DAEWOO KOR-180A2A, KOR-181G2A, KOR-181H2A Service Manual

Service Manual

Microwave Oven

Model: KOR-180A2A

KOR-181G2A

KOR-181H2A

DAEWOO ELECTRONICS CO., LTD.

S/M No. : R180A2A001

PRECA UTIONS T O BE OBSERVED BEFORE AND DURING SER VICING T O AVOID POSSIBLE EXPOSURE T O EXCESSIVE MICROW AVE ENERGY

(a)Do not operate or allow the oven to be operated with the door open. (b)Make the following safety checks on all ovens to be serviced before activating the magnetron or other

microwave source, and make repairs if necessary: (1) Interlock operation, (2) Proper door closing, (3) Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and latches (5) Evidence of dropping or abuse.

(c)Before turning on power to the microwave oven for any service test or inspection within the microwave

generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.

(d) Any defective or misadjusted components in the interlock, monitor, door seal and microwave

generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.

(e) A microwave leakage check to verify compliance with the Federal performance standard should be

performed on each oven prior to release to the owner.

TABLE OF CONTENTS

SAFETY AND PRECAUTIONS........................................................................................................................................3

FOR SAFE OPERATION...........................................................................................................................................3

FOR SAFE SERVICE PROCEDURES .....................................................................................................................3

SPECIFICATIONS ............................................................................................................................................................4

EXTERNAL VIEW.............................................................................................................................................................5

OUTER DIMENSION.................................................................................................................................................5

FEATURE DIAGRAM.................................................................................................................................................6

CONTROL PANEL.....................................................................................................................................................7

INSTALLATION..............................................................................................................................................................10

OPERATIONS AND FUNCTIONS .................................................................................................................................11

DISASSEMBLY AND ASSMBLY...................................................................................................................................12

INTERLOCK MECHANISM AND ADJUSTMENT.........................................................................................................19

TROUBLE SHOOTING GUIDE......................................................................................................................................20

MESUREMENT AND TEST............................................................................................................................................24

MEASUREMENT OF THE MICROWAVE POWER OUTPUT................................................................................24

MICROWAVE RADIATION TEST ...........................................................................................................................25

COMPONENT TEST PROCEDURE.......................................................................................................................26

WIRING DIAGRAM.........................................................................................................................................................27

PRINTED CIRCUIT BOARD...........................................................................................................................................28

CIRCUIT CHECK PROCEDURE.............................................................................................................................28

PCB CIRCUIT DIAGRAM ........................................................................................................................................31

P.C.B. LOCATION NO.............................................................................................................................................32

EXPLODED VIEW AND PARTS LIST...........................................................................................................................33

DOOR ASSEMBLY..................................................................................................................................................33

CONTROL PANEL ASSEMBLY..............................................................................................................................33

TOTAL ASSEMBLY.................................................................................................................................................33

SAFETY AND PRECA UTIONS

CAUTION : This Device is to be Serviced Only by Properly Qualified Service Personnel. Consult the Service

Manual for Proper Service Procedures to Assure Continued Safety Operation and for Precautions to be Taken to Avoid Possible Exposure to Excessive Microwave Energy.

1. FOR SAFE OPERATION

Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE. (Only a trained service personnel should make repairs.)

1) A broken door hinge.

2) A broken door viewing screen.

3) A broken front panel, oven cavity.

4) A loosened door lock.

5) A broken door lock. The door gasket plate and oven cavity surface should be kept clean. No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven. DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN. The microwave oven has concealed switches to make sure the power is turned off when the door is opened. Do not attempt to defeat them. DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.

2. FOR SAFE SERVICE PROCEDURES

1) If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the oven.

2) If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the oven.

(a) inform the manufacturer, importer or assembler, (b) repair the unit at no cost to the owner, (c) attempt to ascertain the cause of the excessive leakage, (d) tell the owner of the unit not to use the unit until the oven has been brought into compliance.

3) If the oven operates with the door open, the service person should tell the user not to operate the oven and contact the manufacturer and CDRH immediately.

CAUTION

MICROWAVE RADIATION

PERSONNEL SHOULD NOT BE EXPOSED TO THE MICROWAVE ENERGY WHICH MAY RADIATE FROM THE MAGNETRON OR OTHER MICROWAVE GENERATING DEVICE IF IT IS IMPROPERLY USED OR CONNECTED. ALL INPUT AND OUTPUT MICROWAVE CONNECTIONS. WAVEGUIDES FLANGES AND GASKETS MUST BE SECURED. NEVER OPERATE THE DEVICE WITHOUT A MICROWAVE ENERGY ABSORBING LOAD ATTACHED. NEVER LOOK INTO AN OPEN WAVEGUIDE OR ANTENNA WHILE THE DEVICE IS ENERGIZED.

