Daewoo DWDHQ1221 Instruction Manual
Customer Helpline Number : 01189252577
Spare Parts : 0844 557 0270 or www.4daewoo.co.uk / DAEWOO ELECTRONICS Web Site www.daewooelectronics.co.uk
A NOTE TO YOU
Thank you for buying a DAEWOO appliance.
DAEWOO washers are easy to use, save time, and help you manage your home better.
This manual contains valuable information about how to operate and maintain your washer properly and safely.
Please read it carefully.
INSTRUCTION MANUAL
DWDHQ1221
Washing Machine Instruction Manual
␊ Economic wash system
Using artificial intelligence, the washer uses minimum energy and water by
selecting optimal water level and washing time.
␊ Low noise system
The washer minimizes the washing and spinning noises by sensing the
amount of laundry.
␊ Child-Lock
The Child-Lock system has been used to prevent children from pressing any
button to change the program during operation.
CONTENTS Page
WASHER SAFETY...........................................................................................................................2
PARTS AND FEATURES.................................................................................................................4
INSTALLATION INSTRUCTIONS ....................................................................................................5
INLET HOSE CONNECTION ...........................................................................................................6
ELECTRICAL REQUIREMENTS .....................................................................................................7
OPERATING YOUR WASHER ........................................................................................................8
THE FUNCTIONS OF THE CONTROL PANEL.............................................................................10
WASHING PROCEDURE AND PROGRAM SELECTION.............................................................11
PRODUCT INFORMATION ...........................................................................................................25
MAINTENANCE ............................................................................................................................26
HOW TO CLEAN THE FILTER ......................................................................................................27
REMOVING STAINS ......................................................................................................................28
TROUBLE SHOOTING ..................................................................................................................29
SPECIFICATION & WIRING DIAGRAM ........................................................................................30
2
WASHER SAFETY
Save these instructions
Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your
washer, adhere to the following basic precautions.
• Flammable fluids (dry-cleaning solvents, kerosene, gasoline, etc.)
should not be used or stored in or near your washer.
Do not add flammable fluids to your wash water.These substances
give off vapors that can create a fire hazard or explosion.
• After starting a cycle, do not reach into the washer until all motions
stop.
• Do not tamper with the controls.
• The appliance is not intended for use by young children or infirm
persons without supervision.
• If the supply cord is damaged, it must be replaced by the
manufacturer, or its service agent or a similarly qualified person in
order to avoid a hazard.
• If the appliance is supplied from an extension cord or portable
electrical outlet device, it should be positioned so that it is not
subjected to splashing or ingress of moisture.
Please ...
• Have only a qualified person install, repair, or replace parts on
washer.
• Maintain washer properly, as per instructions
• Protect washer from the weather and keep it where the temperature
will not fall below freezing.
• Do not install the washer in a place of extremely high humidity.
It could cause an electric shock or a short circuit.
• Connect washer to the correct outlet, electrical supply, water supply,
and drain supply.
Read all instructions before using your washer
3
WASHER SAFETY
Understanding your responsibilities
• Do not use chlorine bleach and ammonia or acid(such as vinegar
or rust remover) in the same wash. Hazardous fumes can form.
• Unplug power supply cord before attempting to service your
washer.
• Do not wash fiberglass material.
Small particles can stick to fabrics washed in following loads and
cause skin irritation.
• Do not spray water on the control panel of the washer.
It could cause fire or an electric shock.
• In case of the dual valve model, if you connect only cold water
inlet valve, while water temperature is selected as hot or warm,
there can be water leakage from unconnected water inlet valve.
• This appliance must be grounded.
To avoid electrical shock, use a metal pipe for the ground
connection.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or metal
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazard involved.
• Children should not play with the appliance.
• Cleaning and user maintenance should not be carried out by
children without supervision.
• Children of less than 3 years should be kept away unless
continuously supervised.
• If you want to obtain user manual, please visit our website at
www
.daewooelectronics.co.uk or call our customer services on
01
18 925 2577.
4
PARTS AND FEATURES
The parts and features of your washer are illustrated on this page.
Become familiar with all parts and features before using your washer.
Accessories
NOTE
The drawings in the book may vary from your washer model.
They are designed to show the different features of all models covered by this book,
Your model may not include all features.
Inlet hose Manual Cap holder(3EA)
DETERGENT CASE
INLET HOSE
HOT
(OPTION)
COLD
DOOR
LOWER COVER
ADJUSTABLE LEG
HOSE DRAIN
CONTROL PANEL
POWER CORD
5
Removing transit bolts
1. Before operating the washer, remove the
transit bolts(x3) along with rubber around
them.
• If the bolts are not removed, it may cause
excess noise, vibration or malfunction.
2. Unscrew the 3 bolts with a 10mm hex
wrench or spanner or cross-tip screwdriver.
Do not discard the bolts.
• When the appliance is transported, the
transit bolts will need to be re-used.
3. Close the holes with the cap holders supplied.
Location of washer
• Check the location where the washer will be installed. Make sure you have everything
necessary for correct installation.
