edit the block

Select the privacy masking rule to be edited in the list, then the rule is highlighted, and the block

frame is displayed in the image. You can edit the selected block as needed, including moving the

position, and adjusting the size.

●

Edit the block name

Double-click the name in

●

Delete the block

◇

Click to delete blocks one by one.

◇

Click

to delete all blocks.

Clear

Name

6.2.2.2.2 Configuring Channel Title

You can enable this function when you need to display channel title in the video image.

Procedure

Step 1 Select >

Camera

to edit the block name.

Encode

Overlay

Channel Title

Page 44

Figure 6-16 Channel title

Operation Manual

Step 2 Click next to

Click to add the channel title, and you can add 1 line at most.

Step 3 Move the title box to the position that you want in the image.

Step 4 Click

Apply

6.2.2.2.3 Configuring Time Title

You can enable this function when you need to display time in the video image.

Procedure

Step 1 Select >

Camera

Enable

, enter the channel title, and select the text alignment.

Encode

Overlay

Figure 6-17 Time title

Time Title

Step 2 Click next to

Step 3 Click next to

Step 4 Move the time box to the position that you want in the image.

Step 5 Click

Apply

6.2.2.2.4 Configuring Location

You can enable this function if you need to display text in the video image.

Enable

Week Display

to display the day of week.

Page 45

Text overlay and picture overlay cannot work at the same time, and the IPC that connects to mobile

NVR with private protocol would display GPS information as priority.

Procedure

Step 1 Select >

Camera

Encode

Overlay

Figure 6-18 Location

Location

Operation Manual

Step 2 Click next to

text is displayed in the video image.

Enable

Click to add the text overlay, and you can add 13 lines at most.

Step 3 Move the text box to the position that you want in the image.

Step 4 Click

Apply

6.2.2.2.5 Configuring Font Properties

You can enable this function if you need to adjust the font size in the video image.

Procedure

Step 1 Select >

Camera

Encode

Figure 6-19 Font properties

, enter the location information, and then select alignment. The

Overlay

Font Properties

Step 2 Select the font color and size.

You can set the RGB value to customize the font color.

Step 3 Click

Apply

Page 46

6.2.2.2.6 Configuring Picture Overlay

You can enable this function if you need to display picture information on the video image.

Text overlay and picture overlay cannot work at the same time.

Procedure

Step 1 Select >

Camera

Encode

Figure 6-20 Picture overlay

Overlay

Picture Overlay

Operation Manual

Step 2 Click next to

The picture is displayed on the video image.

Step 3 Move the overlaid picture to the position that you want in the image.

Step 4 Click

Apply

Enable

6.2.2.2.7 Configuring Custom Title

You can enable this function if you need to display custom information on the video image.

Procedure

Step 1 Select >

Camera

, click

Upload

Encode

Figure 6-21 Custom title

Overlay

, and then select the picture to be overlaid.

Custom Title

Step 2 Click next to

text alignment.

Enable

, enter the text that you want to display, and then select the

Page 47

Click to add the text overlay, and you can add 1 line at most.

Step 3 Move the custom box to the position that you want in the image.

Step 4 Click

Apply

6.2.2.2.8 Configuring Target Statistics

After configuring the target statistics, the number of target statistics will be displayed on the image.

Procedure

Step 1 Select >

Camera

Encode

Figure 6-22 Target statistics

Overlay

Target Statistics

Operation Manual

Step 2 Click next to

Click

Step 3 Move the custom box to the position that you want in the image.

Step 4 Click

The overlaid information will be displayed after enabling video metadata function.

to clear the statistics data.

Reset

Apply

6.2.2.2.9 Configuring ANPR

After enabling this function, ANPR statistics information will be displayed on the image. When the

overlay function is enabled during intelligent rules configuration, this function is enabled

simultaneously.

Procedure

Step 1 Select >

Camera

Enable

Encode

, select the statistics type, and then select the text alignment.

Overlay

ANPR

Page 48

Figure 6-23 ANPR

Operation Manual

Step 2 Select the

Enable

check box, select the statistics type, and then select text alignment.

Click

Step 3 Move the ANPR box to the position that you want in the image.

Step 4 Click

to clear the statistics data.

Reset

Apply

6.2.2.2.10 Configuring Face Detection

After enabling this function, face statistics information will be displayed on the image. When the

overlay function is enabled during intelligent rules configuration, this function is enabled

simultaneously.

Procedure

Step 1 Select >

Camera

Encode

Figure 6-24 Face detection

Overlay

Face Detection

Step 2 Click next to

Enable

, and select the text alignment.

Page 49

Operation Manual

Click

Step 3 Move the statistics box to the position that you want in the image.

Step 4 Click

The information will be displayed on the image after the face detection function is

enabled.

to clear the statistics data.

Reset

Apply

6.2.2.2.11 Configuring Face Recognition

After enabling this function, face statistics information will be displayed on the image. When the

overlay function is enabled during intelligent rules configuration, this function is enabled

simultaneously.

Procedure

Step 1 Select >

Camera

Encode

Figure 6-25 Face recognition

Overlay

Face Recognition

Step 2 Click next to

Enable

Click

Step 3 Move the statistics box to the position that you want in the image.

Step 4 Click

The information will be displayed on the image after the face recognition function is

enabled.

to clear the statistics data.

Reset

Apply

6.2.2.2.12 Configuring Face Statistics

After enabling this function, face statistics information will be displayed on the image. When the

overlay function is enabled during intelligent rules configuration, this function is enabled

simultaneously.

, select the statistics type, and then select the text alignment.

Procedure

Step 1 Select >

Camera

Encode

Overlay

Face Statistics

Page 50

Figure 6-26 Face statistics

Operation Manual

Step 2 Click next to

Enable

, and select the text alignment.

Click

Step 3 Move the statistics box to the position that you want in the image.

Step 4 Click

to clear the statistics data.

Reset

Apply

6.2.2.2.13 Configure Face&Body Counting

After enabling this function, face&body counting information will be displayed on the image. When

the overlay function is enabled during intelligent rules configuration, this function is enabled

simultaneously.

Procedure

Step 1 Select >

Camera

Encode

Figure 6-27 Face&body counting

Overlay

Face&Body Counting

Step 2 Select the

Enable

check box, and then select text alignment.

Page 51

Operation Manual

Click

Step 3 Move the face&body counting box to the position that you want in the image.

Step 4 Click

to clear the statistics data.

Reset

Apply

6.2.2.2.14 Configuring Parking Space

After enabling this function, parking space information will be displayed on the image. When the

overlay function is enabled during intelligent rules configuration, this function is enabled

simultaneously.

Procedure

Step 1 Select >

Camera

Encode

Figure 6-28 Parking space

Overlay

Parking Space

Step 2 Select the

Step 3 Select statistic type and text alignment.

Step 4 Click

6.2.2.3 ROI

Select ROI (region of interest) on the image and configure the image quality of ROI, and then the

selected image is display at defined quality.

Procedure

Step 1 Select >

Apply

Enable

Camera

check box.

Encode

ROI

Page 52

Figure 6-29 ROI

Operation Manual

Step 2 Click next to

quality of ROI.

●

Step 3 Click

Step 4 Click

6.2.3 Splicing

When the panorama contains multiple images captured by different lenses, enable this function.

