DAEWOO 14C4T, 14C5, 14C5T, 14U1, 14V1 Service manual & schematics

...

Page 1

April 2000

Service Guide

Colour Television CHASSIS : CP-005 Model : DTP-14V1/V2/V3/V5/C3/C4/C5TF 20V1/V3/C4/C5TF 21V1/V2/V4/V6/C6TF

		Land,		14
14/20/21 V1	14/21 V2	14/20	/3	21 V4
14 V5	14 C3	14/20		14/20 C5
21 C6
If you need further about this model, P	information ( IC, ease visit our web	Circuit descriptio o site.( http://svc.o	ns or troubleshoo lwe.co.kr)	oting)
Specifications
ITEM	DTP-14V1TF DTP-14V2TF DTP-14V3TF DTP-14V3TF DTP-14C3TF DTP-14C4TF DTP-14C5TF	DTP-20V1TF DTP-20V3TF DTP-20C4TF DTP-20C5TF	DTP-21V1TF DTP-21V2TF DTP-21V4TF DTP-21V6TF DTP-21C6TF	REMARKS
CCIR STANDARD		BG, D/K, I/I, H, L/L	1
COLOR STANDARD	PAL	/ SECAM / NTSC(AV	only)
POWER INPUT		AC 230V, 50Hz
POWER CONSUMPTION	57 W	70 W	73 W
TUNING SYSTEM	Frequency	y Synthesizer (FS) Tur	ning System
RECEPTION CHANNEL	BAND I : CH2 - BAND II : CH5 - CABLE BAND : HYPER BAND : BAND IV, V : CH	BAND I : CH2 - CH4 BAND II : CH5 - CH12 CABLE BAND : S1' - S3', S1 - S20 HYPER BAND : S21 - S41 BAND IV, V : CH21 - CH69 (CH 70 for Italy)
SOUND OUTPUT
SPEAKER		3 W 8 ohm
ANTENNA INPUT
AUXILIARY TETMINAL	INPUT : RCA J. SCAR
REMOTE CONTROL		R-40A01
SPECIAL FUNCTION	14 - Language OSD With TELETEXT Wake-up On Time Sleep Timer
	DAFWOO	FI FCTR	ONICS C

http://svc.dwe.co.kr

Page 2

Important Service Notes

1. X-ray Radiation Rrecaution

Excessive high voltage can produce potentially hazardous X-RAY RADIA-TION. To avoid such hazards, the high voltage must not be above the specified limit. The nominal value of the high voltage of this receiver is 25.5kv(20"/21") & 23.5kv(14")at zero beam current (minimum brightness) under a 120V/220V AC power source. The high voltage must not, under any circumstances, exceed 28kv(20"/21") & 26kv(14"). Each time a receiver requires servicing, the high voltage should be checked following the HIGH VOLTAGE CHECK procedure on page 10 of this manual. It is recommended as a parts of the service record. It is important to use an accurate and reliable high voltage meter.
2) This receiver is equipped with X-RADIATION PROTECTION circuit which prevents the receiver from producing an excessively high voltage even if the B+voltage increases abnormally. Each time the receiver is serviced, X-RADIATION PROTECTION circuit must be checked to determine that the circuit is properly functioning, following the X-RADIATION PROTECTION CIRCUIT CHECK procedure on page 6 of this manual.
3) The only source of X-RAY RADIATION in this TV receiver is the picture tube. For continued X-RAY RADIATION protection, the replacement tube must be exactly the same type tube as specified in the parts list.
4) Some parts in this receiver have special safety-related characteristics for X-RAY RADIATION protection. For continued safety, parts replacement should be undertaken only after referring to the PRODUCT SAFETY NOTICE below.

2. Safety Precaution

WARNING : Service should not be attempted by anyone unfamiliar with the necessary precaution on this receiver. The following are the necessary precaution to be observed before servicing.

Since the chassis of this receiver has hazardous potential to ground whenever the receiver is plugged in (floating chassis), an isolation transformer must be used during servicing to avoid shock hazard.
2) Always discharge the picture tube anode to the CRT conductive coating the picture tube. The picture tube is highly evacuated and if broken, glass fragments will be violently expelled. Use shatterproof goggles and keep picture tube away from the body while handling.
3) When placing chassis in the cabinet, always be certain that all the protective devices are put back in place, such as; nonmetallic control knobs, insulating covers, shields, isolation resistor-capacitor network, etc.
4) Before returning the set to the customer, always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, screw-heads, metal overlays, control shafts etc. to be sure the set is safe to operate without danger of electrical shock. Plug the AC line cord directly into a 120V AC outlet (do not use a line isolation transformer during this check). Use an AC voltmeter having 5000 ohms per volt or more sensitivi-ty in the following manner.

Connect at 1500 ohm 10 watt resistor, paralleled by a 0.15 mfd. AC type capacitor, between a known good earth ground (water pipe, conduit etc.) and the exposed metallic parts, one at a time. Measure the AC voltage across the combination of 1500 ohm resistor and 0.15 mfd capacitor. Voltage measured must not exceed 0.3 volts RMS. This corresponds to 0.2 mill-liamp. AC. Any value exceeding the limit constitutes a potential shock hazard and must be corrected immediately.

3. Product Safety Notice

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by shading on the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create X-ray radiation or other hazards.

4. Service Notes

1) When replacing parts or circuit boards, clamp or bend the lead wires to terminals before soldering.
2) When replacing a high wattage resistor (metal oxide film resistor) in the circuit board, keep the resistor min 1/2 inch away form circuit board.
3) Keep wires away from high voltage or high temperature components.

DAEWOO ELECTRONICS CO., LTD.

C.P.OBOX8003 SEOUL, KOREA Tel : 82-2-360-7798 Fax : 82-2-360-7877 E-mail : G7F00E@dwe.web.co.kr Printed in Apr. 2000

Page 3

Alignment Instructions

SVC v0
R BIAS	159
G BIAS	136
B BIAS	127
R DRIVE	35
G DRIVE	31
B DRIVE	32
V. CENTER	10
V. SIZE	23
H. CENTER	28
VCO	07
VCO FIN	107
VCO-L	05
VCO-L FIN	113
AGC	NO
LED EAST	44
Pr	01

ENTER SERVICE MODE

1. Select the Pr 91.

Adjust "Sparpness "to 0. Enter the service mode

using the follow keys.

R→ G→ MÉNU

1. AFT

1) Set a signal Generator with
- RF FREQUENCY = 38.9MHz, 34.2MHz (L')
- RF OUTPUT LEVEL = 80+/-5dBuV
- System = PAL for 38.9MHz. SECAM-I for 43.2MHz
2) Connect the Signal Generator RF Output (PAL 38.9MHz) to P101 (Tuner IF Output). There must be no signal input to the tuner.
Locate the cusor to "VCO" in Service Mode Menu then press the "Vol +" key and wait until the "Please wait" disappear on the TV screen.
4) Connect the Signal Generator RF Output (SECAM-I_34.2MHz) to P101 (Tuner IF Output).
5) Locate the cusor to "VCO-L" in Service Mode Menu, then press the "Vol +" key and wait until the "Please wait" disappear on the TV screen.

2. SCREEN

1) Receive the Retma pattern and heat run over 15minutes. 2) Adjust the "R. G BIAS. R. G DRIVE" to 0. "B BIAS" to

127, "B DRIVE" to 32. Adjust the screen volume that the Retma pattern reachs

Adjust the screen volume that the Reima pattern reachs the cut-off point.

3. WHITE BALANCE

1) Receive the Full white pattern and heat run over 15minutes.
2) Adjust the picture control at the point "X" value of white balance instrument in 20cd/m
3) Enter the service mode
4) Adjust "R BIAS, G BIAS" to x=288, y=301.
5) In order to exit the service mode power off the TV set and power on.
6) Set the TV set to "Normal I" mode(20/21 inch) or set to "Normal II" mode(14 inch)
7) Enter the service mode.
8) Adjust "R DRIVE, G DRIVE" to x=288, y=301.
9) Repeat above process until the white balance value to x=288, y=301, X=20, x=288, y=301, X=200 (approximate) in 2) -8)

4. FOCUS

1) Apply a RETMA PATTERN signal.
2) Adjust the Focus Volume on FBT to obtain optimal resolution.

5. AGC

1) Set a pattern Generator with
- RF LEVEL = 60dBuV
- 100% FULL COLOR BAR
2) Connect the Pattern Genetator RF Output to tuner RF input.
3) Connect the probe of oscilloscope in AGC pin of tuner.
4) Adjust the AGC point to MAX 1V.

(Simple Method)

1) Receive the pattern.
2) Locate the cusor in "AGC" and adjust using the

"VOL +" or "VOL -" keys.

Adjust the point there is no noise in about 60dBuV and no beat in about 90dBuV.

Page 4

6. GEOMETRY

6.1 VERTICAL CENTER

Set the TV to "NORMAL I" mode. Enter the service mode.

Locate the cusor at "V.CENTER" then press "VOL +" or "VOL -" keys to adjust the center line with the mechanical center marks of the CRT.

6.2 VERTICAL SIZE

* The VERTICAL CENTER adjustment has to be done in advance. 1) Receive the Retma pattern. 2) Set the TV to "NORMAL I" mode. 3) Enter the service mode. 4) Locate the cursor at "V.SIZE" then press "VOL +"

or "VOL -" keys to adjust the upper part of the picture.

6.3 HORIZONTAL CENTER

Apply a RETMA PATTERN signal. Set the TV to "NORMAL I" mode. Enter the service mode. Locate the cursor at "H.CENTER" then press "VOL +" or "VOL -" keys to adjust the picture centering.

if EEPROM(I702) has been changed;

Option data has to be change and
all alignment function has to be readjusted

* The initial state of adjustment are as follows;

