Daewoo PRD-233W User Manual
1 2
HERE ARE THE FEATURES OF YOUR NEW REFRIGERATOR
FEATURE CHART
2
5
4
3
6
8
9
10
11
12
1
13
14
18
19
16
17
7
15
! FREEZER TEMPERA TURE
CONTROL KNOB
@ F SHELF
# ICE HOLDER ASSEMBY
$ ICE CASE FRAME
ASSEMBY
% ICE BOX
^ CHILLED CORNER
& LAMP COVER
* REFRIGERA T OR
TEMPERA TURE CONTROL
( R SHELF
) CRISPER COVER
1 CRISPER
2 ADJUST ABLE POOT
3 F POCKET (SM)
4 F POCKET (SM)
5 EGG CASE
6 EGG POCKET
7 R POCKET (SM)
8 R POCKET (MEDIUM)
9 R POCKET (BG)
Take a moment to know all the features and convenience. Numbers
match those in the illustration on page 1.
■ Ice Tray: Fill tray 3/4 full to allow expansion of water during freezing. Place
tray in freezer chest. To release cubes, twist lid slightly .
■ Removable Shelf: Both shelves can be removed by pulling forward.
■ Crisper:
Use for fruit and vegetable storage. Both the crisper and its cover shelf
are removable for easy cleaning. Simply slide forward to remove.
■ Egg Pocket: Egg supporter in this pocket can be turned upside down.
Use for small size goods.
■ No Frost: No frost in freezing-room.
CAUTION
1.
Be sure to check with your voltage, before inserting the power supply cord into the socket.
2.
Contact the earthing conductor to this unit with an attachment earthing screws.
3. Don’t spill to this unit.
4. Don’t work with flammable spray , such as painting, near this unit.
5.
Don’t put ignitable materials, such as benzine, L .P . Gas, alcohol, etc., into this unit.
6. Be careful of the leakage of any gas equipment near this unit.
7. Be sure not to hold to the door of this unit by children.
8. Be sure not to reinsert the power supply , cord with 5 minutes after
releasing it from socket. If not, a trouble may be occurred to compressor .
RETURN-SPRING
STARTING POINT OF TWISTING
ICE CASE FRAME
ICE CASE
■ Ice Case Frame Assembly
1) Fill the ice case with water upto the water level line and insert it into the
designated space in the ice holder.
2)
After the water is completely frozen, twist the ice case handle clockwise and let the ice
fall into the ice box below. When all ice has been cleared from the ice case, let go of the
handle which will return to its original position by a return spring installed.
METHODS OF SAFE INSTALLATION
1. SAFE INST ALLATION PLACE FOR YOUR REFRIGERATOR
4
• Place the refrigerator on
hard and level floor.
NO
NO
• Place your refrigerator
where there is no heat
source nearby.
High surrounding
temperature will lower
cooling efficiency and
increases your electricity
bill.
• Place the refrigerator in
an area with low
moisture.
Splashing water or a
high moisture area may
cause a short circuit and
make rusting easier.
• Avoid places that are
exposed to smoke.
The discoloring can
occur to the refrigerator.
At least 15cm
At least 15cm
At least 30cm
Carpet
Wooden Board,
Rubber Mat
• For good ventilation
place refrigerator with
the space specified on
the figure.
This helps cooling
efficiency and lowers the
electricity bill.
• Placing the refrigerator
on the carpet may cause
heat to develop and
discolor the appliance. In
such a case put a hard
wooden board or a
rubber mat between the
refrigerator and the
carpet.
HOW TO OPERATE
1. TEMPERA TURE CONTROL
3
Temperature is controlled by thermostat automatically .
The Temperature Control inside the refrigerator controls the degree of
cooling for each compartment.
Freezer T emperature Control
The control has four settings from
MIN to WINTER. The WINTER
mode is available only if atmosphere
temperature is below 10°C.
Refrigerator T emperature Control
The control has four settings from MIN
to WINTER. The WINTER mode is
available only if atmosphere
temperature is below 10°C.
WINTER
MAX
MED
MIN
TEMP. CONTROL
WINTER
MAX
MED
MIN
TEMP. CONTROL
Starting your new refrigerator
To control temperature
Many factors may influence the internal temperature of the refrigerator
and freezer compartments.
■The temperature and humidity of the surrounding environment.
■The opening frequency of the doors and the amount of warm food placed in
the refrigerator.
■
The combination of food and containers stored in the refrigerator.
For these reasons, you may want to adjust the control to suit the season and your needs.
1. Clean the refrigerator thoroughly. Wipe the outside with a dry cloth, and the inside
with a damp cloth.
2. Set the temperature control knob at normal position.
3. Connect the power supply cord.
Check
• Check if the doors are
completely shut.
6
• Unplug the power cord.
Adhesive
Tape
• Fasten the interior
components with tape.
• Take food out of the
refrigerator
compartments.
• For relocating indoors
use the wheels.
Relocating
Indoors
Adhesive Tape
• When moving have two
people carry the
refrigerator for safety
• Fasten the doors with
tape while moving to
prevent them from
opening.
2. INST ALLATION STEPS
5
S
a
fe
in
s
ta
lla
tio
n
p
la
c
e
Maintain ~
Level
Components to their
original places
Check
Plug in after
about hour
P
u
t fo
o
d
a
fte
r
2
~
3
h
o
u
rs
• Level the refrigerator by
using the adjustable foot.
• Install the parts to their
own place.
3.
THINGS TO KNOW BEFORE MOVING OR RELOCA TING THE REFRIGERA TOR!
• Select a safe place to
install your refrigerator.
• After running the
refrigerator for 2 ~ 3
Hours put food in the
refrigerator.
• Check the voltage and
wait about an hour
before plugging the
power cord into an
outlet.
Loading...