Daewoo DW-5014 User Manual
PARTS IDENTIFICATION
ACCESSORY
R
O
T
A
T
I
O
N
L
I
M
I
T
R
O
T
A
T
I
O
N
L
I
M
I
T
•TUB
•OVERFLOW FILTER
•WASHER LID
•DRAIN STRAINER
•PULSATOR
•BASE
•SPINDRYER LID
•INNER LID
•SPINDRYER DRUM
•GROUND WIRE
(OPTION)
•POWER CORD
Control panel
SPIN TIMER
0
MIN
1
2
3
4
5
WASH TIMER
R
O
T
A
T
I
O
N
L
I
M
I
T
O
F
F
W
A
S
H
•
R
I
N
S
E
D
R
A
I
N
VALVE SELECTOR
0
MIN
3
6
9
12
15
R
O
T
A
T
I
O
N
L
I
M
I
T
Water Inlet
Connect the hose from the water faucet to feed water to the tub.
Wash Timer
Use to select the desired time for washing or rinsing.
Drain Selector
Select “WASH · RINSE” for washing and rinsing, and “DRAIN” to drain the tub.
“OFF” to turn off the drain pump. (Model with pump)
Spin Timer
Use to select the desired time for spinning.
LEG (4EA) SAFETY COVER
DRAIN HOSE
PUMP
①
①
②
②
③
④
③
1
④
INSTALLATION
Caution: If the power cord is damaged, it should be replaced by a repair shop appointed by the
manufacturer, as special purpose tools are required.
■ Electrical Connection
•
This unit is designed to operate from an adequate supply mentioned on the rating label attached to the rear of the unit.
■ Location & Environment
• Do not place the washer in steamy rooms or where the washer is directly exposed to rain.
Moisture may destroy the electrical insulation and cause an electric shock hazar
WASHER SAFETY
Save these instructions
Your safety is important to us.
To reduce the risk of fire, electrical shock, or injury when using your washer adhere to the following
basic precautions.
Read all instructions before using your washer
- This washing machine is not intended for use by young children or infirm person without supervision.
- Young children should be supervised to ensure that they do not play with this washing machine.
- If this appliance is supplied from a cord extension set or an electrical portable outlet device,
these should be positioned so they are not subject to splashing or ingress of moisture.
d.
•Place washer on a sturdy flat surface. If the washer is placed on an uneven or weak surface,
noise or vibration may occur. (Allowable inclination is max. 2degrees)
•Avoid direct sunlight or heating devices, as plastic and electrical components are affected by direct
heat. Never place the washer near heaters, boilers etc...
•Do not place or store the washer below 0˚C(32˚F) to avoid any damage from freezing.
How to Fix Legs
• When you install this unit, be sure to assemble legs(4EA) to BASE.
• Place this unit on its rear side on a carton to prevent damage to body.
• Insert the legs(4EA) into the BASE in the rectangle hole
by first inserting its hook.
• Push and screw on legs. (4EA)
HOOK
2
• Connection of Hoses
• Attach the water intake hose to the water inlet located in
the control panel. Fit the other end of the hose to
either a hot or cold water tap as required.
• Attach the drain hose to the drain outlet at the rear of the base.
• Hang the drain hose on the edge of a sink.
Caution:This unit is made of poly propylene, use water
below 60 °C
Caution:The opening must not be obstructed by carpeting when the washing machine is installed on a
carpeted floor.
Drain Outlet
Drain hose
A
HOW TO WASH
Preparation
How to Wash
(PUMP)
• Sort the clothes into groups-whites, colourfast, non-colourfast, delicates, lint free, lint producer, etc., and
wash according to the
LAUNDRY GUIDE.
• Clothes with worn patches or tears should first be mended. Empty out all pockets and close all side
fasteners. Treat bad stains prior to washing.
• Ensure the drain hose is in its correct position. (See INSTALLATION)
• Insert power cord plug into the power point and switch on.
1
2
3
4
5
3
WASH TIMER
R
O
T
A
T
I
O
N
L
I
M
I
T
VALV
ESELECTOR
○
Set the wash timer knob to position “0” and set the drain selector to the “WASH · RINSE” or “OFF” position.
Open the water faucet and feed water to the water level indicated inside the wash tub.
○
○
Put the detergent and laundry into the wash tub.
Set the wash time with the wash timer.
○
When washing is finished, set the drain selector to the “DRAIN” position and drain the wash tub.
○
Loading...