V-Center, V-Size, H-Center, R, G, B, AFT = Center (
AGC =

* Service Remocon

Page 5

Floctric	ol Do	rte Lict									LOC	PART CODE	PART NAME	PART DESCRIPTION	LOC	PART CODE	PART NAME	PART DESCRIPTION	LOC	PART CODE	PART NAME	PART DESCRIPTION
	агга										D107	DUZ5R1B	DIODE ZENER	UZ-5.1B UNIZON	L603	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN	R501	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J
			R	is a recor	mmendable	part for stock.					D301,3	D1N4937G	DIODE	1N4937G (TAPPING)				COATING	R502	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J
			آ	is safety	component	, so it must be used	the sam	e compoi	nent.		D402~3	DIN4937G	DIODE	IN4937G (TAPPING)	L604	5CPZ109M02	COIL PEAKING	1UH M (AXIAL 3.5MM)	R503	RN01B300JS	R METAL FILM	1W 30 OHM J SMALL
					1	/		1			D404	DUG3			L606	85801065GY	WIRE COPPER	AWG22 I/0.65 TIN	R512	RD-4Z/50J-	R CARBON FILM	1/4 /5 OHM J
LOC PART CODE		PART DESCRIPTION	LOC	PART CODE	PARTNAME	PART DESCRIPTION	LOC	PART CODE	PARTNAME	PART DESCRIPTION	D410	D1N/1/8			1 701	5CD7100K02			R521	RD-4Z101J-		1/4 100 OHM J
ZZ100 (® 48B3740A01	TRANSMITTER	R-40A01	C410	CMXM2A104J	C MYLAR	100V 0.1MF J (TP)	C828	CEXF1C101V	C ELECTRO	16V RSS 100MF	D450	D1N4140	DIODE		1702	5CP2100K02			R020	RD-4Z104J-
	REMOCON		C411	CMYN1J105K	C MYLAR (MKT)	63V 1MF K (7.5MM)				(6.3X11) TP	D432	DII75R6RM-			L/02	500000003		DS208	R320	RD-4Z 102J-		1/4 TK OHM J
22110 PTACPWA627	ACCESSURY AS	DIP-14C51F	C420	CEXF1C4/0V	CELECTRO	16V RSS 4/MF (5X11) TP	C829	CEXF1H100V	CELECTRO	50V RSS 10MF (5X11) TP	D508	D1N4148		1N4148 (TAPPING)	1.801	5PL F2443		1 E-24A3	R601	RD-271021-		1/2 1K OHM I
100 4650Q00910			C421	CEXF2E330V	C ELECTRO	250V RSS 33MF (13X25) TP	C830	CEXF1C471V	C ELECTRO	16V RSS 4/UMF	D509	D1N4148	DIODE	1N4148 (TAPPING)	1.802	5MC0000100	COIL BEAD	HC-3550	R602	RD-475111-	R CARBON FILM	1/4 510 OHM 1
77120 PTBCSH4627	COVER BACK AS	DTP-14C5TE	C501			50V R55 0.47/WF (5ATT) TP	C941	CCVE1U1027	C CEDA		D510	DUZ5R1B	DIODE ZENER	UZ-5.1B UNIZON	L803	5MC0000100	COIL BEAD	HC-3550	R611	RD-4Z362J-	R CARBON FILM	1/4 3.6K OHM J
M211 4852151401	COVER BACK		C502	CEXE1C470V		161/ DSS 47ME (5Y11) TD	C841	CCYR3A102K	C CERA	1KV B 1000PE K (TAPPING)	D512~4	D1N4148	DIODE	1N4148 (TAPPING)	L805	58C4500079	COIL CHOKE	L-45	R715	RD-4Z102J-	R CARBON FILM	1/4 1K OHM J
M541 4855415800	SPEC PLATE	150ART P/F FILM (C/TV)	C504	CEXD1H229E	C ELECTRO	50V RND 2 2MF (5X11) TP	C850	CEXE1C470V	C ELECTRO	16V RSS 47ME (5X11) TP	D602	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	L806	5CPZ390K04	COIL PEAKING	39UH 10.5MM K (LAL04TB)	R723	RD-4Z332J-	R CARBON FILM	1/4 3.3K OHM J
ZZ130 PTPKCPA627	PACKING AS	DTP-14C5TF	C506	CEXD1H229F	C FLECTRO	50V RND 2.2MF (5X11) TP	C902	CMXI 2F104K	C MYLAR	250V MEU 0.1ME K	D610	D1N4148	DIODE	1N4148 (TAPPING)	M681	4856812001	TIE CABLE	NYLON66 DA100	R735	RD-4Z103J-	R CARBON FILM	1/4 10K OHM J
M801 4858038700	BOX CARTON	SW-2 DTQ-1463FW				16V RSS 100MF	C905	CMXL2E104K	C MYLAR	250V MEU 0.1MF K	D620	D1N4148	DIODE	1N4148 (TAPPING)	M721	4857235402	SHIELD CASE	SPTH-C T0.25	R736	RD-4Z224J-	R CARBON FILM	1/4 220K OHM J
M811 4858189600	PAD	EPS 14V5	C507	CEXF1C101V	C ELECTRO	(6.3X11) TP	C906	CBXB3D102K	C CERA SEMI	2KV BL(N) 1000PF K (T)	D701	DUZ3R9B	DIODE ZENER	UZ-3.9B	P401	4859240020	CONN WAFER	YFW500-05	R753	RD-4Z473J-	R CARBON FILM	1/4 47K OHM J
		L.D.P.E	C511	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	CC102	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	0.704	050010/501/		AWG22 1/0.65 TIN	P601	485923162S	CONN WAFER	YW025-03 (STICK)	R801	DEC140M290	POSISTOR	ECPCC140M290
M821 4858210600	BAG P.E	T0.03X1000X900	C512	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	CC103	HCQK101JCA	C CHIP CERA	50V CH 100PF J 2012	D704	85801065GY	WIRE COPPER	COATING	P801	4859287320	CONN WAFER	MKS2822-6-10-202	R802	RX07C339JF	R CEMENT	7W 3.3 OHM J 15MM 4P
ZZ131 48519A4710	CRT GROUND NET	1401S-1015-1P	C513~7	CEXF1H100V	C ELECTRO	50V RSS 10MF (5X11) TP	CC104	HCQK101JCA	C CHIP CERA	50V CH 100PF J 2012	D706	DLH2PR	LED BLOCK	LH-2P-R	P802	4859242220	CONN WAFER	YFW800-02	R803	RD-4Z514J-	R CARBON FILM	1/4 510K OHM J
ZZ132 58G0000084	COIL DEGAUSSING	DC-1450	C520	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	CC105	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012	D720	D1N4148	DIODE	1N4148 (TAPPING)	D001	4050700N02	CONNECTOR	YBNH250-	R804	RD-4Z514J-	R CARBON FILM	1/4 510K OHM J
ZZ140 PTCACAA627	CABINET AS	DTP-14C5TF	C522	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	CC108	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	D806	DRGP30J	DIODE	RGP30J	FAUL	40307041002	CONNECTOR	09YBNT025+ULW=300	DOVE	858010450V		AWG22 1/0.65 TIN
CRT1 (® PTRTPWA605	CRT AS	PAL 14" ITC CRT AS	C523	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	CC109	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	D808,10,	D1N4936GP-	DIODE	1N4936GP (TAPPING)	PA801 🔞	4859906210	CORD POWER AS	6-L0+H03VVH2=2200	1000	100010001	WINE OUFFER	COATING
V01 58D000082	COIL DY	ODY-M1489	C524	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	CC118	HCBK104KCA	C CHIP CERA	50V X7R 0.1MF K 2012	12	Sin Hoodi -			Q105	TKTC3198Y-	TR	KTC3198Y	R806	RD-4Z363J-	R CARBON FILM	1/4 36K OHM J
V02 48A96R004-	RUBBER WEDGE	HMR 28 SR (\|0X54)	C601	CEVELC 101V		16V RSS 100MF	CC412	HCQK160JCA	C CHIP CERA	50V CH 16PF J 2012	D816	DUZ3R9B	DIODE ZENER	UZ-3.9B	Q401	TKTC3207	TR	KTC3207 (TP)	R808	RS02Z828JS	R M-OXIDE FILM	2W 0.82 OHM J SMALL
V03 4850PM001-	MAGNET CP	NY-225 (MINI NECK)	COUT	CEAFICIUIV	CELECTRO	(6.3X11) TP	CC501	HCQK101JCA	C CHIP CERA	50V CH 100PF J 2012	D820	D1N4148	DIODE	1N4148 (TAPPING)	Q402 🔞	T2SD2499	TR	2SD2499	R809	RD-4Z103J-	R CARBON FILM	1/4 10K OHM J
V04 2TC26019BE	TAPE CLOTH	19X30 BEIGE	C602	CEXF1H108A	C ELECTRO	50V RSM 0.1MF 4X7	CC502	HCFK103ZCA	C CHIP CERA	50V Y5V 0.01MF Z 2012	D835	DR2M	DIODE ZENER	R2M	Q501	TKTC3198Y-	TR	KTC3198Y	R810	RD-4Z333J-	R CARBON FILM	1/4 33K OHM J
V05 2224050026	BOND SILICON	RTV 122 CARTRIDGE	C606	CEXE1C101V	C FLECTRO	16V RSS 100MF	CC504	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	D837~40	DLT2A05G	DIODE	LT2A05G (TP)	Q502	TKTC3198Y-	TR	KTC3198Y	R812	RC-2Z825KP	R CARBON COMP	1/2 8.2M OHM K
V06 2233030001	PAINT LOCK	3B-1401B		SEX IOIOIT	0 ELEONIO	(6.3X11) TP	CC505	HCBK222KCA	C CHIP CERA	50V X7R 2200PF K 2012	F801	5FSCB4022R	FUSE CERA	SEMKO F4AH 4A 250V	Q503	TKTA1266Y-	TR	KTA1266Y (TP)	R819	RS02Z278JS	R M-OXIDE FILM	2W 0.27 OHM J SMALL
V901 48A96414P4	CRT BARE	A34JLL90X(K)	C611	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	CC506	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012				MF51	Q505	TKTA1266Y-	TR	KTA1266Y (TP)	R823	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J
M193 ® 4851937902	BUTTON CTRL	4942102+5537501	C620	CEXF1H100V	C ELECTRO	50V RSS 10MF (5X11) TP	CC508	HCBK472KCA	C CHIP CERA	50V X7R 4700PF K 2012	F801A	4857415001	CLIP FUSE	PFC5000-0702	Q506	TKTC3198Y-	TR	KTC3198Y	R824	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J
M321 4853214800	BRKT	FR HIPS BK	C702	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	CC509~12	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	F801B	4857415001	UEAT CINK ASS:V	PFC5000-0702	Q601	TKTC3198Y-		KTC3198Y	R834	RD-4Z392J-	R CARBON FILM	1/4 3.9K OHM J
M491B ® 4854942103	BUTTON	ABS BK	C703	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	CC515~7	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	1301	1TDA1771		TDA1771	0701	TKTA1260Y-		KTA1266Y (TP)	R850	RN02B180JS		2W 18 OHM J SMALL
M561 4855621401	MARK BRAND	ABS BK	C704	CEXF1C102V	C ELECTRO	16V RSS 1000MF	CC518	HCBK222KCA	C CHIP CERA	50V X7R 2200PF K 2012	1301 (R)	4857027104		SPCC T1 0+SN	0702	TKTA12001-			R890	RU-2Z335KP
M681 4856812001	THE CABLE	NYLON66 DA100				(10X20) TP	CC519	HCFK334ZCA	C CHIP CERA	50V Y5V 0.33MF Z 2012	1301A	7174301011		TT2 RND 3X10 ME7N	0703	TKTC3108V	тр	KTC3108V	R901~3	RINUIB124J3		1/2 1 5K OHM I
77200 O DTEMS 14427		DTD 14CETE	C706	CEXF1H478V	CELECTRO	50V RSS 0.47MF (5X11) TP	00520	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	1501 ®	1STV2238DO	IC CHIP VIDEO	STV2238D	0704	TKTC3198Y-	TR	KTC3198Y	RC106	HRET6821CA	R CHIP	1/10.6.8K OHM 1 2012
M201 (85206901			C801	CL1JB3474K	C LINE ACROSS	AC250V 0.4/MF U/C/	CC521			50V X/R 4/00PF K 2012	1601 ®	1TDA7267A-	IC AMP	TDA7267A	Q705	TKTC3198Y-	TR	KTC3198Y	RC107	HRFT473JCA	R CHIP	1/10 47K OHM J 2012
77210 A PTSPPW4627	SPEAKER AS	DTP-14C5TE	C902	CCVE244727	C CEDA	1KV E 4700DE 7 (T)	00522~4			50V CH 1000PF J 2012	1701 ®	1DW195DE1Q	IC MICOM	DW92195B7T-DE1(ERP)	Q710	TKTC3198Y-	TR	KTC3198Y	RC111	HRFT511JCA	R CHIP	1/10 510 OHM J 2012
	of Entrentio	YH025-	C804	CCXF3A472Z	C CERA	1KV F 4700PF Z (T)	CC533	HCEK1047CA	C CHIP CERA	50V Y5V 0 1ME 7 2012	1702 ®	1AT24C16PC	IC	AT24C16-10PC	Q801	PTR2SW4500	HEAT SINK ASS'Y	T2SK2671 + 7174300811	RC114	HRFT432JCA	R CHIP	1/10 4.3K OHM J 2012
P601A 4850703S50	CONNECTOR	03+35098+UI W=200	C805	CEYN2G181P	C ELECTRO	400V LHS 180ME (25X35)	CC534	HCOK3001CA	C CHIP CERA	50V CH 30PE 1 2012	1703 ®	1KA7805	IC REGULATOR	KA7805	Q801 🕲	T2SK2671	FET	2SK2671	RC115	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
SP01 R 4858314010	SPEAKER	SP-5070F01 3W 8 OHM	C807	CMYU3C222J	C MYLAR	1.6KV BCP 2200PF J	CC535	HCQK300JCA	C CHIP CERA	50V CH 30PF J 2012	1704 ®	1KRT30	IC PREAMP	KRT30	Q801A	4857024500	HEAT SINK	AL EX B/K	RC301	HRFT361JCA	R CHIP	1/10 360 OHM J 2012
	PCB MAIN MANUAL		C809	CH1HFE102M	C CERA AC	4.0KV 1000PF E DG	CC536	HCQK300JCA	C CHIP CERA	50V CH 30PF J 2012	1802 ®	4850M04710	MODULE POWER	DPM001T1A	Q801B	7174300811	SCREW TAPPTITE	TT2 RND 3X8 MFZN	RC302	HRFT202JCA	R CHIP	1/10 2K OHM J 2012
ZZ290 (® PTMPMSA627	AS	DTP-14C5TF	C812	CH1HFE102M	C CERA AC	4.0KV 1000PF E DG	CC602~4	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012	1805	PTA2SW6904	HEAT SINK ASS'Y	1STV8131 + 7174301011	Q802 🕲	TKSA1013Y-	TR	KSA1013Y (TP)	RC303	HRFT562JCA	R CHIP	1/10 5.6K OHM J 2012
C101 CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP			\|	1KV R 470PF K 125	CC605	HCQK471JCA	C CHIP CERA	50V CH 470PF J 2012	1805 ®	1STV8131	IC REGULATOR	STV8131	R101	RD-4Z242J-	R CARBON FILM	1/4 2.4K OHM J	RC304	HRFT272JCA	R CHIP	1/10 2.7K OHM J 2012
C102 CEXF1H479V	C ELECTRO	50V RSS 4.7MF (5X11) TP	C814	CCYR3A471K	C CERA	DE0705	CC606	HCQK471JCA	C CHIP CERA	50V CH 470PF J 2012	1805A	4857026904	HEAT SINK	AL EX	R109	RD-4Z183J-	R CARBON FILM	1/4 18K OHM J	RC306	HRFT472JCA	R CHIP	1/10 4.7K OHM J 2012
C103 CEVE10332V		16V RSS 2200MF	015	CEVEDCIDIV		160V RSS 100MF	CC610	HCQK181JCA	C CHIP CERA	50V CH 180PF J 2012	1805B	7174301011	SCREW TAPPTITE	TT2 RND 3X10 MFZN	R110	RD-4Z102J-	R CARBON FILM	1/4 1K OHM J	RC307	HRFT562JCA	R CHIP	1/10 5.6K OHM J 2012
CIUS CEXFIC222V	GELEGIRU	(13X25) TP	C815	CEXE2C101V	U ELECTRO	(16X25) TP	CC612	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	1901	PTB3SW1100	HEAT SINK ASS'Y	1TDA6103Q- + 7174301011	R111	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J	RC308	HRFT332JCA	R CHIP	1/10 3.3K OHM J 2012
C301 CEVE11/4710		35V RUS 470MF	C816	CCXB3A471K	C CERA	1KV B 470PF K (T)	CC613	HCFK103ZCA	C CHIP CERA	50V Y5V 0.01MF Z 2012	1901 ®	1TDA6103Q-	IC VIDEO	TDA6103Q	R120	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J	RC309	HRFT154JCA	R CHIP	1/10 150K OHM J 2012
GEAL DEAL TV4/10	5 22201110	(10X20) TP	C818	CEXE2C101C	C ELECTRO	160V RUS 100MF	CC701	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	1901A	4857031100	HEAT SINK	A1050P-H24 T2.0	R301	RD-2Z249J-	R CARBON FILM	1/2 2.4 OHM J	RC310	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
C302 CCXB3A471K	C CERA	1KV B 470PF K (T)	010	SEAT 201010	JELUINU	(16X25) TP	CC702	HCQK820JCA	C CHIP CERA	50V CH 82PF J 2012	1901B	7174301011	SCREW TAPPTITE	TT2 RND 3X10 MFZN	R302	RN02B229JS	R METAL FILM	2W 2.2 OHM J SMALL	RC313	HRFT224JCA	R CHIP	1/10 220K OHM J 2012
C303 CEXF1E102C	C ELECTRO	25V RUS 1000MF	C819	CEXE2A100V	C FLECTRO	100V RSS 10MF	CC705	HCBK472KCA	C CHIP CERA	50V X7R 4700PF K 2012	J046	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J	R303	RN02B271JS	R METAL FILM	2W 270 OHM J SMALL	RC404	HRFT561JCA	R CHIP	1/10 560 OHM J 2012
		(13X20) TP				(6.3X11) TP	CC707	HCQK820JCA	C CHIP CERA	50V CH 82PF J 2012	JC001~6	HRFT000-CA	R CHIP	1/10 0 OHM 2012	R307	RN02B181JS	R METAL FILM	2W 180 OHM J SMALL	RC405	HRFT362JCA	R CHIP	1/10 3.6K OHM J 2012
C304 CEXF1H220V	C ELECTRO	50V RSS 22MF (5X11) TP	C820	CEXF1E102V	C ELECTRO	25V RSS 1000MF	CC708	HCBK472KCA	C CHIP CERA	50V X7R 4700PF K 2012	JC008~9	HRFT000-CA	K CHIP	1/10 0 OHM 2012	R308	RN02B181JS	R METAL FILM	2W 180 OHM J SMALL	RC408	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
C305 CMXE2A473J	C MYLAR	100V PU 0.047MF J				(13X20) TP	CC709	HCQK220JCA	C CHIP CERA	50V CH 22PF J 2012	JC011~20	HRF1000-CA		1/10 0 OHM 2012	R309	RNU2B181JS		2W 180 OHM J SMALL	RC419	HRF [152JCA		1/10 1.5K OHM J 2012
C306 CEXF1V101C	C ELECTRO	35V RUS 100MF	C822	CEXF1C101V	C ELECTRO	16V RSS 100MF	CC713	HCBK222KCA	C CHIP CERA	50V X7R 2200PF K 2012	JC024 5	HRETOOD CA		1/10 0 OHM 2012	R310	RNU2B181JS		2W 180 OHM J SMALL	RC420	HRF1394JCA		1/10 390K OHM J 2012
	0.00/1.17	(8X11.5) TP				(6.3X11) TP	CC722	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012	10024~5	4850100050		PH_IB-9710A	R402	RS022103JS		2W IUK OHM J SMALL	RC501			1/10 /5 OHM J 2012
C307 CMXB1H224J		SUV EU 0.22MF J (TP)	C823	CCXB3A471K	C CERA	1KV B 470PF K (T)	CC723	HCQK220JCA	C CHIP CERA	50V CH 22PF J 2012	101	58N0000044	COIL VCO	TRF-V010	R403	RD-274721			RCEO4	HRET1011CA	R CHIP
C401 CEXF1H109V		2001/ DU 0 2415	C824	CCXB3A471K	C CERA		CC801	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	1 301	5CP7100K04	COIL PEAKING	10UH 10.5MM K (LAL04TR)	R400	RD-471021			RC507	HRET1031CA	R CHIP	1/10 10K OHM 1 2012
C401 CMYE2D364J			C825	CEXE111420V		50V KS5 22MF (5X11) TP	D101	FILEEK 104ZCA		300 Y50 U.IMF Z 2012	L511	5CPZ100K02	COIL PEAKING	10UH K (AXIAL 3.5MM)	R408	RD-471021-	R CARBON FILM	1/4 1K OHM J	RC508	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
C404 CMVH3C6031	C MYLAR	1.6KV BUP 4900PF 1	6820	CEAF IH4/9V	U ELEUTRU	30V K33 4./MF (3X11) 1P		D1000ETA		1995TA	L601	5CPZ109M02	COIL PEAKING	1UH M (AXIAL 3.5MM)	R409	RD-4Z561 J-	R CARBON FILM	1/4 560 OHM J	RC509	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
		500V B 1000PF K	C827	CEXF1C222V	C ELECTRO	13X25) TP	D105	DI17328		13303TA 117.33B	L602	5CPZ109M02	COIL PEAKING	1UH M (AXIAL 3.5MM)	R410	RN01B132JS	R METAL FILM	1W 1.3K OHM J SMALL	RC510	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
C406 CCXB2H102K	C CERA					(13723) 15	D103	D1N4149				1 1	-	,,

