Daewoo MON523X, MON432X Service Manual

Service Manual
XGA COLOR MONITOR Model : 432X / 523X
DAEWOO ELECTRONICS CO., LTD OVERSEAS SERVICE DEPT.
CONTENTS
SAFETY PRECAUTIONS 1 GENERAL SAFETY INFORMATION 2 SERVICING PRECAUTIONS 3 TECHNICAL INFORMATION 6 GENERAL INFORMATION 7 PIN CONNECTOR 8 CAUTIONS FOR ADJUSTMENT AND REPAIR 8 OPERATION AND ADJUSTMENT 9 ALIGNMENT PROCEDURE 12 TROUBLESHOOTING HINTS 14 BLOCK DIAGRAM 28 PCB LAYOUT 29 SCHEMATIC DIAGRAM 32 EXPLODED VIEW DIAGRAM 36 REPLACEMENT PARTS LIST 37 PARTS LIST 38
1
SAFETY PRECAUTIONS
Safety Check
Care should be taken while servicing this analog color display because of the high voltages used in the deflection circuits. These voltages are exposed in such areas as the associated flyback and yoke circuits.
Fire & Shock Hazard
• Insert an isolation transformer between the analog color display and AC power line before servicing chassis.
• In servicing, pay attention to original lead dress especially in the high voltage circuit. if a short circuit is found, replace all parts which have been overheated as a result of the short circuit.
• All the protective devices must be reinstalled per original design.
• Soldering must be inspected for possible cold solder points, frayed leads, damaged insulation, solder splashes or sharp solder points. Be certain to remove all foreign materials.
Implosion Protection
Picture tube in this monitor employs intergral implosion protection system, but care should be taken to avoid damage and scratching during installation. Use only same type replacement picture tubes.
X-Radiation
IMPORTANT SAFETY NOTICE: There are special components used in analog color display, which are
important for safety. These parts are shaded on the schematic diagram and on the replacement parts list. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X­radiation, shock, fire or other hazards. Do not modify the original design without getting a written permission from DAEWOO ELECTRONICS CO. or this will void the original parts and labor warranty.
CAUTION: No modifications of any circuit should be attempted. Service work should only be performed after
you are thoroughly familiar with all of the following safety check and servicing guidelines.
WARNING: The only potential source of X-Radiation is the picture tube. However when the high voltage
circuitry is operating properly, there is no possibility of an X-Radiation problem. The basic precaution which must be exercised is to keep the high voltage at the following factory recommended level.
NOTE: It is important to use an accurate, periodically calibrated high voltage meter.
• To measure the high voltage, use a high-impedance high-voltage meter. Connect(-) to chassis and (+) to the CRT anode button.
• Turn the Contrast & brightness control fully counterclockwise.
• Measure the high voltage. The high voltage meter should indicate the following factory
recommended level.
• If the upper meter indication exceeds the maximum level, immediate service is required to prevent
the possibility of premature component failure.
• To prevent X-Radiation possibility, it is essential to use the specified picture tube.
• The normal high voltage is 25.5KV or below, and must not exceed 29KV at zero beam current at
rated voltage.
2
Warning: This product includes critical mechanical and electrical parts which are essential for x radiation safety. For continued safety, replace critical components indicated in the service manual only with exact replacement parts given in the parts list. Operating high voltage for this product is 25Kv at minimum brightness. Refer to service manual for measurement procedures and proper service adjustments.
GENERAL SAFETY INFORMATION
Terms in the manual
CAUTION Statements identify conditions or practices that could result in damage to the equipment or other
property.
WARNING Statements identify conditions or practices that could result in personal injury or loss of life.
Terms as marked on equipment
CAUTION Statements indicate a personal injury hazard not immediately accessible as one reads the
marking, or a hazard to properly including the equipment itself.
WARNING Statements indicate a personal injury hazard immediately accessible as one reads the
marking
Symbols in the manual
This symbol indicates where applicable cautionary or other information is to be found.
Symbols as marked on equipment
Protective GROUND terminal
High Voltage W arning And Critical Component Warning Label
Following warning label is on the CRT PWB shield case inside the unit.
3
SERVICING PRECAUTIONS
General Servicing Precautions
1. Always unplug the AC power cord from the AC power source before: a. Removing or reinstalling any component, circuit board, module, or any other instrument assembly.
b. Disconnecting or reconnecting any electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the instrument.
d. Discharging the picture tube anode.
2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM. etc.) equipped with a suitable high voltage probe. Do not test high voltage by “drawing an arc”.
3. Discharge the picture tube anode only by: (a) first connecting one end of an insulated clip lead to the degaussing or line grounding system shield at the point where the picture tube socket ground lead is connected, and then (b) touching the other end of the insulated clip lead to the picture tube anode button, using an insulating handle to avoid personal contact with high voltage.
4. Do not any spray chemicals on or near this instrument or any or its assemblies.
5. Unless specified otherwise in this service manual, clean electrical contacts by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator: 10% (by volume) Aceton and 90% (by volume) isopropyl alchohol (90%-99% strength).
6. Do not defeat any plug/socket B+ voltage interlocks with which instruments covered by this service manual might be equipped.
7. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed.
8. Always connect the test instrument ground lead to the appropriate instrument chassis ground before connecting the test instrument positive lead. Always remove the test instrument ground lead last.
9. Use only the test fixtures specified in this service manual with this instrument.
CAUTION: Before servicing instruments covered by this service manual, its supplements and addendum,
read and follow the SAFETY PRECAUTIONS of this manual.
NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of
the safety precautions on page 1 of this manual, always follow the safety precautions. Remember: Safety First.
CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may
result in a explosion hazard.
CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication
of contacts is not required.
CAUTION: Do not connect the test fixture ground strap to any heatsink in this instrument.
4
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. The examples of typical ES devices are integrated circuits, some field-effect transistors and semiconductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static type solder removal device. Some solder removal devices not classified as “anti­static” can generate enough electrical charges to damage ES devices.
5.
Do not use freon-propelled chemicals. These can generate enough electrical charges to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmful motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate enough static electricity to damage an ES devices).
General Soldering Guidelines
1. Use a grounded-tip, low-wattage soldering iron with appropriate tip size and shape that will maintain tip temperature within a 550°F-660°F (288°C-316°C) range.
2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead.
3. Keep the soldering iron tip clean.
4. Throughly clean the surface to be soldered. Use a small wire-bristle (0.5 inch or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners.
5. Use the following soldering technique: a. Allow the soldering iron tip to reach normal temperature (550°F to 660°F or 288°C to 316°C) b. Hold the soldering iron tip and solder strand against the component lead until the solder melts. c. quickly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and
hold it there only until the solder flows onto and around both the component lead and the foil.
d.
Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush.
CAUTION:
Be sure that no power is applied to the chassis or circuit, and observe all other safety precautions.
CAUTION: Work quickly to avoid overheating the circuit board printed foil.
5
FIGURE 1. USE SOLDERING IRON TO PRY LEADS
IC Removal/Replacement
Some utilized chassis circuit boards have slotted (oblong) holes through which the IC leads are inserted and then bent flat against the circuit foil. When holes are slotted, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in paragraphs 5 on the page under the title of general soldering guidelines.
Removal
1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts.
2. Draw away the melted solder with an anti-static suction-type solder removal device (or with desoldering braid before removing the IC.
Replacement
1. Carefully insert the replacement IC in the circuit board.
2. Carefully bend each IC lead against the circuit foil pad and solder it.
3. Clean the soldered areas with a small wire-bristle brush. (lt is not necessary to reapply acrylic coating to the area).
“Small-Signal” Discrete T ransistor Removal/Replacement
1. Remove the defective transistor by clipping its leads as close as possible to the component body.
2. Bend the end of each of three leads remaining on the circuit board into a “U” shape.
3. Bend the replacement transistor leads into a “U” shape.
4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the “U” with long nose pliers to insoure metal-to-metal contact, then solder each connection.
6
Power IC, T ransistor or Devices Removal/Replacement
1. Heat and remove all solders from the device leads.
2. Remove the heatsink mounting screw (if applicable).
3. Carefully remove the device from the circuit board.
4. Insert new device in circuit board.
5. Solder each device lead, and clip off excess lead.
6. Replace heatsink.
Diode Removal/Replacement
1. Remove defective diode by clipping its leads as close as possible to diode body.
2. Bend the two remaining leads perpendicularly to the circuit board.
3. Observing diode polarity, wrap each lead out of the new diode around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect the solder joints of the two “original” leads on the circuit board copper side. If they are not shiny, reheat them and apply additional solder if necessary.