• Do not place or store your washer below 0°C (32°F) to avoid any damage from freezing.
• Do not place or store laundry products on top of washer at any times.
• Install the washer on the horizontal, solid, level floor.
If the washer is installed on an unsuitable floor, it could make
considerable noise, vibrate severely and cause a malfunction. If the
washer is not level, adjust leg up or down for horizontal installation.
• Ventilation openings must not be obstructed by carpeting when the
washer is installed on a carpeted floor.
•
Leave some space around the machine (right & left : 2cm, rear : 10cm).
• In case of built-in installation, the distance between top of the washer
and bottom of upper plate should be at least 3mm.
INSTALLATION INSTRUCTIONS
Drain Hose
Washer
Laundry
Tub
approx.
2cm
6
INLET HOSE CONNECTION
The washer should be connected to the water mains using new hose sets, old hose sets should
not be reused.
If in using only one water tap or in case of only one water inlet valve, connect the inlet hose to the
cold water inlet valve.
Note: Be careful not to confuse hot water inlet and cold water inlet if your model has a dual feed
For Ordinary Tap
1 Pull down the collar of
the inlet hose to separate
it from the water tap
adapter.
2 Loosen the four screws
properly in fitting into
water tap.
3 Fit the water tap adapter
into the water tap and
tighten the four screws
evenly while pushing up
the adapter so that the
rubber packing can
attach to the water tap
tightly.
1 Connect the inlet hose to
the water tap by screwing
the connector tightly.
2 Connect the connector-
inlet supplied if
necessary.
3 Insert the inlet hose
adapter into the water
inlet of a washing
machine and turn it to be
fixed. .
4 Remove the tape, and
screw connector B into
connector A tightly.
5 Connect the inlet hose to
the water tap adapter by
pulling down the collar of
the hose end.
6 Connect the inlet hose
adapter of the hose to the
water inlet of the washing
machine by turning it
clockwise to be fixed
tightly.
For Screw-Shaped Tap
• Please check the rubber
packing inside the inlet hose
adapter of the hose.
* Check the packing in the inlet
Connector B
Connector A
Connector
Hose Connector
Rubber
Packing
Connector
inlet
Connector
Hose Connector
Rubber
Packing
TAPE
7
ELECTRICAL REQUIREMENTS
Drain system
• Never forget to install the drain hose before operating your washer.
• Open the packing box, and the drain hose is inside the drum.
• Connect the drain hose to the drain outlet at the back side of the washer.
•
Top of laundry tub must be at least 60cm high and no higher than 100cm from bottom of washer.
• If the machine is not installed correctly, it could 'back fill' with dirty water from the waste pipe so
please follow the instructions carefully.
• When installing the drain hose to tub(sink), secure it tightly with a cable tie or other suitable
device.
• Proper securing of the drain hose will protect the floor from damage due to any water leakage.
• When the drain hose is too long, do not force it back into the washer.
This will cause abnormal noise.
Level adjustment
1 If the washer is installed on an
unsuitable floor, it could make
considerable noise, vibrate and
cause a malfunction.
Laundry tub
max. 100 cm
min. 60 cm
ca. 105 cm
Tie
strap
max. 100 cm
min. 60cm
max. 100 cm
min. 60cm
WARNING
• Electrical earth is required on this washer.
• If it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Don't earth to a gas pipe.
• Don't change the power supply cord or plug.
• Check with a qualified electrician if you are not
sure the washer is properly earthed.
Recommended earthing method
For your personal safety, this washer must be earthed.
This washer is equipped with a power supply cord ‘A’having a earthing plug ‘B’.
To minimize possible shock hazard, the cord must be plugged into a mating
earthing-type wall receptacle ‘C’. If a mating plug socket is not available, it is the
personal responsibility and obligation of the customer to have the proper earthed
plug socket installed by a qualified electrician.
A
B
C
Electrical shock hazard : Failure to follow these instructions could result in
death or serious injury.
8
OPERATING YOUR WASHER
2 Adjust the level of washer.
• Adjust the level of washer by turning the
adjustable legs.
• Please check if there is any gap between
the four adjustable legs and the floor.
• After the adjustment is finished, turn the
fixing nuts up tightly so that the washer
maintains the adjustment.
3 Make it sure that the washer does not sway when you press
down the four corners of the washer's top plate.
adjustable leg
Fixing Nut
To obtain the best washing results, you must operate your washer properly, as per instructions.
This section gives you this important information.
• Close zippers, snaps, and hooks to avoid
snagging other items.
Remove pins, buckles, and other hard
objects to avoid damaging the washer
interior.
• Empty pockets and pull them inside out.
• Turn down cuffs and turn synthetic knits
inside out to avoid pilling.
• Tie strings and sashes to avoid tangling.
• Treat spots and stains.
(See “Removing stains” on page 27)
Preparing clothes for washing
9
• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.
• Separate dark colours from light colours, colourfast items from non-colourfast item.
Soil (Heavy, Normal, Light) Separate clothes according to amount of soiling.