Page 6

LOC	PART CODE	PART NAME	PART DESCRIPTION	LOC	PART CODE	PART NAME	PART DESCRIPTION
511	HRFT470JCA	R CHIP	1/10 47 OHM J 2012	RC726	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
512	HRFT223JCA	R CHIP	1/10 22K OHM J 2012	RC727	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
513	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC729	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
514	HRFT151JCA	R CHIP	1/10 150 OHM J 2012	RC730	HRFT332JCA	R CHIP	1/10 3.3K OHM J 2012
515	HRFT000-CA	R CHIP	1/10 0 OHM 2012	RC731	HRFT100JCA	R CHIP	1/10 10 OHM J 2012
516	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	RC732	HRFT000-CA	R CHIP	1/10 0 OHM 2012
517	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	RC733	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
518	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	RC736	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
519	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	RC738	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
520	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC751	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
521	HRFT363JCA	R CHIP	1/10 36K OHM J 2012	RC752	HRFT682JCA	R CHIP	1/10 6.8K OHM J 2012
522	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	RC754	HRFT333JCA	R CHIP	1/10 33K OHM J 2012
523	HRFT822JCA	R CHIP	1/10 8.2K OHM J 2012	RC755	HRFT473JCA	R CHIP	1/10 47K OHM J 2012
524	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC822	HRFT134JCA	R CHIP	1/10 130K OHM J 2012
525	HRFT153JCA	R CHIP	1/10 15K OHM J 2012	RC828	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
526	HRFT273JCA	R CHIP	1/10 27K OHM J 2012	RC829	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
527	HRFT473JCA	R CHIP	1/10 47K OHM J 2012	RC901	HRFT272JCA	R CHIP	1/10 2.7K OHM J 2012
528	HRFT221JCA	R CHIP	1/10 220 OHM J 2012	RC902	HRFT302JCA	R CHIP	1/10 3K OHM J 2012
529~31	HRFT271JCA	R CHIP	1/10 270 OHM J 2012	RC903	HRFT302JCA	R CHIP	1/10 3K OHM J 2012
532	HRFT273JCA	R CHIP	1/10 27K OHM J 2012	RC904	HRFT302JCA	R CHIP	1/10 3K OHM J 2012
534	HRFT334JCA	R CHIP	1/10 330K OHM J 2012	RC905~7	HRFT272JCA	R CHIP	1/10 2.7K OHM J 2012
535	HRFT184JCA	R CHIP	1/10 180K OHM J 2012	RI Y1	5SC0101338	SW RELAY	DO5D1-0(M)/GJ-SS-105LM
537	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	SCT1	4859303430	SOCKET CRT	PCS633A
538	HRFT223JCA	R CHIP	1/10 22K OHM J 2012	SE101	5PG3962M	FILTER SAW	G 3962-M
539	HRFT122JCA	R CHIP	1/10 1.2K OHM J 2012	SF102	5PK9650M	FILTER SAW	K9650M
541~3	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	SJ01	4859200401	SOCKET RGB	YRS21-R1
553	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	SW701	5$50101090	SW TACT	SKHV17910A
555	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	SW702	5$50101090	SW TACT	SKHV17910A
560	HRFT472JCA	R CHIP	1/10 4.7K OHM J 2012	SW703	5$50101090	SW TACT	SKHV17910A
605	HRFT153JCA	R CHIP	1/10 15K OHM J 2012	SW704	5$50101090	SW TACT	SKHV17910A
606	HRET153JCA	R CHIP	1/10 15K OHM J 2012	SW705	5$50101090	SW TACT	SKHV17910A
610	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	SW801 @	5$40101146	SW POWER PUSH	SS-160-7-B
611	HRFT152JCA	R CHIP	1/10 1.5K OHM J 2012	T401	50D10A3	TRANS DRIVE	TD-10A3
620	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	T402 R	50H0000202	FBT	FUY20C001
621	HRFT104JCA	R CHIP	1/10 100K OHM J 2012	T801	50M404245-	TRANS SMPS	TSM-404245
623	HRET512 ICA	R CHIP	1/10 5 1K OHM 1 2012	1001 11101 ®	4859719930		DT5-BE18D
630	HRET102 ICA	R CHIP	1/10 1K OHM \| 2012	0101 0	4037717730		513 51 105
702	HRET102 ICA	R CHIP	1/10 1K OHM \| 2012	W101	4851900130	AS	DS-W1015-S
703	HRET1021CA	RCHIP	1/10 1K OHM J 2012			7.5	HC 4011 4 43361M 15DDM
704	HRET5621CA	RCHIP	1/10 5 6K OHM 1 2012	X501	5XEX4R433B	CRYSTAL QUARTZ	TD
705	HRET153 ICA	RCHIP	1/10 15K OHM 1 2012				HC 4011 3 57054M 15DDM
706	HRET562 ICA	R CHIP	1/10 5 6K OHM 1 2012	X502	5XEX3R579B	CRYSTAL QUARTZ	TD
707	HRET101 ICA	R CHIP	1/10 100 OHM 1 2012	¥701	5YEY/P000C
708			1/10 1K OHM \| 2012	X/01	JAEA4R000C	CRISTAL QUARTZ	HC-490 4.00000012 (TP)
709	HRET2221CA	R CHIP	1/10 1 CONM 5 2012
710	HDET222JOA	R CHIP	1/10 2.2K OHM 1 2012
711		R CHIP	1/10 2.2K OHM J 2012
710			1/10 2.2K OHM J 2012
712	HDET101 ICA	R CHIP	1/10 100 OHM J 2012
714	HRETINGICA	R CHIP	1/10.1K OHM 1.2012
715	HDET1521CA
716	HDET2021CA
717	UDET15310A
710
720
721
721			1/10 1K OHM J 2012
122	TREISSZUCA	K UHIP	1/10 3.3K UHM 1/01/

1/10 5.5K OHM J 2012 1/10 620K OHM J 2012

Page 7

--- Video

--- Audio

Page 8

Page 9



SVC v1

R BIAS	159
G BIAS	136
B BIAS	127
R DRIVE	35
G DRIVE	31
B DRIVE	32
V. CENTER	10
V. SIZE	23
H. CENTER	28
VCO	07
VCO FIN	107
VCO-L	05
VCO-L FIN	113
AGC	44
LED EAST	NO
Pr	01
Remocon	J

ENTER SERVICE MODE

1. Select the Pr 91.
2. Adjust "Sparpness" to 0.
3. Enter the service mode using the following keys. R → G → MENU.

1. AFT

1) Set a Signal Generator with
- RF FREQUENCY = 38.9MHz, 34.2MHz (L')
- RF OUTPUT LEVEL = 80 ± 5 dBuV
- System = PAL for 38.9MHz.

