Daewoo RCU-3000 User Manual

Specifications
DAEWOO Electronics Multi Use Upright Series
Model
Rating
Watts
Weights(Net)
Dimension (LxWxH)
Cord Length
Inner Filter
R C U - 3 0 0 R
AC 220 V / 50 Hz
Max. 2000W
9.3 kg
1143 x 386 x 265 mm
HEPA Filter
( Gore Cleanstream )
Exhaust Filter
Head Light
Belt Agitator
HEPA Filter
GE(USA) 906 / AC 12V
Grand River(USA)
Components Desription & Assembling
A
Main Power Switch
DUST CUP
Nozzle Power Switch
HANDLE
( Grip + Pipe )
Pipe Extension Button
BODY
HOSE
Hose Clip
Height
djustment
Remove Button for Nozzle
PEDAL
BRUSH
Head Light
CREVICE
NOZZLE
NOZZLE
Cord Storage
DUSTING
BRUSH
Thermal Reset Button
Release Pedal
Cord Plug
UPHOLSTERY
NOZZLE
g
g
g
HOSE GUIDE & HOSE ASSEMBLING
HOSE GUIDE assemblin
- Set HOSE GUIDE on the top of the cleaner
- Screwing a screw with the "+" shape screw driver
HOSE AS assemblin
- Insert the body side of HOSE AS in the hose hole of the cleaner.
- Caution : Insert the protrusion of HOSE end
throu If connected the HOSE and the BODY,
The HOSE can not be removed from the BODY. If need the disassembling it, call the A/S center.
h "" mark in side of the hose hole
HOSE
Hose Guide
HANDLE ASSEMBLING NOZZLE ASSEMBLING
HANDLE assembling
- Insert HANDLE in the handle hole on the top of the Body as below the picture.
HANDLE disassembling
- Push the Handle Removal Button
- Pull HANDLE upward
HANDLE
Protrusion to lock
Handle Removal Button
NOZZLE assembling
- Set the main BODY on the top of the Body as below the picture.
- Use the both side of the guide feature on the NOZZLE.
BODY
NOZZLE disassembling
- Push the Nozzle Removal Button
- Lift up the BODY
Remove Button for Nozzle
NOZZLE
Using Guide & Converting to Canister Type
UPRIGHT USING STATE
Push the RELEASE PEDAL and rotate the BODY as below the picture.
- Set HOSE GUIDE on the top of the cleaner
- Causion : If the power switch is not ON, though the brush switch is ON the NOZZLE is not work. If this cleaner is not in the using state, though the power and the brush switch are ON,
the NOZZLE is not work because of the safty device(NOZZLE SAFTY SWITCH).
BODY
Nozzle Safty Switch
Release Pedal
NOZZLE
CONVERTING TO CANISTER TYPE
● Disassemble the NOZZLE and the HANDLE. ( See. Page 3 )
● Disassemble the Nozzle side of the HOSE end and connect it with HADLE as below
● Assemble the PEDAL BRUSH in the pipe end fo HADLE
● Extend the PIPE with the Pipe Extension Button for the convienient.
HANDLE
Pipe Extension Button
HOSE
PEDAL BRUSH
p
ACCESSORIES USING
To use all ACCESSORIES, Connect them to HOSE end.
- Causion : When use accessories, if air Inlet is narrow unexpectly,
HOSE length can be decreased and the cleaner can be come down.
NOZZLE HEIGHT CONTROL KEEPING
Rotate the HEIGHT ADJUSTMENT After com LEVER for the carpet surface to clean. keep in the state of UPRIGHT
To clean the bare floor, this LEVER set The Accessories are located the position of BARE FLOOR and set OFF in the storage hole of BODY the Nozzle Power Switch on the top of the cleaner(See-2page).
Height Adjustment Lever
● Roll the CORD CABLE at the Cord Storage in the side of BODY. and hang the Plug at the cord clip of HANDLE as the side view.
leting to use the cleaner,
Cord Clip
Plug
Cord Cable
p
p
g
p
Cleaning Dust Cup & Replacement Filters
DISASSEMBLING DUST CUP & EXHAUST FILTER
Set OFF the Cleaner.
Gras and pull out the DUST CUP from BODY.
Pull out the EXHAUST FILTER
the DUST CUP LEVER
EXHAUST
FILTER
BODY
Dust Cup Lever
DUST CUP
EMPTY DUST CUP
If dust filled u
or FULL CUP INDICATOR light on.
Move the DUST CUP at the
Push the DUST REMOVE BUTTON and the dust dro
at the height of the "FULL" line in the DUST CUP or FULL CUP LAMP light on.
arbage.
Dust Remove Button
automatically.
pping
(
)
)
X
INNER FILTER CLENING AND REPLACING
Lift up the DUST CUP COVER and rotate and remove the INNER FILTER
Ta
- Caution : This INNER FILTER is not washable. After tapping it, assemble it and use cleaner When tapping, be careful not to damage the filter media.
it to remove the dust at the pleats of it as below picture.
Replace the new INNER FILTER in every a year.
INNER FILTER TYPE No. : XXXXXX
Dust Cup Cover
Gore HEPA H-110 media
Inner Filter
EXHAUST FILTER CLEANING AND REPLACING
Disassemble the EXHAUST FILTER. ( See 6 page
If the EXHAUST FILTER become dirty. Replacing it.
