Daewoo DWDG1281 User Manual [nl]

Washing Machine Instruction Manual
2011.05.19
세)생산기술팀
사양 확인 및 배포
DWD-G1281B
INSTRUCTION MANUAL
" Economic wash system
Using artificial intelligence, the washer uses minimum energy and water by selecting optimal water level and washing time.
" Low noise system
The washer minimizes the washing and spinning noises by sensing the amount of laundry.
" Child-Lock
The Child-Lock system has been used to prevent children from pressing any buttons to change the programme during operation.
" Air bubble washing
This is an advanced technology that generates millions of air bubbles inside the drum on washing sequence, and the bubbles dissolve the detergent particles efficiently and clean clothes gently and neatly even in cold water without compromising on washing performance.
CONTENTS Page
PARTS AND FEATURES.................................................................................................................2
WASHER SAFETY...........................................................................................................................3
INSTALLATION INSTRUCTIONS....................................................................................................4
INLET HOSE CONNECTION...........................................................................................................5
ELECTRICAL REQUIREMENTS .....................................................................................................6
OPERATING YOUR WASHER........................................................................................................7
THE FUNCTIONS OF THE CONTROL PANEL...............................................................................9
WASHING PROCEDURE AND PROGRAM SELECTION.............................................................11
MAINTENANCE .............................................................................................................................23
HOW TO CLEAN THE FILTER......................................................................................................24
REMOVING STAINS......................................................................................................................25
TROUBLE SHOOTING ..................................................................................................................26
SPECIFICATION & WIRING DIAGRAM ........................................................................................27
A NOTE T O YOU
Thank you for buying a DAEWOO appliance. DAEWOO washers are easy to use, save time, and help you manage your home better. This manual contains valuable information about how to operate and maintain your washer properly and safely. Please read it carefully.
Customer Service Helpline : 0844 887 2525
PARTS AND FEATURES
The parts and features of your washer are illustrated on the page. Become familiar with all parts and features before using your washer.
NOTE
The drawings in the book may vary from your washer model. They are designed to show the different features of all models coverd by this book, Your model may not include all features.
COLD
INLET HOSE
DETERGENT CASE
DOOR
Accessories
Inlet hose Manual Cap holder(3EA)
PUMP COVER
POWER CORD
CONTROL PANEL
HOSE DRAIN
ADJUSTABLE LEG
2
WASHING MACHINE SAFETY
Save these instructions
Your safety is important to us. To reduce the risk of fire, electrical shock, or injury when using your machine adhere to the following basic precautions.
Read all instructions before using your machine
• Flammable fluids (dry-cleaning solvents, etc) should not be used or stored in or near your machine. Do not add flammable fluids to your wash. These substances give off vapours that can create a fire hazard or explosion.
• Do not attempt to open the machine door after a cycle has started.
• Do not tamper with the controls.
• The appliance is not intended for use by young children or without supervision.
• If the supply cord is damaged, it must be replaced by the manufacturer, or its service agent or a similarly qualified person in order to avoid a hazard.
• If the appliance is connected to the power supply via an extension lead, it should not be positioned where it could be splashed by, or susceptible to, water.
Please ...
• Have only a qualified person install, repair, or replace parts on washer.
• Ensure your washing machine is regularly maintained/serviced.
• Position your washing machine where it will be protected from the weather and keep it where the temperature will not fall below freezing.
• Do not install your machine at a place of extremely high humidity. It could cause an electric shock or a short circuit.
• Your washing machine must be connected to the correct outlet, electrical supply, water supply, and drain supply.
Understanding your responsibilities
• Do not use chlorine bleach and ammonia or acid(such as vinegar or rust remover) in the same wash. Hazardous fumes can form.
• Unplug power supply cord before attempting to service your machine.
• Do not wash fibreglass material. Small particles can stick to fabrics washed in subsequent loads and cause skin irritation.
• Do not spray water on the control panel of the washer. It could cause fire or an electric shock.
• In case of the dual valve model, with only the cold water inlet valve connected and the water temperature selected as hot or warm, there may be water leakage from unconnected water inlet valve.
• This appliance must be earthed.
3
INSTALLATION INSTRUCTIONS
Removing transit bolts
1. Before operating the washer, remove the transit bolts(3ea) along with the rubber.
• If the bolts are not removed, it may cause
heavy vibration, noise and malfunction.
3. Close the holes with the cap holders supplied.
2. Unscrew the 3 bolts with a 10mm hex wrench or spanner or cross-tip screwdriver. Keep the 3 bolts for a later time.
• When the appliance is transported, transit
bolts can be re-used.