SECAM-I for 43.2MHz

2) Connect the Signal Generator RF Output(PAL 38.9MHz) to P101 (Tuner IF Output). There must be no signal input to the tuner.
3) Locate the cursor to "VCO" in Service Mode Menu, then press the "Vol +" key and wait until the "Please wait" disappear on the TV screen.
4) Connect the Signal Generator RF Output(SECAM-L 34.2MHz) to P101 (Tuner IF Output).
5) Locate the cursor to "VCO-L" in Service Mode Menu, then press the "Vol +" key and wait until the "Please wait" disappear on the TV screen.

Page 10

2. SCREEN

1) Receive the Retma pattern and heat run over 15 minutes.
2) Adjust the "R, G BIAS, R, G DRIVE" to 0, "B BIAS" to 127, "B DRIVE" to 32. Adjust the screen volume that the Retma pattern reach to the cut-off point.

3. WHITE BALANCE

1) Receive the Full white pattern and heat run over 15 minutes.
2) Adjust the picture control at the point "Y" value of white balance instrument in 20cd/m².
3) Enter the service mode.
4) Adjust "R BIAS, G BIAS" to x=288, y=301.
5) In order to exit the service mode power off the TV set and power on.
6) Set the TV set to "Normal I" mode (20/21 inch) or set to "Normal II" mode (14 inch)
7) Enter the service mode.
8) Adjust "R DRIVE, G DRIVE" to x=288, y=301.
9) Repeat above process until the white balance value to x=288, y=301, Y=20, x=288, y=301, Y=200(approximate) in 2) 8).

4. FOCUS

1) Apply a RETMA PATTERN signal.
2) Adjust the Focus Volume on FBT to obtain optimal resolution.

5. AGC

1) Set the pattern Generator with
- RF LEVEL = 60dBuV
- 100% FULL COLOR BAR
2) Connect the pattern generator RF output to tuner RF input.
3) Connect the probe of oscilloscope in AGC pin of tuner.
4) Adjust the AGC point to MAX 1V.

(Simple Method)

1) Receive the pattern.
2) Locate the cursor in "AGC" and adjust using the "VOL +" or "VOL -" keys.
3) Adjust the point there is no noise in about 60dBuV and no beat in about 90dBuV.

Page 11

6. GEOMETRY

6.1 VERTICAL CENTER
- 1) Set the TV to "NORMAL I" mode.
- 2) Enter the service mode.
- 3) Locate the cursor at "V. CENTER" then press "VOL +" or "VOL " keys to adjust the center line with the mechanical center marks of the CRT.

6.2 VERTICAL SIZE

* The VERTICAL CENTER adjustment has to be done in advance.
- 1) Receive the Retma pattern.
- 2) Set the TV to "NORAML I" mode.
- 3) Enter the service mode.
- 4) Locate the cursor at "V. SIZE" then press "VOL +" or VOL -" keys to adjust the upper part of the picture.

6.3 HORIZONTAL CENTER

1) Apply a RETMA PATTERN signal.

2) Set the TV to "NORMAL I" mode.
3) Enter the service mode.
3) Locate the cursor at "H. CENTER" then press "VOL +" or VOL –" keys to adjust the picture centering.

Page 12

If EEPROM(I702) has been changed ;

Option data has to be changed and
all alignment function has to be readjusted.
* The initial state of adjustment are as follows ;
- V-Center, V-Size, H-Center, R, G, B, AFT = Center ()
- AGC =

* Service Remocon

Page 13

ST92195B

32-64K ROM HCMOS MCU WITH ON-SCREEN-DISPLAY AND TELETEXT DATA SLICER

Register File based 8/16 bit Core Architecture with RUN, WFI, SLOW and HALT modes
0°C to +70°C operating temperature range
Up to 24 MHz. operation @ 5V±10%
Min. instruction cycle time: 165ns at 24 MHz.
32, 48, 56 or 64 Kbytes ROM
256 bytes RAM of Register file (accumulators or index registers)
256 bytes of on-chip static RAM
2, 6 or 8 Kbytes of TDSRAM (Teletext and Display Storage RAM)
28 fully programmable I/O pins
Serial Peripheral Interface
Flexible Clock controller for OSD, Data Slicer and Core clocks running from a single low frequency external crystal.
Enhanced display controller with 26 rows of 40/80 characters
- Serial and Parallel attributes
- 10x10 dot matrix, 512 ROM characters, definable by user
- 4/3 and 16/9 supported in 50/60Hz and 100/ 120 Hz mode
- Rounding, fringe, double width, double height, scrolling, cursor, full background color, halfintensity color, translucency and half-tone modes
Teletext unit, including Data Slicer, Acquisition Unit and up to 8 Kbytes RAM for data storage
VPS and Wide Screen Signalling slicer (on some devices)
Integrated Sync Extractor and Sync Controller
14-bit Voltage Synthesis for tuning reference voltage
Up to 6 external interrupts plus one Non-Maskable Interrupt
8 x 8-bit programmable PWM outputs with 5V open-drain or push-pull capability
16-bit watchdog timer with 8-bit prescaler
One 16-bit standard timer with 8-bit prescaler
4-channel A/D converter; 6-bit guaranteed

Rich instruction set and 14 addressing modes
Versatile development tools, including Assembler, Linker, C-compiler, Archiver, Source Level Debugger and hardware emulators with Real-Time Operating System available from third parties
Pin-compatible EPROM and OTP devices available

Device Summary

Device	Program Memory	TDS RAM	VPS/ WSS	Package
ST92195B1	32K ROM	2K	Yes
ST92195B2	32K ROM	6K	No
ST92195B3	32K ROM	6K	Yes
ST92195B4	48K ROM	6K	Yes	PSDIP56/
ST92195B5	48K ROM	8K	Yes	TQFP64
ST92195B6	56K ROM	8K	Yes
ST92195B7	64K ROM	8K	Yes
ST92T195B7	64K OTP	8K	Yes
ST92E195B7	64K OTP	8K	Yes	CSDIP56 /CQFP64

1/202

November 1998

Page 14

1 GENERAL INFORMATION

1.1 INTRODUCTION

The ST92195 microcontroller is developed and manufactured by STMicroelectronics using a proprietary n-well HCMOS process. Its performance derives from the use of a flexible 256-register programming model for ultra-fast context switching and real-time event response. The intelligent onchip peripherals offload the ST9 core from I/O and data management processing tasks allowing critical application tasks to get the maximum use of core resources. The ST92195 MCU supports low power consumption and low voltage operation for power-efficient and low-cost embedded systems.

1.1.1 ST9+ Core

The advanced Core consists of the Central Processing Unit (CPU), the Register File and the Interrupt controller.

The general-purpose registers can be used as accumulators, index registers, or address pointers. Adjacent register pairs make up 16-bit registers for addressing or 16-bit processing. Although the ST9 has an 8-bit ALU, the chip handles 16-bit operations, including arithmetic, loads/stores, and memory/register and memory/memory exchanges.

Two basic addressable spaces are available: the Memory space and the Register File, which includes the control and status registers of the onchip peripherals.

1.1.2 Power Saving Modes

To optimize performance versus power consumption, a range of operating modes can be dynamically selected.

Run Mode. This is the full speed execution mode with CPU and peripherals running at the maximum clock speed delivered by the Phase Locked Loop (PLL) of the Clock Control Unit (CCU).

Wait For Interrupt Mode. The Wait For Interrupt (WFI) instruction suspends program execution until an interrupt request is acknowledged. During WFI, the CPU clock is halted while the peripheral and interrupt controller keep running at a frequen-

cy programmable via the CCU. In this mode, the power consumption of the device can be reduced by more than 95% (Low power WFI).

Halt Mode. When executing the HALT instruction, and if the Watchdog is not enabled, the CPU and its peripherals stop operation and the I/O ports enter high impedance mode. A reset is necessary to exit from Halt mode.

1.1.3 I/O Ports

Up to 28 I/O lines are dedicated to digital Input/ Output. These lines are grouped into up to five I/O Ports and can be configured on a bit basis under software control to provide timing, status signals, timer and output, analog inputs, external interrupts and serial or parallel I/O.

1.1.4 TV Peripherals

A set of on-chip peripherals form a complete system for TV set and VCR applications:

Voltage Synthesis
VPS/WSS Slicer
Teletext Slice
Teletext Display RAM
OSD

1.1.5 On Screen Display

The human interface is provided by the On Screen Display module, this can produce up to 26 lines of up to 80 characters from a ROM defined 512 character set. The character resolution is 10x10 dot. Four character sizes are supported. Serial attributes allow the user to select foreground and background colors, character size and fringe background. Parallel attributes can be used to select additional foreground and background colors and underline on a character by character basis.

1.1.6 Teletext and Display Storage RAM

The internal Teletext and Display storage RAM can be used to store Teletext pages as well as Display parameters.

Page 15

GENERAL DESCRIPTION (Cont'd)

1.1.7 Teletext, VPS and WSS Data Slicers

The three on-board data slicers using a single external crystal are used to extract the Teletext, VPS and WSS information from the video signal. Hardware Hamming decoding is provided.

1.1.8 Voltage Synthesis Tuning Control

14-bit Voltage Synthesis using the PWM (Pulse Width Modulation)/BRM (Bit Rate Modulation) technique can be used to generate tuning voltages for TV set applications. The tuning voltage is output on one of two separate output pins.

1.1.9 PWM Output

Control of TV settings can be made with up to eight 8-bit PWM outputs, with a maximum frequency of 23,437Hz at 8-bit resolution (INTCLK = 12 MHz). Low resolutions with higher frequency operation can be programmed.

1.1.10 Serial Peripheral Interface (SPI)

The SPI bus is used to communicate with external devices via the SPI, or I²C bus communication standards. The SPI uses a single data line for data input and output. A second line is used for a synchronous clock signal.

1.1.11 Standard Timer (STIM)

The ST92195 has one Standard Timer that includes a programmable 16-bit down counter and an associated 8-bit prescaler with Single and Continuous counting modes.

1.1.12 Analog/Digital Converter (ADC)

In addition there is a 4-channel Analog to Digital Converter with integral sample and hold, fast 5.75µs conversion time and 6-bit guaranteed resolution.

Page 16

Figure 1. ST92195 Block Diagram

Page 17

1.2 PIN DESCRIPTION

Figure 2. 64-Pin Package Pin-Out

N.C. = Not connected

Page 18

PIN DESCRIPTION (Cont'd)

RESET Reset (input, active low). The ST9+ is initialised by the Reset signal. With the deactivation of RESET, program execution begins from the Program memory location pointed to by the vector contained in program memory locations 00h and 01h.

R/G/B Red/Green/Blue . Video color analog DAC outputs.

FB Fast Blanking. Video analog DAC output.

VDD Main power supply voltage (5V10%, digital)

WSCF, WSCR Analog pins for the VPS/WSS slicer line PLL (See note 1).

MCFM Analog pin for the display pixel frequency multiplier.

OSCIN, OSCOUT Oscillator (input and output). These pins connect a parallel-resonant crystal (24MHz maximum), or an external source to the on-chip clock oscillator and buffer. OSCIN is the input of the oscillator inverter and internal clock generator; OSCOUT is the output of the oscillator inverter.

