Daewoo F109A1 User Manual

NEXT

Type No. L19C0D060

User’s Guide

Daewoo Computer F109A1

Dual Function Monitior

U.S.A.

U.S.FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
INFORMATION TO THE USER

NOTE : This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet of a circuit different from that to which

the receiver is connected.

Consult the dealer or an experienced radio/TV technician for assistance.

Changes or modification not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Connecting of peripherals requires the use of grounded shielded signal cables.

BACK

NEXT

F109A1

19" Dual Function Monitor

Contents

1. Introduction ...................................1/22

2. Safety Information ........................1/22

3. Installing the monitor ...................4/22

3-1. Packing List .........................................4/22

3-2. Selecting a suitable location ..............5/22

3-3. Connecting the monitor .....................5/22

3-4. Setting the refresh rate ......................8/22

Preset Timing Table ............................8/22

3-5. User’s Environment ...........................10/22

BACK

NEXT

4. Adjusting the picture ..................12/22

4-1. Using the On Screen Display ...........14/22

4-2. Direct access buttons .......................14/22

4-3. OSD Adjustments .............................15/22

5. Display power management ......18/22

Reducing power consumption ..............18/22

6. Troubleshooting ..........................19/22

7. Specifications ..............................22/22

F109A1

19" Dual Function Monitor

1. Introduction

2. Safety Information

1/22

BACK

NEXT

This manual contains instructions for installing and operating Daewoo Computer
F109A1.

Daewoo Computer F109A1 is a highly ergonomic color display unit.

• 19" viewable SXGA LCD

• High quality screen re-scaling capability

• 100-240V AC input voltage

• VESA DPMS (Display Power Management Signaling)

• VESA DDC1/2B compatibility

• Advanced digital On-Screen-Display controls

• Fast and accurate auto adjustment

• Most advanced image scaling

• Supporting VESA Flat Panel Monitor Physical Mounting Interface

This Monitor has been engineered and manufactured to assure your safety.
You can prevent serious electrical shock and other hazards by keeping in mind
the following:

Do not place anything wet on the monitor or the power
cord. Never cover the ventilation openings with any
material and never touch them with metallic or
inflammable materials.

F109A1

19" Dual Function Monitor

2/22

BACK

NEXT

Avoid operating the monitor in extreme heat,
humidity or areas affected by dust.
Temperature : 5~35°C
Humidity : 30~80RH

Be sure to turn the monitor off before plugging the
power cord into the socket. Make sure that the power
cord and the other cords are securely and rightly
connected.

Overloaded AC outlets and extension cords are
dangerous, as are frayed power cords and broken
plugs, which may cause electric shock or fire. Call
your service technician for replacement.

Do not use sharp tools such as a pin or a pencil near
the monitor, as they may scratch the LCD surface.

Do not use a solvent, such as benzene, to clean the
monitor, as it will damage the LCD surface.

F109A1

19" Dual Function Monitor

Cleaning and Maintenance

• To avoid risk of electric shock, do not disassemble the display unit cabinet. The
unit is not user-serviceable. Remember to unplug the display unit from the
power outlet before cleaning.

• Do not use alcohol (methyl, ethyl or isopropyl) or any strong dissolvent. Do not
use thinner or benzene, abrasive cleaners or compressed air.

• Do not wipe the screen with a cloth or sponge that could scratch the surface.

• To clean your antistatic screen, use water and a special microfiber screen
cleaning tissue used in optical lens cleaning, or lightly dampen a soft, clean
cloth with water or a mild detergent.

• If the instructions above do not help in removing stains, contact an authorized
service agent.

3/22

BACK

NEXT

F109A1

19" Dual Function Monitor

4/22

BACK

NEXT

The following items should be found in the packaging.

Above power cord can be changed upon different voltage areas. Please
contact your dealer if anything is missing or damaged.

Other power cord except the cord packed in the product or longer than 3m
may affect EMC of the product in operating condition.

3. Installing the
monitor

3-1. Packing List

!

Power Cord

Signal Cable

DVI-D Cable

Compact Disc

Audio Cable

F109A1

19" Dual Function Monitor

5/22

BACK

NEXT

3-2. Selecting a suitable

location

3-3. Connecting the

monitor

• 15 pin D-sub / DVI-D

• Place the monitor at least 30cm from other electrical or heat-emitting
equipment and allow at least 10cm on each side for ventilation.

• Place the monitor in a position where no light shines directly onto or is
reflected on the screen.