Before splicing, make sure that the surveillance scene is large and there are no objects blocking the

camera from taking a clear picture, otherwise, the splicing might fail.

Procedure

Step 1 Select >

Enable

, draw an area on the image, and then configure the image

The higher the image quality value is, the better the quality will be.

Click

Apply

Add

to delete all the area boxes; select one box, and then click to delete it.

Clear

to add more ROI. You can draw 4 area boxes at most.

Camera

Splicing

Figure 6-30 Splicing

Step 2 Select the lenses that need to be spliced.

When splicing the image through selecting lenses, you need to select the continuous

splicing screens. The screen with the icon (deeper color) is the first screen of the

splicing. You can select any screen as the first one, and then select the following screens

continuously. The system supports the splicing of 2 lenses to 8 lenses.

●

This function is available on select models. And it is all sensors splicing by default.

●

For Multi-Sensor Panoramic + PTZ Camera, the 4-sensor device supports 2 to 4 lenses

Page 53

splicing; the 6-sensor device supports 2 to 6 lenses splicing; the 8-sensor device

supports 2-8 lenses splicing.

Step 3 Click

The system starts to splice the image.

●

Some cameras restart automatically after splicing is complete, you can view the results

●

Some cameras display splicing live window after splicing is complete. Click OK, and

of the splicing in the

then the default window appears. Click OK and the splicing will take effect.

Start

Live

6.2.4 Audio

You can configure audio parameters and alarm audio.

6.2.4.1 Setting Audio Parameters

This section introduces audio parameters, including encode mode, sampling frequency, audio in

type, and noise filter.

Operation Manual

window.

Procedure

Step 1 Select >

Camera

Audio

Figure 6-31 Audio

Step 2 Click next to

For the camera with multiple channels, select the channel number.

Enable

Please carefully activate the audio acquisition function according to the actual

requirements of the application scenario.

Step 3 Configure audio parameters.

Main Stream

Sub Stream

Page 54

Table 6-11 Description of audio parameters

Parameter Description

Operation Manual

Compression

Sampling Frequency

Audio Input Type

Noise Filter Enable this function, and the system auto filters ambient noise.

Microphone Volume Adjusts microphone volume.

Speaker Volume Adjusts speaker volume.

Step 4 Click

Apply

6.2.4.2 Setting Alarm Tone

You can record or upload alarm audio file. The audio file will be played when the alarm is triggered.

You can select audio

G.726, AAC, G.723

The configured audio encode mode applies to both audio and intercom. The default value is recommended.

Sampling number per second. The higher the sampling frequency is, the more the sample in a second will be, and the more accuracy the restored signal will be. You can select audio from

8000, 16000, 32000, 48000, 64000

You can select audio input type from:

●

: Requires external audio device.

LineIn

: Not require external audio device.

Mic

Encode Mode

from

PCM, G.711A, G.711Mu

Sampling Frequency

Procedure

Step 1 Select >

Camera

Audio Tone

Figure 6-32 Audio tone

Step 2 Click

Step 3 Configure the audio file.

●

Select

●

Select

Add

Record

Upload

, enter the audio name in the input box, and then click

, click

Browse

Record

to select the audio file to be uploaded, and then click

Page 55

Operation Manual

Upload

●

The camera supports recording audio file in .pcm format only. Recording is only

supported by select models.

●

You can upload audio files in .pcm, .wav2, .mp3, or .aac format.

Step 4 Select the file that you need.

Related Operations

●

Edit audio file

Click to edit the file name.

●

Delete audio file

Click to delete the file name.

●

Play audio file

Click to play the file name.

●

Download audio file

Click to download the file name.

Figure 6-33 Add alarm tone

6.3 Network

This section introduces network configuration.

6.3.1 TCP/IP

You can configure IP address and DNS (Domain Name System) server and so on according to

network planning.

Prerequisites

The camera has connected to the network.

Procedure

Step 1 Select >

Network

TCP/IP

Page 56

Figure 6-34 TCP/IP

Operation Manual

Step 2 Configure TCP/IP parameters.

Table 6-12 Description of TCP/IP parameters

Parameter Description

Host Name Enter the host name, and the maximum length is 15 characters.

Page 57

Parameter Description

Click to enable ARP/Ping to set IP address service. Get the camera MAC address, and then you can change and configure the device IP address with ARP/ping command.

This is enabled by default. During restart, you will have no more than 2 minutes to configure the device IP address by a ping packet with certain length, the server will be turned off in 2 minutes, or it will be turned off immediately after the IP address is successfully configured. If this is not enabled, the IP address cannot be configured with ping packet.

A demonstration of configuring IP address with ARP/Ping.

1. Keep the camera that needs to be configured and the PC within

the same local network, and then get a usable IP address.

2. Get the MAC address of the camera from device label.

3. Open command editor on the PC and enter the following

command.

Operation Manual

ARP/Ping

NIC

4. Restart the camera.

5. Check the PC command line, if information such as

192.168.0.125…

you can turn it off then.

6. Enter http://(IP address) in the browser address bar to log in.

Select the Ethernet card that need to be configured, and the default one is

Wire

is displayed, the configuration succeeds, and

Reply from

The mode that the camera gets IP:

●

Mode

●

MAC Address Displays host MAC address.

IP Version Select

: Configure

Static

Gateway

configured IP address is displayed.

DHCP

and the camera acquires IP address automatically.

IPv4

manually, and then click

: When there is DHCP server in the network, select

IPv6

IP Address, Subnet Mask

, and

Default

, the login page with the

Save

DHCP

Page 58

Parameter Description

Operation Manual

IP Address

Subnet Mask

Default Gateway

Preferred DNS IP address of the preferred DNS.

Alternate DNS IP address of the alternate DNS.

Step 3 Click

6.3.2 Port

Configure the port numbers and the maximum number of users (includes web, platform client, and

mobile phone client) that can connect to the device simultaneously.

Procedure

Step 1 Select >

Apply

Network

When you select mask that you need.

Static

, enter the IP address and subnet

Mode

●

IPv6 does not have subnet mask.

●

The default gateway must be in the same network segment with

the IP address.

TCP/IP

Figure 6-35 Port

Step 2 Configure port parameters.

●

0–1024, 1900, 3800, 5000, 5050, 9999, 37776, 37780–37880, 39999, 42323 are occupied

for specific uses.

●

Do not use the same value of any other port during port configuration.

Page 59

Operation Manual

Table 6-13 Description of port parameters

Parameter Description

The max number of users (web client, platform client or mobile

Max Connection

TCP Port Transmission control protocol port. The value is 37777 by default.

UDP Port User datagram protocol port. The value is 37778 by default.

HTTP Port Hyper text transfer protocol port. The value is 80 by default.

phone client) that can connect to the device simultaneously. The value is 10 by default.

●

Real time streaming protocol port, and the value is 554 by

default. If you play live view with QuickTime, VLC or Blackberry

smart phone, the following URL format is available.

●

When the URL format requiring RTSP, you need to specify

channel number and bit stream type in the URL, and also

username and password if needed.

●

When playing live view with Blackberry smart phone, you need to

turn off the audio, and then set the codec mode to H.264B and

resolution to CIF.

RTSP Port

RTMP Port

URL format example:

rtsp://username:password@ip:port/cam/realmonitor?channel=1&sub type=0

Among that:

●

Username: The username, such as admin.

