Page 1
DH-AX18
XXXXXX
User’s Manual
ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.
Address: No. 1399, Binxing Road, Binjiang District, Hangzhou, P. R. China Postcode: 310053
Website: www.dahuasecurity.com
Tel: +86-571-87688888 28933188
Email: dhoverseas@dhvisiontech.com
This manual introduces the installation, functions and operations of the
Foreword
DH-AX18 device (hereinafter referred to as "the Device"). Read carefully
before using the device, and keep the manual safe for future reference.
Safety Instructions
The following signal words might appear in the manual.
Sig nal Wo rds Meaning
Indica tes a high potential ha zard which, if not avoided, will re sult in
death or se rious injury.
Indica tes a medium or low potential ha zard which, if no t a voided,
could res ult in slight or moderate injury.
Indica tes a potential ris k which, if not avoided, could res ult in property
dama ge, da ta loss , reduc tions in pe rformance, or unpredictable
res ults.
P rovides methods to help you solve a problem or s ave time.
About the Manual
●
The manual is for reference only. Slight dierences might be found
between the manual and the product.
●
We are not liable for losses incurred due to operating the product in
ways that are not in compliance with the manual.
●
The manual will be updated according to the latest laws and
regulations of related jurisdictions. For detailed information, see
the paper user’s manual, use our CD-ROM, scan the QR code or
visit our ocial website. The manual is for reference only. Slight
dierences might be found between the electronic version and the
paper version.
●
There might be errors in the print or deviations in the description of
the functions, operations and technical data. If there is any doubt or
dispute, we reserve the right of nal explanation.
Upgrade the reader software or try other mainstream reader
●
software if the manual (in PDF format) cannot be opened.
P rovides a dditional information as a supplement to the text.
Important Safeguards and Warnings
This section introduces content covering the proper handling of the
device, hazard prevention, and prevention of property damage. Read
carefully before using the device, and comply with the guidelines when
using it.
●
Tra nsport the device under a llowed humidity and tempera ture
conditions. Refer to the technical parameters for requirements on
the transporting temperature and humidity of the device.
Storage Requirements
●
Store the device under allowed humidity and temperature
conditions. Refer to the technical parameters for requirements on
the storing temperature and humidity of the device.
Installation Requirements
●
Do not connect the power adapter to the device while the adapter
is powered on.
●
Strictly comply with the local electrical safety code and standards.
Make sure the ambient voltage is stable and meets the power
supply requirements of the device.
●
Personnel working at heights must take all necessary measures to
ensure personal safety including wearing a helmet and safety belts.
●
Do not leave outdoor models of the device hanging in the air or
facing outwards when installing onto poles that are on top of
buildings.
Do not place the device in a place exposed to sunlight or near
●
heat sources.
Put the device in a well-ventilated place, and do not block its
●
ventilation.
●
Use an adapter or cabinet power supply provided by the
manufacturer.
●
Do not connect the device to two or more kinds of power supplies,
to avoid damage to the device.
●
The device is a class I electrical appliance. Make sure that the power supply
of the device is connected to a power socket with protective earthing.
To ensure heat dissipation, the gap between the device and the
●
surrounding area should not be less than 10 cm on the sides and
10 cm on top of the device.
When installing the device, make sure that the power plug and
●
appliance coupler can be easily reached to cut o power.
●
Voltage stabilizer and lightning surge protector are optional depending
on the actual power supply on site and the ambient environment.
Operation Requirements
●
Do not disassemble the device without professional instruction.
●
Operate the device within the rated range of power input and output.
●
Make sure that the power supply is correct before use.
●
Make sure the device is powered o before disassembling wires to
avoid personal injury.
●
Do not unplug the power cord on the side of the device while the
adapter is powered on.
●
Use the device under allowed humidity and temperature conditions.
●
Operating temperature: 0°C–40 °C (32 °F–104 °F)ns.
●
Do not drop or splash liquid onto the device, and make sure that there
is no object lled with liquid on the device to prevent liquid from
owing into it.
●
Do not block the ventilator of the device with objects, such as a
newspaper, table cloth or curtain.
●
Do not place an open ame on the device, such as a lit candle.
Maintenance Requirements
●
Do not disassemble it unless necessary.
Power o the device before maintenance.●
Mark key components on the maintenance circuit diagram with
●
warning signs.
