Daewoo KOR-145M0P, KOR-145Q0P Service Manual

Service Manual
Microwave Oven
Model: KOR-145M0P
KOR-145Q0P
DAEWOO ELECTRONICS CO., LTD.
: In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information,please refer to PPL(Parts Price List) in Service Information Center (http://svc.dwe.co.kr).
2
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWA VE ENERGY
(a)Do not operate or allow the oven to be operated with the door open. (b)Make the following safety checks on all ovens to be serviced before activating the magnetron or other micro-
wave source, and make repairs as necessary: (1) Interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating com-
partments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connections.
(d)Any defective or misadjusted components in the interlock, monitor, door seal and microwave generation and
transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.
(e)A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
TABLE OF CONTENTS
PROPER USE AND SERVICE PRECAUTIONS .......................................................................................................................3
SPECIFICATIONS.......................................................................................................................................................................4
FEATURE DIAGRAM..................................................................................................................................................................5
EARTHING INSTRUCTIONS......................................................................................................................................................7
INSTALLATION...........................................................................................................................................................................7
OPERATION PROCEDURE.......................................................................................................................................................8
CONTROLS.................................................................................................................................................................................9
INTERLOCK MECHANISM FUNCTIONS AND ADJUSTMENT..............................................................................................24
MEASUREMENT OF THE MICROWAVE OUTPUT POWER.................................................................................................26
MICROWAVE EMISSION TEST...............................................................................................................................................26
WIRING DIAGRAM...................................................................................................................................................................27
CIRCUIT DESCRIPTION..........................................................................................................................................................28
SAFETY PRECAUTIONS FOR DISASSEMBLY AND REPAIR..............................................................................................31
DISASSEMBLY AND ASSEMBLY............................................................................................................................................32
TROUBLE SHOOTING GUIDE ................................................................................................................................................38
COMPONENT TEST PROCEDURE........................................................................................................................................ 47
PRINTED CIRCUITS BOARD...................................................................................................................................................49
CIRCUIT CHECK PROCEDURE.......................................................................................................................................49
PCB CIRCUIT DIAGRAM....................................................................................................................................................54
COMPONENT INFORMATION...........................................................................................................................................55
PRINTED CIRCUITS BOARD.............................................................................................................................................56
P.C.B. LOCATION NO ........................................................................................................................................................57
EXPLODED AND PARTS LIST................................................................................................................................................58
EXPLODED VIEW.....................................................................................................................................................................60
3
PROPER USE AND SERVICE PRECAUTIONS
CAUTION : This Device is to be Serviced Only by Properly Qualified Service Personnel. Consult the Service
Manual for Proper Service Procedures to Assure Continued Safety Operation and for Precautions to be Taken to Avoid Possible Exposure to Excessive Microwave Energy.
1. For Safe Operation
Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may cause serious bodily injury to the operator. IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE. (Only a trained service personnel should make repairs.)
1) A broken door hinge.
2) A broken door viewing screen.
3) A broken front panel, oven cavity.
4) A loosened door lock.
5) A broken door lock. The door gasket plate and oven cavity surface should be kept clean. No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven. DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN. The microwave oven has concealed switches to make sure the power is turned off when the door is opened. Do not attempt to defeat them. DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
2. For Safe Service Procedures
1) If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the oven.
2) If any certified oven unit is found to have excessive emission level 4mW/cm
2
, the service person should: (a) inform the manufacturer, importer or assembler, (b) repair the unit at no cost to the owner, (c) attempt to ascertain the cause of the excessive leakage, (d) tell the owner of the unit not to use the unit until the oven has been brought into compliance.
3)
If the oven operates with the door open, the service person should tell the user not to operate the oven and contact the manufacturer and CDRH immediately.
4
SPECIFICATIONS
POWER SUPPLY 220V~60Hz, SINGLE PHASE WITH EARTHING
POWER CONSUMPTION 1350 W
MICROWAVE OUTPUT POWER 900 W (IEC 705)
FREQUENCY 2450 MHZ OUTSIDE DIMENSIONS (W X H X D) 560 X 360 X 396 mm (22 X 14.2 X 15.6 in.) CAVITY DIMENSIONS (W X H X D) 382 X 270 X 360 mm (15.0 X 10.6 X 14.2 in.) NET WEIGHT APPROX. 18.5 K g (40.8 Ibs.) TIMER 99 min. 99 sec. POWER SELECTIONS 10 LEVELS
* Specifications subject to change without notice.