●

Password: The password, such as admin.

●

IP: The device IP, such as 192.168.1.112.

●

Port: Leave it if the value is 554 by default.

●

Channel: The channel number, which starts from 1. For example,

if you are using channel 2, then the channel=2.

●

Subtype: The bit stream type; 0 means main stream (Subtype=0)

and 1 means sub stream (Subtype=1).

Example: If you require the sub stream of channel 2 from a certain device, then the URL should be:

rtsp://admin:admin@10.12.4.84:554/cam/realmonitor?channel=2&su btype=1

If username and password are not needed, then the URL can be:

rtsp://ip:port/cam/realmonitor?channel=1&subtype=0

Real Time Messaging Protocol. The port that RTMP provides service. It is 1935 by default.

HTTPS Port HTTPS communication port. It is 443 by default.

Step 3 Click

Apply

The configuration of

after reboot.

Max Connection

takes effect immediately, and others will take effect

Page 60

6.3.3 PPPoE

Point-to-Point Protocol over Ethernet, is one of the protocols that device uses to connect to the

internet. Get the PPPoE username and password from the internet service provider, and then set up

network connection through PPPoE, the camera will acquire a WAN dynamic IP address.

Prerequisites

●

The camera has connected to the network.

●

You have gotten the account and password from Internet Service Provider.

Procedure

Step 1 Select >

Network

PPPoE

Figure 6-36 PPPoE

Operation Manual

Step 2 Click , and then enter username and password.

Step 3 Click

6.3.4 DDNS

Properly configure DDNS, and then the domain name on the DNS server matches your IP address

and the matching relation refreshes in real time. You can always visit the camera with the same

domain name no matter how the IP address changes.

Prerequisites

Check the type of DNS server supported by the camera.

Procedure

Step 1 Select >

●

Disable UPnP while using PPPoE to avoid possible influence.

●

After making PPPoE connection, the device IP address cannot be modified through

web page.

Apply

The success prompt box is displayed, and then the real-time WAN IP address is displayed.

You can access camera through the IP address.

Network

DDNS

●

Third party server might collect your device information after DDNS is enabled.

●

Page 61

the connected devices in your account.

Figure 6-37 DDNS

Step 2 Click to enable the function.

Step 3 Configure DDNS parameters.

Operation Manual

Result

Table 6-14 Description of DDNS parameters

Parameter Description

Type The name and web address of the DDNS service provider, see the

matching relationship below:

●

CN99 DDNS web address: www.3322.org

Server Address

Domain Name The domain name you registered on the DDNS website.

Test

Username Enter the username and password that you got from the DDNS server

Password

Interval

Step 4 Click

Open the browser on PC, then enter domain name at the address bar and press

page is displayed.

Apply

●

NO-IP DDNS web address: dynupdate.no-ip.com

●

Dyndns DDNS web address: members.dyndns.org

Only when selecting whether the domain name registration is successful.

provider. You need to register an account (includes username and password) on the DDNS server provider's website.

The update cycle of the connection between the device and the server, and the time is 10 minutes by default.

NO-IP DDNS

type, you can click

Enter

to check

Test

, the login

6.3.5 Email

Configure email parameter and enable email linkage. The system sends email to the defined address

when the corresponding alarm is triggered.

Procedure

Page 62

Operation Manual

Step 1 Select >

Network

Figure 6-38 Email

Step 2 Click to enable the function.

Step 3 Configure email parameters.

Table 6-15 Description of email parameters

Parameter Description

SMTP Server SMTP server address

Port

Username The account of SMTP server.

Password The password of SMTP server.

Anonymous

Sender Sender’s email address.

Encryption Type

Subject

The port number of the SMTP server.

Click , and the sender's information is not displayed in the email.

Select from

None, SSL

For details, see Table 6-16.

Enter maximum 63 characters in Chinese, English, and Arabic numerals. Click to select title type, including

, and

Event Type

, and you can set maximum 2 titles.

and

TLS

For details, see Table 6-16.

Device Name, Device

Attachment Select the check box to support attachment in the email.

Page 63

Parameter Description

●

Receiver’s email address. Supports 3 addresses at most.

●

Receiver

Health Mail

Table 6-16 Description of major mailbox configuration

Mailbox SMTP server Authentication Port Description

After entering the receiver's email address, the

display. Click received successfully.

The system sends test mail to check if the connection is successfully configured. Click and configure the the system sends test mail as the set interval.

to test whether the emails can be sent and

Test

Sending Interval

Operation Manual

button is

Test

, and then

Gmail

Step 4 Click

6.3.6 UPnP

UPnP (Universal Plug and Play) is a protocol that establishes mapping relation between local area

and wide area networks. This function enables you to access local area device through wide area IP

address.

Prerequisites

●

Make sure the UPnP service is installed in the system.

●

Enable UPnP in the router.

●

Connect your device to the LAN port of the router.

●

Select >

select

Procedure

Step 1 Select >

smtp.gmail.c om

Apply

Network

and acquires IP address automatically.

DHCP

Network

SSL 465

TLS 587

UPnP

, in

IP Address

TCP/IP

You need to enable SMTP service in your mailbox.

, enter the local area IP address of the router or

Page 64

Figure 6-39 UPnP

Operation Manual

Step 2 Click next to

Step 3 Click

6.3.7 SNMP

SNMP (Simple Network Management Protocol), which can be used to enable software such as MIB

Builder and MG-SOFT MIB Browser to connect to the camera and manage and monitor the camera.

Prerequisites

●

Install SNMP monitoring and managing tools such as MIB Builder and MG-SOFT MIB Browser.

●

Get the MIB file of the matched version from technical support.

Procedure

Step 1 Select >

Enable

●

Select

●

Select

Open web browser on PC, enter http://

then you can visit the local area device with corresponding port.

Custom

Default

automatically, and you cannot edit mapping relation.

Apply

, click and then you can change external port as needed.

, and then the system finishes mapping with unoccupied port

Network

, and there are two mapping modes:

wide area IP address: external port number

SNMP

Custom

and

Default

, and

Page 65

Figure 6-40 SNMP (1)

Figure 6-41 SNMP (2)

Operation Manual

Step 2 Select SNMP version to enable SNMP.

●

Select V1, and the system can only process information of V1 version.

●

Select V2, and the system can only process information of V2 version.

●

Select V3, and then V1 and

password and authentication type. It requires corresponding username, password and

become unavailable. You can configure username,

Page 66

authentication type to visit your device from the server.

Using V1 and V2 might cause data leakage, and V3 is recommended.

Step 3 In

Parameter Description

SNMP Port The listening port of the software agent in the device.

Read Community, Write Community

Trap Address

Browser installed, and leave other parameters to the default.

, enter the IP address of the PC that has MIB Builder and MG-SOFT MIB

Table 6-17 Description of SNMP parameters

The read and write community string that the software agent supports.

You can enter number, letter, underline and dash to form the

name.

Operation Manual

Trap Address

Trap Port

Read-only Username

Read/Write Username

Authentication Type

Authentication Password It should be no less than 8 digits.

Encryption Type The default is CBC-DES.

Encryption Password It should be no less than 8 digits.

Step 4 Click

Apply

The target address of the Trap information sent by the software agent in the device.