• To reduce eye strain, avoid installing the display unit against a bright
background such as a window.

• Position the monitor so that the top of the screen is no higher than eye level.

• Position the monitor directly in front of you at a comfortable reading distance
(around 45 to 90cm)

Before you start cabling your monitor, check that the
power is off on all units. To avoid any possibility of
electric shock, always connect your equipment to
properly earthed outlets.

1. Insert the other 15-pin/DVI-D signal cable connector into the 15-pin VGA/DVI-D
connection on your computer and screw it down.

2. Plug the power cord connection to connection on the monitor.

3. Plug the other end of the power cord to your computer's main supply or to a
100V-240V earthed electrical outlet.

4. Turn on the monitor using the power switch and check that the power LED is
on. If not, repeat steps 1,2,3 and 4 or refer to the Troubleshooting section of
this guide.

!!

F109A1

19" Dual Function Monitor

6/22

BACK

NEXT

5. Turn on the power to the computer. The picture will appear within about 10
seconds. Adjust the picture to obtain optimum picture quality. See section
Adjusting the picture in this guide for more information.

15 pin D-sub cable (Analog RGB)

DVI-D cable (Digital TMDS)

F109A1

19" Dual Function Monitor

• Audio system

7/22

BACK

NEXT

!!

This monitor has an audio system including two micro loudspeakers. Each of two
micro loudspeakers has an 2Wrms (typ.) output power. This system also supports a
headphone output jack.

This system has been tuned to get a best tone quality which an audio input
level is under 300mVrms. if the input level is more than 600mVp-p, you must
tune down the audio input as the audio output tone may be distorted.

When this monitor is turned on, audio is always set up as off mode. Please use
AUDIO direct access button on the front cover or On Screen Display to put
audio on.

Power Switch

Speaker

F109A1

19" Dual Function Monitor

8/22

BACK

NEXT

3-4. Setting the refresh

rate

Preset Timing Table

Follow the instructions below to set your refresh rate in Windows 98/ME/XP/2000.

1. Go to the configuration window(Start-Settings-Configuration window).

2. Double click on the ‘Display’ icon.

3. Click on the ‘Settings’ tab.

4. Click on the ‘Advanced’ button.

5. Click on ‘Adapter’ and select 60Hz from the list.

6. Click on ‘Apply’ to accept the selected value.

If the signal from the system doesn't equal to the preset timing mode, adjust
the mode with reference to the user guide of videocard because the screen
may not be displayed.

DIGITAL R.G.B INPUT

No.

1
2
3
4

Resolution

640

x

480

800

x

600

1024

x

768

1280

x

1024

Horizontal Frequency

31.5 KHz

37.9 KHz

48.4 KHz

63.9 KHz

Refresh rate

60 Hz
60 Hz
60 Hz
60 Hz

!

F109A1

19" Dual Function Monitor

Preset Timing Table

The recommended setting is a resolution of 1280x1024 and a refresh rate of 60Hz.

9/22

BACK

NEXT

No.

1
2
3
4
5
6
7
8
9

10
11
12
13
14

Resolution

720

x

400

640

x

480

640

x

480

800

x

600

800

x

600

800

x

600

800

x

600

832

x

624

1024

x

768

1024

x

768

1024

x

768

1152

x

864

1280

x

1024

1280

x

1024

Horizontal Frequency

31.5 KHz

31.5 KHz

37.5 KHz

35.2 KHz

37.9 KHz

48.1 KHz

46.9 KHz

49.7 KHz

48.4 KHz

56.5 KHz

60.0 KHz

67.5 KHz

63.9 KHz

80.0 KHz

Refresh rate

70 Hz
60 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
75 Hz
60 Hz
70 Hz
75 Hz
75 Hz
60 Hz
75 Hz

ANALOG R.G.B INPUT

F109A1

19" Dual Function Monitor

3-5. User’s Environment

Kensington Security
(Locking) Slot

Recommended Ergonomic User’s Environment

• Viewing angle of the monitor should be between 0~20 degree.

• This display unit supports a Kensington-type security device to secure your
monitor. Kensington lock is not included.

• To purchase and install the Kensington locking device, please refer to the
following contact information.

* Kensington Technology Group

· Address : 2000 Alameda de las Pulgas 2F san mateo, California 94403-1289

· Tel : [phone] · Fax : [phone] · Web-site : www.kensington.com

10/22

BACK

NEXT

20

o

Kensington
security slot

F109A1

19" Dual Function Monitor

VESA MOUNT’G

• This display unit supports VESA FPMPMI standard for 75mmx75mm screw
mounting by giving 4 screw holes inside the base stand of the unit.