TECHNICAL INFORMATION
Electrical
CRT dot pitch 0.28mm dot pitch Horizontal frequency 30KHz to 54KHz(Automatically) Vertical fequency 50Hz to 120Hz (Automatically) Operating temperature 10-40°C / 50-104°F Operating humidity 8-80%
Mechanical
Cabinet Molded Plastic Cabinet with detachable tilt & swivel base Dimension (set with stand) 381(H) x 366(W) x 400(D) mm Weight(net) 12.1 Kg Controls Power Switch
OSD control
Contrast Brightness Horizontal Position Horizontal Size Vertical Position Vertical Size Pincushion Trapezoid R Gain, B Gain Color Temp Recall Degauss Status 5 Languages Self Diagnosis (Color bar pattern)
7
GENERAL INFORMATION
This color monitor automatically scans all horizontal frequencies from 30KHz to 54KHz, and all vertical frequencies from 50Hz to 120Hz. This color monitor supports IBM PC, PC/XT, PC/AT, personal System/2 (PS/2), Apple Macintosh, and compatible users crisp text and vivid color graphics display when using the following graphics adapters : (VGA, 8514/A, Super VGA, VESA and XGA and Apple Macintosh Video Card). And so, this color monitor has a maximum horizontal resolution of 1024 dots and a maximum vertical resolution of 768 lines for superior clarity of display. By accepting analog signal inputs which level is zero to 0.7 Volts. This color monitor can display and unlimited palette of colors depending on the graphics adapter and software being used.
Abbreviations
ADJ Adjustment AFC Automatic Frequency Control CRT Cathode Ray Tube Def Deflection D.Y Deflection Yoke FBT Flyback Transformer H.SYNC Horizontal Synchronization OSC Oscillator P.S.U Power Supply Unit PWA Printed Circuit Board Wiring Assembly R.G.B Red, Green, Blue V.Sync Vertical Synchronization
8
• Degaussing is always required when adjusting purity or convergence.
• The white balance adjustment has been done by a color analyzer in factroy. The adjustment procedure, described in the service manual is made by a visual check.
• Allow 20 minutes warm-up time for the display before checking or adjusting only electrical specification or function.
• Reform the leadwire after any repair work.
Caution For Servicing
In case of servicing or replacing CRT, high voltage sometimes remains in the anode of the CRT. Completely discharge high
voltage before servicing or replacing CRT to prevent a shock to the serviceman.
Arrangement of 15-pin D-sub connector
PIN CONNECTOR
Pin Signal
1 Red 2 Green 3 Blue 4 GND 5 GND 6 GND - Red 7 GND - Green 8 GND - Blue 9 +5Vdc 10 GND - H.Sync 11 GND - V.Sync 12 Bi-directional Data (SDA) 13 Horizontal Sync 14 Vertical Sync (VCLK) 15 Data Clock (SCL)
CAUTIONS FOR ADJUSTMENT AND REP AIR
1
6
10
15
9
OPERATION AND ADJUSTMENT
Control Panel
Move cursor to the right window on the OSD window.
Increase the value of any selected function.
Move cursor to the left window on the OSD window.
Decrease the value of any selected function.
Launch OSD(On-Screen Display) MENU window.
Move cursor to the high window on the OSD window.
Increase the value of V.size or V.center.
Move cursor to the low window on the OSD window.
Decrease the value of V.size or V.center.
10
Key Process
MENU
Start
When you choose the icon on the OSD window, you can exit the OSD screen.
Hot Key
BRIGHTNESS CONTRAST
11
ICON CONTROL FUNCTIONS
Adjust the width (horizontal size) and the height (vertical size) of the display.
Display horizontal & vertical frequency and polarity.
Degaussing keeps the monitor free from unwanted magnetism that can result in color impurity.
H. SIZE & V. SIZE
DEGAUSS
STATUS
Select language for OSD (5 languages).
Reset the screen to the Factory Preset Display Settings.
LANGUAGE
RECALL
OSD Functions
Adjust the left and right margins for more convex or more concave margins.
Adjust the trapezoid of the screen by moving the lines inward or outward.
PINCUSHION
TRAPEZOID
Choose different preset color temperatures or set your own customized color parameters.
Adjust the red gain.
Adjust the position of the display horizontally (left or right) and vertically (up or down).
H. CENTER & V. CENTER
COLOR TEMP
RED GAIN
Adjust the blue gain.
BLUE GAIN
Adjust the rotation when the screen is tilted left or right (Optional).
ROTATION
12
ALIGNMENT PROCEDURE
Standard Adjustment Conditions
1. Power source voltage: 100-240Vac 50/60Hz
2. Aging: Take at least 20 minutes warm-up time.
3. Signals Video:Analog 0.7Vpp 75terminal positive polarity Synchronizing:TTL level Negative/Positive Separate Deflection frequency
Horizontal Frequency : 30KHz - 54KHz Vertical Frequency : 50Hz - 120Hz
Pre-Adjustment
1. B+ Adjustment
Adjust 165Vdc ± 0.5Vdc between P008 and ground at 31.5KHz mode, varying VR101. Adjust 27.5Vdc ± 0.2Vdc between P009 and ground at 31.5KHz mode, varying VR501.
Main Adjustment
1. Setting the Controls Set the value of items as following.
Contrast:Max.(OSD value up to MAX) Brightness:Center(Set the OSD value to center)
2. H.size, V.size, H.phase, V.position, Pincushion, Trapezoid Receive the cross hatch pattern of Factory preset mode. H.size, V.size, H.phase, V.position, Pincushion, Trapezoid are adjusted at each mode. In Factory, Auto Alignment was done at each mode. Therefore, Factory preset mode has it’s own value according to each control.
3. Focus (a) Set brightness control to center and contrast control to MAX. (b) Receive all “H” character pattern of 1024 X 768 (48KHz, 60Hz) (c) Adjust the Focus control of FBT to obtain best Focus.
4. Geometric Distortion Adjustment. (a) Receive the cross hatch pattern of factory preset mode. (b) Pincushion, Trapezoid are adjusted the best geometric status.
5. White Balance Adjustment (a) Select 9300
°K on the OSD Menu.
(b) Receive a full white pattern of 54KHz mode signal by using the signal generator. (c) Set the brightness control to the maximum, the contrast control to the maximum. (d) Cut off the FBT screen VR. (e) Receive all the black patterns. The luminance of the screen should be 0.5~1.0 Ft-L by using Screen VR. (f) Select the R-BIAS, G-BIAS and B-BIAS on the control menu and adjust the DATA +/– key to get the color
coordinates in x=0.281 ± 0.015, y=0.311±0.015. (g) Receive a full white pattern. Adjust the brightness value to the center. (h) Select the R-GAIN and B-GAIN and adjust the DATA +/– key to get the color coordinates in x=0.281 ±
0.015, y=0.311 ± 0.015. (i) Adjust the sub contrast control to get the screen luminance to 30 Ft/L (a full white pattern over 30 Ft/L) (j) Check if the x, y coordinates of color analyzer is in x=0.281±0.015, y=0.311±0.015.
If the color coordinates is out of range, adjust the R. G. B BIAS & GAIN to get the coorinates in x=0.281, y=0.311. Make sure that the coordinates is in range.
(k) Select 6550
°K on the OSD Menu and set the color coordinates in x=0.313, y=0.329 at the maximum
contrast control and center brightness control
(l) Check if a full white pattern is over 30Ft/L.
13
6. Static Convergence Adjustment (a) Apply a magenta cross hatch pattern on display. (b) Adjust the focus from the best over all focus on the display.
Also adjust the brightness to the desired condition.
(c) Vertical red and blue lines are converged by varying the angle between the two tabs of the 4-pole
magnets.
(d) Horizontal red and blue lines are converged by varying the tabs together, keeping the angle between
them constant. (e) Apply a yellow cross hatch pattern on display. (f) Vertical green and red lines are converged by barying the angle between the two tabs of the 6-pole
magnets.
(g) Horizontal green and red lines are converged by varying the tabs together, keeping the angle between
them constant.
14
TROUBLESHOOTING HINTS
1. No Character
Are the Contrast &
Brightness Controls in
OSD menu
maximum?