Location of washer
• Check location where the machine will be installed. Make sure you have everything necessary for correct installation.
• Do not place or store your washing machine below 0°C (32°F) to avoid any damage from freezing.
• Never place/store laundry products on top of the machine.
• Install the washer on a horizontal solid floor.
If the washer is installed on an uneven floor, it could make considerable noise, vibrate severely and cause a malfunction. If the machine is not level, adjust the legs up or down for horizontal installation.
• Ventilation openings must not be obstructed by carpeting when the machine is installed on a carpeted floor.
• Leave some space (right & left : 2cm, rear : 10cm).
• In case of built-in installation, the distance between top of the
washer and bottom of upper shelf should be at least 3mm.
4
Washer
approx.
Drain Hose
Laundry
Tub
2cm
INLET HOSE CONNECTION
The machine should be connected to the water mains using the the new hose sets supplied. NEVER reuse old hoses. If using only one water tap or if there is only one water inlet valve, connect the inlet hose to the cold water inlet valve. Caution: Be careful not to confuse hot water inlet and cold water inlet.
For Ordinary Tap
1 Pull down the collar of
the inlet hose to separate it from the water tap adapter.
4 Remove the tape, and
screw connector B into connect A tightly.
Water tap adapter 'A' Water tap adapter 'B'
2 Loosen the four screws
properly in fitting into water tap.
5 Connect the inlet hose to
the water tap adapter by pulling down the collar of the hose end.
3 Fit the water tap adapter
into the water tap and tighten the four screws evenly while pushing up the adapter so that the rubber packing can attach to the water tap tightly.
TAPE
6 Connect the inlet hose
adapter of the hose to the water inlet of the washing machine by turning it clockwise to be fixed tightly.
• Please check the rubber packing inside the inlet hose adapter of the hose.
For Screw-Shaped Tap
1 Connect the inlet hose to
the water tap by screwing the connector tightly.
Rubber
Connector
Hose Connector
Packing
2 Connect the connector-
inlet supplied if necessary.
Connector
inlet
Connector
Hose Connector
Rubber Packing
5
3 Connect the inlet hose
adapter to the water inlet of the machine and turn it until tight.
*Check the rubber packing is
present inside the inlet.
ELECTRICAL REQUIREMENTS
C
A
B
WARNING
• An electrical earth is required on this machine
• If it does not fit the outlet, have a proper outlet installed by a qualified electrician.
Electrical shock hazard : Failure to follow these instructions could result in
death or serious injury.
• Don’t earth to a gas pipe.
• Don’t change the power supply cord plug.
• Check with a qualified electrician if you are not sure the machine is properly earthed.
Recommended earthing method
For your personal safety, this machine must be earthed. It is fitted with a supply lead (A) attached to an earthed plug (B). To prevent electric shock occurring, this machine must be plugged into the relevant earthed power socket (C). It is the personal responsibility and obligation of the customer to ensure that this is in place before the washing machine is installed.
Drain system
• Never forget to install the drain hose before operating your machine.
• Open the packing box, and there is a drain hose inside the drum.
• Connect the drain hose to the drain outlet at the back side of the machine. The outlet of the drain hose when connected to the sink outlet or simply placed in the sink basin
• must be at least 60cm high but no higher than 100cm from floor level.
Laundry tub
Hose
Retainer
max. 100 cm
min. 60 cm
ca. 105 cm
Tie
strap
max. 100 cm min. 60cm
max. 100 cm min. 60cm
• When installing the drain hose to tub(sink), secure it tightly with string or a plastic strap.
• Proper securing of the drain hose will protect the floor from flooding.
• When the drain hose is too long, do not force it back into the machine as this will cause excessive noise.
Level adjustment
1 If the washer is installed on an
unsuitable floor, it could make considerable noise, vibrate and cause a malfunction.
6
2 Adjust the level of the washing machine using the adjustable legs.
• Please check there is no gap between any of the four adjustable legs and the floor.
• Turn the adjustable legs and adjust the level of the machine to make sure that it is stable.
• Adjust the fixing nuts tightly so that the lecs maintain the adjustment.
3 Make it sure that the washing machine does not move when you
press down on the four corners of the washer's top plate.
NOTE
There should be no instability of the machine when
all the adjustable legs have been correctly balanced.
adjustable leg
OPERATING YOUR W ASHING MACHINE
Fixing Nut
To obtain the best washing results, you must operate your machine properly. This section gives you this important information.
