Daewoo GTV110PANR User Manual

FEATURE CHART

!ICE TRAY

@FREEZER SHELF (MOVABLE)

#FREEZER TEMPERATURE CONTROL SWITCH

$ICE BOX

%CHILLED CASE DOOR

^CHILLED CASE

&REFRIGERATOR TEMPERATURE CONTROL KNOB

*REFRIGERATOR SHELF (MOVABLE)

(LAMP COVER

)VEGETABLE CASE COVER

1VEGETABLE CASE

2FREEZER POCKET(SMALL)

3FREEZER POCKET(MIDDLE)

4EGG CASE

5UTILITY POCKET(SMALL/LARGE)

6UTILITY POCKET(SMALL/SMALL)

7BOTTLE POCKET(LARGE/LARGE)

8BOTTLE POCKET(MIDDLE/LARGE)

2

Here are the features of your new refrigerator.

Take a moment to know all the features designed for your convenience.

■Ice Tray

Fill 3/4 of the ice tray with water, as the volume expands when the water is frozen. Place the tray in the freezer compartment. To release ice cubes, twist the ice tray slightly. Ice cubes will be easier to remove if it is held for a short while under running water.

■Movable refrigerator and freezer shelves

Storage shelves should be adjusted depending on the height of the food stored. To do this, pull the shelves slightly forward.

■ Lamp cover

To remove the lamp cover

1. Push up the bottom end of lamp cover gently, then pull out.

2. Reverse procedure to join together.

■ Vegetable case

May be used for fruit and vegetable storage. Both the vegetable case and its cover shelf are removable for easy cleaning. Simply slide forward to remove.

■ Utility Pocket (Top)

The Egg Case in this pocket can be turned upside down for the storage of small size food.

CAUTION

1.Check your voltage before inserting the power supply cord into the socket.

2.Contact the earthing conductor to this unit with an attachment earthing screw.

3.Do not spill liquid on this unit.

4.Do not use flammable spray, such as painting, near this unit.

5.Do not place ignitable material, such as benzine, L.P. gas, alcohol etc., into this unit.

6.Take precautions against leakage of any gas equipment near this unit.

7.Keep children from hanging on the door of this unit.

8.Do not reinsert the power supply cord within 5 minutes after releasing it from the socket. If not, there may be problems with the compressor.

3

4

METHODS OF SAFE INSTALLATION

1. SAFE INSTALLATION PLACE FOR YOUR REFRIGERATOR

•Place the refrigerator on a strong and level floor. Unstable installation can produce noise and vibration.

•Place your refrigerator where there is no heat source nearby.

High atmosphere temperature will lower cooling efficiency and increase your electricity bill.

•Place the refrigerator in an area where the humidity level is low. Splashing water on the refrigerator or installing the unit in a humid area may cause short circuit and rust.

2. INSTALLATION STEPS

•Select a safe place to	•Level the refrigerator by	•Install the parts in their
	using the adjustable feet.	own place.

C
om
ponents		to their
original
	places

•Avoid places that are exposed to coal gas or smoke, or discoloring may occur on the

•For good ventilation, keep enough space between the sidewalls and your.

This helps to cool efficiently and lowers the electricity bill.

•Putting the refrigerator	•Check if the doors are	•Check the voltage.
on the carpet may cause		Then wait about an hour
temperature rise and		before plugging the
result in the discoloring		power cord into the
of the carpet due to the
		outlet.
compressor heat.
In such a case, place a
hard wooden board or a
rubber mat between the
carpet and the unit.
		Plug in after
		about hour

Carpet

Check

Wooden Board,

Rubber Mat

•Put food in the refrigerator after running the refrigerator for 2~3 hours.

		after
Put	food
		hours
2~3

5

6