Daewoo FRA-X22D, FRA-X22B, DRX32DDL User Manual
User Guide Manual
FRA-X22B..
FRA-X22D..
DRX32DDL..
Code : X603-5
Disposal of Used Electrical &
Electronic Equipment
The meaning of the symbol on the product, its
accessory or packaging indicates that this product
shall not be treated as household waste. Please,
dispose of this equipment at your applicable
collection point for the recycling of electrical &
electronic equipments waste.
In the European Union and Other European countries
there are separate collection systems for used electrical
and electronic product. By ensuring the correct disposal of
this product, you will help prevent potential hazards to the
environment and to human health, which could otherwise
be caused by unsuitable waste handling of this product.
The recycling of materials will help conserve natural
resources.
Please do not therefore dispose of your old electrical and
electronic equipment with your household waste.
For more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where you
purchased the product.
SAFETY WARNING
(R-600a Models Only)
This appliance contains a certain amount of
isobutane refrigerant (R600a) a natural gas
with high environmental compatibility that is,
however, also combustible.
When transporting and installing the appliance, care
should be taken to ensure that no parts of the
refrigerating circuit are damaged.
Refrigerant squirting out of the pipes could ignite or
cause eye injury. If a leak is detected, avoid any naked
flames or potential sources of ignition and air the room
in which appliance is standing for several minutes.
ⰒIn order to avoid the creation of a flammable gas-air
mixture if a leak in the refrigerating circuit occurs, the size
of the room in which the appliance may be sited depends
on the amount of refrigerant used.
The room must be 1 m³ in size for every 8g of R600a
refrigrant inside the appliance. The amount of refrigerant
is shown on the identification plate inside the appliance.
ⰒNever start up an appliance showing any signs of
damage. lf in doubt, consult your dealer.
OBSERVE AMBIENT TEMPERATURE
This refrigerator is designed to operate in ambient
temperature specified by its category, which is marked on
the rating plate
Climatic category Ambient temperature from...to
SN + 10 to + 32
N + 16 to + 32
ST + 16 to + 38
T + 16 to + 43
NOTE
Internal temperature may be affected by such factors as
the location of the refrigerator, ambient temperature and
frequency of the door opening.
Contents
Be sure to keep for safety ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ1~2
Installation GuideⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ2
Control Panel ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ3
Temperature Control ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ4
How to use Interior Parts ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ5~6
How to use the Dispenser ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ7
How to use the Automatic IcemakerⰒⰒⰒⰒⰒⰒⰒⰒ7
Care & Cleaning ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ8
Before You Call for Service... ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ9
Something strange?
Don’t worry. Here is the answer ⰒⰒⰒⰒⰒⰒⰒⰒⰒ10
Installation Preparation ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ11
If the refrigerator can not pass through a door
during installation, follow these steps ⰒⰒⰒⰒⰒⰒⰒ11
Refrigerator Leveling &
Door Adjustment (if needed) ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ13
How to install Water Line ⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒⰒ14
RoHS (Directive 2002/95/EC) Compliant
This product is environmentally sound and
sustainable free from Pb, Cd, Cr+6, Hg, PBBs
and PBDEs restricted in accordance with the
Directive.
Be sure to keep for safety!
Read these safety instructions thoroughly and carefully
before using. Please keep this user guide on hand for future
reference.
Be sure to ground. Check if your wall outlet
is grounded (earthed).
There is a risk of electric shock hazards.
Never unplug by pulling only the power cord
wire. Always grip the plug firmly.
Indicates the possibility of danger of
death or serious injury.
Indicates the possibility of risk of personal
injury or material damage.
Other Signs
DO NOT remove or disassemble!
Be sure to unplug from outlet/mains!
NO. DO NOT...
Be sure to keep and follow!
Caution
1. If the supply cord becomes damaged, it must be replaced
by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
2. This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
WARNING
Never let the power cord be crushed
by the refrigerator itself or other (heavy)
objects. Never bend power cord excessively.
If the cord is damaged or peeled, it can be a
cause of fire and electric shock.
Do not plug several appliances into the
same wall outlet.
It can be a cause of overheating and/or fire.
Use an exclusive grounding receptacle for
the refrigerator.
Never hold the power cord or plug with wet
hands.
