DAEWOO DTQ-21U6SSV, DTQ-21U6SSFV, DTQ-20S1SSFV Service Manual

Caution

: In this Manual, some parts can be changed for improving. their
performance without notice in the parts list. So, if you need the
latest parts information, please refer to PPL(Parts Price List)in
Service Information Center.

Service Manual

Color Television

S/M No : TCN402FEF0

MAR. 2006

CHSSIS MODEL

CN-402FN DTQ-20S1SSFV

DTQ-2130SSFV
DTQ-21D7SSPV
DTQ-21U6SSFV
DTQ-21U6SSV

-1-

SAFETY PRECAUTIONS 2
SPECIFICATIONS 5
CIRCUIT BLOCK DIAGRAM 6
ALIGNMENT INSTRUCTIONS 7

YOUR REMOTE CONTROL 7
SERVICE MODE ADJUSTMENT 8
ASSEMBLY ADJUSTMENT 10

IC DESCRIPTION 14

UOC III SERIES 14
TDA8358J VERTICAL AMPLIFIER 26
TDA6107AJF 28
24WC16-16 KB EEPROM 29
LA42072N-E AUDIO AMPLIFIER 30

STR-W6735/56 31
WAVEFORMS 33
TROUBLE SHOOTING GUIDE 35

NO POWER 35

NO PICTURE 36

NO SOUND 37

CH DON’T MEMORY or SKIP 38

NO COLOR 39

NO VERTICAL DEFLECTION 39

REMOTE CONTROL DOESNOT OPERATE 40
ELECTRICAL PARTS LIST 41
DIFFERENT PARTS LIST 53
PRINTED CIRCUIT BOARD 56
SCHEMATIC DIAGRAM 59
EXPLODE VIEW 61

TABLE OF CONTENTS

APPENDIX(Appendix is provide only by internet[http://svc.dwe.co.kr])

-2-

SAFETY PRECAUTIONS

CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY.
NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFAC­TURER'S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY VOID
THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANT RESULT­ING PROPERTY DAMAGE OR USER INJURY.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE THOR­OUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY CHECKS AND
SERVICING GUIDELINES. TO DO OTHERWISE, INCREASES THE RISK OF
POTENTIAL HAZARDS AND INJURY TO THE USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION
FROM A.C. LINE SHOCK.

SAFETY CHECKS

AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED, A CHECK
SHOULD BE MADE OF THE FOLLOWING:

SUBJECT:FIRE & SHOCK HAZARD

1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY AS
TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS. THIS IS
ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARE TRANS­PORTED TO AND FROM THE REPAIR SHOP.

2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES SUCH AS
INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN RELIEFS, POWER
SUPPLY CORDS, AND OTHER HARDWARE HAVE BEEN REINSTALLED PER
ORIGINAL DESIGN. BE SURE, THAT THE SAFETY PURPOSE OF THE
POLARIZED LINE PLUG HAS NOT BEEN DEFEATED.

3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD SOL­DER JOINTS, SOLDER SPLASHES OF SHARP SOLDER POINTS. BE CER­TAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.

4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATION TO
PARTS AND COMPONENTS, FOR FRAYED LEADS, DAMAGED INSULATION
(INCLUDING A.C. CORD), AND REPLACE IF NECESSARY. FOLLOW ORIGI­NAL LAYOUT, LEAD LENGTH AND DRESS.

5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING TUBE OR A
RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND PRO­TRUDING METAL SURFACES MUST BE AVOIDED.

6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOF RESISTOR,
CAPACITORS, ETC. MUST BE REPLACED WITH EXACT FACTORY TYPES.
DO NOT USE REPLACEMENT COMPONENTS OTHER THAN THOSE SPECI­FIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS.

7. AFTER RE-ASSEMBLY OF THE STE ALWAYS PERFORM AN A.C. LEAKAGE
TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET. (THE CHAN­NEL SELECTOR KNOB, ANTENNA TERMINALS, HANDLE AND SCREWS) TO
BE SURE THE SET IS SAFE TO OPERATE WITHOUT DANGER OF ELECTRI­CAL SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER DURING THIS
TEST USE AN A.C. VOLTMETER, HAVING 5000 OHMS PER VOLT OR MORE
SENSITIVITY, IN THE FOLLOWING MANNER : CONNECT A 1500 OHM 10
WATT RESISTOR, PARALLELED BY A .15 MFD. 150V A.C. TYPE CAPACI­TOR BETWEEN A KNOWN GOOD EARTH GROUND (WATER POPE, CON­DUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.
MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500 OHM
RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUG AND
REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED METALLIC
PART. VOLTAGE MEASURED MUST NOT EXCEED .75 VOLTS R.M.S THIS
CORRESPONDS TO 0.5 MILLIAMP A.C. NAY VALUE EXCEEDING THIS LIMIT
CONSTITUTES A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED
IMMEDIATELY.