5
FEATURES DIAGRAM (KOR-145M)
LESS
5 0
1. BAKED POTATO
2. FRESH VEGETABLE
3. SOUP
4. FISH FILLETS
5. MEAT LOAF
AUTO COOK
MENU
POPCORN
MUFFIN
MORE LESS
BEVERAGE
SPEEDY COOK
FROZEN
PIZZA
DINNER
PLATE
WEIGHT
1
STAGE
2
WEIGHT TIME
AUTO START
DEFROST
LOCK NO
CUPS g
STOP/CLEAR START
Auto
defrost
Clock /
Auto Start
12345 67890
Power
1 2 3 4 5
6
9
7
11
19 15
17
16
23 22
25
13
12
18 21
14
20
24
10
26
8
1. BAKED POTATO
2. FRESH VEGETABLE
3. SOUP
4. FISH FILLETS
5. MEAT LOAF
AUTO COOK
MENU
POPCORN
MUFFIN
MORE
BEVERAGE
SPEEDY COOK
FROZEN
PIZZA
DINNER
PLATE
WEIGHT
1
STAGE
2
WEIGHT TIME
AUTO
START
DEFROST
LOCK NO
CUPS g
STOP/CLEAR START
Auto
defrost
Clock /
Auto Start
1234 6789
Power
1 Door latch - When the door is closed it will automat-
ically lock shut. If the door is opened while the oven is operating. The magnetron will automatically shut off.
2 Door seal - The door seal maintains the microwave
within the oven cavity and prevents microwave leakage.
3 Oven cavity 4 Spatter shield - Protects the microwave outlet from
splashes of cooking foods.
5 Safety interlock system - Prevents the oven from
operating while the door is opened.
6 Door release button - Pushing this button stops oven
operation and opens the door.
7 Glass cooking tray - Made of special heat resistant
glass. The tray must always be in proper position before operating. Do not cook food directly on the tray.
8 Roller guide - Supports the glass cooking tray. 9 Door screen - Allows viewing of food. The screen is
designed so that light can pass through, but not the microwaves.
0 Time set pad - Used to set the cooking time and the
present time.
q Display - Cooking time, power level, present time are
displayed.
w Menu - Used to select foods. e Weight - Used to select quantity of foods. r Speedy cook - Touch to set the any desired reheat
setting.
t Popcorn - Used to cook popcorn. y Muffin - Used to cook muffin. u Dinner plate - Used to reheat dinner plate. i Beverage - Used to reheat beverage. o Frozen pizza - Used to reheat frozen pizza. p More - Used to increase on one touch cooking. a Less - Used to decreasee one touch cooking. s Auto defrost - Used to defrost foods. d Power - Used to set power level. f Clock / A.start -Used to set clock & Used to set auto
start.
g Stop / Clear - Used to stop the oven operation or to
delete the cooking data.
h Start - Used to start a selected operation.
6
FEATURES DIAGRAM (KOR-145Q)
1 2 3 4 5
6
9
7
11
15
13
21
12
14
22
16
23
24
26
18
17
19
20
10
25
27
8
AUTO
DEF.
SPEEDY
COOK
POPCORN
SOUP
MUFFIN
BEVERAGE
BAKED
POTATO
FROZEN
PIZZA
DINNER
PLATE
FRESH
VEGETABLE
1
STAGE
2
WEIGHT TIME
AUTO
START
DEFROST
LOCK NO
CUPS g
STOP/ CLEAR
START
1 2 3 4 5 6 7 809
Power
Clock/ A.Start
AUTO DEF.
SPEEDY
COOK
POPCORN
SOUP
MUFFIN
BEVERAGE
BAKED
POTATO
FROZEN
PIZZA
DINNER PLATE
FRESH
VEGETABLE
1
STAGE
2
WEIGHT TIME
AUTO START
DEFROST
LOCK NO
CUPS g
STOP/ CLEAR
START
1 2 3 4 5 6 7 809
Power
Clock/ A.Start
1 Door latch - When the door is closed it will automat-
ically lock shut. If the door is opened while the oven is operating. The magnetron will automatically shut off.