There is a risk of electric shock.
Never use a damaged power cord or plug,
or loose main socket.
There is a risk of fire, electric shock or
serious injury.
Let the cord from the plug outlet be
directed downwards.
If it is directed up, the cord near the plug is
bent and can be damaged, which can
cause an electric shock or fire.
Do not install the refrigerator on a wet
floor or in a place with excessive humidity and
moisture.
Electric insulation gets weakened,
resulting in a risk of electric shock
hazards.
Never let the power cord touch or pass over
heating appliances.
Power cord can be damaged, resulting in a
risk of electric shock hazards.
Check if plug is loose from the wall outlet.
Electric insulation gets weakened,
resulting in a risk of electric shock
hazards.
Never pour or spray water into the
refrigerator (both interior and exterior).
Electric insulation gets weakened, resulting
in a risk of electric shock hazards.
Do not place containers with water or
liquid on top of refrigerator.
Water can spill into the refrigerator
and can cause electric shock hazards or
damage.
Do not let children hang on the refrigerator
doors.
Refrigerator can fall and harm them.
Do not move or remove compartment
shelves/pockets while foods and
containers are on them.
Hard containers (of glass, metal etc.) can
fall to hurt you and can break glass shelf
and interior parts.
Never repair or disassemble or amend the
refrigerator on your own
There is a risk of personal injury or damage
to the refrigerator. It is recommended that
any service be carried out by a qualified
person.
1
Never store any flammable gas or liquid
in the refrigerator.
Never use flammable gas, benzene, thinners,
gasoline, spray etc. near the refrigerator.
There is a risk of fire, explosion and
personal injury or damage.
If a gas leak is found near the refrigerator
or in the kitchen, ventilate it immediately
without touching the power plug or
refrigerator.
Do not store medicine or academic research
samples which require strict temperature
control in the refrigerator.
Never insert fingers or hands into the bottom
of the refrigerator, especially into the bottom
at the back.
You can be hurt by sharp metal edges or can
receive an electric shock.
Do not change fuse or LED lamp on your own.
Call the service agent to change them.
When you find the power cord damaged or
cut, call the service agent immediately.
CAUTION
Be sure to unplug the refrigerator when it is
not going to be used for a long time.
Never touch foods and containers
especially of metal with wet hands in the
freezer compartment.
You can be hurt by chilblains or cold burns.
Never eat any decayed or deteriorated food at all.
Foods stored too long in the refrigerator can
deteriorate and become decayed.
Never place bottles and containers of glass
in the freezer compartment.
Glass containers and bottles can break and
can hurt you.
When moving the refrigerator (horizontally
or tilted), more than 2 people are required
to hold it.
(One to hold top back handles, the other to hold
the bottom holder.)
If other parts are held instead, it is very dangerous
and likely to slip.
When you get rid of your old refrigerator, be
sure to remove the door packings first.
Children can be entrapped and suffocated in
an abandoned refrigerator.
Keep ventilation openings, in the appliance
enclosure or in the built-in structure,
clear of obstruction.
Do not use mechanical devices or other means to
accelerate the defrosting process.
Do not use electrical appliances inside the food
storage compartments of the appliance.
The ice-maker in the freezer can be only replaced
by the manufacturer or the service agent.
When the freezer door is open, do not press the
dispenser lever.
Connect to drinkable water supply only.
Be sure to turn up the wheel first before
moving the refrigerator.
The wheels can damage or scratch the floor.
If you are moving it for a long distance, never forget
to fasten the interior parts tightly with tapes.
Otherwise, the parts can collide and break each
other.
Installation Guide
↜ Read these safety instructions carefully before use and
follow precautions for your safety.
Precautions in installation and
power connection
¥To prevent fire, electric shock or leakage.
⇡Never install the refrigerator on a wet, watery floor or
where water can gather easily.
⇢Check the following before power connection.
Connect power plug only to a grounded wall socket
(an earthed mains).
Do not plug refrigerator power together with other
appliances to the same socket.
⇣Do not use an adapter plug or an extension cord.
2
⇤Do not let the power cor
(heavy) objects .
If you hear a strange noise, strong chemical odour
or find smoke etc. from the refrigerator after the power
is plugged in, pull out the plug immediately and call
the service agent.