Colour (White, Lights, Darks) Separate white clothes from coloured clothes.
Lint (Lint producers, Collectors) Wash lint producers and lint collectors separately
Sorting
• Drop items into washer loosely. Items should move
easily through wash water for best cleaning and
wrinkle-free results.
• Load washer properly and select correct load size
setting.
Overloading and selecting a setting too small for the
wash load can :
- Cause poor cleaning
- Increase wrinkling
- Create excessive lint
- Wear out items faster (because of pilling)
• Mix large and small items in each load. Load evenly
to maintain washer balance.
An unbalanced load can make the washer vibrate
during spin or cause spin cycle not to be completed.
• Reduce wash time when using a small load size
setting. Loads with only a few small items need less
wash time.
• Use a large load size setting to reduce wrinkling
with permanent press clothes and some synthetic
knits. These items should have more room to move
in the water than heavy items. (towels, jeans)
1 Detergent case 2 Adding fabric softener
• If desired, add measured liquid fabric
softener to the softener inlet.
• Pour liquid fabric softener into the
dispenser using the amount recommended
on the package.
• Do not exceed the maximum fill line.
Overfilling can cause early dispensing of the
fabric softener which could stain clothes.
• Do not open the detergent case when
water is supplied.
• Avoid pouring fabric softener directly on
the clothes.
• Please use the proper amount of detergent in conformity with the instructions of the detergent manufacturer.
• A use of a large amount of detergent more than the recommended amount can cause many soapsuds and
the overload to the motor. In addition to, this will deteriorate the washing and rinse performance.
Main wash Pre wash
Fabric softener
Loading
Adding detergent
10
THE FUNCTIONS OF THE CONTROL PANEL
Press this switch to turn the power on or off.
Operation and temporary stop is repeated as it is pressed.
When you want to change program in operation;
Press the ‘Start/Pause’ button ᵎ Select the program that you want to change ᵎ
Press the ‘Start/Pause’ button again.
You can select the course you want, and each light is turned on when that cycle
is selected.
For the more detailed information, please refer to the page 12~24.
It can be used to adjust temperature of water according to types of the load to be
washed. As the button is pressed, temperature of water is selected by
Cold ᵎ 20°C ᵎ 40°C ᵎ 60°C ᵎ 95°C
By pressing the spin button, the spin speed can be chosen.
Rinse Hold • Is selected by pressing the spin button repeatedly. This function leaves clothes in
the machine; suspended in the water after a rinse without entering into spin.
• To proceed through to a drain or spin, after the Rinse Hold function is completed,
use spin button.
Spin Only • If you want only spin, you can operate spin only.(See page 24.)
Pre-Wash • The washer operates one additional wash and spin before the main wash.
• If the laundry is heavily soiled, Pre-Wash course is effective.
• Pre-Wash is available in Cotton, Baby Care and Synthetic programs.
Rinse+ • Is used to add a rinse, which may assist in removing traces of detergent residue.
• By selecting Rinse+ function, the rinse time and the rinse water are increased.
Water+ • If you want to use more water in the rinsing, press this button.
Use this function when you want to reduce the laundry time or wash the mild dirty.
It reduces the laundry time and saves (lower) energy consumption.
It can be used to pre-engage time for wash.
Reservation can be made from 1 hours to 12 hours.
Use this function when you want to protect any accident occurring from handling of washer by a
child. During an operation of washer, press ‘Spin’ and ‘Option’ buttons simultaneously.
In Child Lock mode, no button functions except for Power button.
In Child Lock mode, press ‘Spin’ and ‘Option’ buttons simultaneously like setting Child Lock and
Child Lock is cancelled.
To change to the desired program, while in Child Lock mode;
1. Press both the ‘Spin’ and ‘Option’ buttons together once again.
2. Press the Start/Pause button.
3. Select the desired program and
press the Start/Pause button again.
• The Child Lock will be cancelled when
power is off.
Use this function when you want the machine not to alarm when finished.
During an operation of washer, press 'Temp.' and 'Spin' buttons simultaneously.
You should set this function whenever you want to silence the buzzer.
Change the
desired
program
11
1. COTTON IS AUTOMATICALLY SELECTED UPON POWER ON
• Press the Power button to start.
• Press the Start/Pause button.
• Initial condition.
- Program : Cotton
- Wash : main wash
- Rinse : 3 times
- Spin : 800 rpm
- Water temperature : 40˚C
WASHING PROCEDURE AND PROGRAM SELECTION
2. MANUAL SELECTING
• Press the Power button to start.
• Select the conditions which you want to use by turning the program dial and pressing each button.
• Press the Start/Pause button.
* Each pressing of the button advances time delay by one hour.
• If you want to check the selected program, press the 'Start/Pause' button again.
• To cancel the time delay, press the Power button.
3. TIME DELAY
• Time delay can be set from 1 hour to 12 hours.
eg.) To make reservation to complete washing in 8 hours.
- Procedure to press the button.
select the
program
(as above)
adjust to "8"
Loading...