2 Door seal - The door seal maintains the microwave
within the oven cavity and prevents microwave leakage.
3 Oven cavity 4 Spatter shield - Protects the microwave outlet from
splashes of cooking foods.
5 Safety interlock system - Prevents the oven from
operating while the door is opened.
6 Door release button - Pushing this button stops oven
operation and opens the door.
7 Glass cooking tray - Made of special heat resistant
glass. The tray must always be in proper position before operating. Do not cook food directly on the tray.
8 Roller guide - Supports the glass cooking tray. 9 Door screen - Allows viewing of food. The screen is
designed so that light can pass through, but not the microwaves.
0 Time set pad - Used to set the cooking time and the
present time.
q Display - Cooking time, power level, present time are
displayed.
w Speedy cook - Touch to set the any desired reheat
setting.
e Popcorn - Used to cook popcorn. r Muffin - Used to cook muffin. t Baked potato - Used to cook baked potato. y Dinner plate - Used to reheat dinner plate. u Soup - Used to reheat soup. i Beverage - Used to reheat beverage. o Frozen pizza - Used to reheat frozen pizza. p Fresh vegetable - Used to blanch fresh vegetable. a More - Used to increase on one touch cooking. s Less - Used to decrease one touch cooking. d Auto defrost - Used to defrost foods. f Power - Used to set power level. g Clock / A.start -Used to set clock & Used to set auto
start.
h Stop / Clear - Used to stop the oven operation or to
delete the cooking data.
j Start - Used to start a selected operation.
7
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of electric shock by providing an escape, wire for the electric current. This appliance is equipped with a cord having a earthing wire with a earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.
1. Steady, flat location
This oven should be set on a steady, flat surface. This oven is designed for counter top use only.
2. Leave space behind and side
All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually, oven failure.
3. Away from Radio and TV sets
Poor television reception and radio interference may result if the oven is located close to a TV, Radio, or antenna, feeder and so on. Position the oven as far from them as possible.
4. Away from heating appliances and water taps
Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be adversely affected and breakdowns occur.
5. Power supply
• Check your local power source.This oven requires a current of approximately 12 amperes, 220V 60Hz.
• Power supply cord is about 1.0 meters long.
• The voltage used must be the same as specified on this Microwave Oven. Using a higher voltage may result in a tire or other accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage resulting from use of this oven with a voltage of ampere fuse other than those specified.
• This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same type. Such a cable can be purchased from DAEWOO and must be installed by a Qualified Person.
6. Examine the oven after unpacking for any damage such as:
A misaligned door, Broken door, A dent in cavity. If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
7. Do not operate the oven if it is colder than room temperature.
(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.
INSTALLATION
WARNING : Improper use of the earthing plug can result in a risk of electric shock. Consult a qualified electrician or
serviceman if the earthing instructions are not completely understood, or if doubt exists as to whether the appliance is properly earthed. If it necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade earthing plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord should be equal to or greater than the electrical rating of the appliance.
8
This section includes useful information about oven operation.
1. Plug power supply cord into a 230V 50Hz power outlet.
2. After placing the food in a suitable container, open the oven door and put it on the glass tray. The glass tray must always be in place during cooking.
3. Shut the door. Make sure that it is firmly closed.
Wattage output chart
• The power-level is set by touching the POWER pad. The chart shows the display, the power level and the percentage of
power.
OPERATION PROCEDURE
1
When the oven door is opened, the light turns on.
2
The oven door can be opened at any time during operation by pressing the door release button on the control panel. The oven will automatically shut off. To restart the oven, close the door and then touch START.
3
Each time a pad is touched, a BEEP will sound to acknowledge the touch.
4
The oven automatically cook on full power unless set to a lower power level.
5
The display will show “:0” when the oven is plugged in.
6
Time clock returns to the present time when the cooking time ends.
7
When the STOP/CLEAR pad is touched during the oven operation, the oven stops cooking and all information retained. To erase all information (except the present time), touch the STOP/CLEAR pad once more. If the oven door is opened during the oven operation, all information is retained.
8
If the START pad is touched and the oven does not
operate, check the area between the door and door seal for obstructions and make sure the door is closed securely. The oven will not start cooking until the door is completely closed or the program has been reset.