Change the Contrast & Brightness control value to maximum
No Raster
Refer to No Raster
Check the peripheral circuit of CRT
Check the video output circuit and its ambient circuit
Trouble in 8Vdc line of the Main PWB
Check the clamping pulse circuit
Check the signal cable
No Character
Is whole
screen bright?
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
Yes
Yes
Rk, Gk, Bk
About 45Vpp
No
No
Is CRT
Cathode (Rk, Gk, Bk)
signal level
normal?
Is the
output signal of the
(pin 15, 19, 22) pre-amp
IC801, normal?
Is clamping
pulse (pin 23 of IC801)
normal?
Is 8Vdc line
normal?
Is input signal
normal?
Trouble in IC801 and
its ambient circuit
12Vpp
15
2. No Raster
Trouble in power supply circuit
Trouble in video circuit
Trouble in G1 line of Main PWB
Trouble in FBT
High Voltage trouble in FBT
Trouble in 65Vdc line of power supply unit
Refer to trouble in P.S.U
Refer to trouble in power supply unit.
Is CRT
heater red-hot?
No
Yes
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
No
Is Heater
Voltage (CRT PWB)
about 6V?
Increase the Brightness
& Contrast control level
fully Maximum
No Raster
Is whole
screen bright?
Check
G1 voltage about
-60V?
Is 65Vdc
line normal?
Does
increasing of the
Brightness control level
make screen
bright?
Is CRT
G2 (screen) voltage
about 650V?
Trouble in CRT
Raster OK
Yes
16
3. A Missing Color
Is input signal
normal?
One color is
missing
CRT
Cathode (Rk, Gk, Bk)
is normal?
Is video
output Q801, Q831, Q861
waveform normal?
Each grid (G1, G2)
voltage normal?
Is the
output of
pre-amp IC801
pin 15, 19, 22 all
normal?
Check video signal cable or video card.
Trouble in IC801 or its ambient circuit
Trouble in video output circuit, Q803, Q804 Q833, Q834 Q863, Q864 or ambient
Trouble in 65/8Vdc line
Trouble in G1 lind and G2 line
Replace CRT
No
No
No No
No
Yes
Yes
Yes
Yes
Yes
RK, GK, BK
About 45V p-p
0.7Vpp
17
4. Abnormal OSD Font
Is menu key
selected?
Is OSD Font
exist?
One color is
missing
Abnormal OSD Font
Is the
output of IC204
(PIN 21, 22, 23)
normal?
Refer to Missing Color
No
Yes
Yes
Yes
* If menu key selected.
Trouble in IC801 and its ambient circuit
No No
Yes
Is
the Fast Blanking signal (IC204 pin 20)
normal?
Trouble in IC204 or its ambient circuit
Trouble in IC204 and its ambient circuit
18
5. Horizontal Output Circuit
Is
B+ line boltage
normal?
Is
Q506 base
waveform
normal?
Trouble in power supply circuit
Refer to trouble in power supply unit
Trouble in FBT
Trouble in Horizontal
output circuit
(No Raster)
Yes
No
Q505 and its ambient cirucit
Trouble in Q505, T501
If the holddown circuit stops the horizontal oscillator during the check, turn off the power then turn on again about 10 seconds later
Yes
Yes
Yes
Check the circuit of P. S. U
No
Trouble in IC501
Yes
Trouble in H.sync line
11V p-p
12V p-p
14.5Vp-p
Yes
IS
Q505 Gate
waveform
normal?
Is
the input H.sync
correct?
Is
IC501 7pin
H.DRV waveform
normal?
Is
IC501 pin 9
voltage about
12V?
No
No
No
No
MODE B+ Voltage VGA 72Vdc Super VGA
86Vdc
54KHz 124Vdc
19
6. Unstable Picture
6-1. Horizontal
Unstable
picture
Is the
pulse of pin 15 of
the IC501
correct?
Trouble in IC501 or its ambient circuit
Is the
pulse of pin 33 of
the IC201
correct?
Check IC501 and its ambient circuit
No
No
No
Yes
Yes
Is the
input H.Sync
correct?
Check IC201 and its ambient circuit
Yes
Trouble in Signal Cable or 15P D-Sub Connector
5Vpp
20
6-2. V ertical
Unstable
picture
Is the
15Vdc
line voltage is
correct?
Refer to P. S. U
Is the
pulse of pin 4, 6 of
the IC401
correct?
Trouble in vertical D. Y
No
No
No
Yes
Yes
Is the output
of pin 12,13 of IC501
all normal?
Check IC401 and its ambient circuit
Yes
Check the IC501 and its ambient circuit
40Vp-p
21
7. Focus
Monitor remains
unfocused
Check
Focus VR in
FBT
Is
focus
acceptable?
Trouble in Focus
circuit (FBT)
Yes
OK
No
22
8. Convergence
Is
convergence
on the center area
bad?
Is
convergence on the
fringe area bad?
Adjust static convergence
Refer to Adjustment procedure of convergence
Yes
Adjust D.Y Location
Yes
No
Poor convergence
23
9. Abnormal Picture
9-1. Horizontal Size
Trouble in L503, C539 or their ambient circuit
Trouble in Horizontal output circuit Check the B+ and anode voltage of CRT.
Trouble in H.OSC/ Deflection Circuit
Refer to Horizontal Output circuit
Is
the DC level
of the base of Q521
changeable?
No
Yes
Is
the DC level
of C221
changeable ?
Yes
No
Check the Q519, Q520 and its ambient circuit
Is the
collector pulse
of Q506 correct?
Is the
cathode waveform
of D508 correct?
Check the IC201 and its ambient circuit
Abnormal
H.Size
=1100Vp-p
50-250Vpp
*
Normally anode voltage of CRT is approximately, 24KV
*
Scan B+ are as follow :
No
Yes
Yes
No
*
At first, adjust controls in the OSD Menu
MODE B+ Voltage VGA 72Vdc Super VGA
86Vdc
54KHz 124Vdc
24
9-2. V ertical Size
Is
the DC
voltage of C219
changeable ?
Check the IC201 and its ambient circuit
No
Trouble in Vertical Output Circuit
Refer to Vertical Output circuit
Yes
Abnormal
V.Size
25
10. Side-Pincushion Circuit
Check the Q518, Q522 and its ambient circuit
Yes
Pincusion distortion
is excessive or barrel
O.K
Select the
pincushion
icon in OSD menu,
and adjust acceptable
position.
Yes
Is the
waveform of IC501
(pin 11) correct?
No
No
Check the IC501 and
its ambient circuit
26
1 1. Power Supply Unit (P.S.U)
Is the
IC001
O.K?
Replace IC001
No
Is
voltage of C104
65Vdc?
No
Is
voltage of D002
130V (270V)?
Trouble in switching power transformer T001 or IC001 and its ambient circuit
Trouble in diode D001,D002,D003,D004 or peripheral device
No
Is the
waveform of T001
pin5 correct?
Trouble in T001 or D101
No
Trouble in P.S.U
Is
power switch
on?
Switch on
No
Yes
Yes
Yes
Yes
Yes
Yes
Is
voltage of C102
165Vdc?
Trouble in T001 or D102
No
Is
fuse F001
O.K?
Check the power cord outlet and diode D001,D002,D003,D004
No
A
27
A
Is voltage
of C108 35Vdc?
Yes
Is
voltage of IC103
pin3 12Vdc?
Yes
Is voltage
of IC102 pin 3
5Vdc?
Yes
P.S.U O.K
No
No
No
Trouble in D104, T001
Trouble in D106, Q103, Q104, IC103
Trouble in IC102 D103
28
BLOCK DIAGRAM
R
G
B
R/G/B BIAS
FOCUS
SCREEN
ABL
H.V
MAIN B+
VIDEO B+
V-OUT B+
GENERAL
HEATER
(+165V)
(+65V)
(+35V)
(+15V)
(+8V)
DEGAUSS
SCL1
SDA1
SS1
V -O
S
V -I
S
H -I
S
S
MUTE
H -O
H/V SIZE
H/V POS
G/D
H-FBP
H-LIN
V-BLK
SCL
SDA
F-BLK
R/G/B OSD
DY
SIGNAL
IN
PRE AMP
MC13282EP
VIDEO OUT & BIAS
BFQ225, PH2369,
BFQ221, BFQ241
BRIGHT
CONTROL
EEPROM
24LC04B
MCU
NT6862
OSD GEN
DWOSD04
CONTRAST
& ABL
CONTROL
V -OUT
TDA4866
H-OUT
CHOPPER
FBT
POWER IN
& FILTER
CIRCUIT
H/V OSC, G/D
CHOPPER
CONTROL
TDA4858
SMPS
STR-F6653
D-COIL
R/B GAIN
CLAMP
CONTRAST
CONTRAST
BRIGHTNESS
PCB LAYOUT
29
Main PCB Component Side
30
Main PCB Solder Side
31
Video PCB Component Side
Video PCB Solder Side
32
SCHEMATIC DIAGRAM
333435
EXPLODED VIEW DIAGRAM
36
REPLACEMENT P A RTS LIST
37
RESISTOR Description
Example:
CAP ACITOR Description
Example:
Important Safety Notice
Components identified with the International Symbol have special characteristics important for safety. When replacing any components, use only manufacturer’s specified parts.