The target port of the Trap information sent by the software agent in the device.

Set the read-only username accessing device, and it is default.

You can enter number, letter, and underline to form the name.

Set the read/write username access device, and it is default.

You can enter number, letter, and underline to form the name.

You can select from

MD5

and

. The default type is

SHA

public

private

MD5

Result

View device configuration through MIB Builder or MG-SOFT MIB Browser.

1. Run MIB Builder and MG-SOFT MIB Browser.

2. Compile the two MIB files with MIB Builder.

3. Load the generated modules with MG-SOFT MIB Browser.

4. Enter the IP address of the device you need to manage in the MG-SOFT MIB Browser, and then

select version to search.

5. Unfold all the tree lists displayed in the MG-SOFT MIB Browser, and then you can view the

configuration information, video channel amount, audio channel amount, and software version.

Page 67

Use PC with Windows and disable SNMP Trap service. The MG-SOFT MIB Browser will display prompt

when alarm is triggered.

6.3.8 Bonjour

Enable this function, and the OS and clients that support Bonjour would find the camera

automatically. You can have quick visit to the camera with Safari browser.

Bonjour is enabled by default.

Procedure

Step 1 Select >

Network

Bonjour

Figure 6-42 Bonjour

Operation Manual

Step 2 Click , and then configure server name.

Step 3 Click

Result

In the OS and clients that support Bonjour, follow the steps below to visit the network camera with

Safari browser.

1. Click

2. Enable

3. Click the camera to visit the corresponding web page.

Show All Bookmarks

Bonjour

enabled in the LAN.

6.3.9 Multicast

When multiple users are viewing the device video image simultaneously through network, it might

fail due to limited bandwidth. You can solve this problem by setting up a multicast IP (224.0.1.0–

238.255.255.255) for the camera and adopt the multicast protocol.

Apply

in Safari.

. The OS or client automatically detects the network cameras with Bonjour

Procedure

Step 1 Select >

Network

Multicast

Page 68

Figure 6-43 Multicast

Step 2 Click , and enter IP address and port number.

Table 6-18 Description of multicast parameters

Parameter Description

Operation Manual

Multicast Address

Port

Step 3 Click

Result

On the

protocol.

page, select

Live

6.3.10 Register

After you enable this function, when the camera is connected into Internet, it will report the current

location to the specified server which acts as the transit to make it easier for the client software to

access the camera.

Procedure

Step 1 Select >

Apply

RTSP

Network

The multicast IP address of by default, and the range is 224.0.0.0–239.255.255.255.

The multicast port of corresponding stream:

Sub Stream1

1025–65500.

Multicast

: 40016;

, and then you can view the video image with multicast

Main Stream/Sub Stream

Sub Stream2

: 40032, and all the range is

is 224.1.2.4

Main Stream

: 40000;

Figure 6-44 Register

Step 2 Click , and then configure server name.

Table 6-19 Description of register parameters

Parameter Description

Server Address The IP address or domain name of the server to be registered.

Page 69

Parameter Description

Port The port for registration.

Sub-Device ID The custom ID for the camera.

Step 3 Click

6.3.11 QoS

You can solve problems such as network delay and congestion with this function. It helps to assure

bandwidth, reduce transmission delay, packet loss rate, and delay jitter to improve experience.

0–63 means 64 degrees of priority; 0 for the lowest and 63 the highest.

Procedure

Step 1 Select >

Apply

Network

QoS

Figure 6-45 QoS

Operation Manual

Step 2 Configure QoS parameters.

Parameter Description

Realtime Monitor

Command

Step 3 Click

Save

6.3.12 Platform Access

6.3.12.1 P2P

P2P (peer-to-peer) technology enables users to manage devices easily without requiring DDNS, port

mapping or transit server.

Scan the QR code with your smartphone, and then you can add and manage more devices on the

mobile phone client.

Table 6-20 Description of QoS parameters

Configure the priority of the data packets that used for network surveillance. 0 for the lowest and 63 the highest.

Configure the priority of the data packets that used for configure or checking.

Procedure

Step 1 Select >

Network

Platform Access

P2P

Page 70

Figure 6-46 P2P

●

When P2P is enabled, remote management on device is supported.

●

When P2P is enabled and the device accesses to the network, the status shows online.

The information of the IP address, MAC address, device name, and device SN will be

collected. The collected information is for remote access only. You can cancel

selection to reject the collection.

Step 2 Log in to mobile phone client and tap

Step 3 Tap + at the upper-right corner.

Step 4 Scan the QR code on the

Step 5 Follow the instructions to finish the settings.

P2P

page.

Device management

Operation Manual

Enable

6.3.12.2 ONVIF

The ONVIF verification is enabled by default, which allows the network video products (including

video recording device and other recording devices) from other manufacturers to connect to your

device.

ONVIF is enabled by default.

Procedure

Step 1 Select >

Step 2 Click next to

Step 3 Click

Apply

Network

Platform Access

Figure 6-47 ONVIF

ONVIF Verification

ONVIF

Page 71

6.3.12.3 RTMP

Through RTMP, you can access a third-party platform (such as Ali and YouTube) to realize video live

view.

●

RTMP can be configured by admin only.

●

RTMP supports the H.264, H.264 B and H.264H video formats, and the AAC audio format only.

Procedure

Step 1 Select >

Network

Platform Access

Figure 6-48 RTMP

RTMP

Operation Manual

Step 2 Click .

Make sure that the IP address is trustable when enabling RTMP.

Step 3 Configure RTMP parameters.

Table 6-21 Description of RTMP parameters

Parameter Description

Stream Type

Address Type

The stream for live view. Make sure that the video format is H.264, H.264 B and H.264H, and the audio format is AAC.

●

Non-custom

●

Custom

: Enter the server IP and domain name.

: Enter the path allocated by the server.

IP Address

Port

Custom Address

Step 4 Click

Apply

When selecting and port.

●

IP address

●

: Keep the default value.

Port

When selecting the server.

Non-custom

: Support IPv4 or domain name.

Custom

, you need to enter server IP address

, you need to enter the path allocated by

Page 72

6.3.13 Basic Service

Configure the IP hosts (devices with IP address) that are allowed to visit the device. Only the hosts in

the trusted sites list can log in to the web page. This is to enhance network and data security.

Procedure

Step 1 Select >

Network

Basic Service

Figure 6-49 Basic service

Operation Manual

Step 2 Enable the basic service according to the actual needs.

Table 6-22 Description of basic service parameters

Function Description

SSH

Multicast/Broadcast Search

CGI

Onvif

Genetec

Mobile Push Notification

Private Protocol Authentication Mode

Step 3 Click

Apply

You can enable SSH authentication to perform safety management.

Enable this function, and then when multiple users are viewing the device video image simultaneously through network, they can find your device with multicast/broadcast protocol.

Enable the function, and then other devices can access through this service. The function is enabled by default.

Enable this function, and then the system will send the snapshot that was taken when alarm is triggered to your phone, this is enabled by default.

Select the authentication mode from

Compatible Mode

. Security mode is recommended.

Security Mode

and

Page 73

6.4 EPTZ

EPTZ function can simultaneously zoom in and track multiple humans and vehicles that trigger

alarms. It provides rich details and a panoramic view at the same time.

This function is only available on select devices.