Make sure the oven is properly installed and plugged into the electrical outlet
Touch Power Pad,
Power Level (Display)
Approximate Percentage
Once the Touch of Power
POWER P-HI 100 %
9 P-90 90 % 8 P-80 80 % 7 P-70 70 % 6 P-60 60 % 5 P-50 50 % 4 P-40 40 % 3 P-30 30 % 2 P-20 20 % 1 P-10 10 % 0 P-10 0 %
9
When the oven is first plugged in, the display will flash “ :0” and a tone will sound. If the AC power ever goes off, the display will flash “ :0” when the power comes back on.
CONTROLS
SETTING THE CLOCK
DO THIS...
1. Touch CLOCK/A.START pad.
2. Touch
CLOCK/A.START pad
once more.
3. Enter the correct time of day by touching the numbers in sequence.
4. Touch
CLOCK/A.START pad.
THIS HAPPENS...
This is a 12 hour clock system.
This is a 24 hour clock system.
The display will then begin blinking.
CLOCK /
A. ST ART
0321
CLOCK /
A. ST ART
CLOCK /
A. ST ART
NOTE :
This oven is multiple clock system. If you want 12 hour clock system, can be omitted this step.
The display stop blinking, and the colon starts blinking. If you selected 12 hour clock system, this digital clock allows you to set from 1:00 to 12:59. If you selected 24 hour clock system, this digital clock allows you to set from 0:00 to 23:59.
NOTE : If you attempt to enter an incorrect time, the time will not be set and a error signal tone will sound. Touch the
CLOCK/A.START pad re-enter the time.
10
WEIGHT DEFROST lets you easily defrost food by eliminating guesswork in determining defrosting time. The minimum weight for WEIGHT DEFROST is 200 grams. The maximum weight for WEIGHT DEFROST is 3000 grams. Follow the steps below for easy defrosting.
WEIGHT DEFROSTING
DO THIS...
1. Touch AUTO DEFROST pad.
2. Touch number pads for the defrosting weight you want.
3. Touch
START pad.
THIS HAPPENS...
The WEIGHT DEFROST indicator lights and “0” is displayed. And the “g” indicator starts blinking.
The display will show the numbers you pressed in the order you touched.
ST ART
005
AUTO
DEFROST
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
WEIGHT DEFROSTING begins. The defrosting time is automatically determined by the food category and weight entered. The “g” indicator goes off and the WEIGHT DEFROST indicator blinks and the defrosting time counts down in the display window. The oven beeps during the defrosting cycle to signal that the food needs to be turned or rearranged. When the defrosting time ends, you will hear 3 beeps.
NOTE : To prevent overdefrosting, thin areas or edges can be shielded with strips of aluminum foil.
11
When TIME DEFROST is selected, the automatic cycle divides the defrosting time into periods of alternating defrost and stand times by cycling on and off.
DO THIS...
1. Touch AUTO DEFROST pad.
2. Touch
AUTO DEFROST pad
once more.
3. Touch number pads for the defrosting time you want.
4. Touch
START pad.
THIS HAPPENS...
ST ART
0172
AUTO
DEFROST
AUTO
DEFROST
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
When you touch START pad, the TIME DEFROST indicator starts blinking to show
the oven is in the TIME DEFROST mode. The display counts down the time to show you how much defrosting time is left in the TIME DEFROST mode. The oven beeps during the defrosting cycle to signal that the food needs to be turned or rearranged. When the defrosting time ends, you will hear 3 beeps.
NOTE :
Your oven can be programmed for 99 minutes 99 seconds. (99:99)
NOTE : To prevent overdefrosting, thin areas or edges can be shielded with strips of aluminum foil.
TIME DEFROSTING
12
DO THIS...
1. Touch POWER pad.
2. Touch the number pad for the power level you want.
3. Touch number pads for the cooking time.
4. Touch
START pad.
THIS HAPPENS...
The STAGE1 indicator lights and “P-” is displayed.
The display will show what you touched. This example shows power level 3.
The display will show the numbers you pressed in the order you touched.
ST ART
035
3
POWER
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
When you touch START pad, the STAGE 1 indicator starts blinking to show the oven is cooking. The display counts down the time to show how much cooking time is left. When the cooking time ends, you will hear 3 beeps.
NOTE :
If steps 1 and 2 are omitted, the oven will cook at full power.