Abbreviation of Description
Fig &
Part No Description
Index R101
Resistors
RE-42820J Carbon: 82J
R102 RD-4Z201J Carbon1/4W-200J
Allowance F±1% J±5% K ± 10% M ± 20% G±2%
Allowance C ± 0.25pF D ± 0.5% F ± 1pF J±5% K ± 10% P ± 100% ~ 0% Z ± 80% ~ –
Fig &
Part No Description
Index
Capacitors C102 CCXF1H104Z Ceramic 50V 0.1µFZ
C402 CCXB1H331K Ceramic 50V 22PFK C105 CMXM 2A224J MYLAR 100V 0.22µFJ
38
0001 9979800483 PCB MAIN CMC-432X T=1.6*246*310 0001 9979800484 PCB CRT CMC-432X T=1.6*136*105 B001 5PB13890-- COIL BEAD BI3890 B002 5PB13890-- COIL BEAD BI3890 B003 5PB13857-- COIL BEAD BI3857(AXIAL) B004 5PB13857-- COIL BEAD BI3857(AXIAL) B005 5PB13857-- COIL BEAD BI3857(AXIAL) B006 5PB13857-- COIL BEAD BI3857(AXIAL) B007 5PB13857-- COIL BEAD BI3857(AXIAL) B201 5PB13857-- COIL BEAD BI3857(AXIAL) B203 5PB13857-- COIL BEAD BI3857(AXIAL) B501 5PB13890-- COIL BEAD BI3890 B502 5PB13857-- COIL BEAD BI3857(AXIAL) B503 5PB13857-- COIL BEAD BI3857(AXIAL) B504 5PB13857-- COIL BEAD BI3857(AXIAL) B505 5PB13857-- COIL BEAD BI3857(AXIAL) B506 5PB13857-- COIL BEAD BI3857(AXIAL) B890 5PB13857-- COIL BEAD BI3857(AXIAL) B892 5PB13857-- COIL BEAD BI3857(AXIAL) C001 CL1UC3104M C LINE ACROSS WORLD AC250V 0.1UF M R.47 C002 CEYP2G221Z C ELECTRO 400V SMH 220MF (25.4*40) C003 CCXE3D103P C CERA HIKE 2KV 0.01MF P C004 CCXB3A101K C CERA 1KV B 100PF K C005 CEXF1H470C C ELECTRO 50V RUS 47MF (6.3X11) TP C006 CCXB1H681K C CERA 50V B 680PF K (TAPPING) C007 CMXM2A152J C MYLAR 100V 1500PF J (TP) C008 CH1FDF222M C CERA AC HIKB AC400V 222M C009 CH1FDF222M C CERA AC HIKB AC400V 222M C102 CEXF2C470V C ELECTRO 160V RSS 47MF (13X25) TP C104 CEXF2A101V C ELECTRO 100V RSS 100MF (13X20) TP C105 CEXF1C471V C ELECTRO 16V RSS 470MF (10X12.5)TP C106 CEXF1C470V C ELECTRO 16V RSS 47MF (5X11) TP C107 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C108 CEXF1H221C C ELECTRO 50V RUS 220MF (10X16) TP C109 CEXF1C471C C ELECTRO 16V RUS 470MF (10X12.5)TP C111 CEXF1C102V C ELECTRO 16V RSS 1000MF (10X20) TP C112 CEXF1E102D C ELECTRO 25V RMU 1000MF (10*20) C113 CEXF1C471V C ELECTRO 16V RSS 470MF (10X12.5)TP C115 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C118 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C120 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C121 CMXM2A102J C MYLAR 100V 1000PF J (TP) C122 CEXF1H109V C ELECTRO 50V RSS 1MF (5X11) TP C202 CCXB1H102K C CERA 50V B 1000PF K (TAPPING) C203 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C204 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C205 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C208 CCXB1H102K C CERA 50V B 1000PF K (TAPPING) C209 CCXB1H102K C CERA 50V B 1000PF K (TAPPING) C210 CCXB1H181K C CERA 50V B 180PF K (TAPPING) C211 CCXB1H181K C CERA 50V B 180PF K (TAPPING)
LOC PART-CODE PART-NAME PART-DESC
C214 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C215 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C216 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP C217 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP C218 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP C219 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP C220 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP C221 CEXF1H229V C ELECTRO 50V RSS 2.2MF (5X11) TP C223 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C224 CEXF1C101V C ELECTRO 16V RSS 100MF (6.3X11) TP C225 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C226 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C227 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C228 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C229 CCXB1H101K C CERA 50V B 100PF K (TAPPING) C230 CCXB1H101K C CERA 50V B 100PF K (TAPPING) C231 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C232 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C233 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C234 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C235 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C236 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C237 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C238 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C239 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C240 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C250 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C251 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C401 CMXM2A104J C MYLAR 100V 0.1MF J (TP) C402 CMXM2A104J C MYLAR 100V 0.1MF J (TP) C403 CMXM2A473J C MYLAR 100V 0.047MF J (TP) C404 CMXM2A473J C MYLAR 100V 0.047MF J (TP) C405 CEXF1E102D C ELECTRO 25V RMU 1000MF (10*20) C406 CMXM2A224J C MYLAR 100V 0.22MF J C407 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP C408 CCXB1H102K C CERA 50V B 1000PF K (TAPPING) C409 CMXL2E104J C MYLAR MEU 250V 0.1MF J C410 CCXB2H471K C CERA 500V B 470PF K (TAPPING) C501 CXCH1H470J C CERA 50V CH 47PF J (TAPPING) C502 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C503 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C504 CEXF1H220V C ELECTRO 50V RSS 22MF (5X11) TP C505 CMXM2A472G C MYLAR 100V 4700PF G (TP) C506 CEXF1C221V C ELECTRO 16V RSS 220MF (8X11.5) TP C507 CMXM2A123J C MYLAR 100V 0.012MF J (TP) C508 CCXB1H102K C CERA 50V B 1000PF K (TAPPING) C509 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C510 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C511 CMXM2A152J C MYLAR 100V 1500PF J (TP) C512 CMXM2A473J C MYLAR 100V 0.047MF J (TP) C513 CMXM2A103J C MYLAR 100V 0.01MF J (TP)
LOC PART-CODE PART-NAME PART-DESC
CIRCUIT BOARD ELECTRICAL P ARTS LIST
The components identified by mark ! have special characteristics important for safety and x-ray radiation. These should be replaced only with the types specified in the parts list.
! !
! !