VSYNC Vertical Sync . Vertical video synchronisation input to OSD. Positive or negative polarity.

HSYNC/CSYNC Horizontal/Composite sync. Horizontal or composite video synchronisation input to OSD. Positive or negative polarity.

PXFM Analog pin for the Display Pixel Frequency Multiplier

AVDD3 Analog VDD of PLL. This pin must be tied to VDD externally to the ST92195.

GND Digital circuit ground.

AGND Analog circuit ground (must be tied externally to digital GND).

CVBS1 Composite video input signal for the Teletext slicer and sync extraction.

CVBS2 Composite video input signal for the VPS/ WSS slicer. Pin AC coupled.

AVDD1, AVDD2 Analog power supplies (must be tied externally to AVDD3 the WSCR pin is replaced by VPP which is the programming voltage).

TXCF Analog pin for the Teletext slicer line PLL.

CVBSO, JTDO, JTCK Test pins: leave floating.

JTMS, TEST0 Test pins: must be tied to AVDD2.

JTRST0 Test pin: must be tied to GND.

Note 1: The WSCF and WSCR pins are not available on all devices. On EPROM/OTP devices the WSCR pin is replaced by VPP which is the programming voltage. VPP should be tied to GND or VDD in user mode.


INT7/P2.0	1	56 P2.1/INT5/AIN1
RESET	2	55 P2.2/INT0/AIN2
P0.7	3	54 ] P2.3/INT6/VS01
P0.6	4	53 P2.4/NMI
P0.5	5	52 P2.5/AIN3/INT4/VS02
P0.4	6	51 OSCIN
P0.3	7	50 OSCOUT
AIN4/P0.2	8	49 P4.7/PWM7/EXTRG/STOUT
P0.1	9	48 P4.6/PWM6
P0.0	10	47 🛛 P4.5/PWM5
CSO/RESET0/P3.7	11	46 P4.4/PWM4
P3.6	12	45 P4.3/PWM3/TSLU/HT
P3.5	13	44 P4.2/PWM2
P3.4	14	43 P4.1/PWM1
В	15	42 P4.0/PWM0
G	16	41 VSYNC
R	17	40 HSYNC/CSYNC
FB	18	39 AVDD1
SDI/SDO/P5.1	19	38 PXFM
SCK/INT2/P5.0	20	37 JTRSTO
Voo	21	36 🛛 GND
JOOTL	22	35 🛛 AGND
*WSCF	23	34 🛛 CVBS1
*VPP/WSCR	24	33 CVBS2
AVDD3	25	32 JTMS
TESTO	26	31 AVDD2
MCFM	27
*See Note 1 of pin description. JTCK	28	29[] ТХСГ
	1

Page 19

Figure 4. ST92195 Required External components

Page 20

PIN DESCRIPTION (Cont'd)

P0[7:0], P2[5:0], P3[7:4], P4[7:0], P5[1:0] I/O Port Lines (Input/Output, TTL or CMOS com-

patible).

28 lines grouped into I/O ports, bit programmable as general purpose I/O or as Alternate functions (see I/O section).

Important : Note that open-drain outputs are for logic levels only and are not true open drain.

1.2.1 I/O Port Alternate Functions.

Each pin of the I/O ports of the ST92195 may assume software programmable Alternate Functions (see Table 1).

Table 1. ST92195 I/O Port Alternate Function Summary

Port bit	Alternate Function	Name	Function
P0.2	A/D Analog input 4	AIN4	I

P2.0	External interrupt 7	INT7	I
P2.1	External interrupt 5	INT5	I
	A/D analog input 1	AIN1	I
P2.2	External interrupt 0	INT0	I
	A/D analog input 2	AIN2	I
P2.3	External interrupt 6	INT6	I
	Voltage synthesis output1	VSO1	0
P2.4	Non-maskable interrupt	NMI	I
P2.5	Voltage synthesis output2	VSO2	0
	A/D analog input 3	AIN3	I
	External interrupt 4	INT4	I

P3.4
P3.5
P3.7	Internal reset output	RESETO	0
	Composite Sync output	CSO	0

P4.0	PWM output 0	PWM0	0
P4.1	PWM output 1	PWM1	0
P4.2	PWM output 2	PWM2	0
P4.3	PWM output 3	PWM3	0
	Translucency digital output	TSLU	0
	Half-tone output	HT	0
P4.4	PWM output 4	PWM4	0
P4.5	PWM output 5	PWM5	0
P4.6	PWM output 6	PWM6	0
P4.7	PWM output 7	PWM7	0
	External A/D trigger	EXTRG	I
	Standard timer output	STOUT	0

P5.0	External interrupt 2	INT2	Ι
	SPI serial clock	SCK	0
P5.1	SPI serial data out	SDO	0
	SPI serial data in	SDI	I

Page 21

1.2.2 I/O Port Styles

Pins	Weak Pull-Up	Port Style	Reset Values
P0[7:0]	no	Standard I/O	BID / OD / TTL
P2[5,4,3,2]	no	Standard I/O	BID / OD / TTL
P2[1,0]	no	Schmitt trigger	BID / OD / TTL
P3.7	yes	Standard I/O	AF / PP / TTL
P3[6,5,4]	no	Standard I/O	BID / OD / TTL
P4[7:0]	no	Standard I/O	BID / OD / TTL
P5[1:0]	no	Standard I/O	BID / OD / TTL

Legend:

AF= Alternate Function, BID = Bidirectional, OD = Open Drain PP = Push-Pull, TTL = TTL Standard Input Levels

How to Read this Table

To configure the I/O ports, use the information in this table and the Port Bit Configuration Table in the I/O Ports Chapter on page 68.

Port Style = the hardware characteristics fixed for each port line.

Inputs:

If port style = Standard I/O, either TTL or CMOS input level can be selected by software.
If port style = Schmitt trigger, selecting CMOS or TTL input by software has no effect, the input will always be Schmitt Trigger.

Weak Pull-Up = This column indicates if a weak pull-up is present or not.

If WPU = yes, then the WPU can be enabled/disable by software
If WPU = no, then enabling the WPU by software has no effect

Alternate Functions (AF) = More than one AF cannot be assigned to an external pin at the same time:

An alternate function can be selected as follows. AF Inputs:

AF is selected implicitly by enabling the corresponding peripheral. Exception to this are ADC analog inputs which must be explicitly selected as AF by software.

AF Outputs or Bidirectional Lines:

In the case of Outputs or I/Os, AF is selected explicitly by software.

Example 1: ADC trigger digital input

AF: EXTRG, Port: P4.7, Port Style: Standard I/O.

Write the port configuration bits (for TTL level):

P4C2.7=1

P4C1.7=0

P4C0.7=1

Enable the ADC trigger by software as described in the ADC chapter.

Example 2: PWM 0 output

AF: PWM0, Port: P4.0

Write the port configuration bits (for output pushpull):

P4C2.0=0

P4C1.0=1 P4C0.0=1

Example 3: ADC analog input

AF: AIN1, Port : P2.1, Port style: does not apply to analog inputs

Write the port configuration bits:

P2C2.1=1 P2C1.1=1 P2C0.1=1

Page 22

1801

POWER CONTROL MODULE

PIN NO	DESCRIPTION	PIN NO	DESCRIPTION
1	GATE DRIVE1	10	+12V INPUT
2	OCP	11	POWER CONTROL
3	SOURCE	12	NC
4	GND1	13	GND2
5	GATE	14	+133V INPUT
6	GATE DRIVE2

Page 23

STV223XD/223X/224X BUS CONTROLLED MULTISTANDARD ONE CHIP TV PROCESSOR

FEATURES

I²C BUS CONTROL.
PIF CIRCUIT WITH PLL DEMODULATION (Positive and Negative Video).
SIF CIRCUIT WITH QSS STRUCTURE, FM DEMODULATION AND AM DEMODULATION FOR FRANCE.
INTERCARRIER CAPABILITY.
BUILT IN SOUND BANDPASS.
SOUND SUB CARRIERS OUTPUT FOR STEREO CHASSIS (FM, Nicam).
AUDIO SWITCH AND VOLUME CONTROL (Mono Chassis).
INTEGRATED CHROMA FILTERS AND LUMA DELAY LINE.
INTEGRATED CHROMA DELAY LINE
VIDEO SWITCH (3 CVBS IN, 1 or 2 CVBS OUT).
SVHS SWITCH (Y combined with CVBS3 input).
OSD RGB INPUTS.
EXTERNAL RGB/YUV INPUTS or YUV INTERFACE.
PAL / SECAM / NTSC CHROMA DEMODULATORS.
AUTO FLESH CONTROL CAPABILITY IN NTSC.
SOUTH AMERICA CAPABILITY (PALM/PALN/ NTSC).
CHROMA SUBCARRIER OUTPUT.
BLACK STRETCH CIRCUIT.
PEAKING CIRCUIT.
AUTOMATIC CUT-OFF CURRENT LOOP.
MANUAL CUT-OFF POSSIBLE FOR LOW COST APPLICATIONS
TWO PLLs HORIZONTAL DEFLECTION.
VERTICAL COUNT DOWN.
HALF CONTRAST (optional).
APR (Automatic RGB peak regulation) FUNCTION (optional).
SAW FILTER SWITCH CONTROL (optional).
VERY FEW EXTERNAL COMPONENTS.

DESCRIPTION

The STV223XD/223X/224X are fully bus controlled ICs for TV including PIF, SIF, luma, chroma and deflection processing. Used with a vertical frame booster (TDA1771 or TDA8174 for 90° chassis, STV9306 for 110° chassis), they allow the design of multistandard (BGDKIMNLL, PAL/ SECAM/NTSC) sets with very few external components and no manual adjustments.

August 1999 - V4.2 -

This is advanced information on a new product now in development or undergoing evaluation. Details are subject to change without notice.

Page 24

Pin N°
STV224X/8X STV223X		STV223XD	Symbol	Description
SDIP56	SDIP56	TQFP64
1	1	8	SIFIN1	SIF Input
2	2	9	SIFIN2	SIF Input
3	3	10	AGCSIFCAP	AGC SIF Capacitor
4	4	11	V _REF IF	Voltage Reference Filtering
5	5	12	AGCPIFCAP	AGC PIF Capacitor
6	6	13	PIFIN1	PIF Input
7	7	14	PIFIN2	PIF Input
8	8	16	TUNERAGCOUT	AGC Tuner Output
9	9	17	IFPLL	IF PLL Filter
10	10	18	GND IF	IF Ground
11	11	19	AM/FMOUT/SC	AM/FM Mono Sound or Stereo Carriers Output
12	12	20	V _CC IF	5 V IF Supply
13	13	21	INTCVBSOUT	Internal CVBS Output
14	14	22	EXTAUDIOIN	External Audio Input
15	15	23	PIFLC1	LC Input
16	16	24	PIFLC2	LC Input
17	17	25	V _CC 2	Video/Luma Supply Voltage (8 V)
18	18	26	CVBSIN1	Internal Video Input
19	19	27	GND2	Video/Luma Ground
20	20	28	CVBSIN2	External Video Input
21	21	29	BS	Black Stretch Capacitor
22	22	34	Y/CVBSIN3	Y(SVHS) or CVBS3 External Input
23	23	35	CHR	Chroma (SVHS) Input
-	24	37	UIN	B-Y Input (Note 1)
-	25	38	VIN	R-Y Input (Note 1)
-	26	39	YIN	Y Input (Note 1)
-	27	40	YOUT	Y Output (Note 1)
-	28	41	VOUT	R-Y Output (Note 1)
-	29	42	UOUT	B-Y Output (Note 1)
30	30	43	BOUT	Blue Output
31	31	44	GOUT	Green Output
32	32	45	ROUT	Red Output
33	33	46	I _CATH	Cathode Current Measurement Input
34	34	47	BOSD	OSD Blue Input
35	35	48	GOSD	OSD Green Input
36	36	49	ROSD	OSD Red Input
37	37	50	FBOSD	OSD Fast Blanking
38	38	52	XTAL3/BTUN	3.5X MHz Crystal or Cloche Filter Tuning Capacitor
39	39	53	XTAL2	3.5X MHz Crystal
40	40	54	XTAL1	4.43/3.5X MHz Crystal
41	41	55	CLPF	Chroma PLL Filter
42	42	56	X1/VAMP/CHROUT	XTAL1 Control Pin, Vertical Amplitude DAC Output and Chroma Reference Signal Output.
43	43	57	GND1	Chroma/Scanning Ground

Page 25

STV223XD/3X/4X

Pin N°
STV224X/8X	STV223X	STV223XD	Symbol	Description
SDIP56	SDIP56	TQFP64
-	44	58	CVBSOUT1	Main Video Switch Output
45	45	59	V _CC 1	Chroma/Scanning Power Supply (8 V)
46	46	61	BCL/SAF	Beam Current Limiter Control Voltage and Safety Input (XRAY)
47	47	62	VERT	Vertical Output Pulse
48	48	63	HOUT	Horizontal Output Pulse
49	49	64	LFB/SSC	Line Flyback Input and Super-sandcastle Out- put
50	50	1	SLPF	Scanning PLL Filter
51	51	2	SCL	I ² C Bus Clock Input
52	52	3	SDA	I ² C Bus Data Input
53	53	4	V _CC D	Digital Supply Voltage (5 V)
54	54	5	GND D	Digital Ground
55	55	6	AUDIOOUT	Main Audio Output
56	56	7	FMCAP	FM Demodulation Capacitor
-	-	15	SAW	Filter Switch Control
25	-	30	BEXT/UEXT	External Blue Input or external U input
26	-	31	GEXT/YEXT	External Green Input or external Y input
27	-	32	REXT/VEXT	External Red Input or external V input
28	-	33	FBEXT	External Fast Blanking Input
24	-	36	APR	Automatic RGB Peak Regulation
-	-	51	HALFCTR	Half Contrast Input
44	-	60	CVBSOUT2	Second Video Switch Output

Note: 1. Input/Output not available in STV2236 and STV2236D versions.