NOTE :
Your oven can be programmed for 99 minutes 99 seconds. (99:99)
NOTE : Using lower power levels increase the cooking time which is recommended for foods such as cheese, milk
and slow cooking of meats.
COOKING IN ONE ST AGE
13
For best results, some recipes call for one power level for a certain length of time and another power level for a different length of time. Your microwave oven can be set to change from one to another.
DO THIS...
1. Touch number pads for the cooking time you want in the first stage.
2. Touch
POWER pad.
3. Touch the number pads for the power level you want in second stage.
4. Touch the number pads for the cooking time you want in the second stage.
5. Touch
START pad.
THIS HAPPENS...
The STAGE 1 indicator lights and the display will show the numbers you pressed in the order you touched. This example shows 5 minutes 30 seconds at full power.
The STAGE 2 indicator lights and “P-” is displayed.
The display will show what you touched.
The display will show the numbers you pressed in the order you touched. This example shows 4 minutes 20 seconds at power level 8.
ST ART
024
8
POWER
035
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
When you touch START pad, both STAGE 1 & 2 indicator lights come on, STAGE1 indicator light starts blinking to show you that the over is cooking in the first of two cook stages. The oven will cook at the power you selected for stage one. At the end of stage one, the oven will beep and start stage two, the STAGE 1 indicator goes off and the STAGE 2 indicator starts blinking. The display counts down the time
remaining in stage two when stage two ends, you will hear 3 beeps.
COOKING IN TWO ST AGES
14
Some recipes require frozen foods to be thawed before cooking. This oven can be programmed to automatically defrost foods before cooking.
DO THIS...
1. Touch AUTO DEFROST pad.
2. Touch number pads for the defrosting weight you want.
3. Touch
POWER pad.
4. Touch
POWER pad once
more.
5. Touch number pads for the cooking time you want in the first stage.
THIS HAPPENS...
The WEIGHT DEFROST indicator lights and “0” is displayed. And the “g” indicator starts blinking.
The display will show the numbers you pressed in the order you touched.
The STAGE 1 indicator lights and “P-” is displayed.
“P-HI” will appear in the displayed. This example shows full power (100%).
The display will show the numbers you pressed in the order you touched. This example shows 5 minutes 30 seconds at full power.
035
POWER
POWER
005
AUTO
DEFROST
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
WEIGHT DEFROSTING AND COOKING IN TWO ST AGES
15
DO THIS...
6. Touch POWER pad.
7. Touch the number pads for the power level you want in the second stage.
8. Touch the number pads for the cooking time you want in the second stage.
9. Touch
START pad.
THIS HAPPENS...
The STAGE2 indicator lights and “P-” is displayed.
The display will show what you touched.
The display will show the numbers you pressed in the order you touched. This example shows 4 minutes 20 seconds at power level 8.
ST ART
024
8
POWER
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
LOCK NO CUPS g
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
When you touch START pad, the WEIGHT DEFROST, STAGE 1 and STAGE 2 indicators come on to confirm the power levels selected. The WEIGHT DEFROST indicator starts blinking to show you that the oven is in WEIGHT DEFROST mode.
The display counts down the time remaining in WEIGHT DEFROST mode. Turn over, break a part and redistribute at a beep. At the end of WEIGHT DEFROST mode, the oven will beep and start stage one. The WEIGHT DEFROST indicator goes off and the STAGE 1 indicator starts blinking. The display counts down the time remaining in stage one. At the end of stage one, the oven will beep and start stage two. The STAGE 1 indicator goes off and the STAGE 2 indicator starts blinking. The display counts down the time remaining in stage two when stage two ends, you will hear 3 beeps.
16
Allows you to program cooking to start at a time you select. The food will automatically start cooking at the desired time. Program is able up to 2 stages (not acceptable DEFROST)
DO THIS...
2. Touch CLOCK/A.START pad.
3. Enter the desired start time by pressing the number pads.
4. Touch
START pad.
THIS HAPPENS...
The AUTO START indicator lights and “ :0” is displayed.
The display will show the numbers you pressed in the order you touched. This example shows 11:30
ST ART
0311
CLOCK/
A.ST ART
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
When you touch START pad, the present time appears in the display and the cooking program indicators come on. The AUTO START indicator and the colon start blinking. When the selected start time arrives the oven begins operating and the oven light turns on. The AUTO START indicator goes off and the next stage indicator begins to blink. When the cooking is completed you will hear 3 beeps. The oven turns off and the present time appears in the display.