Wait about 5 minutes before you plug-in again in
order to prevent any damage to the compressor and
electrical devices of refrigerator.
Wait 2~3 hours until the inside gets cold enough after
the first power plug-in, then store foods inside.
(There can be some smell of plastic parts on initial
operation of the refrigerator after plugging in.
The smell fades away as the refrigerator works and
doors are opened and closed.)
d be crushed by other
Precautions in use
2. LIGHT/FILTER button
1) Button for dispenser light on.
2) Button for filter exchange or reset.
After exchanging or to reset press the button
for 3 seconds.
3. Displays the button 'Lock'.
4. Filter exchange display
After 6 months of first power input, the icon will
flicker.
5. Button for water dispensing. Water symbol lights up
when selected.
6. Selection button for ice dispensing and lock for ice
maker.
¥To prevent personal injury, fire, electric shock etc. read
this user guide carefully before use and keep it at
hand for any reference.
¥Accessories
Filter box Water supply kit User guide manul
Control Panel
£ Dispenser Model
1. FRZ.SET button
Selection button for freezer compartment
temperature.
7. REF.SET button
Selection button for refrigerator compartment
temperature.
8. Lock button for control panel
Press button for more than 3 seconds to activate
and prevent settings from being unintentionally
changed. To release the button, press for longer
than 3 seconds. The display goes out.
£ Non Dispenser Model
1. Displays the button 'Lock'.
2. FRZ.SET button
Selection button for freezer compartment
temperature.
3. REF.SET button
Selection button for refrigerator compartment
temperature.
Note
Interior lights of the refrigerator turn off when the doors are open for more than 10 minutes.
In case either the freezer or refrigerator door is left open for more than a minute, door alarm rings for 5 minutes with
1 minute intervals.
Display off function
- 5 minutes after no buttons or doors are operated by customer, all the display LED except for water, ice and ice lock icon
go out.
- Under the LED off status, it returns to normal display mode when customers operate buttons or doors.
System off function (power off function)
- You can stop operating the appliance without unplugging especially on holidays.
- Pressing FRZ.SET and REF.SET button at the same time for 5 seconds will turn the appliance off.
- Under the ‘off’ mode, freezer and refrigerator temperature displays “-- --”.
- Other LED lights go out and all the operation of your appliance halt.
- Conversely, pressing FRZ.SET and REF.SET button together for 5 seconds will switch it back on.
3
4. Lock button for control panel
Press button for more than 3 seconds to activate
and prevent settings from being unintentionally
changed. To release the button, press for longer
than 3 seconds. The display goes out.
£ Non Dispenser Model
Temperature Control
↜When this refrigerator is first plugged in, the temperature
mode is set to [Middle].
£ Dispenser Model
Freezer Compartment
Push the FRZ. SET button and the setting temperature
changes as the figure shows.
>>> Sequential Temperature Change <<<
Faster Freezing...
When you want faster freezing, push the FRZ.SET button,
until ' ' LED turns on. Just push the button again to
release.
Refrigerator Compartment
Push the REF. SET button and the setting temperature
changes as the figure shows.
>>> Sequential Temperature Change <<<
Freezer Compartment
Push the FRZ. SET button and the setting temperature
changes as the figure shows.
>>> Sequential Temperature Change <<<
Faster Freezing...
When you want faster freezing, push the FRZ.SET button,
until ' ' LED turns on. Just push the button again to
release.
Refrigerator Compartment
Push the REF. SET button and the setting temperature
changes as the figure shows.
>>> Sequential Temperature Change <<<
Faster Cooling or
Refrigeration
When you want faster cooling or refrigeration , push the
REF.SET button, until ' ' LED turns on. Just push the
button again to release.
Caution
Foods in the refrigerator can be frozen if the
ambient temperature of the refrigerator is below 5°c.
Faster Cooling or
Refrigeration
When you want faster cooling or refrigeration , push the
REF.SET button, until ' ' LED turns on. Just push the
button again to release.
Temperature indicator convert function
Note
4
(Fahrenheit ® Celsius)
Press the lock button to enter locked mode.
Under the locked mode, press the light and
water button at the same time for 10 sec to
swap temperature scale (default setting is
celsius).
Loading...