39
C514 CMXM2A104J C MYLAR 100V 0.1MF J (TP) C515 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C516 CCXB2H102K C CERA 500V B 1000PF K (TAPPING) C517 CMXM2A104J C MYLAR 100V 0.1MF J (TP) C518 CEXF1H101V C ELECTRO 50V RSS 100MF (8X11.5) TP C519 CMXH3C602J C MYLAR BUP 1.6KV 6000PF J C520 CMXE2J822J C MYLAR PL 630V 8200PF J C521 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C522 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C523 CCXB3D101K C CERA 2KV B 100PF K (TAPPING) C524 CMXB2A472J C MYLAR 100V EU 4700PF J (TP) C527 CCXB3A102K C CERA 1KV B 1000PF K (TAPPING) C528 CMYF2G514J C MYLAR MPP 400V 0.51MF J BULK C529 CMYF2D514J C MYLAR 200V MPP 0.51MF J C530 CMXF2D224J C MYLAR MPP 200V 0.22MF J C531 CCXB2H102K C CERA 500V B 1000PF K (TAPPING) C532 CCXF1H104Z C CERA 50V F 0.1MF Z C533 CCXB2H102K C CERA 500V B 1000PF K (TAPPING) C534 CCXF1H104Z C CERA 50V F 0.1MF Z C535 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C536 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C537 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C538 CMXM2A152J C MYLAR 100V 1500PF J (TP) C539 CMYF2D165J C MYLAR MPP 200V 1.6MF J C560 CEXF2C479V C ELECTRO 160V RSS 4.7MF (8X16) TP C561 CEXF2V229V C ELECTRO 350V RSS 2.2MF(10*12.5) C580 CMXM2A682J C MYLAR 100V 6800PF J (TP) C590 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C591 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C592 CEXF1H479V C ELECTRO 50V RSS 4.7MF (5X11) TP C801 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C802 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C803 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C804 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C805 CEXF1H100V C ELECTRO 50V RSS 10MF (5X11) TP C807 CXCH1H220J C CERA 50V CH 22PF J (TAPPING) C808 CEXF2A100V C ELECTRO 100V RSS 10MF (6.3X11) TP C809 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C810 CEXF2A109V C ELECTRO 100V RSS 1MF (5*11) TP C811 CEXF2A109V C ELECTRO 100V RSS 1MF (5*11) TP C812 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C831 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C832 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C833 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C834 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C837 CXCH1H150J C CERA 50V CH 15PF J (TAPPING) C838 CEXF2A100V C ELECTRO 100V RSS 10MF (6.3X11) TP C839 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C840 CEXF2A109V C ELECTRO 100V RSS 1MF (5*11) TP C841 CEXF2A109V C ELECTRO 100V RSS 1MF (5*11) TP C842 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C861 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C862 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C863 CEXF1H339V C ELECTRO 50V RSS 3.3MF (5X11) TP C864 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012
LOC PART-CODE PART-NAME PART-DESC
C867 CXCH1H220J C CERA 50V CH 22PF J (TAPPING) C868 CEXF2A100V C ELECTRO 100V RSS 10MF (6.3X11) TP C869 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C870 CEXF2A109V C ELECTRO 100V RSS 1MF (5*11) TP C871 CEXF2A109V C ELECTRO 100V RSS 1MF (5*11) TP C872 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C890 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C891 CEXF1C470V C ELECTRO 16V RSS 47MF (5X11) TP C892 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C893 CEXF1C221V C ELECTRO 16V RSS 220MF (8X11.5) TP C895 CMXM2A103J C MYLAR 100V 0.01MF J (TP) C896 CCXB2H102K C CERA 500V B 1000PF K (TAPPING) C897 HCZK104ZCA C CHIP CERA 50V Z5U 0.1MF Z 2012 C898 CCXE3D103P C CERA HIKE 2KV 0.01MF P C899 CEXF1C470V C ELECTRO 16V RSS 47MF (5X11) TP CA202 99707C0009 CONN AS SMH250-12+51088-13=160 CA203 9970780030 CONN AS SMH250-8+51088-9=160 CA801 9970710206 CONN AS 35068-9812+4.3PIE=100 CA802 9970710207 CONN AS 35068+35072-9712=140 CDT 9979615003 CDT M36KXU110XX61(T) CG 9970710205 CRT GND AS 0.12*6*16+BL102NG=630 CG1 4859242220 CONN WAFER YFW800-02 CW201 485923272S CONN WAFER 5267-06A STICK TYPE CW801 9979220021 CONN WAFER SMAW250-06 (ANGLE) CW802 9979220027 CONN WAFER SMAW250-12 (ANGLE) CW803 9979220023 CONN WAFER SMAW250-08 (ANGLE) CW804 9979300002 SOCKET CRT ISHM10S D001 D2A05----- DIODE 2A05 D002 D2A05----- DIODE 2A05 D003 D2A05----- DIODE 2A05 D004 D2A05----- DIODE 2A05 D005 DRU1P----- DIODE RU 1P (TAPPING) D006 DRGP10D--- DIODE RGP 10-D (TAPPING) D007 DZN4148--- DIODE 1N4148 AUTO 52MM D008 DZN4148--- DIODE 1N4148 AUTO 52MM D101 DRU3C----- DIODE RU 3C D102 DS2L60---R DIODE S2L60 D103 DD1NL20U-- DIODE D1NL20U D104 DD1NL40--- DIODE D1NL40 D105 DZN4148--- DIODE 1N4148 AUTO 52MM D106 DD2L20U--- DIODE D2L20U D109 DZN4148--- DIODE 1N4148 AUTO 52MM D207 DZN4148--- DIODE 1N4148 AUTO 52MM D208 DZN4148--- DIODE 1N4148 AUTO 52MM D209 DZN4148--- DIODE 1N4148 AUTO 52MM D210 DZN4148--- DIODE 1N4148 AUTO 52MM D211 D1NS4----- DIODE 1NS4 D401 D1N4002A-- DIODE 1N4002 D402 D1N4002A-- DIODE 1N4002 D403 DZN4148--- DIODE 1N4148 AUTO 52MM D501 DRGP10D--- DIODE RGP 10-D (TAPPING) D503 DZN4148--- DIODE 1N4148 AUTO 52MM D505 DZN4148--- DIODE 1N4148 AUTO 52MM D506 D1N4002A-- DIODE 1N4002 D507 DZN4148--- DIODE 1N4148 AUTO 52MM
LOC PART-CODE PART-NAME PART-DESC
!
! ! !
!
F001A 9977410900 FUSE CLIP BSP3-H T0.4 SN 5.2 F001B 9977410900 FUSE CLIP BSP3-H T0.4 SN 5.2 IC001 1STRF6653- IC POWER STR-F6653 IC101 1KA431ZTA- IC SHUNT KA431ZTA IC102 1XC62A500- IC REGULATOR XC62AP5002TH IC103 1K1A7812P1 IC REGULATOR KIA7812PI IC201 1DWM240T-- IC MICOM NT68P62 IC202 1M24C04BN6 IC EEPROM M24C04-BN6 IC203 1KA7542--- IC VOTAGE DETECTOR KA7542 IC204 1DW0SD03-- IC OSD DWOSD03 IC401 1TDA4866-- IC V-OUT TDA4866 IC501 1TDA4858-- IC H-OSC TDA4858 IC801 1MC13282EP IC VIDEO PREAMP MC13282EP L501 5CPZ568K03 COIL PEAKING 0.56UH K (AXIAL 7MM) L502 5MH0000064 COIL H-LINEARITY TRL-523X L503 5MC0000060 COIL CHOKE TCH-18A L801 5CPZ279K03 COIL PEAKING 2.7UH K (AXIAL 7MM) L802 5CPZ478K03 COIL PEAKING 0.47UH K (AXIAL 7MM) L831 5CPZ279K03 COIL PEAKING 2.7UH K (AXIAL 7MM) L832 5CPZ398K03 COIL PEAKING 0.39UH K (AXIAL 7MM) L861 5CPZ229K03 COIL PEAKING 2.2UH K (AXIAL 7MM) L862 5CPZ398K03 COIL PEAKING 0.39UH K (AXIAL 7MM) L891 5CPZ101K04 COIL PEAKING 100UH K (AXIAL 10.5MM) P001 9979500012 RECEPTACLE 02ME4E1/FILTER EMI P002 9977410800 TERMINAL PIN BSP1(SN) L=15MM P003 9977410800 TERMINAL PIN BSP1(SN) L=15MM P004 9977410800 TERMINAL PIN BSP1(SN) L=15MM P005 9977410800 TERMINAL PIN BSP1(SN) L=15MM P006 9977410800 TERMINAL PIN BSP1(SN) L=15MM P007 9977410800 TERMINAL PIN