SUBJECT : X-RADIATION

1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSON­NEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL
SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE.
HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHEN THE HIGH VOLT­AGE IS AT THE FACTORY SPECIFIED LEVEL. THE PROPER VALUE IS GIVEN
IN THE APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLT-AGES MAY
CAUSE A FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE SUPPLY
AND UNDER CERTAIN CIRCUMSTANCES, AMY PRODUCE RADIA-TION IN
EXCESS OF DESIRABLE LEVELS.

2. ONLY FACTORY SPECIFIED C.R.T ANODE CONNECTORS MUST BE
USED.DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD IN COLOR
SETS. ALWAYS RE-INSTALL THEM.

3. IT IS ESSENTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN ACCU­RATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRATION OF THE
METER SHOULD BE CHECKED PERIODICALLY AGAINST A REFERENCE
STANDARD. SUCH AS THE ONE AVAILABLE AT YOUR DISTRIBUTOR.

4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY THERE
IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY TIME A COLOR
CHASSIS IS SERVICED, THE BRIGHTNESS SHOULD BE RUN UP AND DOWN
WHILE MONITORING THE HIGH VOLTAGE WITH A METER TO BE CERTAIN
THAT THE HIGH VOLTAGE DOES NOT EXCEED THE SPECIFIED VALUE AND
THAT IT IS REGULATING CORRECTLY. WE SUGGEST THAT YOU AND YOUR
SERVICE ORGANIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE
REGULATION IS ALWAYS CHECKED AS A STANDARD SERVICING
PROCEDURE, AND THAT THE HIGH VOLTAGE READING BE RECORDED ON
EACH CUSTOMER’S INVOICE.

5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN A
PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE, AVOID BEING
UNNECESSARILY CLOSE TO THE PICTURE TUBE AND THE HIGH VOLTAGE
SUPPLY. DO NOT OPERATE THE PRODUCT LONGER THAN IS NECESSARY
TO LOCATE THE CAUSE OF EXCESSIVE VOLTAGE.

6. REFER TO HV, B+ AND SHUTDOWN ADJUSTMENT PROCEDURES
DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS (WHERE
USED).

SUBJECT : IMPLOSION

1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTEGRA
IMPLOSION PROTECTION SYSTEM. BUT CARE SHOULD BE TAKEN TO
AVOID DAMAGE DURING INSTALLATION. AVOID SCRATCHING THE TUBE.
OF SCRATCHED REPLACE IT.

2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.

SUBJECT : TIPS ON PROPER INSTALLATION

1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBYHOLE OR
CLOSELY FITTING SHELF SPACE, OVER OR CLOSE TO HEAT DUCT, OR IN
THE PATH OF HEATED AIR FLOW.

2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO
INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS
WHERE STEAM LEAKAGE IS A FACTOR, ETC.

3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT REAR VENTING.
THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE
SCARVES OR OTHER COVERINGS WHICH MIGHT OBSTRUCT VENTILA­TION.

4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL
MOUNTING KIT, MUST FOLLOW THE FACTORY APPROVED MOUNTING
INSTRUCTIONS. A PRODUCT MOUNTED TO A SHELF OR PLATFORM MUST
RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN SPAC­ERS)TO PROVIDE ADEQUATE AIR FLOW ACROSS THE BOTTOM, BOLTS OR
SCREWS USED FOR FASTENERS MUST NOT TOUCH ANY PARTS OR
WIRING. PERFORM LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.

5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON
SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS
PROPERLY SECURED.

6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS MOUNT­ING TO THE CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRY­ING TO ROLL A CART WITH SMALL CASTERS ACROSS THRESHOLDS OR
DEEP PILE CARPETS.

7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND WHICH
HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES. INC. FOR
USE WITH THEIR SPECIFIC MODEL OF TELEVISION RECEIVER OR
GENERICALLY APPROVED FOR USE WITH T.V.S OF THE SAME OR LARGER
SCREEN SIZE.

8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS,
EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE
OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO HOME AND
FAMILY.

THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE SERVICE PERSONNEL TO THE PRES-ENCE
OF UNINSULATED “DANGEROUS VOLTAGE”
THAT MAY BE OF SUFFICIENT MAGNITUDE TO CON­STITUTE A RISK OF ELECTRIC SHOCK.

THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE SERVICE
PERSONNEL TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION ON SERVICE LITERATURE.

SUBJECT : GRAPHIC SYMBOLS

10WATT

GOOD EARTH GROUND

SUCH AS THE WATER
PIPE, CONDUIT, ETC.

1500 OHM

A.C. VOLTMETER

PLACE THIS PROBE
ON EACH EXPOSED
METAL PART

0.15 uF

-3-

SAFETY PRECAUTIONS

CAUTION : Do not attempt to modify this product in any way. Unau­thorized modifications will not only void the warranty, but may lead to your
being liable for any resulting property damage or user injury.
Service work should be performed only after you are thoroughly familiar
with all of the following safety checks and servicing guide-lines. To do
otherwise, increases the risk of potential hazards and injury to the user.

SAFETY CHECKS

After the original service problem has been corrected, a check should be
made of the following:

SUBJECT : FIRE & SHOCK HAZARD

1. Be sure that all components are positioned in such a way as to avoid
possibility of adjacent component shorts. This is especially important on
those chassis which are transported to and from the repair shop.

2. Never release a repair unless all protective devices such as insula-tors,
barriers, covers, shields, strain reliefs, and other hardware have been
reinstalled per original design.

3. Soldering must be inspected to discover possible cold solder joints,
frayed leads, damaged insulation (including A.C. cord), solder splashes
or sharp solder points. Be certain to remove all loose for-eign particals.

4. Check for physical evidence of damage or deterioration to parts and
components, and replace if necessary follow original layout, lead length
and dress.

5. No leads or components should touch a receiving tube or a resistor
rated at 1 watt or more. Lead tension around protruding metal sur-faces
must be avoided.

6. All critical components such as fuses, flameproof resistors, capaci-tors,
etc. must be replaced with exact factory types. Do not use replacement
components other than those specified or make unrecommended circuit
modifications.

7. After re-assembly of the set always perform an A.C. leakage test on all
exposed metallic parts of the cabinet, (the channel selector knob,
antenna terminals, handle and screws) to be sure the set is safe to
operate without danger of electrical shock. Do not use a line isolation
transformer during this test. Use an A.C. voltmeter, having 5000 ohms
per volt or more sensitivity, in the following manner : connect a 1500
ohm 10 watt resistor, paralleled by a 15 mfd. 150V A.C. type capacitor
between a known good earth ground (9water pipe, conduit, etc.) and
the exposed metallic parts, one at a time. Measure the A.C. voltage
across the combination of 1500 ohm resistor and 0.15 MFD capacitor.
Reverse the A.C. plug and repeat A.C. voltage measurements for each
exposed metallic part. Voltage measured must not exceed 0.75 volts
R.M.S. This corresponds to 0.5 milliamp A.C. Any value exceeding this
limit constitutes a potential shock hazard and must be corrected imme­diately.

The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the service personnel to the presence of uninsu­lated “dangerous voltage” that may be of suffi­cienty magnitude to constitute a risk of electric
shock.

The exclamation point within an equilateral tri­angle is intended to alert the service personnel
to the presence of important safety information
in service literature.

Fuse symbol is printed on pcb adjacent to the
fuse, with “RISK OF FIRE REPLACE FUSE AS
MARKED”. The symbol is explained in the ser­vice manual with the following wording or equiv­alent.

“CAUTION : FOR CONTINUED PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH SAME TYPE (4A, 125V)” and
“ATTENTION: AFIN D’ASSU UNE PROTECTION PERMANENTE
CONTRE LES RISQUES D’INCENDIE, REMPLACER UNIQUE-MENT
PAR UN FUSIBLE DE MEME TYPE ET DE ”4A, 125V”.

SUBJECT : X-RADIATION

1. Be sure procedures and instructions to all service personnel cover
the subject of X-rays in current T.V. receivers is the picture tube.
However, this tube does not emit X-rays when the high voltage is at
the factory specified level. The proper value is given in the appli­cable schematic. Operation at higher voltages may cause a failure
of the picture tube or high voltage supply and, under certain cir­cumstances, may produce radiation in excess of desirable levels.

2. Only factory specified C.R.T. anode connectors must be used.
Degaussing shields also serve as X-ray shield in color sets. Always
re-install them.