- Caution : This INNER FILTER is not washable.
HEPA FILTER TYPE No. : XXXXX
HEPA FILTER
(
)
g
(
)
p
(
)
(
)
Replacing Belt & Nozzle Head Light
REPLACING BELT OF AGITATOR BRUSH
Turn OFF the cleaner.
Remove the BOTTOM PLAE of NOZZLE.
Set the new BELT over Motor Pully.
Han
Cover the BOTTOM PLATE and secure the 5 srcews
- Warnig : Before replacing the BELT. Check the disconnecting the cleaner from the electrical outlet.
the AGITATOR BRUSH into the BELT and assemble the AGITATOR BRUSH.
BELT TYPE No. : XXXXXX
unscrewing 5 screws with "+" shape screw driver.
Grand River, USA
REPLACING HEAD LIGHT ( only for RCU-3008F )
Turn OFF the cleaner.
Press the RELEASE PEDLA and
Remove the LENZ
Pull the BULB straight out of the SOCKET
Install the new BULB
Cover the LENZ and secure a screw.
BULB TYPE No. : XXXXXX
unscrewing a screws with "+" shape screw driver.
lace the HANDLE in the low position.
GE type No. GE906, 12 Volt
Lenz
Head Light
t
y
Please check each item below if you have trouble with your cleaner. Before checking, ensure that the cleaner is unplugged from the power supply.
NoteProblem Check Point
Cleaner won't run 1. Power cord not firmly plugged 1. Plug unit in firmly.
into outlet.
2. Motor protector tripped. 2. Cool down and press the RESET BUTTON ( See 2 page)
3. Need service. 3. Take to service center
or call XXXX-XXXX.
No power at rotating the AGITATOR 1. Cleaner is not the upright using sta
2. Brush Switch is OFF 2. Make sure Brush Switch is in ON.
3. Aigtator is stalled with cloth or etc. 3. Remove it.
4. Belt is broken or off motor pully. 4. Replace the new belt
Cleaner or Tool won't pick up dirt. 1. Incorrect Height Adjustment. 1. Rotate Height Adjustment Lever
2. Hose not attached to suction 2. Grasp hose tube and firmly push
opening. onto base.
3. Crack or hole in Hose 3. Take to service center
4. Dust Cup is full 4. Empty Dust Cup ( See 6 page )
1. Press the RELEASE PEDAL and Handle is angled. ( See 4 page )
or correct belt securing. ( See 8 page )
to correct height setting. ( See 5 page )
or call XXXX-XXXX.
If wash it, after dried well, re-insert it. Warning : Inner Filter not washable.
5. Inner Filter is cocked. 5. Clean it or replace new.
( See 7 page ) Warning : Inner Filter not washable.
Cleaner is difficult to push 1. Incorrect Height Adjustment 1. Rotate Height Adjustment Lever
to correct height setting. ( See 5 page )
Visible dust escaping from cleaner. 1. Dust Cup is full. 1. Empty Dust Cup ( See 6 page )
If wash it, after dried well, replace it
Warning : Inner Filter not washable.
2. Filter missing or installed incorrectl
3. Dust Cup installed incorrectly 3. Pull out and re-insert Dsut Cup
2. Check Inner Filter & Exhaust Filter for correct installation
correctly.
t
y
Trouble Shooting
Please check each item below if you have trouble with your cleaner. Before checking, ensure that the cleaner is unplugged from the power supply.
NoteProblem Check Point
Cleaner won't run 1. Power cord not firmly plugged 1. Plug unit in firmly.
into outlet.
2. Motor protector tripped. 2. Cool down and press the RESET BUTTON ( See 2 page)
3. Need service. 3. Take to service center
or call XXXX-XXXX.
No power at rotating the AGITATOR 1. Cleaner is not the upright using sta
2. Brush Switch is OFF 2. Make sure Brush Switch is in ON.
3. Aigtator is stalled with cloth or etc. 3. Remove it.
4. Belt is broken or off motor pully. 4. Replace the new belt
Cleaner or Tool won't pick up dirt. 1. Incorrect Height Adjustment. 1. Rotate Height Adjustment Lever
2. Hose not attached to suction 2. Grasp hose tube and firmly push
opening. onto base.
3. Crack or hole in Hose 3. Take to service center
4. Dust Cup is full 4. Empty Dust Cup ( See 6 page )
1. Press the RELEASE PEDAL and Handle is angled. ( See 4 page )
or correct belt securing. ( See 8 page )
to correct height setting. ( See 5 page )
or call XXXX-XXXX.
If wash it, after dried well, re-insert it. Warning : Inner Filter not washable.
5. Inner Filter is cocked. 5. Clean it or replace new.
( See 7 page ) Warning : Inner Filter not washable.
Cleaner is difficult to push 1. Incorrect Height Adjustment 1. Rotate Height Adjustment Lever
to correct height setting. ( See 5 page )
Visible dust escaping from cleaner. 1. Dust Cup is full. 1. Empty Dust Cup ( See 6 page )
If wash it, after dried well, replace it
Warning : Inner Filter not washable.
2. Filter missing or installed incorrectl
3. Dust Cup installed incorrectly 3. Pull out and re-insert Dsut Cup
2. Check Inner Filter & Exhaust Filter for correct installation
correctly.
Loading...