BSP1(SN) L=15MM P008 9977410800 TERMINAL PIN BSP1(SN) L=15MM P009 9977410800 TERMINAL PIN BSP1(SN) L=15MM P010 9977410800 TERMINAL PIN BSP1(SN) L=15MM PA001 W1173D831- CORD POWER SP30+IS14(I) PH001 1TLP721GR- IC PHOTO COUPLER TLP721D4GR Q101 TKTA1273Y- TR KTA1273-Y Q102 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q103 TKTA1273Y- TR KTA1273-Y Q104 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q105 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q202 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q203 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q204 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q205 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q401 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q501 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q502 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q503 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q504 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q505 TBSN254A-- FET BSN254A Q506 TBU2520DX- TR BU2520DX Q507 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q508 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q509 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q510 T1RF630A-- FET IRF630A
LOC PART-CODE PART-NAME PART-DESC
D508 DFMP2FUR-- DIODE FMP-2FUR D509 DZN4148--- DIODE 1N4148 AUTO 52MM D510 DD1NL20U-- DIODE D1NL20U D511 DZN4148--- DIODE 1N4148 AUTO 52MM D512 DZN4148--- DIODE 1N4148 AUTO 52MM D513 DZN4148--- DIODE 1N4148 AUTO 52MM D518 DZN4148--- DIODE 1N4148 AUTO 52MM D519 DZN4148--- DIODE 1N4148 AUTO 52MM D520 DZN4148--- DIODE 1N4148 AUTO 52MM D560 DRGP10D--- DIODE RGP 10-D (TAPPING) D561 D1N4002A-- DIODE 1N4002 D562 D1N4004--- DIODE 1N4004 D564 DZN4148--- DIODE 1N4148 AUTO 52MM D565 DZN4148--- DIODE 1N4148 AUTO 52MM D566 DZN4148--- DIODE 1N4148 AUTO 52MM D567 DZN4148--- DIODE 1N4148 AUTO 52MM D568 DZN4148--- DIODE 1N4148 AUTO 52MM D569 DZN4148--- DIODE 1N4148 AUTO 52MM D580 DZN4148--- DIODE 1N4148 AUTO 52MM D581 DZN4148--- DIODE 1N4148 AUTO 52MM D582 DZN4148--- DIODE 1N4148 AUTO 52MM D590 DZN4148--- DIODE 1N4148 AUTO 52MM D801 DZN4148--- DIODE 1N4148 AUTO 52MM D802 DZN4148--- DIODE 1N4148 AUTO 52MM D803 DZN4148--- DIODE 1N4148 AUTO 52MM D804 DZN4148--- DIODE 1N4148 AUTO 52MM D805 DZN4148--- DIODE 1N4148 AUTO 52MM D806 DZN4148--- DIODE 1N4148 AUTO 52MM D831 DZN4148--- DIODE 1N4148 AUTO 52MM D832 DZN4148--- DIODE 1N4148 AUTO 52MM D833 DZN4148--- DIODE 1N4148 AUTO 52MM D834 DZN4148--- DIODE 1N4148 AUTO 52MM D835 DZN4148--- DIODE 1N4148 AUTO 52MM D836 DZN4148--- DIODE 1N4148 AUTO 52MM D861 DZN4148--- DIODE 1N4148 AUTO 52MM D862 DZN4148--- DIODE 1N4148 AUTO 52MM D863 DZN4148--- DIODE 1N4148 AUTO 52MM D864 DZN4148--- DIODE 1N4148 AUTO 52MM D865 DZN4148--- DIODE 1N4148 AUTO 52MM D866 DZN4148--- DIODE 1N4148 AUTO 52MM D890 DZN4148--- DIODE 1N4148 AUTO 52MM DG 5MG0000056 COIL DEGAUSSING DG-1512BA DL211 DSD50GYW-- LED SD50GYW(GREEN/AMBER) DZ109 DDZ8R2BM-- DIODE ZENER DZ8.2BM DZ201 DDZ5R1B--- DIODE ZENER DZ-5.1B DZ202 DDZ5R1B--- DIODE ZENER DZ-5.1B DZ203 DDZ5R1B--- DIODE ZENER DZ-5.1B DZ204 DDZ5R1B--- DIODE ZENER DZ-5.1B DZ205 DDZ5R1B--- DIODE ZENER DZ-5.1B DZ206 DDZ5R1B--- DIODE ZENER DZ-5.1B DZ516 DDZ15BM--- DIODE ZENER DZ15BM DZ517 DDZ15BM--- DIODE ZENER DZ15BM DZ563 DDZ5R1B--- DIODE ZENER DZ-5.1B DZ580 DDZ10BM--- DIODE ZENER DZ10BM F001 5F3CB3122L FUSE CERA SEMKO TL 3.15AH 250V MF51
LOC PART-CODE PART-NAME PART-DESC
40
!
!
!
!
!
R111 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R112 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R120 RN-AZ1503F R METAL FILM 1/6 150K OHM F R121 RN-AZ2201F R METAL FILM 1/6 2.2K OHM F R122 HRFT204JCA R CHIP 1/10 200K OHM J 2012 R123 RD-AZ562J- R CARBON FILM 1/6 5.6K OHM J R124 HRFT152JCA R CHIP 1/10 1.5K OHM J 2012 R127 RD-AZ622J- R CARBON FILM 1/6 6.2K OHM J R128 HRFT472JCA R CHIP 1/10 4.7K OHM J 2012 R129 RD-AZ563J- R CARBON FILM 1/6 56K OHM J R202 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R203 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R204 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R205 HRFT393JCA R CHIP 1/10 39K OHM J 2012 R207 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 R208 HRFT105JCA R CHIP 1/10 1M OHM J 2012 R209 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 R210 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 R211 RN-AZ1502F R METAL FILM 1/6 15K OHM F R212 RN-AZ4322F R METAL FILM 1/6 43.2K OHM F R213 RN-AZ2002F R METAL FILM 1/6 20.0K OHM F R214 RN-AZ1002F R METAL FILM 1/6 10K OHM F R215 RN-AZ1502F R METAL FILM 1/6 15K OHM F R216 RN-AZ4322F R METAL FILM 1/6 43.2K OHM F R217 RN-AZ2002F R METAL FILM 1/6 20.0K OHM F R218 RD-AZ202J- R CARBON FILM 1/6 2K OHM J R219 RD-AZ222J- R CARBON FILM 1/6 2.2K OHM J R220 RD-AZ201J- R CARBON FILM 1/6 200 OHM J R221 RD-AZ222J- R CARBON FILM 1/6 2.2K OHM J R222 RD-AZ201J- R CARBON FILM 1/6 200 OHM J R223 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R224 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R225 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R226 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R231 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R232 RD-AZ752J- R CARBON FILM 1/6 7.5K OHM J R233 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R234 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R235 HRFT472JCA R CHIP 1/10 4.7K OHM J 2012 R236 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R237 HRFT472JCA R CHIP 1/10 4.7K OHM J 2012 R238 RD-AZ243J- R CARBON FILM 1/6 24K OHM J R239 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R240 RD-AZ303J- R CARBON FILM 1/6 30K OHM J R241 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R242 RD-AZ203J- R CARBON FILM 1/6 20K OHM J R243 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R244 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J R245 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R247 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R250 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R251 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R252 RD-AZ151J- R CARBON FILM 1/6 150 OHM J R253 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 R254 HRFT123JCA R CHIP 1/10 12K OHM J 2012
LOC PART-CODE PART-NAME PART-DESC