Preparing clothes for washing
• Close zippers, snaps, and hooks to avoid
snagging other items. Remove pin, buckles, and other hard objects to avoid scratching the machine interior.
• Empty pockets and pull them inside out.
• Turn down cuffs and turn synthetic garments inside out to avoid damaging the fibres.
• Tie strings and sashes to avoid tangling.
• Treat spots and stains. (See “Removing stains” on page 21)
7
Sorting
• Separate heavily soiled items from lightly soiled ones, even if they would normally be washed together.
• Separate dark colours from light colours, colourfast items from non-colourfast items.
Soil (Heavy, Normal, Light) Separate clothes according to amount of soil. Colour (White, Lights, Darks) Separate white clothes from coloured clothes. Lint (Lint producers, Collectors) Wash lint producers and lint collectors separately.
Loading
• For best cleaning and wrinkle-free results, put clothes into the machine loosely so that they move easily in the water.
• Load machine properly and select correct load size setting. Overloading and selecting a setting too small for the wash load can :
- Cause poor cleaning
- Increase wrinkling
- Create excessive lint
- Wear out items faster (because of damage to fibres)
• Mix large and small items in each load. Load evenly to maintain washer balance. An unbalanced load can make the washer vibrate during spin.
• Reduce wash time when using a small load size setting. Loads with only a few small items needs less wash time.
• Use a large load size setting to reduce wrinkling with permanent press clothes and some synthetic garments. These items should have more room to move in the water than heavy items. (towels, jeans)
Adding detergent
1 Detergent compartment 2 Adding fabric softener
• If desired, pour liquid fabric softener into the dispenser using the amount recommended by the manufacturers.
• Do not exceed the maximum fill line. Overfilling can cause early dispensing of the fabric softener which could stain clothes.
• Do not open the detergent case when water is supplied.
• Avoid pouring fabric softener directly on the clothes.
Main wash
Pre wash
Fabric softener
3 Please use only the powder detergent for the front loader washing machine.
• Please use the proper amount of detergent in conformity with the instruction of the detergent manufacturer.
• A use of a large amount of detergent more than the recommended amount can cause many soapsuds and overload to the motor. In addition to, this will deteriorate the washing and rinse performance.
8
THE FUNCTIONS OF THE CONTROL PANEL
When users select a course, the selected course number is shown before estimated time is displayed.
Programmes selector
For switching the washing machine on and off and for selecting the programmes. You can select the course you want by rotating programme selector. For the more detailed information, please refer to the page 11~22. Can be rotated in both direction. You can turn off the power by rotating programme selector to the direction at 12 o'clock. Even if the programme selector rotates while the programme is running, the programme is not changed(except for off ).
Operation and temporary stop is repeated as it is pressed. When you want to change programme in operating; press the ‘Start/Hold’ button → Turn the programme selector to OFF (over 1 sec) select the programme that you want to change press the ‘Start/Hold’ button again.
Rinse+
• Is used to add a rinse, which may assist in removing traces of detergent residue.
• By selecting Rinse+ function, the rinse time and the rinse water are increased.
Rinse+ option is selectable with all programmes except Wool, Spin and Drain
programmes.
9
Rinse Hold
• This function leaves clothes in the machine suspended in the water after a rinse without entering into spin.
• To proceed through to a drain or spin, after the Rinse Hold function is completed, use programme selector(Drain or Spin programme).
• Rinse Hold option is selectable with all programmes except Wool, Spin and Drain programmes.
• The LED shows “rH” while Rinse hold state.
Time Delay
• It can be used to pre-engage time for wash.
• Reservation can be made from 1 hours to 12 hours.
• Time Delay function is selectable with Wool, Spin and Drain programmes.
Child Lock Mode
• Use this function when you want to protect any accident occurring from handling of washer by a child.
• During an operation of washer, press ‘Rinse+’ and ‘Rinse Hold’ buttons simultaneously.
• In Child Lock mode, no button functions except for off .
• In Child Lock mode, press ‘Rinse+’ and ‘Rinse Hold’ buttons simultaneously like setting Child Lock and Child Lock is cancelled.
• To change to the desired programme, while in Child Lock mode;
1. Press the Start/Hold button.
2. Press both the ‘Rinse+’ and ‘Rinse Hold’ buttons
together once again.
• The Child Lock will be cancelled when power is off or Press both the ‘Rinse+’ and ‘Rinse Hold’ buttons together .
10
+ 21 hidden pages