SPECIFICATIONS

MODEL KOR-180A2A/181G2A/181H2A POWER SUPPLY 120V~60HZ, SINGLE PHASE WITH EARTHING

MICROWAVE 1600 W

POWER

GRILL

CONSUMPTION

COMBINATION MICROWAVE ENERGY OUTPUT 1200 W MICROWAVE FREQUENCY 2450MHz OUTSIDE DIMENSIONS (W X H X D) 589X339X487mm (23.2X13.3X19.2 in.) CAVITY DIMENSIONS (W X H X D) 399X278X451mm (15.7X10.9X17.8 in.) NET WEIGHT APPROX. 18.0kg (39.7 lbs.) TIMER 99min. 99sec. FUNCTION SELECTIONS MICROWAVE POWER SELECTIONS 10 LEVELS CAVITY VOLUME 1.8 Cu. Ft

* Specifications are subject to change without notice.

EXTERNAL VIEW

1. OUTER DIMENSION

1. DOOR SEAL

Door seal maintains the microwave within the oven cavity and prevents microwave leakage.

2. DOOR HOOK

When door is closed, it will automatically lock shut. If door is opened while oven is operating, magnetron tube will immediately stop operating.

3. DOOR SCREEN

Allows viewing of food. Microwave cannot pass through perforations in screen.

4. SPATTER SHIELD

Protects the microwave outlet from splashes of cooking foods.

5. OVEN LAMP

Automatically turns on during oven operating.

6. SAFETY INTERLOCK SYSTEM

7. CONTROL PANEL

8. GLASS COOKING TRAY

Made of special heat resisant glass. The tray must always be in proper position before operating. Do not cook food directly on the tray.

9. OVEN FRONT PLATE

10. DOOR OPENING BUTTON

To open the door, push the door opening button. When door is closed, it will automatically lock shut. If door is opened while oven is operating, magnetron tube will immediately stop operating.

11. ROLLER GUIDE

Supports the glass cooking tray.