Q511 TKTC3200Y- TR KTC3200Y Q512 T1RF630A-- FET IRF630A Q513 TKTC3200Y- TR KTC3200Y Q514 T1RF630A-- FET IRF630A Q517 TZTC3202Y- TR KTC3202Y (AUTO)(1959Y) Q518 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q519 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q520 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q521 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q522 TBD677A--- TR BD677A Q523 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q524 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q525 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q526 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q560 TZTC3207-- TR KTC3207 (AUTO) Q561 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q562 TKTA1277Y- TR KTA1277Y Q580 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q581 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q582 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q583 TZTC3207-- TR KTC3207 (AUTO) Q590 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q592 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q593 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q594 TZTA1266Y- TR KTA1266Y- (AUTO)(1015Y) Q801 TBFQ225--- TR BFQ225 Q802 TPH2369--- TR PH2369 Q803 TBFQ221--- TR BFQ221 Q804 TBFQ241--- TR BFQ241 Q805 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q806 TKTC3200Y- TR KTC3200Y Q831 TBFQ225--- TR BFQ225 Q832 TPH2369--- TR PH2369 Q833 TBFQ221--- TR BFQ221 Q834 TBFQ241--- TR BFQ241 Q835 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q836 TKTC3200Y- TR KTC3200Y Q861 TBFQ225--- TR BFQ225 Q862 TPH2369--- TR PH2369 Q863 TBFQ221--- TR BFQ221 Q864 TBFQ241--- TR BFQ241 Q865 TZTC3198Y- TR KTC3198Y-(1815Y) (AUTO) Q866 TKTC3200Y- TR KTC3200Y R001 RD-2Z105J- R CARBON FILM 1/2 1M OHM J R002 RD-2Z124J- R CARBON FILM 1/2 120K OHM J R003 RS02Z273J- R M-OXIDE FILM 2W 27K OHM J (TAPPING) R005 HRFT681JCA R CHIP 1/10 680 OHM J 2012 R006 RD-AZ332J- R CARBON FILM 1/6 3.3K OHM J R007 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R009 RW01Z158JN R WIRE WOUND 1W 0.15 OHM J NON-INDUCT R104 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R105 RD-4Z331J- R CARBON FILM 1/4 330 OHM J R107 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R108 RD-4Z122J- R CARBON FILM 1/4 1.2K OHM J R109 RS01Z330J- R M-OXIDE FILM 1W 33 OHM J (TAPPING)
LOC PART-CODE PART-NAME PART-DESC
41
R511 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R512 HRFT393JCA R CHIP 1/10 39K OHM J 2012 R513 HRFT222JCA R CHIP 1/10 2.2K OHM J 2012 R514 RD-AZ122J- R CARBON FILM 1/6 1.2K OHM J R515 RD-AZ362J- R CARBON FILM 1/6 3.6K OHM J R516 HRFT273JCA R CHIP 1/10 27K OHM J 2012 R517 RD-AZ474J- R CARBON FILM 1/6 470K OHM J R518 HRFT184JCA R CHIP 1/10 180K OHM J 2012 R519 RD-AZ204J- R CARBON FILM 1/6 200K OHM J R520 HRFT102JCA R CHIP 1/10 1K OHM J 2012 R521 RD-AZ220J- R CARBON FILM 1/6 22 OHM J R522 HRFT243JCA R CHIP 1/10 24K OHM J 2012 R523 RD-2Z221J- R CARBON FILM 1/2 220 OHM J R524 RS02Z820J- R M-OXIDE FILM 2W 82 OHM J (TAPPING) R525 RS02Z820J- R M-OXIDE FILM 2W 82 OHM J (TAPPING) R526 HRFT222JCA R CHIP 1/10 2.2K OHM J 2012 R527 HRFT102JCA R CHIP 1/10 1K OHM J 2012 R528 HRFT682JCA R CHIP 1/10 6.8K OHM J 2012 R529 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 R530 HRFT270JCA R CHIP 1/10 27 OHM J 2012 R531 RS01Z331J- R M-OXIDE FILM 1W 330 OHM J (TAPPING) R533 RD-AZ223J- R CARBON FILM 1/6 22K OHM J R534 RD-4Z104J- R CARBON FILM 1/4 100K OHM J R535 RD-4Z104J- R CARBON FILM 1/4 100K OHM J R536 RD-AZ223J- R CARBON FILM 1/6 22K OHM J R537 RD-4Z104J- R CARBON FILM 1/4 100K OHM J R538 RD-4Z104J- R CARBON FILM 1/4 100K OHM J R539 RD-2Z180J- R CARBON FILM 1/2 18 OHM J R540 RD-2Z470J- R CARBON FILM 1/2 47 OHM J R541 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R542 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R543 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J R544 HRFT391JCA R CHIP 1/10 390 OHM J 2012 R545 HRFT154JCA R CHIP 1/10 150K OHM J 2012 R546 RD-AZ154J- R CARBON FILM 1/6 150K OHM J R547 RD-AZ682J- R CARBON FILM 1/6 6.8K OHM J R548 RD-AZ333J- R CARBON FILM 1/6 33K OHM J R549 HRFT513JCA R CHIP 1/10 51K OHM J 2012 R550 RD-AZ563J- R CARBON FILM 1/6 56K OHM J R552 HRFT000JCA R CHIP 1/10 0 OHM J 2012 R553 RD-AZ474J- R CARBON FILM 1/6 470K OHM J R554 RD-AZ204J- R CARBON FILM 1/6 200K OHM J R555 HRFT392JCA R CHIP 1/10 3.9K OHM J 2012 R557 RD-AZ471J- R CARBON FILM 1/6 470 OHM J R560 HRFT564JCA R CHIP 1/10 560K OHM J 2012 R561 HRFT683JCA R CHIP 1/10 68K OHM J 2012 R562 HRFT332JCA R CHIP 1/10 3.3K OHM J 2012 R563 RD-AZ474J- R CARBON FILM 1/6 470K OHM J R564 RD-AZ391J- R CARBON FILM 1/6 390 OHM J R565 HRFT472JCA R CHIP 1/10 4.7K OHM J 2012 R566 HRFT434JCA R CHIP 1/10 430K OHM J 2012 R568 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R569 RD-AZ222J- R CARBON FILM 1/6 2.2K OHM J R570 HRFT273JCA R CHIP 1/10 27K OHM J 2012 R571 HRFT333JCA R CHIP 1/10 33K OHM J 2012
LOC PART-CODE PART-NAME PART-DESC
R255 HRFT562JCA R CHIP 1/10 5.6K OHM J 2012 R256 HRFT105JCA R CHIP 1/10 1M OHM J 2012 R257 RD-AZ511J- R CARBON FILM 1/6 510 OHM J R258 RD-AZ181J- R CARBON FILM 1/6 180 OHM J R259 RD-4Z751J- R CARBON FILM 1/4 750 OHM J R260 HRFT333JCA R CHIP 1/10 33K OHM J 2012 R261 RD-AZ471J- R CARBON FILM 1/6 470 OHM J R262 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R263 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R264 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R265 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R267 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R268 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R269 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R270 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R271 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R272 RD-AZ562J- R CARBON FILM 1/6 5.6K OHM J R273 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R274 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R275 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R276 RD-AZ183J- R CARBON FILM 1/6 18K OHM J R277 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R278 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R279 HRFT202JCA R CHIP 1/10 2K OHM J 2012 R280 RD-AZ393J- R CARBON FILM 1/6 39K OHM J R281 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R401 HRFT223JCA R CHIP 1/10 22K OHM J 2012 R402 HRFT393JCA R CHIP 1/10 39K OHM J 2012 R403 HRFT393JCA R CHIP 1/10 39K OHM J 2012 R404 HRFT683JCA R CHIP 1/10 68K OHM J 2012 R405 RD-AZ563J- R CARBON FILM 1/6 56K OHM J R406 HRFT273JCA R CHIP 1/10 27K OHM J 2012 R407 HRFT183JCA R CHIP 1/10 18K OHM J 2012 R408 