Procedure

Step 1 Select >

PTZ

EPTZ Linkage

Figure 6-50 EPTZ

Operation Manual

Step 2 Enable this function and select the display mode.

Table 6-23 Description of display modes

Mode Description

Displays the original screen.

Displays the original image screen + 1 sub-screen.

Displays the original image screen + 3 sub-screens.

You can zoom or drag

the sub-screen

images in the original

screen.

Step 3 (Optional) Enable the

the dropdown list.

●

Custom: Select the tracking duration time manually. For example, if you set from 30 s to

Displays the original image screen + 5 sub-screens.

60 s, after tracking object A for 30 seconds, if object B appears, the camera will start

tracking object B; if no other object appears in the process of tracking A, the camera will

Linkage Track

checkbox and select tracking duration mode from

Page 74

stop tracking object A after 60 seconds.

●

Continue till object disappears: The camera will stop tracking when the detected object

disappears in the image.

Step 4 Click

Apply

6.5 Event

6.5.1 Setting Alarm Linkage

6.5.1.1 Setting Alarm-in

When an alarm is triggered by the device connected to the alarm-in port, the system performs the

defined alarm linkage.

Procedure

Step 1 Select >

Step 2 Click next to

Event

Alarm

Enable

Operation Manual

to enable alarm linkage.

Figure 6-51 Alarm linkage

Step 3 Select an alarm-in port and a sensor type.

Page 75

●

Sensor Type: NO or NC.

●

Anti-Dither: Only record one alarm event during the anti-dither period.

Step 4 Select the schedule and arming periods and alarm linkage action. If the schedules cannot

meet the scene requirement, you can click

see "6.5.1.2.1 Adding Schedule".

Step 5 Click

Apply

6.5.1.2 Alarm Linkage

When configuring alarm events, select alarm linkages (such as record, snapshot). When the

corresponding alarm is triggered in the configured arming period, the system will alarm.

Select >

Event

, and then click next to

Alarm

Figure 6-52 Alarm linkage

Add Schedule

Enable

to enable alarm linkage.

Operation Manual

to add new schedule. For details,

6.5.1.2.1 Adding Schedule

Set arming periods. The system only performs corresponding linkage action in the configured

period.

Procedure

Step 1 Click

Add Schedule

next to

Schedule

Page 76

Figure 6-53 Schedule

Operation Manual

Step 2 Press and drag the left mouse button on the timeline to set arming periods. Alarms will be

triggered in the period in green on the timeline.

●

Click

●

You can set 6 periods per day.

Step 3 Click

Step 4 (Optional) Click

You can:

●

Double-click the table name to edit it.

●

Click to delete the table as needed.

Copy

page, you can copy the configuration to the selected days. Select the

box to select all days to copy the configuration.

Apply

6.5.1.2.2 Record Linkage

The system can link record channel when an alarm event occurs. After alarm, the system stops

recording after an extended period according to the

Prerequisites

●

After the corresponding alarm type (

links recording. For details, see "10.3 Setting Record Plan".

●

Enable auto record mode, the record linkage will take effect. For details, see "10.2 Setting Record

Control".

next to a day, and select the days that you want to copy to in the prompt

Select All

Time Plan Table

to add a new time plan table.

Post-Record

Normal, Motion

, or

setting.

Alarm

) is enabled, the record channel

check

Setting Record Linkage

On the

Post-Record

After

Post-Record

page, click to enable record linkage, select the channel as needed, and set

Alarm

to set alarm linkage and record delay.

is configured, alarm recording continues for an extended period after the alarm

Page 77

ends.

6.5.1.2.3 Snapshot Linkage

After snapshot linkage is configured, the system can automatically alarm and take snapshots when

an alarm is triggered.

Prerequisites

Operation Manual

Figure 6-54 Record linkage

After the corresponding alarm type (

links capturing picture. For details, see "10.3 Setting Record Plan".

Setting Record Linkage

On the

6.5.1.2.4 Alarm-out Linkage

When an alarm is triggered, the system can automatically link with alarm-out device.

On the

configure

When alarm delay is configured, alarm continues for an extended period after the alarm ends.

page, click to enable snapshot linkage, and select the channel as needed.

Alarm

page, click to enable alarm-out linkage, select the channel as needed, and then

Alarm

Post alarm

Normal, Motion

Figure 6-55 Snapshot linkage

Figure 6-56 Alarm-out linkage

, or

Alarm

) is enabled, the snapshot channel

6.5.1.2.5 Email Linkage

When an alarm is triggered, the system will automatically send an email to users.

Email linkage takes effect only when SMTP is configured. For details, see "6.3.5 Email".

Figure 6-57 Email linkage

Page 78

6.5.1.3 Subscribing Alarm

6.5.1.3.1 Alarm Types

Alarm Type Description Preparation

Operation Manual

Table 6-24 Description of alarm types

Motion Detection

Disk Full

Disk Error

Video Tampering

External Alarm

Audio Detection

IVS

The alarm is triggered when moving object is detected.

The alarm is triggered when the free space of SD card is less than the configured value.

The alarm is triggered when there is failure or malfunction in the SD card.

The alarm is triggered when the camera lens is covered or there is defocus in video images.

The alarm is triggered when there is external alarm input.

The alarm is triggered when there is audio connection problem.

The alarm is triggered when intelligent rule is triggered.

Motion detection is enabled. For details, see "6.5.3.1 Setting Motion Detection".

The SD card no space function is enabled. For details, see "6.5.2.1 Setting SD Card Exception".

SD card failure detection is enabled. For details, see "6.5.2.1 Setting SD Card Exception".

Video tampering is enabled. For details, see "6.5.3.2 Setting Video Tampering".

The device has alarm input port and external alarm function is enabled. For details, see "6.5.1.1 Setting Alarm-in".

Abnormal audio detection is enabled. For details, see "6.5.4 Setting Audio Detection".

Enable IVS, crowd map, face detection or people counting, and other intelligent functions.

The alarm is triggered when the

Scene Changing

Voltage Detection

Security Exception

device monitoring scene changes.

The alarm is triggered when the device detects abnormal voltage input.

The alarm is triggered when the device detects malicious attack.

6.5.1.3.2 Subscribing Alarm Information

Background Information

You can subscribe alarm event. When a subscribed alarm event is triggered, the system records

detailed alarm information at the right side of the page.

Functions of different devices might vary.

Procedure

Scene changing detection is enabled. For details, see "6.5.3.3 Setting Scene Changing".

Voltage detection is enabled. For details, see "6.5.2.3 Setting Voltage Detection".

Security exception is enabled. For details, see "9.1 Security Status".

Page 79

Step 1 Click at the right-upper corner of the main page.

Figure 6-58 Alarm (subscription)

Operation Manual

Step 2 Click next to

Step 3 Select alarm type according to the actual need. For details, see "6.5.1.3.2 Subscribing Alarm

Information".

The system prompts and records alarm information according to actual conditions.

When the subscribed alarm event is triggered and the alarm subscription page is not

displayed, a number is displayed on , and the alarm information is recorded

automatically. Click to view the details in the alarm list. You can click

record.

Step 4 Click next to

The system will play the selected audio file when the selected alarm is triggered.

6.5.2 Setting Exception

Abnormality includes SD card, network, illegal access, voltage detection, and security exception.