3. It is essential that the serviceman has available an accurate and
reliable high voltage meter. The calibration of the meter should be
checked perio - dically against a reference standard. Such as the
one available at your distributor.

4. When the high voltage circuitry is operating properly there is no
possibility of an X-radiation problem. Every time a color chassis is
serviced, the brightness should be run up and down while monitor­ing the high voltage with a meter to be certain that the high voltage
does not exceed the specified value and that it is regulating cor­rectly. We suggest that you and your service organization review
test procedures so that voltage regulation is always checked as a
standard servicing procedure. And that the high voltage reading be
recorded on each customer’s invoice.

5. When troubleshooting and making test measurements in a receiver
with a problem of excessive high voltage, avoid being unnecessarily
close to the picture tub eand the high voltage compartment. Do not
operate the chassis longer than is necessary to locate the cause of
excessive voltage.

6. Refer to HV, B+and Shutdown adjustment procedures described in
the appropriate schematic and diagrams(where used).

10WATT

GOOD EARTH GROUND

SUCH AS THE WATER
PIPE, CONDUIT, ETC.

1500 OHM

A.C. VOLTMETER

PLACE THIS PROBE
ON EACH EXPOSED
METAL PART

0.15 uF

-4-

SAFETY PRECAUTIONS

SUBJECT : IMPLOSION

1. All direct viewed picture tubes are equipped with an integral implo­sion protection system, but care should be taken to avoid damage
during installation. Avoid scratching the tube. If scratched, replace it.

2. Use only recommended factory replacement tubes.

SUBJECT : TIPS ON PROPER INSTALLATION

1. Never install any receiver in closed-in recess, cubbyhole or closely
fitting shelf space over, or close to heat duct, or in the path of
heated air flow.

2. Avoid conditions of high humidity such as : Outdoor patio installa­tions where dew is a factor. Near steam radiators where steam
leakage is a factor, etc.

3. Avoid placement where draperies may obstruct rear venting. The
customer should also avoid the use of decorative scarves or other
coverings which might obstruct ventilation.

4. Wall and shelf mounted installations using a commercial mounting
kit, must follow the factory approved mounting instructions. A
receiver mounted to a shelf or platform must retain its original
feet(or the equivalent thickness in spacers) to provide adequate are
flow across the bottom, bolts or screws used for fasteners must not
touch and parts or wiring. Perform leakage test on cus-tomized
installations.

5. Caution customers against the mounting of a receiver on sloping
shelf or a tilted position, unless the receiver is properly secured.

6. A receiver on a roll-about cart should be stable on its mounting to
the cart. Caution the customer on the hazards of trying to roll a cart
with small casters across thresholds or deep pile carpets.

7. Caution customers against the use of a cart or stand which has not
been listed by underwriters laboratories, inc. For use with their
specific model of television receiver or generically approved for use
with T.V.’s of the same or larger screen size.

-5-

SPECIFICTION

Model

DTQ-21U6SSV DTQ-21D7SSPV DTQ-2130SSFV

Item

DTQ-21U6SSFV

DTQ-20S1SSFV
CHASSIS CN-402FN
TV Standard NTSC-M
Power Input AC 120V, 60Hz AC 220V, 60Hz AC 100-250V, 60Hz
Power Consumption 70W
Tuning System Frequency Synthesizer(FS) Tuning System
Tuning Ranges TV VHF(L) : CH2 - CH6

UHF(H) : CH7 - CH13
UHF : CH14 - CH69

CATV VHF(L) : 5A, A,B,A-5-A-1,CH2-CH6

VHF(H) : C-W+11,CH7 - CH13

UHF : W+12-W+84”
Sound Output 3W + 3W
Speaker 8 ohm 7W x 2EA
Antenna Input Impedance 75 ohm Unbalanced

Auxiliary Input Terminal Front : Video, Audio(L,R) - AV2

Rear : Video, Audio(L,R) - AV1
Auxiliary Output Terminal Rear : Video, Audio(L,R) - MONITOR OUT
Intermediate Frequencies Picture IF Carrier Frequency : 45.75MHz

Sound IF Carrier Frequency : 41.25MHz

Color Sub-Carrier Frequency : 3.579545MHz
Remote Control R-48C04(AAA)
Special Function 1) Closed Caption

2) V-Chip

3) Channel Label

-6-

CIRCUIT BLOCK DIAGRAM

CN-402FN 21" MODEL for US(With Component Input)

3W 8 ohm

3W 8 ohm

21"

+122V

+195V

+47V

+14V

+47V

+44V

195V

+122V

+44V

7.7V/5V

-7-

ALIGNMENT INSTRUCTION

Your Remote Control(R-48C04)

1. POWER

Use this button to turn your TV on or off.