Page 26

PIN CONNECTIONS STV223XD (TOEP64)

5/72

Page 27

STV223XD/3X/4X

BLOCK DIAGRAM (STV2238D) (TQFP64)

Page 28

Page 29

Page 30

Page 31

Page 32

Page 33

ELECTRICAL PARTS LIST

" A " is a safety part, so it must be used the same part.

LOC	PART CODE	PART NAME	DESCRIPTION	C807	CMYU3C222J	C MYLAR	1.6KV BCP 2200PF J
ZZ100	48B3740A01	TRANSMITTER REMOCON	R-40A01	C809	CH1HFE102M	C CERA AC	4.0KV 1000PF E DG
ZZ110	PTACPWA627	ACCESSORY AS	DTP-14C5TF	C812	CH1HFE102M	C CERA AC	4.0KV 1000PF E DG
00100	4850Q00910	BATTERY	R03/NN	C814	CCYR3A471K	C CERA	1KV R 470PF K 125 DE0705
M821	4858213800	BAG INSTRUCTION	L.D.P.E T0.05X250X400		DDG3	DIODE	DG3
ZZ120	PTBCSHD318	COVER BACK AS	DTP-21V4TF	D706	DLH2PR	LED BLOCK	LH-2P-R
M211	4852151601	COVER BACK	HIPS BK	D806	DRGP30J	DIODE	RGP30J
M541	4855415800	SPEC PLATE	150ART P/E FILM (C/TV)		5FSCB4022R	FUSE CERA	SEMKO F4AH 4A 250V MF51
ZZ130	PTPKCPD342	PACKING AS	DTP-21C6TF	1301	PTA2SW7104	HEAT SINK ASS`Y	1TDA1771 + 7174301011
10	6520010100	STAPLE PIN	18M/M J D O	1301	1TDA1771	IC VERTICAL	TDA1771
20	6520010200	STAPLE PIN	#3417	1301A	4857027104	HEAT SINK	SPCC T1.0+SN
M801	485805063B	BOX CARTON	DW-3A	I301B	7174301011	SCREW TAPPTITE	TT2 RND 3X10 MFZN
M811	4858190700	PAD	EPS 21C6	1601	1TDA7267A-	IC AMP	TDA7267A
M821	4858211800	BAG P.E	L.D.P.E T0.03X1300X1000	1702	1AT24C16PC	IC	AT24C16-10PC
ZZ131	48519A5310	CRT GROUND NET	2101S-1015-1P	1703	1KA7805	IC REGULATOR	KA7805
∆x Z132	58G0000074	COIL DEGAUSSING	DC-2070	1704	1KRT30	IC PREAMP	KRT30
ZZ140	PTCACAD342	CABINET AS	DTP-21C6TF		4850M04710	MODULE POWER	DPM001T1A
	PTRTPWD215	CRT AS	PAL 21" ITC CRT AS	1805	PTA2SW6904	HEAT SINK ASS`Y	1STV8131 + 7174301011
∧ v01	58D0000086	COIL DY	ODY-L2144	1805	1STV8131	IC REGULATOR	STV8131
V02	48A96R004-	RUBBER WEDGE	HMR 28 SR (\|0X54)	1805A	4857026904	HEAT SINK	AL EX
V03	4850PM001-	MAGNET CP	NY-225 (MINI NECK)	1805B	7174301011	SCREW TAPPTITE	TT2 RND 3X10 MFZN
V04	2TC26019BE	TAPE CLOTH	19X30 BEIGE	1901	PTB3SW1100	HEAT SINK ASS`Y	1TDA6103Q- + 7174301011
V05	2224050026	BOND SILICON	RTV 122 CARTRIDGE	1901	1TDA6103Q-	IC VIDEO	TDA6103Q
V06	2233030001	PAINT LOCK	3B-1401B	1901A	4857031100	HEAT SINK	A1050P-H24 T2.0
V901	48A96321P1	CRT BARE	A51JSW90X	I901B	7174301011	SCREW TAPPTITE	TT2 RND 3X10 MFZN
M191	4851934102	BUTTON CTRL	4943202+5538001	JS02	4859109950	JACK PIN BOARD	PH-JB-9710A
M191A	7178301212	SCREW TAPPTITE	TT2 WAS 3X12 MFZN BK	L101	58N0000044	COIL VCO	TRF-V010
M201A	4856013301	SCREW CRT FIXING	30X140 YL	L402	58H0000052	COIL H-LINEARITY	TRL-541B
M201B	4856214902	WASHER RUBBER	CR T2.0	L801	5PLF24A3	FILTER LINE	LF-24A3
M201C	4856013303	SCREW CRT FIXING	30X250 YL	L805	58C4500079	COIL CHOKE	L-45
M211A	7172401412	SCREW TAPPTITE	TT2 TRS 4X14 MFZN BK	M681	4856812001	TIE CABLE	NYLON66 DA100
M211B	7172401412	SCREW TAPPTITE	TT2 TRS 4X14 MFZN BK	M721	4857235402	SHIELD CASE	SPTH-C T0.25
M491	4854943203	BUTTON POWER	ABS BK	P401	4859240120	CONN WAFER	YFW500-06
M561	4855621401	MARK BRAND	ABS BK	P801	4859287320	CONN WAFER	MKS2822-6-10-202
M681	4856812001	TIE CABLE	NYLON66 DA100	P802	4859242220	CONN WAFER	YFW800-02
SP01A	7178301212	SCREW TAPPTITE	TT2 WAS 3X12 MFZN BK	P901	4850709N02	CONNECTOR	YBNH250-09YBNT025+ULW=300
ZZ200	PTFMSJD342	MASK FRONT AS	DTP-21C6TF	A801	4859906210	CORD POWER AS	6-L0+H03VVH2=2200
M201	4852071401	MASK FRONT	HIPS BK	A Q402	T2SD2499	TR	2SD2499
ZZ210	PTSPPWA627	SPEAKER AS	DTP-14C5TF	Q801	PTR2SW4500	HEAT SINK ASS`Y	T2SK2671 + 7174300811
P601A	4850703S50	CONNECTOR	YH025-03+35098+ULW=200		T2SK2671	FET	2SK2671
SP01	4858314010	SPEAKER	SP-5070F01 3W 8 OHM	Q801A	4857024500	HEAT SINK	AL EX B/K
ZZ290	PTMPMSD318	PCB MAIN MANUAL AS	DTP-21V4TF	Q801B	7174300811	SCREW TAPPTITE	TT2 RND 3X8 MFZN
C401	CMYE2D184J	C MYLAR	200V PU 0.18MF J	R801	DEC140M290	POSISTOR	ECPCC140M290
C404	CMYH3C622H	C MYLAR	1.6KV BUP 6200PF H	R802	RX07C339JF	R CEMENT	7W 3.3 OHM J 15MM 4P
C411	CMYN1J105K	C MYLAR (MKT)	63V 1MF K (7.5MM)	RLY1	5SC0101338	SW RELAY	DQ5D1-O(M)/GJ-SS-105LM
	CL1JB3474K	C LINE ACROSS	AC250V 0.47MF U/C/SNDF/SV	SCT1	4859303430	SOCKET CRT	PCS633A
∧ C805	CEYN2G181P	C ELECTRO	400V LHS 180MF (25X35)	SF101	5PG3962M	FILTER SAW	G 3962-M

Page 34

SF102	5PK9650M	FILTER SAW	K9650M	CC709	HCQK220JCA	C CHIP CERA	50V CH 22PF J 2012
SJ01	4859200401	SOCKET RGB	YRS21-R1	CC713	HCBK222KCA	C CHIP CERA	50V X7R 2200PF K 2012
AW801	5S40101146	SW POWER PUSH	SS-160-7-B	CC722	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012
T401	50D10A3	TRANS DRIVE	TD-10A3	CC723	HCQK220JCA	C CHIP CERA	50V CH 22PF J 2012
1	50H0000202	FBT	FUY20C001	CC801	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012
1	50M4042A5-	TRANS SMPS	TSM-4042A5	CC830	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012
	4859719930	TUNER VARACTOR	DT5-BF18D	1501	1STV2238DQ	IC CHIP VIDEO	STV2238D
W101	4851900130	GROUND TUNER AS	DS-W1015-S	1701	1ST195EPMQ	IC CHIP MICOM OTP	ST92T195Q1/EPM
ZZ200	PTMPJ2D318	PCB CHIP MOUNT B AS	DTP-21V4TF	JC001	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC102	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC002	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC103	HCQK101JCA	C CHIP CERA	50V CH 100PF J 2012	JC003	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC104	HCQK101JCA	C CHIP CERA	50V CH 100PF J 2012	JC004	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC105	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012	JC005	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC108	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC006	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC109	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC008	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC118	HCBK104KCA	C CHIP CERA	50V X7R 0.1MF K 2012	JC009	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC412	HCQK160JCA	C CHIP CERA	50V CH 16PF J 2012	JC011	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC501	HCQK101JCA	C CHIP CERA	50V CH 100PF J 2012	JC012	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC502	HCFK103ZCA	C CHIP CERA	50V Y5V 0.01MF Z 2012	JC013	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC504	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC014	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC505	HCBK472KCA	C CHIP CERA	50V X7R 4700PF K 2012	JC015	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC506	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012	JC016	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC508	HCBK472KCA	C CHIP CERA	50V X7R 4700PF K 2012	JC017	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC509	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC018	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC510	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC019	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC511	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC020	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC512	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC022	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC515	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC024	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC516	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	JC025	HRFT000-CA	R CHIP	1/10 0 OHM 2012
CC517	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	RC106	HRFT682JCA	R CHIP	1/10 6.8K OHM J 2012
CC518	HCBK222KCA	C CHIP CERA	50V X7R 2200PF K 2012	RC107	HRFT473JCA	R CHIP	1/10 47K OHM J 2012
CC519	HCFK334ZCA		50V Y5V 0.33MF Z 2012	RC111	HREI511JCA		1/10 510 OHM J 2012
CC520	HCFK104ZCA		50V Y5V 0.1MF Z 2012	RC114	HRF1432JCA		1/10 4.3K OHM J 2012
00500			50V X/R 4/00PF K 2012	RC115	HRF1102JCA		1/10 1K OHM J 2012
00500			50V CH 1000PF J 2012	RC301	HRFISOIJCA		1/10 560 OHM J 2012
00523			50V CH 1000PF J 2012	RC302			1/10 2.2K OHM J 2012
CC526			50V X7P 0 022ME K 2012	RC303			1/10 3.3K OHM J 2012
CC533			50V X5V 0 1ME 7 2012	BC306	HBET472.ICA	B CHIP	1/10 4 7K OHM J 2012
CC534			50V CH 30PE J 2012	BC307	HBET562JCA	B CHIP	1/10 5 6K OHM J 2012
CC535	HCOK300JCA		50V CH 30PE J 2012	BC308	HRFT332JCA	R CHIP	1/10 3.3K OHM J 2012
CC536	HCOK300JCA		50V CH 30PE J 2012	BC309	HRET154JCA	R CHIP	1/10 150K OHM J 2012
CC602	HCQK102JCA		50V CH 1000PF J 2012	RC310	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
CC603	HCQK102JCA		50V CH 1000PF J 2012	RC313	HRFT224JCA	R CHIP	1/10 220K OHM J 2012
CC604	HCQK102JCA	C CHIP CERA	50V CH 1000PF J 2012	RC404	HRFT561JCA	R CHIP	1/10 560 OHM J 2012
CC605	HCQK471JCA	C CHIP CERA	50V CH 470PF J 2012	RC405	HRFT562JCA	R CHIP	1/10 5.6K OHM J 2012
CC606	HCQK471JCA	C CHIP CERA	50V CH 470PF J 2012	RC406	HRFT562JCA	R CHIP	1/10 5.6K OHM J 2012
CC610	HCQK181JCA	C CHIP CERA	50V CH 180PF J 2012	RC408	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
CC612	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	RC419	HRFT152JCA	R CHIP	1/10 1.5K OHM J 2012
CC613	HCFK103ZCA	C CHIP CERA	50V Y5V 0.01MF Z 2012	RC420	HRFT394JCA	R CHIP	1/10 390K OHM J 2012
CC701	HCFK104ZCA	C CHIP CERA	50V Y5V 0.1MF Z 2012	RC501	HRFT750JCA	R CHIP	1/10 75 OHM J 2012
CC702	HCQK820JCA	C CHIP CERA	50V CH 82PF J 2012	RC503	HRFT750JCA	R CHIP	1/10 75 OHM J 2012
CC705	HCBK472KCA	C CHIP CERA	50V X7R 4700PF K 2012	RC504	HRFT750JCA	R CHIP	1/10 75 OHM J 2012
CC707	HCQK820JCA	C CHIP CERA	50V CH 82PF J 2012	RC505	HRFT750JCA	R CHIP	1/10 75 OHM J 2012
CC708	HCBK472KCA	C CHIP CERA	50V X7R 4700PF K 2012	RC506	HRFT101JCA	R CHIP	1/10 100 OHM J 2012