Only the device with SD card has the abnormality functions, including

and

Capacity Warning

Enable Alarm

Play Alarm Tone

, and select the tone path.

No SD Card, SD Card Error

Clear

to clear the

Page 80

6.5.2.1 Setting SD Card Exception

Operation Manual

In case of SD card exception, the system performs alarm linkage. The event types include

Card, Low SD Card Space

Procedure

Step 1 Select >

Step 2 Click to enable the SD card detection functions.

Step 3 Set alarm linkage actions. For details, see "6.5.1.2 Alarm Linkage".

Step 4 Click

, and

SD Card Error

Event

When enabling

card is less than this value, the alarm is triggered.

Apply

Exception

Figure 6-59 SD card exception

Low SD Card Space

. Functions might vary with different models.

SD Card Exception

, set

Capacity Limit

No SD

. When the remaining space of SD

6.5.2.2 Setting Network Exception

In case of network abnormality, the system performs alarm linkage. The event types include

and

IP Conflict

Procedure

Step 1 Select >

Event

Exception

Network Exception

Offline

Page 81

Figure 6-60 Network exception

Operation Manual

Step 2 Click to enable the network detection function.

Step 3 Set alarm linkage actions. For details, see "6.5.1.2 Alarm Linkage".

Step 4 Click

Apply

6.5.2.3 Setting Voltage Detection

When the input voltage is higher than or lower than the rated value of the device, the system

performs alarm linkage.

Procedure

Step 1 Select >

Event

Exception

Voltage Detection

Page 82

Figure 6-61 Voltage detection

Step 2 Click to enable the voltage detection function.

When enabling

Overlay

, the alarm icon is displayed by overlapping when the alarm is

triggered.

Step 3 Set alarm linkage actions. For details, see "6.5.1.2 Alarm Linkage".

Step 4 Click

Apply

Operation Manual

6.5.3 Setting Video Detection

Check whether there are considerable changes on the video by analyzing video images. In case of

any considerable change on the video (such as moving object and fuzzy image), the system

performs an alarm linkage.

6.5.3.1 Setting Motion Detection

The system performs an alarm linkage when a moving object appears in the image and its moving

speed reaches the configured sensitivity.

●

If you enable motion detection and smart motion detection simultaneously, and configure the

linked activities, the linked activities take effect as follows:

◇

When motion detection is triggered, the camera will record and take snapshots, but other

configured linkages such as sending emails, PTZ operation will not take effect.

◇

When smart motion detection is triggered, all the configured linkages take effect.

●

If you only enable motion detection, all the configured linkages take effect when motion

detection is triggered.

Procedure

Step 1 Select >

Event

Video Detection

Motion Detection

Page 83

Figure 6-62 Motion detection

Operation Manual

Step 2 Click to enable the motion detection function.

Step 3 Set the area for motion detection.

1) Click

Setting

next to

Area

Figure 6-63 Area

2) Select a color and set the region name. Select an effective area for motion detection in

the image and set

Sensitivity

and

Threshold

●

Select a color on to set different detection parameters for each

region.

●

Sensitivity: Sensitive degree of outside changes. It is easier to trigger the alarm with

higher sensitivity.

●

Threshold: Effective area threshold for motion detection. The smaller the threshold

is, the easier the alarm is triggered.

●

The whole video image is the effective area for motion detection by default.

●

The red line in the waveform indicates that the motion detection is triggered, and

Page 84

the green one indicates that there is no motion detection. Adjust sensitivity and

threshold according to the waveform.

3) Click OK.

Step 4 Set arming periods and alarm linkage action. For details, see "6.5.1.2 Alarm Linkage".

If the exiting schedules cannot meet the scene requirement, you can click

to add a new schedule. For details, see "6.5.1.2.1 Adding Schedule".

Anti-dither: After the

event in the period.

Step 5 Click

Apply

Anti-dither

6.5.3.2 Setting Video Tampering

The system performs alarm linkage when the lens is covered or video output is mono-color screen

caused by light and other reasons.

Procedure

Step 1 Select >

Step 2 Select the event type.

●

Video Tampering

exceed the configured values, an alarm will be triggered.

●

Defocus Detection

function is available on select models.

Event

Video Detection

: When the percentage of the tampered image and the duration

: When the image is blurred, an alarm will be triggered. This

Operation Manual

Add Schedule

time is set, the system only records one motion detection

Video Tampering

Figure 6-64 Video tampering

Page 85

Table 6-25 Description of video temper parameter

Parameter Description

Operation Manual

Covered Area

Duration

Anti-Dither Only record one alarm event during the anti-dither period.

Step 3 Set arming periods and alarm linkage action. For details, see "6.5.1.2 Alarm Linkage".

If the exiting schedules cannot meet the scene requirement, you can click

to add a new schedule. For details, see "6.5.1.2.1 Adding Schedule".

Step 4 Click

Apply

When the percentage of the tampered image and the duration exceed the configured values, an alarm will be triggered.

6.5.3.3 Setting Scene Changing

The system performs alarm linkage when the image switches from the current scene to another one.

Procedure

Step 1 Select >

Event

Video Detection

Figure 6-65 Scene changing

Scene Changing

Add Schedule

Step 2 Select the schedule and arming periods and alarm linkage action. For details, see "6.5.1.2

Alarm Linkage".

If the exiting schedules cannot meet the scene requirement, you can click

to add a new schedule. For details, see "6.5.1.2.1 Adding Schedule".

Step 3 Click

Apply

6.5.4 Setting Audio Detection

The system performs alarm linkage when vague voice, tone change, or rapid change of sound

intensity is detected.

Add Schedule

Procedure

Step 1 Select >

Event

Video Detection

Audio Detection

Page 86

Figure 6-66 Audio detection

Operation Manual

Step 2 Set parameters.

●

Step 3 Select the schedule and arming periods and alarm linkage action. For details, see "6.5.1.2

Alarm Linkage".

If the exiting schedules cannot meet the scene requirement, you can click

to add a new schedule. For details, see "6.5.1.2.1 Adding Schedule".

Step 4 Click

6.6 Storage

Input abnormal: Click next to

Audio Abnormal

, and the alarm is triggered when

the system detects abnormal sound input.

Intensity change: Click next to

Threshold

. The alarm is triggered when the system detects that the sound intensity

Intensity Change

, and then set

Sensitivity

exceeds the configured threshold.

◇

It is easier to trigger the alarm with higher sensitivity or smaller threshold. Set a high

threshold for noisy environment.

◇

The red line in the waveform indicates audio detection is triggered, and the green

one indicates no audio detection. Adjust sensitivity and threshold according to the

waveform.

Add Schedule

Apply

and

Displays the information of the local SD card. You can set it as read only or read & write; you can also

Page 87

Operation Manual

hot swap and format SD card.

Functions might vary with different models.

Select >

●

Click

●

Click

●

Click

●

Click

Read-Only

Read & Write

Hot Swap

Format

Storage

, and then the SD card is set to read only.

, and then the SD card is set to read & write.

, and then you can pull out the SD card.

, and you can format the SD card.

When reading SD card on PC, if the SD card capacity is much less than the nominal capacity, you

need to format the SD card. Then the data in SD card will be cleared, and the SD card is formatted

to be private file system. The private file system can greatly improve SD card multimedia file

read/write performance. Download Diskmanager from Toolbox to read the SD card. For details,

contact after-sales technicians.

