Daewoo DW-424 User Manual

INSTALLATION

Electrical Connection

• In case of 3-core cord: The power cord plug must be connected to an earthed 3-pin power point
within reach of the power cord.

• In case of 2 conductor power cord: Connect the grounding wire to a water faucet etc. Make sure
that the power cord is unplugged during ground work.

Connection of Houses

• Attach the drain hose to the drain outlet at the left side of
the under base and secure with the clamp provided.
Hang the “U” Shaped outlet of the drain hose on the
edge of a sink.

• Attach the water intake hose to the water inlet located at
the left-hand side of the control panel. Press fit the other
end of the hose to either a hot or cold water tap as
required (Fig. 1).

WATER INLET PORT

1

PARTS IDENTIFICATION

Water Inlet Port

Pulsator (with Lint-filter)

Drain Hose Assembly (PUMP)

Safety Cover

Wash Tub

Wash-Tub Lid

Wash Action Selector

Drain Strainer

Overflow Strainer

Spin Timer Switch (5 min. timer)

Power Cord
Spin Tub

Power Cord Rack
Panel Front

Drain Hose Assembly
(NON-PUMP)

Inner Lid os Spin-dry Tub
Prevent your hands, etc.,
from touching the spin-dry
basket in rotation

Spin-tub Lid
When this lid is opened, the spin dryer
immediatelystops operating

Drain Selector (Pump Control Switch)

Rub-Wash Section

Wash Timer Switch
(15 min. timer)

Accessories

Lint Filter

Figure 1.

2

OPERATING INSTRUCTIONS

Preparing the Wash

●

Sort the clothes into groups-whites, colourfast, non-colourfast, delicates, lint free, lint producers,
etc., and wash according to the Laundry Guide below.

●

Clothes with worn patches or tears should first be mended. Empty out all
pockets and close all slide fasteners. Treat bad stains prior to washing.

Prior to Washing

●

Remove the plastic spin mat from the spin bowl.

●

Check that the wash timer knob is set to position “0” and that the drain selector is set to “wash ·
rinse”.

●

Also check that the lint filter is correctly positioned.

●

Ensure the drain hose is in its correct position (see lnstallation).

●

Insert the power cord plug into the power point and switch on.

To Wash

• Place the wash load and detergent in the wash tub. Refer to “Preparing the Wash” and “Points to
Remember”

• Set the drain selector to “wash · rinse”

• Turn the water tap on fill the tub of your washing machine to the level recommended in the
Laundry Guide.

• Set the selector switch to the position recommended in the Laundry Guide.

DRAIN HOSE SETTING

(1) Connect the drain hose to the drain outlet at the rear side of

your washer, and then fasten it tightly with the hose clamp.

(2) The other end of the drain hose setting toward the bath or

sinkhole.

(3) Install the drain hose about 85cm from the ground.

(In case drain pump model)

Hose Clamp

Drain Outlet

Drain hose

A

OPERATING INSTRUCTIONS

• Set the wash timer to the wash period recommended in the Laundry Guide.
Your machine will now wash for the period selected.

• When the wash period expires, set the drain selector to the drain position
to discharge the water.

Note: Before rinsing, the wash load may be transferred to the spin bowl to spin dry for 1

minute (approx.) to remove excess suds (see Spin Drying). On completion, transfer the
wash load to the wash tub for rinsing.

To Rinse in the Wash Tub

• Set the drain selector to the “wash · rinse” position.

• Turn the water tap on.

• When the rinse water becomes clear, turn off the water tap.

• Set the drain selector the drain position to discharge the water.

Note: The pump is turned on when the water reaches approx. 7cm above level H. It is then

turned off when the water returns to approx.
2cm below level H. It is operated automatically so that the water level maintains between
approx. 2cm below level H and approx. 7cm above level H.

Spin Drying

• To open the inner safety lid of the spin bowl, lift up the outer lid, then pull the catch forward

and lift upward.

• Transfer either the full wash load or portion to the spin bowl commencing with small articles.

Ensure that the clothes are evenly distributed.

• Place the removable spin mat over the load to be dried and push lightly downward. (To con-

tain delicated articles within the spin bowl.)

• Close the inner safety lid, then the outer lid.

• Set the spin timer to the time recommended in the Laundry Guide. The spin bowl will spin for

the time selected, then stop (at position “0”).

Caution: Ensure that the spin bowl completely stops before reaching in to remove

the wash load.

• To remove or reposition clothes during the spin dry cycle, open the outer and inner lids. In

this case, the spin bowl will automatically stop as a brake is applied when the outer lid is
opened. To restart, close both lids. If required, reset the spin timer.

Note: The pump motor will operate when the spin dry timer is set,

irrespective of whether the outer lid is closed or opened.

OPERATING INSTRUCTIONS

Simultaneous Washing and Spin Drying

• Three motors ate fitted to cover washing, spin drying and drainage.

This arrangement enables spin drying of a previous wash load and washing of a new wash
load to be simultaneously effected.

• To do this, set the controls for both “wash” and “spin” modes

(see “to wash” and “spin drying”).

Laundry Guide

Size of Degree Wash Water
Type of Wash Water of Selection Temperature Wash Spin
Fabric Load Level Soiling Switch Wash Cycle Period Period

Fast Full High Heavy Heavy
Coloured Hot 60˚C

5-10 mins. 3-5 mins.

Cotton and Half & Medium Normal Normal Max.
Linens Less Light

Nylon Full High Normal Normal

Warm 40˚C

4-5 mins.

2 mins.

and P.P Half & Medium Light Soft 2-3 mins.

Less or Low
Delicates Half &

High

Normal

Soft Warm 40˚C 2-3 mins. 1-2 min..

Less to Light

3