• For buying VESA Flat Panel Monitor Mounting Devices, please contact
following information.

* Ergotron, Inc.

· Address : Ergotron Europe Kuiperbergweg 50 1101 AG Amsterdam The Netherlands

· Tel : [phone] · Fax : [phone]· E-mail : [e-mail]

11/22

BACK

NEXT

Desk Mount

Wall Mount

F109A1

19" Dual Function Monitor

4. Adjusting the picture

12/22

BACK

NEXT

You can adjust the screen display by using the buttons located below the
screen.

1280x1024

H:63.9 V:60.0

BRIGHTNESSBRIGHTNESS

In case of applying

Analog RGB

Input

F109A1

19" Dual Function Monitor

13/22

BACK

NEXT

1280x1024

H:63.9 V:60.0

BRIGHTNESSBRIGHTNESS

In case of applying Digital TMDS Input

F109A1

19" Dual Function Monitor

14/22

BACK

NEXT

1. Push the MENU button to call the OSD to the screen. The resolution and
frequency are displayed at the top of the menu box for your information.

2. Push the or button to choose the item you want to adjust. The selected
item is highlighted.

3. Push the SELECT button to adjust the highlighted item.

4. Use the or button to adjust the selection.

5. Push the MENU button to return to the previous menu if you are in a submenu.

6. The display unit automatically saves the new settings in 1 second after your
last adjustments and the menu disappears. You can also push the MENU button
to make the menu disappear.

AUTO ADJUST

At first display a full screen such as Window's back ground.
Push the button SELECT(AUTO) to adjust the shape of screen
automatically.

VOLUME

Use the button to select the volume adjustment.
Adjust with or button.

AUDIO

Push the button to choose audio on or off.

4-1. Using the On Screen

Display

4-2. Direct access buttons

F109A1

19" Dual Function Monitor

15/22

BACK

NEXT

4-3. OSD Adjustments

The OSD adjustments available to you are listed below.

BRIGHTNESS

Adjust the brightness of the screen.

CONTRAST

Adjust the contrast of the screen.

COLOR CONTROL

Color temperature affects the tint of the image. With lower color
temperatures the image turns reddish and with higher temperatures
bluish.

There are three color settings available: Mode 1(a cool white), Mode 2(a
warm white) or USER. With the USER setting you can set individual values
for red, green and blue.

POSITION

H POSITION

Adjusts the horizontal position of the entire screen image.

V POSITION

Adjusts the vertical position of the entire screen image.

F109A1

19" Dual Function Monitor

16/22

BACK

NEXT

CLOCK PHASE

PHASE

Adjust the noise of the screen image.

CLOCK

Adjust the horizontal size of the entire screen image.

MISCELLANEOUS

RECALL

Recall the saved color data.

OSD TIMER

You can set the displayed time of OSD Menu window on the screen by
using this adjustment.

OSD POSITION

Adjust the OSD menu's horizontal or vertical position on the screen.

AUTO COLOR

Optimum color setting is auto programmed for user’s convenience.

LANGUAGE

You can select the language in which adjustment menus are displayed.
The following languages are available : English, French, German, Italian,
Spanish, Swedish, Finnish, Danish, Portuguese, Dutch and Japanese.

F109A1

19" Dual Function Monitor

AUDIO

VOLUME

Adjust the audio volume level.

AUDIO

This menu is used to choose audio on or off.

AUTO ADJUST

You can adjust the shape of screen automatically at the full screen
pattern.

INPUT SELECT

This menu used to choose the desired input signal source.
There are two available signal source.

• Analog R.G.B : 15 pin D-sub, Analog Signal

• Digital TMDS : 24 pin DVI-D, Digital Signal

In case of applying Digital TMDS Input, the functions of Color Control, Auto
Adjust, Position, Clock Phase, Auto Color are not supported.

17/22

BACK

NEXT

!

F109A1

19" Dual Function Monitor

If the power management function of your computer is enabled, your monitor
turns on and off automatically. You can control power management features from
your computer.

Your computer may have power management features which enable the computer
or monitor to enter a power saving mode when the system is idle. You can
reactivate the system by pressing any key or moving the mouse.

The power button does not disconnect the monitor from the mains. The only
way to isolate the monitor completely from the mains supply is to unplug the
mains cable.