Figure 6-67 Local

6.7 System

This section introduces system configurations, including general, date & time, account, safety, PTZ

settings, default, import/export, remote, auto maintain and upgrade.

6.7.1 General

6.7.1.1 Basic

You can configure device name, language and video standard.

Procedure

Step 1 Select >

System

General

Figure 6-68 Basic

Basic

Step 2 Configure general parameters.

Page 88

Table 6-26 Description of general parameters

Parameter Description

Name Enter the device name.

Operation Manual

Video Standard Select video standard from

Step 3 Click

Apply

6.7.1.2 Date & Time

You can configure date and time format, time zone, current time, DST (Daylight Saving Time) or NTP

server.

Procedure

Step 1 Select >

System

General

Figure 6-69 Date and time

Date & Time

and

PAL

NTSC

Step 2 Configure date and time parameters.

Table 6-27 Description of date and time parameters

Parameter Description

Date Format Configure the date format.

Page 89

Parameter Description

●

Manually Setting

●

: When selecting NTP, the system then syncs time with the

NTP

Time

internet server in real time.

You can also enter the IP address, time zone, port, and interval of a

PC which installed NTP server to use NTP.

Operation Manual

: Configure the parameters manually.

Time Format Configure the time format. You can select from

Time Zone Configure the time zone that the camera is at.

Current Time

DST

Step 3 Click

6.7.2 Account

You can manage users, such as add, delete, or edit them. Users include admin, added users and

ONVIF users.

Managing users and groups are only available for administrator users.

●

The max length of the user or group name is 31 characters which consists of number, letter,

underline, dash, dot and @.

●

The password must consist of 8 to 32 non-blank characters and contain at least two types of

characters among upper case, lower case, number, and special character (excluding ' " ; : &).

●

You can have 18 users and 8 groups at most.

●

You can manage users through single user or group, and duplicate usernames or group names

are not allowed. A user can only be in one group at a time, and the group users can own

authorities within group authority range.

●

Online users cannot edit their own authority.

●

There is one admin by default which has highest authority.

●

Select

Anonymous Login

password. Anonymous users only have preview authorities. During anonymous login, click

Logout

, and then you can log in with other username.

Apply

12-Hour

Configure system time.

Click

Sync PC

Enable DST as needed.

Click , and configure start time and end time of DST with

Week

, and then log in with only IP address instead of username and

, and the system time changes to the PC time.

24-Hour

Date

6.7.2.1 User

6.7.2.1.1 Adding User

You are admin user by default. You can add users, and configure different permissions.

Procedure

Step 1 Select >

System

Account

User

Page 90

Figure 6-70 User

Operation Manual

Step 2 Click

Add

Figure 6-71 Add user (system)

Page 91

Figure 6-72 Add user (restricted login)

Operation Manual

Step 3 Configure user parameters.

Table 6-28 Description of user parameters

Parameter Description

Username User’s unique identification. You cannot use existed username.

Password Enter password and confirm it again.

The password must consist of 8 to 32 non-blank characters and

Confirm Password

Group The group that users belong to. Each group has different authorities.

Remark Describe the user.

System

Live Select the live view authority for the user to be added.

Search Select the search authority for the user to be added.

contain at least two types of characters among upper case, lower case, number, and special character (excluding ' " ; : &).

Select authorities as needed.

We recommend giving fewer permissions to normal users than

premium users.

Page 92

Parameter Description

Restricted Login

Step 4 Click

The newly added user is displayed in the username list.

Related Operations

●

click to edit password, group, memo or authorities.

Apply

Operation Manual

Set the PC address that allows the defined user to log in to the camera and the validity period and time range. You can log in to the web page with the defined IP in the defined time range of validity period.

●

IP address: You can log in to web through the PC with the set IP.

●

Validity period: You can log in to web in the set validity period.

●

Time range: You can log in to web in the set time range.

Set as follows

1. IP address: Enter the IP address of the host to be added.

2. IP segment: Enter the start address and end address of the host

to be added.

For admin account, you can only edit the password.

●

Click to delete the added users. Admin user cannot be deleted.

The admin account cannot be deleted.

6.7.2.1.2 Resetting Password

Enable the function, and you can reset password by clicking

For details, see "4.2 Resetting Password".

Procedure

Step 1 Select >

System

Account

Figure 6-73 User

User

Forget password?

on the login page.

Page 93

Operation Manual

Step 2 Click next to

If the function is not enabled, you can only reset the password by resetting the camera.

Step 3 Enter the reserved email address.

Step 4 Click

Apply

6.7.2.2 Adding User Group

You have two groups named admin and user by default, and you can add new group, delete added

group or edit group authority and memo.

Procedure

Step 1 Select >

System

Enable

Password Reset

Account

Figure 6-74 Group name

Group

Step 2 Click

Step 3 Enter the group name and memo, and then select group authorities.

Step 4 Click OK to finish configuration.

The newly added group displays in the group name list.

Add

Figure 6-75 Add group

Related Operations

●

Click to edit password, group, memo or authorities.

●

Click to delete the added users. Admin user cannot be deleted.

Page 94

The admin group and user group cannot be deleted.

6.7.2.3 ONVIF User

You can add, delete ONVIF user, and change their passwords.

Procedure

Step 1 Select >

System

Account

Figure 6-76 ONVIF user

ONVIF User

Operation Manual

Step 2 Click

Step 3 Configure user parameters.

Parameter Description

Username User’s unique identification. You cannot use existed username.

Password Enter password and confirm it again.

Confirm Password

Add

Figure 6-77 Add ONVIF user

Table 6-29 Description of ONVIF user parameters

The password must consist of 8 to 32 non-blank characters and contain at least two types of characters among upper case, lower case, number, and special character (excluding ' " ; : &).

Group Name

Step 4 Click OK.

The newly added user displays in the username list.

Related Operations

●

Click to edit password, group, memo or authorities.

The group that users belong to. Each group has different authorities.

Page 95

For admin account, you can only change the password.

●

Click to delete the added users.

The admin account cannot be deleted.

6.7.3 Peripheral Management

6.7.3.1 Configuring Serial Port

Set the serial port of the external device.

Procedure

Step 1 Select >

Step 2 Configure parameters.

System

Peripheral

Figure 6-78 Serial port settings

Serial Port

Operation Manual

Table 6-30 Description of serial port settings parameters

Parameter Description

Enter the corresponding device address. It is 1 by default.

IP Address

Baud Rate

Data Bits It is 8 by default.

Stop Bits

Make sure that the address is the same as the device address; otherwise you

cannot control the device.

Configure device baud rate. It is

It is 1 by default.

9600

by default.

Parity

Step 3 Click

Apply

It is

None

by default.

Page 96

6.7.3.2 Configuring External Light

You need to configure external light mode when the external light is used.

Prerequisites

●

Connect external light with RS-485 port.

●

You have configured serial port parameters. For details, see "6.7.3.1 Configuring Serial Port".

Procedure

Step 1 >

Step 2 Select working mode as needed.

System

Peripheral

Figure 6-79 External light

External Light

Operation Manual

Table 6-31 Lamp parameters

Parameter Description

●

: The external light is disabled.

Off

●

Work Mode

Auto Mode

Light Brightness

Manual

●

Set the brightness of the external light.