2. MUTE

Use to turn the TV’s sound on and off.

3. WCHV

Use these buttons to change channels on your
TV, or select items in the menu system.

4. C

VOL

B

Use these buttons to change your TV's vol­ume, to activate selections in the menu sys­tem, or to change audio and video settings.

5. MENU

Use this button to turn the TV’s menu system
on and off.

6. DISPLAY

Use this button to display the present status.

7. INPUT

Use this button to select the TV’s signal source.

8. VIDEO

Use this button to display video adjustment
items.

9. 0-9

Use these buttons to change channels.

10. SLEEP

Use this button to program the TV to turn off
after a certain time.

11. PREVIOUS

Use this button to return to the previous chan­nel you were watching.

-8-

ALIGNMENT INSTRUCTION

1. SERVICE MODE ADJUSTMENTS
Follow the steps below whenever service adjustment is required.
See Table- A and Table- B to determine if service adjustments are required.

1) How to enter the service mode using the user remote control.

- Turn the set on.

- Direct the remote control to the reception window of TV.

- Push buttons of remote control in sequence as follows.

1 →→MUTE →→DISPLAY →→MUTE

- Then, the screen will appear as follows.

SERVICE 02
SERVICE 03
SERVICE 04
SERVICE 05
SERVICE 06
SERVICE 07
SERVICE 08
SERVICE 09
SERVICE 10
SERVICE 11
SERVICE 12

VWSELECT CBADJUST L EXIT

- Using the channel up or channel down button, select the item you wish to adjust.
(The color of selected item turns into the blue.)

-

Press the volume up or down button to enter in the service mode you wish to adjust.

2) How to memorize the adjusted values in the service mode.

- Don’t have to press any button the state which the screen is displaying each of
service menus after all adjustments are completed each of all service menu.

Table-A : Adjust the values of service mode when a part is replaced.

PART ADJUSTMENT

NOTES

REPLACED NECESSARY UNNECESSARY

I701 O Data is stored in I702.

(U-COM)

Initial setting values are written from I701.

I702 ADJUSTING ITEMS

(EEPROM) O S6 : Geometry adjustmrnt

S8 : White balance
S9 : Subbrightness

Adjust items related to picture tube only.

CRT O (White Balance adjustment)

CRT OPTION (Screen Option adjustment)

-9-

ALIGNMENT INSTRUCTION

MODE NAME VAL REMARKS MODE NAME VAL REMARKS

S1 HEAT RUN RUN OFF SOC 0

PWLDAC 0

CL 4

S5 AGC LEVEL 22 CLD 0

IFOFF 37 GAM 1

QSS 1 HCT 0
BPB 1 ACL 0

FMI 1 BPS 0

AGN 0 CHSE 2

BPBS 1 FCO 0

DSG RF:0, AV:1 CBPS 0

Fine Tunning CB 0

FILTBW 0 MUS 0

IDMOD 1 FFI 0

OVMTHR 1 R-GAIN 32

IDMOD SLOW KOR 1 G-GAIN 32

V.SIZE 31 B-GAIN 40

V.CENTER 36 R-BIAS 32

V.SLOPE 33 G-BIAS 32

V.LINEARITY 35 SRC R-BIAS 32

S_CORRECTION 20 SRC G-BIAS 32

H.CENTER 45 CVI R-BIAS 0

H.SIZE 54 CVI G-BIAS 0

H.PARALLEL 44 DP-Brightness 10

H-BOW 35 DP-Contrast 10

PARABOLA 17 DP-Color 5

EW TRAPEZ 38 DP-Sharpness 18

CORNER TOP 54 S10 OPTION

CORNER BOTTOM 46 S12 FACTORY SET

CFCLF 1

YD TV RF:4, AV:7

DTR 0

BPYD 0

TCCON 1

TCI2X 0

PF 3

TFR 1

NRR 0

WS 3
BLS 0
DSK 0
AAS 2
BSD 0
BKS 1
DSA 0
RPO 3
RPA 2
BPD 0

CFA0 1

S9

S8

S6

S7-1

S7-2

DTQ-20S1SSFV EEPROM DATA (050407)

CN-402FN

SCREEN ADJUSTS2 580V

* VOLUME : CENTER (32)

* OPTION 1 : 1110 1001
OPTION 2 : 0110 0011
OPTION 3 : 0000 0010

* SCREEN : 6AE ---> 18 (HEX)

-10-

ALIGNMENT INSTRUCTION

2. ASSEMBLY ADJUSTMENTS

1) SCREEN ADJUSTMENT (S2)
Enter the service mode and select service adjustment S2.