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R409 RD-AZ102J- R CARBON FILM 1/6 1K OHM J R411 RN-2Z1008F R METAL FILM 1/2 1.0 OHM F R412 RD-2Z100J- R CARBON FILM 1/2 10 OHM J R413 RS01Z151J- R M-OXIDE FILM 1W 150 OHM J (TAPPING) R414 RD-AZ242J- R CARBON FILM 1/6 2.4K OHM J R415 RD-2Z101J- R CARBON FILM 1/2 100 OHM J R416 RD-4Z363J- R CARBON FILM 1/4 36K OHM J R417 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R418 RD-AZ221J- R CARBON FILM 1/6 220 OHM J R419 RD-AZ471J- R CARBON FILM 1/6 470 OHM J R423 RD-AZ431J- R CARBON FILM 1/6 430 OHM J R501 RD-AZ122J- R CARBON FILM 1/6 1.2K OHM J R502 HRFT153JCA R CHIP 1/10 15K OHM J 2012 R503 RD-AZ623J- R CARBON FILM 1/6 62K OHM J R504 RD-4Z244J- R CARBON FILM 1/4 240K OHM J R505 RD-AZ303J- R CARBON FILM 1/6 30K OHM J R506 RD-AZ473J- R CARBON FILM 1/6 47K OHM J R507 RD-AZ222J- R CARBON FILM 1/6 2.2K OHM J R508 HRFT472JCA R CHIP 1/10 4.7K OHM J 2012 R509 RD-2Z100J- R CARBON FILM 1/2 10 OHM J R510 RN-AZ3002F R METAL FILM 1/6 30.0K OHM F
LOC PART-CODE PART-NAME PART-DESC
42
R844 RD-4Z220J- R CARBON FILM 1/4 22 OHM J R845 RC-2Z470J- R CARBON COMP 1/2 47 OHM J R847 RD-AZ105J- R CARBON FILM 1/6 1M OHM J R848 HRFT104JCA R CHIP 1/10 100K OHM J 2012 R849 HRFT473JCA R CHIP 1/10 47K OHM J 2012 R850 HRFT273JCA R CHIP 1/10 27K OHM J 2012 R851 HRFT622JCA R CHIP 1/10 6.2K OHM J 2012 R852 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R860 RD-AZ330J- R CARBON FILM 1/6 33 OHM J R861 HRFT750JCA R CHIP 1/10 75 OHM J 2012 R862 HRFT432JCA R CHIP 1/10 4.3K OHM J 2012 R863 HRFT682JCA R CHIP 1/10 6.8K OHM J 2012 R864 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R866 HRFT331JCA R CHIP 1/10 330 OHM J 2012 R867 RD-AZ121J- R CARBON FILM 1/6 120 OHM J R868 RD-AZ470J- R CARBON FILM 1/6 47 OHM J R869 HRFT510JCA R CHIP 1/10 51 OHM J 2012 R870 HRFT750JCA R CHIP 1/10 75 OHM J 2012 R871 RS02Z242JS R M-OXIDE FILM 2W 2.4K OHM J SMALL R872 RS02Z242JS R M-OXIDE FILM 2W 2.4K OHM J SMALL R873 RD-4Z220J- R CARBON FILM 1/4 22 OHM J R874 RD-4Z220J- R CARBON FILM 1/4 22 OHM J R875 RC-2Z470J- R CARBON COMP 1/2 47 OHM J R877 RD-AZ105J- R CARBON FILM 1/6 1M OHM J R878 HRFT104JCA R CHIP 1/10 100K OHM J 2012 R879 HRFT473JCA R CHIP 1/10 47K OHM J 2012 R880 HRFT273JCA R CHIP 1/10 27K OHM J 2012 R881 HRFT622JCA R CHIP 1/10 6.2K OHM J 2012 R882 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R891 RD-4Z562J- R CARBON FILM 1/4 5.6K OHM J R892 RD-4Z564J- R CARBON FILM 1/4 560K OHM J R893 RS01Z569J- R M-OXIDE FILM 1W 5.6 OHM J (TAPPING) RL001 5SC0101005 SW RELAY HR-CR313 DC12V 1C-1P SC001 9970800029 CABLE SIGNAL AS 15P+2C/DDC=1.5M(GY275A) SG801 4SG0D00104 SPARK GAP S-23 1.5KV SG831 4SG0D00104 SPARK GAP S-23 1.5KV SG861 4SG0D00104 SPARK GAP S-23 1.5KV SG890 4SG0D00104 SPARK GAP S-23 1.5KV SG891 4SG0D00104 SPARK GAP S-23 1.5KV SW201 5S50101Z01 SW TACT KPT-1115VM 1C-1P SW202 5S50101Z01 SW TACT KPT-1115VM 1C-1P SW203 5S50101Z01 SW TACT KPT-1115VM 1C-1P SW204 5S50101Z01 SW TACT KPT-1115VM 1C-1P SW205 5S50101Z01 SW TACT KPT-1115VM 1C-1P SW206 5S50101Z01 SW TACT KPT-1115VM 1C-1P T001 5RM0000095 TRANS SMPS DWT-523X T002 5RY0000003 TRANS SYNC DST-602 T500 5RH0000096 FBT FFA81045H T501 5RD0000034 TRANS DRIVE DDT-130 T502 5RP0000035 TRANS CHOPPER DCT-602T TH001 DPJ502140M POSISTOR J502P53D140M290 TH002 DTP8D13--- THERMISTOR TP8D13 VR101 RV6421201P R SEMI FIXED CCT 065AT 200 OHM B TAP VR501 RV6421104P R SEMI FIXED CCT 065AT 100K OHM B TAP VR502 RV6421204P R SEMI FIXED CCT 065AT 200K OHM B TAP X201 5PEF0EC8T4 RESONATOR EFOEC8004T4
LOC PART-CODE PART-NAME PART-DESC
R572 RD-AZ563J- R CARBON FILM 1/6 56K OHM J R573 HRFT622JCA R CHIP 1/10 6.2K OHM J 2012 R574 HRFT203JCA R CHIP 1/10 20K OHM J 2012 R575 RD-AZ563J- R CARBON FILM 1/6 56K OHM J R580 RD-AZ824J- R CARBON FILM 1/6 820K OHM J R581 RD-4Z123J- R CARBON FILM 1/4 12K OHM J R582 RD-AZ154J- R CARBON FILM 1/6 150K OHM J R583 RD-AZ273J- R CARBON FILM 1/6 27K OHM J R584 HRFT512JCA R CHIP 1/10 5.1K OHM J 2012 R585 HRFT102JCA R CHIP 1/10 1K OHM J 2012 R586 RD-AZ103J- R CARBON FILM 1/6 10K OHM J R587 RD-AZ104J- R CARBON FILM 1/6 100K OHM J R590 RD-AZ753J- R CARBON FILM 1/6 75K OHM J R591 HRFT912JCA R CHIP 1/10 9.1K OHM J 2012 R592 HRFT122JCA R CHIP 1/10 1.2K OHM J 2012 R593 RD-AZ472J- R CARBON FILM 1/6 4.7K OHM J R594 RD-AZ822J- R CARBON FILM 1/6 8.2K OHM J R595 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R596 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R597 HRFT103JCA R CHIP 1/10 10K OHM J 2012 R800 RD-AZ330J- R CARBON FILM 1/6 33 OHM J R801 HRFT750JCA R CHIP 1/10 75 OHM J 2012 R802 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R803 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R804 HRFT911JCA R CHIP 1/10 910 OHM J 2012 R805 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R806 HRFT331JCA R CHIP 1/10 330 OHM J 2012 R807 RD-AZ121J- R CARBON FILM 1/6 120 OHM J R808 RD-AZ470J- R CARBON FILM 1/6 47 OHM J R809 HRFT910JCA R CHIP 1/10 91 OHM J 2012 R810 HRFT750JCA R CHIP 1/10 75 OHM J 2012 R811 RS02Z242JS R M-OXIDE FILM 2W 2.4K OHM J SMALL R812 RS02Z242JS R M-OXIDE FILM 2W 2.4K OHM J SMALL R813 RD-4Z220J- R CARBON FILM 1/4 22 OHM J R814 RD-4Z220J- R CARBON FILM 1/4 22 OHM J R815 RC-2Z470J- R CARBON COMP 1/2 47 OHM J R817 RD-AZ105J- R CARBON FILM 1/6 1M OHM J R818 HRFT104JCA R CHIP 1/10 100K OHM J 2012 R819 HRFT473JCA R CHIP 1/10 47K OHM J 2012 R820 HRFT273JCA R CHIP 1/10 27K OHM J 2012 R821 HRFT622JCA R CHIP 1/10 6.2K OHM J 2012 R822 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R830 RD-AZ330J- R CARBON FILM 1/6 33 OHM J R831 HRFT750JCA R CHIP 1/10 75 OHM J 2012 R832 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R833 HRFT101JCA R CHIP 1/10 100 OHM J 2012 R834 HRFT182JCA R CHIP 1/10 1.8K OHM J 2012 R835 RD-AZ101J- R CARBON FILM 1/6 100 OHM J R836 HRFT331JCA R CHIP 1/10 330 OHM J 2012 R837 RD-AZ121J- R CARBON FILM 1/6 120 OHM J R838 RD-AZ470J- R CARBON FILM 1/6 47 OHM J R839 HRFT750JCA R CHIP 1/10 75 OHM J 2012 R840 HRFT750JCA R CHIP 1/10 75 OHM J 2012 R841 RS02Z242JS R M-OXIDE FILM 2W 2.4K OHM J SMALL R842 RS02Z242JS R M-OXIDE FILM 2W 2.4K OHM J SMALL R843 RD-4Z220J- R CARBON FILM 1/4 22 OHM J
LOC PART-CODE PART-NAME PART-DESC
43
!
! ! ! !
!
Service Manual
DAEWOO ELECTRONICS CO., LTD
OVERSEAS SERVICE DEPT.
DAEWOO ELECTRONICS CO., LTD
686, AHYEON-DONG MAPOGU, SEOUL, KOREA. C.P.O. BOX 8003 SEOUL KOREA TELEX: DWELEC K28177-8 CABLE: "DAEWOOELEC" FAX: 02) 590-6291 TEL: 02) 360-7114/590-6151~5 http://www.dwe.daewoo.co.kr
PRINTED DA TE:JUNE.1999
Loading...