Page 35

RC507	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC712	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
RC508	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC713	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
RC509	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	RC714	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
RC510	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	RC715	HRFT152JCA	R CHIP	1/10 1.5K OHM J 2012
RC511	HRFT470JCA	R CHIP	1/10 47 OHM J 2012	RC716	HRFT392JCA	R CHIP	1/10 3.9K OHM J 2012
RC512	HRFT223JCA	R CHIP	1/10 22K OHM J 2012	RC717	HRFT153JCA	R CHIP	1/10 15K OHM J 2012
RC513	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC719	HRFT332JCA	R CHIP	1/10 3.3K OHM J 2012
RC514	HRFT151JCA	R CHIP	1/10 150 OHM J 2012	RC720	HRFT271JCA	R CHIP	1/10 270 OHM J 2012
RC515	HRFT000-CA	R CHIP	1/10 0 OHM 2012	RC721	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
RC516	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	RC722	HRFT332JCA	R CHIP	1/10 3.3K OHM J 2012
RC517	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	RC723	HRFT624JCA	R CHIP	1/10 620K OHM J 2012
RC518	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	RC725	HRFT471JCA	R CHIP	1/10 470 OHM J 2012
RC519	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	RC726	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
RC520	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC727	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
RC521	HRFT363JCA	R CHIP	1/10 36K OHM J 2012	RC729	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
RC522	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	RC730	HRFT332JCA	R CHIP	1/10 3.3K OHM J 2012
RC523	HRFT822JCA	R CHIP	1/10 8.2K OHM J 2012	RC731	HRFT100JCA	R CHIP	1/10 10 OHM J 2012
RC524	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC732	HRFT000-CA	R CHIP	1/10 0 OHM 2012
RC525	HRFT153JCA	R CHIP	1/10 15K OHM J 2012	RC733	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
RC526	HRFT273JCA	R CHIP	1/10 27K OHM J 2012	RC736	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
RC527	HRFT473JCA	R CHIP	1/10 47K OHM J 2012	RC738	HRFT101JCA	R CHIP	1/10 100 OHM J 2012
RC528	HRFT221JCA	R CHIP	1/10 220 OHM J 2012	RC751	HRFT103JCA	R CHIP	1/10 10K OHM J 2012
RC529	HRFT271JCA	R CHIP	1/10 270 OHM J 2012	RC752	HRFT682JCA	R CHIP	1/10 6.8K OHM J 2012
RC530	HRFT271JCA	R CHIP	1/10 270 OHM J 2012	RC754	HRFT333JCA	R CHIP	1/10 33K OHM J 2012
RC531	HRFT271JCA	R CHIP	1/10 270 OHM J 2012	RC755	HRFT473JCA	R CHIP	1/10 47K OHM J 2012
RC532	HRFT333JCA	R CHIP	1/10 33K OHM J 2012	RC822	HRFT273JCA	R CHIP	1/10 27K OHM J 2012
RC534	HRFT334JCA	R CHIP	1/10 330K OHM J 2012	RC828	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
RC535	HRFT184JCA	R CHIP	1/10 180K OHM J 2012	RC829	HRFT102JCA	R CHIP	1/10 1K OHM J 2012
RC537	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	RC901	HRFT272JCA	R CHIP	1/10 2.7K OHM J 2012
RC538	HRFT223JCA	R CHIP	1/10 22K OHM J 2012	RC902	HRFT302JCA	R CHIP	1/10 3K OHM J 2012
RC539	HRFT122JCA	R CHIP	1/10 1.2K OHM J 2012	RC903	HRFT302JCA	R CHIP	1/10 3K OHM J 2012
RC541	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	RC904	HRFT302JCA	R CHIP	1/10 3K OHM J 2012
RC542	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	RC905	HRFT272JCA	R CHIP	1/10 2.7K OHM J 2012
RC543	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	RC906	HRFT272JCA	R CHIP	1/10 2.7K OHM J 2012
RC553	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	RC907	HRFT272JCA	R CHIP	1/10 2.7K OHM J 2012
RC555	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	ZZ200	PTMPJ0D318	PCB MAIN (RHU) AS	DTP-21V4TF
RC560	HRFT472JCA	R CHIP	1/10 4.7K OHM J 2012	C103	CEXF1C222V	C ELECTRO	16V RSS 2200MF (13X25) TP
RC605	HRFT153JCA	R CHIP	1/10 15K OHM J 2012	C301	CEXF1V471C	C ELECTRO	35V RUS 470MF (10X20) TP
RC606	HRFT153JCA	R CHIP	1/10 15K OHM J 2012	C302	CCXB3A471K	C CERA	1KV B 470PF K (T)
RC610	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	C303	CEXF1E102V	C ELECTRO	25V RSS 1000MF (13X20) TP
RC611	HRFT152JCA	R CHIP	1/10 1.5K OHM J 2012	C305	CMXE2A473J	C MYLAR	100V PU 0.047MF J
RC620	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	C405	CCXB3D271K	C CERA	2KV B 270PF K (T)
RC621	HRFT104JCA	R CHIP	1/10 100K OHM J 2012	C421	CEXF2E330V	C ELECTRO	250V RSS 33MF (13X25) TP
RC623	HRFT103JCA	R CHIP	1/10 10K OHM J 2012	C606	CEXF1C471V	C ELECTRO	16V RSS 470MF (10X12.5)TP
RC630	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	C704	CEXF1C102V	C ELECTRO	16V RSS 1000MF (10X20) TP
RC702	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	C815	CEXF2C101V	C ELECTRO	160V RSS 100MF (16X25) TP
RC703	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	C818	CEXF2C101V	C ELECTRO	160V RSS 100MF (16X25) TP
RC704	HRFT562JCA	R CHIP	1/10 5.6K OHM J 2012	C820	CEXF1E102V	C ELECTRO	25V RSS 1000MF (13X20) TP
RC705	HRFT153JCA	R CHIP	1/10 15K OHM J 2012	C827	CEXF1C222V	C ELECTRO	16V RSS 2200MF (13X25) TP
RC706	HRFT562JCA	R CHIP	1/10 5.6K OHM J 2012	C830	CEXF1C471V	C ELECTRO	16V RSS 470MF (10X12.5)TP
RC707	HRFT101JCA	R CHIP	1/10 100 OHM J 2012	C906	CBXB3D102K	C CERA SEMI	2KV BL(N) 1000PF K (T)
RC708	HRFT102JCA	R CHIP	1/10 1K OHM J 2012	/! \ L800	58Q0000093	COIL DELAY LINE	RS208
RC709	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	ZZ200	PTMPJBD318	PCB MAIN M-10 AS	DTP-21V4TF
RC710	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	10	2TM18006BE	TAPE MASKING	6.2X500
RC711	HRFT222JCA	R CHIP	1/10 2.2K OHM J 2012	P101	485923162S	CONN WAFER	YW025-03 (STICK)

