Daewoo DWF-180MNP User Manual

INSTRUCTION MANUAL

■ First applying the Air Bubble Washing System in the world.

■ Applying One-Touch Operation System.

■ Realizing calm washing through the innovational low-noise

design.

■ Before operating this washer, please read this instruction

completely. Thank you

Model: DWF-180MNP

=

Full-Auto Electric Washing Machine

➣ Your washer is equipped with the

bubble generator that generates a

great deal of air bubble.

➣ The air bubbles knock the dirt out

of the clothes during wash and

they push up the heavy dirt tp

remove it during rinse.

➣ Because the double washing

method using both air bubble &

water current is applied to this

washer, wash efficiency is excellent

in comparison with the original

washer system.

The First Air Bubble Washing

System in the World

CONTENTS Page

PARTS AND FEATURES......................................................2

WASHER SAFETY.................................................................3

INSTALLATION INSTRUCTIONS.........................................4

ELECTRICAL REQUIREMENTS..........................................5

INLET HOSE CONNECTION................................................6

OPERATING YOUR WASHER.............................................7

THE FUNCTIONS OF THE CONTROL PANEL..................8

WASHING PROCEDURE AND COURSE SELECTION

.......9

GENERAL PROCEDURE FOR OPERATION...................11

CARING FOR YOUR WASHER..........................................12

HOW TO CLEAN THE FILTER............................................13

REMOVING STAINS.............................................................14

TROUBLE SHOOTING.........................................................15

SPECIFICATION....................................................................16

A NOTE TO YOU

Thank you for buying a DAEWOO appliance.

DAEWOO washers are easy to use, save time, and help you manage your home better.

This manual contains valuable information about how to operate and maintain your washer properly and safely.

Please read it carefully.

DWF-180MNP 01.3.26 9:41 PM ˘ ` 1

2

PARTS AND FEATURES

DRYTEN COVER UNDER WATER TAP ADAPTER INLET HOSE

HOSE DRAIN (FOR NON-PUMP) HOSE DRAIN CLAMPHOSE DRAIN (FOR PUMP) CONNECTOR INLET

UP

DRYTEN

The parts and features of your washer are illustrated on this page.

Become familiar with all parts and features before using your washer.

NOTE

•

The drawings in this book may vary from your washer model.

They are designed to show the different features of all models covered by this book,

Your model may not include all features.

• GROUND WIRE

In case of 3-wire

power cord, ground

wire will not be

provided

• POWER CORD

• HOSE DRAIN

• LINT FILTER

• COLD WATER TAP

After using the washer,

close the water tap

• DETERGENT CASE

• PULSATOR

• POWER SWITCH

• CONTROL PANEL

• BLEACH INLET

• HOT WATER TAP

After using the washer, close the water tap.

In case of the single valve model,

there is no hot water valve.

• ADJUSTABLE LEG

• SOFTENER INLET

B

U

B

B

L

E

W

A

S

H

I

N

G

M

A

C

H

I

N

E

W

A

S

H

S

P

A

R

Y

R

IN

S

E

R

I

N

S

E

S

P

I

N

F

U

Z

Z

Y

B

L

A

N

K

E

T

E

C

O

N

O

M

Y

W

O

O

L

W

A

T

E

R

L

E

V

E

L

R

E

S

.

C

O

U

R

S

E

P

R

O

C

E

S

S

S

T

A

R

T

H

O

L

D

P

O

W

E

R

S

O

A

K

R

E

M

A

I

N

M

I

N

.

H

O

T

C

O

L

D

W

A

S

H

T

E

M

P

.

W

A

S

H

T

E

M

P

.

WATER LEVEL

C

ON

TROL

O

N

L

Y

S

P

I

N

M

E

D

I

U

M

L

O

W

S

M

A

L

L

HIGH

ACCESSORIES (Full Option)

DWF-180MNP 01.3.26 9:41 PM ˘ ` 2

3

Read all instructions before using your washer

Save these instructions

Your safety is important to us.

To reduce the risk of fire, electrical shock, or injury when using your washer, follow

basic precautions including the following:

Understanding your responsibilities

• Do not wash items that are soiled with vegetable or cooking oil.

These items may contain some oil after laundering.

Due to the remaining oil, the fabric may smoke or catch fire by itself.

• Do not use chlorine bleach and ammonia or acid (Such as vinegar or rust remover) in the

same wash. Hazardous fumes can form.

• Unplug power supply cord before attempting to service your washer.

• Do not wash fiberglass materials.

Small particles can stick to fabrics and cause skin irritation.

• Do not use hot water that temperature is over 50°C (120°F).

It can cause a deformation of plastic parts.

• Do not spray water on the control panel and back cover of the washer.

It can cause a fire or an electric shock.

• Flammable fluids (dry-cleaning solvents,

kerosene, gasoline, etc.) should not be

used or stored in or near your washer .

Do not add flammable fluids to your wash

water. These substances give off vapors

that can create a fire hazard or explosion.

• Do not allow children to operate, play

with, or crawl on or inside your washer.

Supervise children closely when your

washer is used near them.

• After starting a cycle, do not reach into

the spin basket unless all motion stops.

• Do not tamper with the controls.

Please ...

• Have only a qualified person install, repair,

or replace parts on washer.

• Maintain washer properly.

• Protect washer from the weather and

keep it where the temperature will not fall

below freezing.

• Do not install the washer at a place of

extremely high humidity. It could cause an

Electrical shock or a short circuit.