2. FEATURE DIAGRAM

KOR-180A

1. Time set pad - Used to set the cooking time and the present time.

2. Display - Cooking time, power level, indicators and present time are displayed.

3. One touch - Used to cook or reheat specific quantities of food.

4. Auto cook - Used to cook or reheat.

5. More - Used to add time to cooking.

6. Less - Used to remove time from cooking.

7. Auto Defrost - Used to defrost foods.(for weight)

8. Power - Used to set power level.

9. Defrost - Used to defrost foods.(for time)

10. Kitchen Timer - Used as a minute timer, delay cooking, hold setting after cooking.

11. Clock - Used to set clock.

12. Stop/Clear - Used to stop the oven operation or to delete the cooking data.

13. Start/Easy cook - Used to start the oven and also used to set a reheat time.

3. CONTROL PANEL

(1) KOR-180A2A

M/W DEF

AUTO COOK

1. BREAD

2. SOUP

3. BAKED POTATO

4. FRESH VEGETABLE

5. FROZEN VEGETABLE

LESS

TIMER LOCK lb

POPCORN

FROZEN

PIZZA

DINNER

PLATE

MEAT

POWER

DEFROST

POULTRY FISH

STOP/

CLEAR

START/

SPEEDY COOK

AUTO DEFROST

CLOCK

KITCHEN

TIMER

123 456 789

MICROWAVE OVEN KOR-181G

1. Time set pad - Used to set the cooking time and the present time.

2. Display - Cooking time, power level, indicators and present time are displayed.

3. One touch - Used to cook or reheat specific quantities of food.

4. Auto cook - Used to cook or reheat.

5. More - Used to add time to cooking.

6. Less - Used to remove time from cooking.

7. Auto Defrost - Used to defrost foods.(for weight)

8. Power - Used to set power level.

9. Defrost - Used to defrost foods.(for time)

10. Kitchen Timer - Used as a minute timer, delay cooking, hold setting after cooking.

11. Clock - Used to set clock.

12. Stop/Clear - Used to stop the oven operation or to delete the cooking data.

13. Start/Easy cook - Used to start the oven and also used to set a reheat time.

(2) KOR-181G2A

M/W DEF

BEVERAGE

FRESH

VEGETABLE

FROZEN

VEGETABLE

LESS

TIMER LOCK lb

POPCORN

FROZEN

PIZZA

DINNER

PLATE

MEAT

POWER

DEFROST

POULTRY FISH

STOP/

CLEAR

START/

SPEEDY COOK

AUTO DEFROST

CLOCK

KITCHEN

TIMER

123 456 789

MICROWAVE OVEN KOR-181H

1. Time set pad - Used to set the cooking time and the present time.

2. Display - Cooking time, power level, indicators and present time are displayed.

3. One touch - Used to cook or reheat specific quantities of food.

4. More - Used to add time to cooking.

5. Less - Used to remove time from cooking.

6. Auto Defrost - Used to defrost foods.(for weight)

7. Power - Used to set power level.

8. Defrost - Used to defrost foods.(for time)

9. Kitchen Timer - Used as a minute timer, delay cooking, hold setting after cooking.

10. Clock - Used to set clock.

11. Stop/Clear - Used to stop the oven operation or to delete the cooking data.

12. Start/Easy cook - Used to start the oven and also used to set a reheat time.

(3) KOR-181H2A

INSTALLATION

1. Steady, flat location.

This microwave oven should be set on a steady, flat surface.

2.Leave space behind and side.

All air vents should be kept a clearance. If all vents are covered during operation, the oven may be overheated and, eventually, cause oven failure.

3.A way from radio, and TV sets

Poor television reception and radio interference may result if the oven is located close to a TV, radio, antenna, or feeder and so on. Position the oven as far from them as possible.

4.A way from heating appliances and water taps

Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be adversely affected and breakdowns occur.

5.Power suppl y

• Check your local power source. This microwave oven requires a current of approximately 14.5 amperes, 120Volts, 60Hz grounded outlet.

1. A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or trippping over a

longer cord.

2. Longer cord sets or extension cords are available and may be used if care is exercised in their use.

3. If a long cord or extension cord is used:

1) The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating

of the appliance.

2) The extension cord must be a grounding type 3-wire cord.

3) The longer cord should be arranged so that it will not drape over the counter top or tabletop where it can be

pulled on by children or tripped over unintentionally.

6. Examine the oven after unpacking for any damage such as:

A misaligned door, broken door or a dent in cavity. If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.

OPERATIONS AND FUNCTIONS

1. Connect the main lead to an electrical outlet.

2. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking.

3. Close the door securely.

The oven door can be opened at any time during operation by touching the door release button on the control panel.

The oven will automatically shut off. To restart the oven, close the door and then touch START.

5. Each time a pad is touched, a BEEP will sound to acknowledge the touch.

6. The oven automatically cook on full power unless set to a lower power level.

7. The display will show : 0 when the oven is plugged in.

8. Time clock returns to the present time when the cooking time ends.

9. When the STOP/CLEAR pad is touched during the oven operation, the oven stops cooking and all information retained.

To erase all information (except the present time), touch the STOP/CLEAR pad once more. If the oven door is opened during the oven operation, all information is retained.

10. If the START pad is touched and the oven does not operate, check the area between the door and door is closed

securely. The oven will not start cooking under the door is not completely closed or the program has not been set.

Wattage output chart

The power level is set by pressing the POWER pad. The chart shows the display, the power level and the percentage of power.

Make sure the oven is properly installed and plugged into the electrical outlet.

Touch POWER pad. Power level(Display) Approximate Percentage of Power

Once P-HI 100%

Twice P-90 90% 3 times P-80 80% 4 times P-70 70% 5 times P-60 60% 6 times P-50 50% 7 times P-40 40% 8 times P-30 30% 9 times P-20 20%

10 times P-10 10% 11 times P-00 0%

DISASSEMBLY AND ASSEMBLY

- Cautions to be observed when trouble shooting.

Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible danger from a short circuit. You are asked to observe the following precautions carefully.

1. Always remove the power plug from the outlet before servicing.

2. Use an insulated screwdriver and wear rubber gloves when servicing the high voltage side.

3. Discharge the high voltage capacitor before touching any oven components or wiring. (1) Check the grounding.

Do not operate on a two-wire extension cord. The microwave oven is designed to be used while grounded. It is imperative, therefore, to make sure it is grounded properly before beginning repair work.

(2) Warning about the electric charge in the high voltage capacitor.

For about 30 seconds after the operation has stopped, electric charge remains in the high voltage capacitor. When replacing or checking parts, short between oven chassis and the negative high terminal of the high voltage capacitor by using a properly insulated screwdriver to discharge.

4. When the 20A fuse is blown due to the operation of the monitor

switch; replace primary interlock switch, secondary interlock switch and interlock monitor switch.

5. After repair or replacement of parts, make sure that the screws are

properly tightened, and all electrical connections are tightened.

6. Do not operate without cabinet.

CAUTION : Service personnel should remove their watches whenever working close to or replacing the magnetron.

WARNING :When servicing the appliance, take care when touching or replacing high potential parts because of

electrical shock or exposing microwave. These parts are as follows - HV Transformer, Magnetron, HV Capacitor, HV Diode.

+ 25 hidden pages