You can see the one horizontal line on the screen.
Adjust the Screen Control Volume (located on FBT) so that the horizontal line

onscreen may be disappeared.

Press S2 button to exit in the screen adjustment mode.

2) FOCUS ADJUSTMENT
Turn in a local station and adjust the Focus Control knob (located on FBT) for best

picture details at high light condition.

3) AGC ADJUSTMENT
Adjust the antenna signal level at 60 dBuV

Tune a colour bar pattern.
Find the

"AGC"

item in service mode.

(it's two way to entering the

"AGC"

item in service mode)

- Enter the service mode and select service adjustment S5 and select AUTO-AGC.

- Enter the service mode and select service adjustment S3.

Wait until AGC level stabilise to the optimum value.
Alternatively,

Enter the service mode and select service adjustment S5 and select AGC LEVEL.

Use "Vol Up/Dwn" keys to adjust manually to the desired Tuner Take Over Point.

4) GEOMETRIC ADJUSTMENTS (S6)
Select service adjustment S6

You can see the OSD as shown in below.

V.SIZE 43 H.PARALLEL 33
V.CENTER 42 H-BOW 35
V.SLOPE 28 PARABOLA 17
V.LINEARITY 37 EW TRAPEZ 38

32 CORNER TOP 54
H.CENTER 45 CORNER BOTTOM 46
H.SIZE 54

SELECT ADJUST EXIT

S_CORRECT

-11-

ALIGNMENT INSTRUCTION

4-1) Vertical Position Adjustment.

- Select V.SLOPE item, adjust V.SLOPE data value till the horizontal line in the centre of the
video signal is just at the position where the blanking stars.

- Select V.CENTER item, adjust V.CENTER data value to center the raster properly on the screen.

4-2) Vertical Size Adjustment

- Select V.SIZE item, adjust V.SIZE data value to proper vertical size as follows.

4-3) Horizontal Position Adjustment

- Select H.CENTER item, adjust H.CENTER data value to obtain proper horizontal centering of
the internal cross pattern at the left and right of the screen.

-12-

ALIGNMENT INSTRUCTION

H.PARALLEL

4-4). H.BOW, PARABOLA Adjustment
* Adjust the H.BOW, PARABOLA to compensate for geometrical distortion.
* You can not adjust the H.PARALLEL, H.SIZE, EW TRAPEZ, CORNER TOP and CORNER BOTTOM.

-13-

ALIGNMENT INSTRUCTION

5) WHITE BALANCE ADJUSTMENT(S8)
Receive a good local channel.

Enter the service mode and select service adjustment S8.
You can see the OSD as shown in below.

R-GAIN 32 SRC R-BIAS 32

G-GAIN 32 SRC G-BIAS 32

B-GAIN 40 CVI R-BIAS -8
R-BIAS 32 CVI G-BIAS 10
G-BIAS 32

Using volume up or volume down, adjust service adjustment data of R-GAIN/G-GAIN/B-GAIN and

R-BIAS/G-BIAS until a good gray scale with normal whites is obtained.ALIGNMENT INSTRUCTIONS

6) DIGITAL PRESET(D.P) ADJUSTMENTS(S9)

SUBBRIGHTNESS ADJUSTMENT

Receive a good local channel.
Enter the service mode and select service adjustment S9.
You can see the OSD as shown in below.

s

10
DP-Contrast 10
DP-Color 5

s

18

Select DP-Brightness item, adjust DP-Brightness data value to obtain normal

brightness level.

DP-Contrast

Fixed value = 10

DP-Color

Fixed value = 5

DP-Sharpness

Fixed value = 18

7) FACTORY OUTGOING MODE (S12 : FACT)
If you select the S12, then the set becomes factory outgoing status.

You can see the OSD

"SHIPPING OFF"

SELECT ADJUST EXIT

SELECT ADJUST EXIT

DP-Brightnes

DP-Sharpnes

-14-

IC DESCRIPTION

1-1. UOC III BLOCK DIAGRAM

1. UOC III SERIES

-15-

IC DESCRIPTION

1-2. UOC III FEATURES

-16-

IC DESCRIPTION

-17-

IC DESCRIPTION

-18-

IC DESCRIPTION