Port and Indicator
Table 1-1 Indicator description
Status Description
Solid green
Solid red
Flashes
Internet access available.
Unable to access the Internet. (Router connected, but
network disconnected. )
Flashes quickly (T=240 ms) for120 s: WPS process.
Flashes slowly (T=2 s) for10 s: Resetting process.
Connection Diagram
Figure 2-1 Connection diagram
Connect your device to the
router through wireless.
Connect your device to the
router through Ethernet cable.
Table 2-1 Rear panel description
Number Description
Reset button. Press and hold the button for more than 5
1
seconds, and then the router will restore its factory defaults.
2
WPS button. Short press for WPS function.
LAN port. Connects to wired devices such as computers and
3
set top boxes.
WAN port. Connects to the modem or Ethernet port.
4
Power port. Connects to the power supply.
5
Ethernet cable
12 3 4 5
WPSWPS LAN1 LAN2 LAN3WAN
DC INRESET
Ethernet cable
Socket
Power
Connect to modem.
Modem
Ethernet cable
OR
Connect to Internet port.
Network port
Ethernet cable
Conguring the Router
3
You can initialize the device and log in to it through the device webpage
and WiLynk app.
3.1 App Conguration
You can initialize the device and log in to the app to congure the device.
●
For the rst time use or after the device is restored to its factory
defaults, you need to initialize the device.
To protect your device, keep the admin login password safe after
●
initialization, and change the password regularly.
●
For more details on app conguration, go to Me > User Manual
on WiLynk.
3.1.1 Downloading App
Scan the QR code to download the WiLynk app.
Figure 3-1 QR code
You can also search for WiLynk at the app store, and then download it.
3.1.2 Registering Accounts
Procedure
Step 1
Open WiLynk, tap Register, and then enter the Register page.
Step 2
Select the country or region, enter the email address or phone
number, enter the password, and then conrm it.
Phone number is only supported in select countries.
Step 3
Tap the I have read and agree checkbox.
You can click to view the user service agreement and privacy policy.
Step 4
Click Send.
Step 5
Enter the verication code, and then click OK.
Figure 3-2 Registration
3.1.3 Adding Devices
Prerequisites
Make sure that the device is connected with power and modem. After the
device is powered on, wait for 2 minutes, and then add devices.
Procedure
Step 1
On the Status page, tap Add Device or on the right-upper corner.
Figure 3-3 Preparations for adding device Figure 3-4 Add devices
Step 2 Scan the QR code on the device, or tap Select Type of the device, and
then enter the SN.
Step 3
Go to the Wi-Fi settings on your system settings, connect the router
SSID, and then tap Next.
Step 4
Congure the login password of the device, and then tap Next.
Congure the networking method of the device, and then tap Next.
Step 5
Step 6
Wait until the screen prompts Connect to Internet, and then tap Next.
Congure the time zone and DST of the device, congure the device
Step 7
SSID, and then tap Next to nish the conguration.
Figure 3-5 Congure time zone and Wi-Fi network
3.2 Web Conguration
You can initialize the device and log in to it through the device webpage.
Procedure
Step 1
The end device connects to the router through wired
and wireless connection. Enter the device domain name
(dahuawi.com) or device IP(default IP 192.168.10.110) to log in
to the device to congure settings.
Step 2
Step 3 Select the I have read and agree to the terms of the Software
Step 4
Step 5 Enter the login password, and then enter the web page.
Step 6
Step 7
.
Click OK
License Agreement and Privacy Policy checkbox, and then
click OK.
For the rst-time login,you need to set the login password,and then
click NEXT.
For the rst-time login,the device will pop up a setup wizard.
WAN settings: You can change the networking method (default
DHCP), click the icons to change, and then click Next.
Figure 3-6 WAN settings
●
If you can access Internet without any settings on your
bandwidth, select DHCP as the networking method.
●
If your bandwidth cannot obtain IP address automatically,
contact network administrator or bandwidth service provider,
select Static IP as the networking method, and then enter
related information as guided.
●
If you need to enter the account and password to access
Internet, select PPPoE as the networking method, and then enter
bandwidth account and bandwidth password.
Figure 3-7 Network settings
Step 8 Enter the WLAN Setting page, set Wi-Fi name, password and
power, and then click Save.
Figure 3-8 WLAN settings
Loading...