18/22

BACK

NEXT

5. Display power
management

Reducing power
consumption

Power consumption

40 W

3.5 W
0 W

Mode

Normal

off

Unplugged

LED

Green

Orange

Not illuminated

!

F109A1

19" Dual Function Monitor

6. Troubleshooting

19/22

BACK

NEXT

Problem

Blank screen

Error message:

Video mode not
supported

The display does
not enter power
management
mode

Possible solution

If the power LED is not lit, push the Soft power switch or check the
AC cord to turn the monitor on. If the display unit is powered
through the computer, check that the computer is switched on.

The display unit might be in standby mode. Push one of the
keyboard keys. Check that the keyboard is properly connected to
the computer.

Check that the signal cable connector is properly connected and that
the connection pins are not bent or damaged. If the connector is
loose, tighten the connector's screws.

Check that the power cable is correctly connected to the display unit
and to the power outlet.

Check the resolution and the frequency on the video port of your
computer.

Compare these values with the data in the Preset Timing Table.

The video signal from the computer does not comply with VESA
DPMS standard. Either the computer or the graphics adapter is not
using the VESA DPMS power management function.

If your monitor is not functioning properly, you may be able to solve the problem
by following the suggestions below :

F109A1

19" Dual Function Monitor

20/22

BACK

NEXT

Possible solution

Check that the signal cable connector is properly connected and that
the connection pins are not bent or damaged. Try another color
temperature.

Adjust the picture characteristics as described in the section OSD

Adjustment(4-3).

A problem with your graphics adapter or display unit. Contact your
service representative.

Check that the display resolution and frequency from your PC or
graphic adapter is an available mode for your monitor.
In your PC, you can check through Control panel, Display, Settings.

If the setting is not correct, use your computer utility program to
change the display settings.

Check that the signal cabel connector is properly connected and that
the connection pins are not bent or damaged.
If the connector is loose, tighten the connector’s screws.
Check that the computer is switched on.

To enter a power saving mode. You can reactivate the system by
pressing any key or moving the mouse.

Problem

Color defects

Size, position,
shape or quality
unsatisfactory

Duplicated
images

Image is not
stable

Message :

No signal

The power LED is
a orange color

Possible solution

LED Indicator can be orange color on changing of video mode or
Input Signal.

Check the Resolution and the frequency on the video part of your
computer. Compare these values with the data in the Preset Timing
Table.

Problem

The power LED is
a orange color

F109A1

19" Dual Function Monitor

21/22

BACK

NEXT

Contacting service

If the above troubleshooting hints do not help you find a solution to the problem,
contact an authorized service agent. If the monitor is sent for service, use the
original package if possible.

Unplug the display unit from the power outlet and contact a service agent when:

• The monitor does not operate normally according to the operating instructions.

• The monitor exhibits a distinct change in performance.

• The monitor has been dropped or the cabinet has been damaged.

• The monitor has been exposed to rain, or water or liquid has been spilled onto
the monitor.

F109A1

19" Dual Function Monitor

22/22

BACK

19"viewable, Diagonal, A-Si TFT

0.294 x 0.294 mm
250cd/m

2

25msec

376.32 x 301.056 mm
16,7 milion colors
R.G.B Analog, Digital TMDS(DVI-D)
Horizontal : 31.0 to 80.0KHz, Vertical : 56 to 75Hz
135 MHz
1280 x 1024@75Hz
1280 x 1024@60Hz
100-240 VAC, 1.0A
40W
VESA DPMS
VESA DDC 1/2B
BRIGHTNESS, CONTRAST, COLOR CONTROL, POSITION,
CLOCK-PHASE, MISCELLANEOUS, LANGUAGE, AUDIO,
AUTO ADJUST, INPUT SELECT
2ch x 2watts / EarPhone Jack & Speaker
75 x 75 mm screw mounting
TCO, FCC Class B, CE,
cULus, TÜV-GS, ISO 13406-2
5 ~ 35O C

6.2Kg unpacked, 8.2Kg packed
420 X 441 X 185 mm

LCD

Pixel pitch

Brightness

Response Time

Display area

Number of color

Input signals

Frequency rate

Maximum bandwidth

Maximum resolution

Recommanded resolution

Input voltage
Power consumption
Power management

Plug & Play

OSD menu

Built in Speaker

VESA FPMPMI

Ergonomics,

Safety and EMC

Operating Temperature

Weight

Dimensions (W X H X D mm)

• Specification is subject to change without notice for performance improvement.

7. Specifications