Page 36

P601	485923162S	CONN WAFER	YW025-03 (STICK)	C905	CMXL2E104K	C MYLAR	250V MEU 0.1MF K
R402	RS02Z103JS	R M-OXIDE FILM	2W 10K OHM J SMALL	F801A	4857415001	CLIP FUSE	PFC5000-0702
R403	RS01Z479J-	R M-OXIDE FILM	1W 4.7 OHM J (TAPPING)	F801B	4857415001	CLIP FUSE	PFC5000-0702
R808	RS02Z828JS	R M-OXIDE FILM	2W 0.82 OHM J SMALL	Q105	TKTC3198Y-	TR	KTC3198Y
R819	RS02Z278JS	R M-OXIDE FILM	2W 0.27 OHM J SMALL	Q401	TKTC3207	TR	KTC3207 (TP)
ZZ200	PTMPJRD318	PCB MAIN RADIAL AS	DTP-21V4TF	Q501	TKTC3198Y-	TR	KTC3198Y
C101	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	Q502	TKTC3198Y-	TR	KTC3198Y
C102	CEXF1H479V	C ELECTRO	50V RSS 4.7MF (5X11) TP	Q503	TKTA1266Y-	TR	KTA1266Y (TP)
C304	CEXF1H100V	C ELECTRO	50V RSS 10MF (5X11) TP	Q505	TKTA1266Y-	TR	KTA1266Y (TP)
C306	CEXF1V101C	C ELECTRO	35V RUS 100MF (8X11.5) TP	Q506	TKTC3198Y-	TR	KTC3198Y
C307	CMXB1H224J	C MYLAR	50V EU 0.22MF J (TP)	Q601	TKTC3198Y-	TR	KTC3198Y
C313	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	Q620	TKTA1266Y-	TR	KTA1266Y (TP)
C402	CEXF2C109V	C ELECTRO	160V RSS 1MF (6.3X11) TP	Q701	TKTA1266Y-	TR	KTA1266Y (TP)
C406	CCXB2H102K	C CERA	500V B 1000PF K (TAPPING)	Q702	TKTC3198Y-	TR	KTC3198Y
C410	CMXM2A104J	C MYLAR	100V 0.1MF J (TP)	Q703	TKTC3198Y-	TR	KTC3198Y
C420	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	Q704	TKTC3198Y-	TR	KTC3198Y
C501	CEXF1H478V	C ELECTRO	50V RSS 0.47MF (5X11) TP	Q705	TKTC3198Y-	TR	KTC3198Y
C502	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	Q710	TKTC3198Y-	TR	KTC3198Y
C503	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	Q802	TKSA1013Y-	TR	KSA1013Y (TP)
C504	CEXD1H229F	C ELECTRO	50V RND 2.2MF (5X11) TP	R302	RN02B229JS	R METAL FILM	2W 2.2 OHM J SMALL
C506	CEXD1H229F	C ELECTRO	50V RND 2.2MF (5X11) TP	R303	RN02B271JS	R METAL FILM	2W 270 OHM J SMALL
C507	CEXF1C101V	C ELECTRO	16V RSS 100MF (6.3X11) TP	R307	RN02B910JS	R METAL FILM	2W 91 OHM J SMALL
C511	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	R308	RN02B910JS	R METAL FILM	2W 91 OHM J SMALL
C512	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	R309	RN02B910JS	R METAL FILM	2W 91 OHM J SMALL
C513	CEXF1H100V	C ELECTRO	50V RSS 10MF (5X11) TP	R310	RN02B910JS	R METAL FILM	2W 91 OHM J SMALL
C514	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	/ R401	RN02B332JS	R METAL FILM	2W 3.3K OHM J SMALL
C515	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	/ R404	RN02B332JS	R METAL FILM	2W 3.3K OHM J SMALL
C516	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	R410	RN01B132JS	R METAL FILM	1W 1.3K OHM J SMALL
C517	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	R503	RN01B300JS	R METAL FILM	1W 30 OHM J SMALL
C520	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	R850	RN02B180JS	R METAL FILM	2W 18 OHM J SMALL
C522	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	R901	RN01B124JS	R METAL FILM	1W 120K OHM J SMALL
C523	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	R902	RN01B124JS	R METAL FILM	1W 120K OHM J SMALL
C524	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	R903	RN01B124JS	R METAL FILM	1W 120K OHM J SMALL
C601	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	SW701	5S50101090	SW TACT	SKHV17910A
C602	CEXF1H108V	C ELECTRO	50V RSS 0.1MF (5X11) TP	SW702	5S50101090	SW TACT	SKHV17910A
C611	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	SW703	5$50101090	SW TACT	SKHV17910A
C620	CEXF1H100V	C ELECTRO	50V RSS 10MF (5X11) TP	SW704	5S50101090	SW TACT	SKHV17910A
C702	CEXF1H109V	C ELECTRO	50V RSS 1MF (5X11) TP	SW705	5$50101090	SW TACT	SKHV17910A
C703	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	X501	5XEX4R433B	CRYSTAL QUARTZ	HC-49U 4.43361M 15PPM TP
C706	CEXF1H478V	C ELECTRO	50V RSS 0.47MF (5X11) TP	X502	5XEX3R579B	CRYSTAL QUARTZ	HC-49U 3.57954M 15PPM TP
C803	CCXF3A472Z	C CERA	1KV F 4700PF Z (T)	X701	5XEX4R000C	CRYSTAL QUARTZ	HC-49U 4.0000MHZ (TP)
C804	CCXF3A472Z	C CERA	1KV F 4700PF Z (T)	ZZ200	PTMPJAD318	PCB MAIN AXIAL AS	DTP-21V4TF
C816	CCXB3A471K	C CERA	1KV B 470PF K (T)	10	2TM14006LB	TAPE MASKING	3M #232 6.0X2000M
C819	CEXF2A100C	C ELECTRO	RUS 100V 10MF 5*11	20	2TM10006LB	TAPE MASKING	3M #232-MAP-C 6.2X2000M
C822	CEXF1C101V	C ELECTRO	16V RSS 100MF (6.3X11) TP	A001	4859803593	PCB MAIN	246X246 D1B
C823	CCXB3A471K	C CERA	1KV B 470PF K (T)	D101	D1N4148	DIODE	1N4148 (TAPPING)
C824	CCXB3A471K	C CERA	1KV B 470PF K (T)	D103	D1SS85TA	DIODE	1SS85TA
C825	CEXF1H220V	C ELECTRO	50V RSS 22MF (5X11) TP	D105	DUZ33B	DIODE ZENER	UZ-33B
C826	CEXF1H479V	C ELECTRO	50V RSS 4.7MF (5X11) TP	D106	D1N4148	DIODE	1N4148 (TAPPING)
C828	CEXF1C101V	C ELECTRO	16V RSS 100MF (6.3X11) TP	D107	DUZ5R1B	DIODE ZENER	UZ-5.1B UNIZON
C829	CEXF1H100V	C ELECTRO	50V RSS 10MF (5X11) TP	D301	NBYD33GT	DIODE	BYD33G-T
C841	CCXF1H103Z	C CERA	50V F 0.01MF Z (TAPPING)	D303	NBYD33GT	DIODE	BYD33G-T
C842	CCXB3A102K	C CERA	1KV B 1000PF K (TAPPING)	D402	NBYD33GT	DIODE	BYD33G-T
C850	CEXF1C470V	C ELECTRO	16V RSS 47MF (5X11) TP	D403	NBYD33GT	DIODE	BYD33G-T
C902	CMXL2E104K	C MYLAR	250V MEU 0.1MF K	D410	DUZ5R1B	DIODE ZENER	UZ-5.1B UNIZON

Page 37

D450	D1N4148	DIODE	1N4148 (TAPPING)	J02	8 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D452	D1N4148	DIODE	1N4148 (TAPPING)	J02	9 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D501	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J03	0 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D502	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J03	1 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D503	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J03	2 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D504	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J03	4 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D505	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J03	5 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D506	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J03	6 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D507	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J03	7 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D508	D1N4148	DIODE	1N4148 (TAPPING)	J03	8 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D509	D1N4148	DIODE	1N4148 (TAPPING)	J03	9 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D510	DUZ5R1B	DIODE ZENER	UZ-5.1B UNIZON	J04	2 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D512	D1N4148	DIODE	1N4148 (TAPPING)	J04	3 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D513	D1N4148	DIODE	1N4148 (TAPPING)	J04	4 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D514	D1N4148	DIODE	1N4148 (TAPPING)	J04	5 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D601	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J04	6 RD-4Z101J-	R CARBON FILM	1/4 100 OHM J
D602	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J04	7 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D603	DUZ5R6BM	DIODE ZENER	UZ-5.6BM(TAPPING)	J04	8 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D610	D1N4148	DIODE	1N4148 (TAPPING)	J05	0 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D620	D1N4148	DIODE	1N4148 (TAPPING)	J05	1 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D701	DUZ3R9B	DIODE ZENER	UZ-3.9B	J05	2 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D704	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	J05	3 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D720	D1N4148	DIODE	1N4148 (TAPPING)	J05	4 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D808	D1N4936GP-	DIODE	1N4936GP (TAPPING)	J05	5 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D810	D1N4936GP-	DIODE	1N4936GP (TAPPING)	J05	7 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D812	D1N4936GP-	DIODE	1N4936GP (TAPPING)	J05	8 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D816	DMTZJ10B	DIODE ZENER	MTZJ 10B (TAPPING)	J05	9 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D820	D1N4148	DIODE	1N4148 (TAPPING)	J06	0 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D835	DR2M	DIODE ZENER	R2M	J06	1 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D837	DLT2A05G	DIODE	LT2A05G (TP)	J06	4 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D838	DLT2A05G	DIODE	LT2A05G (TP)	J06	5 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D839	DLT2A05G	DIODE	LT2A05G (TP)	J06	6 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
D840	DLT2A05G	DIODE	LT2A05G (TP)	J06	7 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J003	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	J06	8 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J005	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	J06	9 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J006	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	J07	0 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J007	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	J07	1 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J009	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	J07	2 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J010	85801065GY		AWG22 1/0.65 TIN COATING	J07	3 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J011	85801065GY			J07	4 85801065GY
J012	85801065G1			J07	5 85801065GY
1014	00001000G1			107	7 959010650V
1015	00001000G1			107	05001005G1
1016	85801065GV			107	85801065GV
1017	85801065GV			108	9 85801065GV
1018	85801065GY			108	1 85801065GY
1010	8580106507			100	2 8580106507		AWG22 1/0.65 TIN COATING
1020	8580106507			100	4 8580106507		AWG22 1/0.05 TIN COATING
1020	8580106507			100	5 85801065GV		AWG22 1/0.65 TIN COATING
.1022	85801065GV		AWG22 1/0.65 TIN COATING	.108	6 85801065GV		AWG22 1/0 65 TIN COATING
.1023	85801065GY		AWG22 1/0.65 TIN COATING	,108	7 85801065GY		AWG22 1/0.65 TIN COATING
.1024	85801065GY		AWG22 1/0.65 TIN COATING	,108	8 85801065GY		AWG22 1/0.65 TIN COATING
.1025	85801065GY		AWG22 1/0.65 TIN COATING	,108	9 85801065GY		AWG22 1/0.65 TIN COATING
J027	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	J09	0 85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING

Page 38

.\|091	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	R301	RD-27249.1-	B CABBON FILM	1/2 2.4 OHM J
.1092	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	R406	RD-27472.I-		1/2 4.7K OHM J
J093	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	R407	RD-4Z102J-	R CARBON FILM	1/4 1K OHM J
.1094	85801065GY		AWG22 1/0 65 TIN COATING	R408	BD-47102.I-		1/4 1K OHM J
.1095	85801065GY		AWG22 1/0 65 TIN COATING	R409	BD-47561.I-		1/4 560 OHM J
.1096	85801065GY		AWG22 1/0 65 TIN COATING	B501	RD-47101.I-		1/4 100 OHM J
.1097	85801065GY		AWG22 1/0 65 TIN COATING	R502	BD-47101.I-		1/4 100 OHM J
.1098	85801065GY			R512	BD-47750.1-		1/4 75 OHM J
.1099	85801065GY		AWG22 1/0.65 TIN COATING	R521	RD-47101.I-		1/4 100 OHM J
.1100	85801065GY		AWG22 1/0.65 TIN COATING	R525	RD-47104.I-		1/4 100K OHM J
.1104	85801065GY			R526	BD-471021-
.1105	85801065GY			R532	BD-47101.I-		1/4 100 OHM J
1108	85801065GY			R601	BD-271021-		1/2 1K OHM I
1100	85801065GY			B602	RD-47471 I-		1/2 11 OHM 1
1110	85801065GV			D611	PD-47362 L		1/4 3 6K OHM 1
1111	95901065CV			D715	D-4Z302J-
1110	95901065CV			D700	DD-47222
J112	858010650V		AWG22 1/0.03 TIN COATING	R/23	D-47100
5110	959010050V		AWG22 1/0.00 TIN COATING	H/35	D-47004
J114	05801065GY		AWG22 1/0.65 TIN COATING	R/36	KU-42224J-
J115	05801065GY		AWG22 1/0.65 TIN COATING	R/53	HU-424/3J-
J116	05801065GY		AWG22 1/0.65 TIN COATING	R803	HU-42514J-
J117	85801065GY			R804	RD-42514J-
J118	85801065GY			R805	85801065GY		AWG22 1/0.65 TIN COATING
J119	85801065GY		AWG22 1/0.65 TIN COATING	R806	RD-4Z363J-		1/4 36K OHM J
J120	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	R809	RD-4Z363J-		1/4 36K OHM J
J121	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	R810	RD-42333J-		1/4 33K OHM J
J122	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	R812	RC-22825KP		1/2 8.2M OHM K
J123	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING	R823	RD-42101J-		1/4 100 OHM J
J124	85801065GY			R824	RD-4Z101J-		1/4 100 OHM J
J125	8580106561			R834	RD-42392J-
J127	85801065GY			R890	RC-2Z335KP		1/2 3.3M OHM K
J128	85801065GY			R910	RD-22152J-		1/2 1.5K OHM J
J129	85801065GY			R911	RD-22152J-		1/2 1.5K OHM J
3130	00000000001	WIRE COPPER	AWG22 1/0.65 TIN COATING	R912	RD-22152J-	R CARBON FILM	1/2 1.5K UHM J
J133	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J134	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J135	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
J136	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
L301	5CPZ100K04		10UH 10.5MM K (LAL04TB)
L511	5CPZ100K02		10UH K (AXIAL 3.5MM)
L601	5CPZ109M02		1UH M (AXIAL 3.5MM)
L602	5CPZ109M02	CUIL PEAKING	1UH M (AXIAL 3.5MM)
L603	85801065GY	WIRE COPPER	AWG22 1/0.65 TIN COATING
L604	5CPZ109M02		1UH M (AXIAL 3.5MM)
L606	85801065GY		AWG22 1/0.65 TIN COATING
L701	5CPZ100K02		10UH K (AXIAL 3.5MM)
L702	5CPZ569K02	COIL PEAKING	5.6UH K (AXIAL 3.5MM)
L802	5MC0000100	COIL BEAD	HC-3550
L803	5MC0000100	COIL BEAD	HC-3550
L806	5CPZ390K04	COIL PEAKING	39UH 10.5MM K (LAL04TB)
R101	RD-4Z242J-	R CARBON FILM	1/4 2.4K OHM J
R109	RD-4Z183J-	R CARBON FILM	1/4 18K OHM J
R110	RD-4Z102J-	R CARBON FILM	1/4 1K OHM J
R111	RD-4Z101J-	R CARBON FILM	1/4 100 OHM J
D120	DD-47101 I-