1. Program the desired power level and cooking time.
NOTE : AUTO START can be used for time cooking, if clock is set. If the oven door is opened after programming
AUTO START, it is necessary to touch the START pad for the time of day to appear in the readout so that the oven will automatically begin programmed cooking at the chosen AUTO START time. Before setting, check to make sure the clock is showing the correct time of day.
AUTO START
17
Once you have correctly programmed the oven for AUTO START, the present time will appear on the display.
SPEEDY COOK, allows you to reheat for 30 seconds at 100% (full power) by simply touching the SPEEDY COOK pad. By repeatedly touching the SPEEDY COOK pad, you can also extend reheating time to 5 minutes by 30 seconds.
TO CHECK AUT O START TIME
SPEEDY COOK
DO THIS... THIS HAPPENS...
1. Touch CLOCK/A.START pad.
CLOCK/
A.ST ART
The programmed AUTO START time will appear on the display for 3 seconds.
DO THIS...
1. Touch SPEEDY COOK pad.
THIS HAPPENS...
When you touch SPEEDY COOK, “ :30” is displayed. After 1.5 seconds, the oven starts reheating.
SPEEDY
COOK
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
18
One touch cook allows you to cook or reheat many of your favorite foods by touching just one pad. To increase quantity, touch chosen pad until number in display is same as desired quantity to cook. (except for MUFFIN & DINNER PLATE)
ONE TOUCH COOKING
DO THIS...
1. Touch POPCORN pad.
THIS HAPPENS...
When you touch POPCORN pad, “99” is displayed. After the 1.5 seconds, the display changed, into cooking time of quantity and the oven starts cooking.
POPCORN
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
* POPCORN*
• 99g : Touch POPCORN once.
• 50g : Touch POPCORN twice within 1.5 seconds.
NOTE : 1. Use prepackaged room-temperature microwave popcorn.
2. Place bag in oven according to manufacturer’s directions.
3. Pop only one bag at a time.
4. After popping, open bag carefully, popcorn and steam are extremely hot.
5. Do not reheat unpopped kernels or reuse bag.
6. Do not leave oven unattended while popping popcorn.
CAUTION : If pre-packaged popcorn is of a different weight than the recommended weight, do not use the popcorn
setting, or inadequate popping or a fire may occur. Follow the manufacturer’s instructions.
KOR-145Q0S KOR-145M0S POPCORN POPCORN
FROZEN PIZZA FROZEN PIZZA BEVERAGE BEVERAGE
ONE TOUCH COOKING DINNER PLATE DINNER PLATE
MUFFIN MUFFIN SOUP ­FRESH VEGETABLE ­BAKED POTATO -
19
DO THIS...
1. Touch BEVERAGE pad.
THIS HAPPENS...
When you touch BEVERAGE pad, “1” is displayed. After 1.5 seconds, the display changed into cooking time of quantity and the oven starts cooking.
BEVERAGE
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
* FROZEN PIZZA*
• 200g : Touch FROZEN PIZZA once.
• 300g : Touch FROZEN PIZZA twice within 1.5 seconds.
NOTE : 1. Use only one frozen pizza at a time.
2. Use only frozen pizza for microwave oven.
3. If the cheese of frozen pizza does not melt sufficiently, cook a few seconds longer.
4. Some brands of frozen pizza may require more or less cooking time.
* BEVERAGE* (250ml/cup)
• 1 cup (mug) : Touch BEVERAGE once.
• 2 cups (mugs) : Touch BEVERAGE twice within 1.5 seconds.
• 3 cups (mugs) : Touch BEVERAGE three tmes within 1.5 seconds.
NOTE : 1. This setting is good for restoring cooled beverage to a better drinking temperature.
2. Stir after cooking.
DO THIS...
1. Touch FROZEN PIZZA pad.
THIS HAPPENS...
When you touch FROZEN PIZZA, “200” is displayed. After 1.5 seconds, the display changed into cooking time of quantity and the oven starts cooking.
FROZEN
PIZZA
STAGE DEFROST
1 2 WEIGHT TIME
AUTO
START
LOCK NO CUPS g
Loading...
+ 43 hidden pages