: The camera turns on or turns off the light according to the light

Auto

time and photoresister automatically.

: When selecting

Time

During the arming period, the external light is on.

Select the added time plan table in the

Schedule

Linkage".

Photoresister

camera turns on the external light according to the brightness automatically.

For some models, you can set the brightness of each external light

separately.

: Set the light brightness manually.

Time

to add new time plan table. For details, see "6.5.1.2 Alarm

: When you select

Auto Mode

Photoresister

, set the arming period.

Time Plan

list. Click

Auto Mode

Add

, the

Step 3 Click

Apply

Page 97

6.7.3.3 Configuring Wiper

Procedure

Step 1

Step 2 Configure working mode of wipers.

Select

> >

System

Peripheral

Figure 6-80 Wiper

Wiper

Operation Manual

Parameter Description

Interval

Start, Stop, Once

Wash

Step 3 Click

Apply

6.7.4 Manager

6.7.4.1 Requirements

To make sure the system runs normally, maintain it as the following requirements:

●

Check surveillance images regularly.

●

Clear regularly user and user group information that are not frequently used.

●

Change the password every three months. For details, see "6.7.2 Account".

●

View system logs and analyze them, and process the abnormity in time.

●

Back up the system configuration regularly.

●

Restart the device and delete the old files regularly.

●

Upgrade firmware in time.

Table 6-32 Wiper parameter description

The interval between stop mode and start mode. For example, set the time to 10 s, and the wiper will work every 10 s.

Configure working mode of the wiper.

●

Click

●

Click

●

Click

Select the work as the configured time. Click be used to check whether the wiper works normally.

, and the wiper works as the set interval time.

Start

, and the wiper stops working.

Stop

, and the wiper works once.

Once

Schedule

check box and set the time, and then the wiper will

, and the wiper works once. It can

Once

Page 98

6.7.4.2 Maintenance

You can restart the system manually, and set the time of auto reboot and auto deleting old files. This

function is disabled by default.

Procedure

Step 1 Select >

System

Manager

Figure 6-81 Maintenance

Maintenance

Operation Manual

Step 2 Configure auto maintain parameters.

●

Click next to

system will automatically restarts at the set time every week.

●

Click next to

will automatically deletes old files at the set time. The time range is 1 to 31 days.

When you enable and confirm the

restored. Operate it carefully.

Step 3 Click

Apply

6.7.4.3 Import/Export

●

Export the system configuration file to back up the system configuration.

●

Import system configuration file to make quick configuration or recover system configuration.

Procedure

Step 1 Select >

System

Auto Reboot

Auto Delete

Manager

Restart System

Delete Old Files

Auto Delete

Import/Export

, and set the reboot time, then the

, and set the time, then the system

function, the deleted files cannot be

Page 99

Step 2 Import or export the file.

●

6.7.4.4 Default

Figure 6-82 Import/Export

Import: Select local configuration file, and click

configuration file to the system.

Export: Click

storage.

Export Configuration file

to export the system configuration file to local

Import File

Operation Manual

to import the local system

Restore the device to default configuration or factory settings.

Select >

●

Click

●

Click

Default

Factory Default

System

Manager

, and then all the configurations except IP address and account are reset to default.

, and all the configurations are reset to factory settings.

Default

Figure 6-83 Default

6.7.5 Upgrade

Upgrading to the latest system can refine camera functions and improve stability.

If wrong upgrade file has been used, restart the device; otherwise some functions might not work

properly.

Page 100

Procedure

Step 1 Select >

System

Upgrade

Figure 6-84 Upgrade

Operation Manual

Step 2 Click

The upgrade file should be a .bin file.

Step 3 Click

Browse

Update

, and then upload upgrade file.

6.8 System Information

You can view the information, including version, log and online user, and back up or clear log.

6.8.1 Version

Select >

and web version.

System Info

6.8.2 Online User

Select >

System Info

Version

Online User

to view device information such as hardware, system version,

to view all the online users logging in to web.

6.9 Setting Log

6.9.1 Log

You can view and back up logs.

Procedure

Step 1 Select >

Step 2 Configure

The start time should be later than January 1, 2000, and the end time should be earlier

than December 31, 2037.

The log type includes All, System, Setting, Data, Event, Record, Account, and Security.

●

System

closedown, device reboot, system reboot, and system upgrade.

●

Setting

●

Data

Log

and

End Time

, and then select the log type.

Log

Start Time

: Includes program start, abnormal close, close, program reboot, device

: Includes saving configuration and deleting configuration file.

: Includes configuring disk type, clearing data, hot swap, FTP state, and record

Dahua Dahua Technology DH-IPC-HDBW1430DE-SW Dome IP Overvågningskamera (2560x1440) User manual [EN]

Specifications and Main Features

Frequently Asked Questions

User Manual

Foreword

Important Safeguards and Warnings

1 Overview

1.1 Introduction

1.2 Network Connection

1.3 Functions

1.3.1 Basic Functions

1.3.2 AI Functions

2 Configuration Flow

3 Device Initialization

4.1 Device Login

4 Login

4.2 Resetting Password

5 Home Page

6.1 Local

6 Setting

6.2 Camera

6.2.1 Setting Image Parameters

6.2.1.1 Page Layout

6.2.1.2 AI SSA

6.2.1.3 Image

6.2.1.4 Exposure

6.2.1.5 Backlight

6.2.1.6 WB

6.2.1.7 Day/Night

6.2.1.8 Illuminator

6.2.1.9 Defog

6.2.1.10 AFSA

6.2.1.11 Fisheye

6.2.2 Setting Encode Parameters

6.2.2.1 Encode

6.2.2.2 Overlay

6.2.2.2.1 Configuring Privacy Masking

6.2.2.2.2 Configuring Channel Title

6.2.2.2.3 Configuring Time Title

6.2.2.2.4 Configuring Location

6.2.2.2.5 Configuring Font Properties

6.2.2.2.6 Configuring Picture Overlay

6.2.2.2.7 Configuring Custom Title

6.2.2.2.8 Configuring Target Statistics

6.2.2.2.9 Configuring ANPR

6.2.2.2.10 Configuring Face Detection

6.2.2.2.11 Configuring Face Recognition

6.2.2.2.12 Configuring Face Statistics

6.2.2.2.13 Configure Face&Body Counting

6.2.2.2.14 Configuring Parking Space

6.2.2.3 ROI

6.2.3 Splicing

6.2.4 Audio

6.2.4.1 Setting Audio Parameters

6.2.4.2 Setting Alarm Tone

6.3 Network

6.3.1 TCP/IP

6.3.2 Port

6.3.3 PPPoE

6.3.4 DDNS

6.3.5 Email

6.3.6 UPnP

6.3.7 SNMP

6.3.8 Bonjour

6.3.9 Multicast

6.3.10 Register

6.3.11 QoS

6.3.12 Platform Access

6.3.12.1 P2P

6.3.12.2 ONVIF

6.3.12.3 RTMP

6.3.13 Basic Service

6.4 EPTZ

6.5 Event

6.5.1 Setting Alarm Linkage

6.5.1.1 Setting Alarm-in

6.5.1.2 Alarm Linkage

6.5.1.2.1 Adding Schedule

6.5.1.2.2 Record Linkage

6.5.1.2.3 Snapshot Linkage