• Connect washer to the correct outlet,

electrical supply, water supply, and drain.

• Ground washer properly.

WASHER SAFETY

DWF-180MNP 01.3.26 9:41 PM ˘ ` 3

4

Non-Pump Model Pump Model

Location of washer

Check location where washer will be installed. Make sure you have everything

necessary for correct installation.

Proper installation is your responsibility.

•Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.

•Install the washer on the horizontal solid floor.

Drain system

Never forget to install drain hose before operating your washer.

The packing box is opened, there are a drain hose.

INSTALLATION INSTRUCTIONS

• Connect the drain hose to the drain outlet

at the back side of the washer.

• Connect the drain hose to the drain outlet

at the back side of the washing machine.

Drain hose

Drain Outlet

Drain hose

If the washer is installed on an unsuitable floor, it could

make considerable noise, vibrate and cause a malfunction.

If washer is not level, adjust the front leg(A) up or down for

horizontal setting.

•Earthed electrical outlet(B) is required with 20cm of

bottom back of washer cabinet.

•Hot and cold water faucets (C) must be within 1M of the

upper back of the washer cabinet and provide water

pressure 0.3kgf/cm

2

-8kgf/cm

2

(2.94N/cm

2

-78.4cm

2

).

C

UP DOWN

A

B

NOTES

• The opening must not be obstructed by carpeting when the washing machine is

installed on a carpeted floor.

B

U

B

B

L

E

W

A

S

H

I

N

G

M

A

C

H

I

N

E

W

ASH

S

PA

RY

R

I

N

S

E

R

IN

S

E

SP

IN

F

U

Z

Z

Y

B

L

A

N

K

E

T

E

C

O

N

O

M

Y

W

O

O

L

W

A

T

E

R

L

E

V

E

L

R

E

S

.

C

O

U

R

S

E

P

R

O

C

E

S

S

S

T

A

R

T

H

O

L

D

P

O

W

E

R

S

O

A

K

RE

MA

I

N

M

I

N

.

H

O

T

C

O

L

D

W

A

S

H

T

E

M

P

.

W

A

S

H

T

E

M

P

.

W

A

T

E

R

L

E

V

E

L

C

O

N

T

R

O

L

O

N

L

Y

S

P

I

N

M

E

D

I

U

M

L

O

W

S

M

A

L

L

H

I

G

H

DWF-180MNP 01.3.26 9:41 PM ˘ ` 4

5

Recommended earthing method

WARNING

Laundry tub drain system Standpipe drain system

Pump Model

Non-Pump Model

1In case that it goes over

a door sill.

Don’t let the height of

the drain hose exceed

20cm from the bottom

of washer.

2In case of extending the

drain hose.

Don’t let the total length

exceed 3m.

3Be careful that the end

of the drain hose is not

immersed in water.

• Top of tub must be at least 86cm

(34inches) high and no higher than 130cm

from bottom of washer (A)

• Needs a 3cm minimum diameter

standpipe with minimum carry away

capacity of 30liters per minute.

• Top of tub must be at least 86cm

(34inches) high and no higher than 130cm

from bottom of washer (B)

20Cm

ELECTRICAL REQUIREMENTS

For your personal safety, this washer must be earthed.

This washer is equipped with a power supply cord (A) having a

earthing plug (B). To minimize possible shock hazard, the cord must

be plugged into a mating earthing-type wall receptacle (C).

If a mating wall receptacle is not available, it is the personal

responsibility and obligation of the customer to have the proper

earthed wall receptacle installed by a qualified electrician.

• Electrical earth is required on this washer

• If it does not fit the outlet, have a proper outlet

installed by a qualified electrician.

• Don’t earth to a gas pipe

• Don’t change the power supply cord plug.

• Check with a qualified electrician if you are not

sure the washer is properly earthed.

electrical shock hazard:failure to follow these instructions could result in

death or serious injury.

3m

A

B

C

B

A

DWF-180MNP 01.3.26 9:41 PM ˘ `5

6

Be careful not to confuse hot water inlet and cold water inlet.

In using only one water tap or in case of attached one water inlet valve, connect the

inlet hose to the cold water inlet valve.

For Screw-Shaped Tap

For Ordinary Tap

INLET HOSE CONNECTION

1Pull down the collar of

the inlet hose to separate

it from the water tap

2Loosen the four screws

properly in fitting into

water tap.

3Fit the water tap adapter

into the water tap tap

and tighten the four

screws evenly while

pushing up the adapter

so that the rubber

packing can stick to the

water tap tightly.

4Remove the tape, and

screw connector B into

connect A tightly.

5Connect the inlet hose to

the water tap adapter by

puling down the collar of

the hose end.

6Connect the inlet hose

adapter of the hose to

the water inlet of the

washer by turning it

clockwise to be fixed

tightly.

• Please check the rubber

packing inside the inlet hose

adapter of the hose.

1Connect the inlet hose to

the water tap by

screwing the connector

tightly.

2Connect the connector-

inlet supplied if

necessary.

3Insert the inlet hose

adapter into the water

inlet of a washer and turn

it to be fixed.

*Cheek the packing in the inlet

TAPE

adapter.

Connector B

Connector A

Connector

Connector

Rubber

Packing

Hose

Connector

Connector

Rubber

Packing

Hose

Connector

inlet

DWF-180MNP 01.3.26 9:41 PM ˘ `6