DDU66C
Doc #97021 DATA DELAY DEVICES, INC. 1
2/5/97 3 Mt. Prospect Ave. Clifton, NJ 07013
5-TAP, HCMOS-INTERFACED
FIXED DELAY LINE
(SERIES DDU66C)
FEATURES PACKAGES
• Five equally spaced outputs
• Fits standard 14-pin DIP socket
• Low profile
• Auto-insertable
• Input & outputs fully CMOS interfaced & buffered
• 10 T2L fan-out capability
FUNCTIONAL DESCRIPTION
The DDU66C-series device is a 5-tap digitally buffered delay line. The
signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an
amount given by the device dash number. For dash numbers less than 40,
the total delay of the line is measured from T1 to T5, with the nominal value
given by the dash number. The nominal tap-to-tap delay increment is
given by 1/4 of this number. The inherent delay from IN to T1 is nominally 8.0ns. For dash numbers
greater than or equal to 40, the total delay of the line is measured from IN to T5, with the nominal value
given by the dash number. The nominal tap-to-tap delay increment is given by 1/5 of this number.
SERIES SPECIFICATIONS
• Minimum input pulse width: 40% of total delay
• Output rise time: 8ns typical
• Supply voltage: 5VDC ± 5%
• Supply current: I
CCL
= 40µa typical
I
CCH
= 10ma typical
• Operating temperature: 0° to 70° C
• Temp. coefficient of total delay: 300 PPM/°C
25% 25% 25% 25%
VCC GNDIN T1 T2 T3 T4 T5
Functional diagram for dash numbers < 40
8.0ns
20% 20% 20% 20% 20%
VCC GNDIN T1 T2 T3 T4 T5
Functional diagram for dash numbers >= 40
1997 Data Delay Devices
data
delay
devices,
inc.
3
14
12
10
8
1
4
6
7
IN
T2
T4
GND
VDD
T1
T3
T5
1
2
3
4
5
6
7
14
13
12
11
10
9
8
IN
N/C
N/C
T2
N/C
T4
GND
VDD
N/C
T1
N/C
T3
N/C
T5
DDU66C-xxD1 Com. SMD
DDU66C-xxD4 Com. SMD
DDU66C-xxMD1 Mil. SMD
DDU66C-xxMD4 Mil. SMD
DDU66C-xx DIP
DDU66C-xxA2 Gull-Wing
DDU66C-xxB2 J-Lead
DDU66C-xxME7Military DIP
PIN DESCRIPTIONS
IN Signal Input
T1-T5 Tap Outputs
VDD +5 Volts
GND Ground
DASH NUMBER SPECIFICATIONS
Part
Number
Total
Delay (ns)
Delay Per
Tap (ns)
DDU222C-10
10 ± 2.0 * 2.5 ± 1.0
DDU222C-20
20 ± 2.0 * 5.0 ± 2.0
DDU222C-50
50 ± 3.0 10.0 ± 3.0
DDU222C-60
60 ± 3.0 12.0 ± 3.0
DDU222C-75
75 ± 4.0 15.0 ± 3.0
DDU222C-100
100 ± 5.0 20.0 ± 3.0
DDU222C-125
125 ± 6.5 25.0 ± 3.0
DDU222C-150
150 ± 7.5 30.0 ± 3.0
DDU222C-175
175 ± 8.0 35.0 ± 4.0
DDU222C-200
200 ± 10.0 40.0 ± 4.0
DDU222C-250
250 ± 12.5 50.0 ± 5.0
* Total delay is referenced to first tap output
Input to first tap = 8.0ns ±± 2ns
NOTE: Any dash number between 10 and 250 not
shown is also available.
DDU66C
Doc #97021 DATA DELAY DEVICES, INC. 2
2/5/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
APPLICATION NOTES
HIGH FREQUENCY RESPONSE
The DDU66C tolerances are guaranteed for input
pulse widths and periods greater than those
specified in the test conditions. Although the
device will function properly for pulse widths as
small as 40% of the total delay and periods as
small as 80% of the total delay (for a symmetric
input), the delays may deviate from their values at
low frequency. However, for a given input
condition, the deviation will be repeatable from
pulse to pulse. Contact technical support at Data
Delay Devices if your application requires device
testing at a specific input condition.
POWER SUPPLY BYPASSING
The DDU66C relies on a stable power supply to
produce repeatable delays within the stated
tolerances. A 0.1uf capacitor from VDD to GND,
located as close as possible to the VDD pin, is
recommended. A wide VDD trace and a clean
ground plane should be used.
DEVICE SPECIFICATIONS
TABLE 1: ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL MIN MAX UNITS NOTES
DC Supply Voltage V
DD
-0.3 7.0 V
Input Pin Voltage V
IN
-0.3 VDD+0.3 V
Storage Temperature T
STRG
-55 150 C
Lead Temperature T
LEAD
300 C 10 sec
TABLE 2: DC ELECTRICAL CHARACTERISTICS
(0C to 70C, 4.75V to 5.25V)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
High Level Output Voltage V
OH
3.98 4.4 V VDD = 5.0, IOH = MAX
VIH = MIN, VIL = MAX
Low Level Output Voltage V
OL
0.15 0.26 V VDD = 5.0, IOL = MAX
VIH = MIN, VIL = MAX
High Level Output Current I
OH
-4.0 mA
Low Level Output Current I
OL
4.0 mA
High Level Input Voltage V
IH
3.15 V
Low Level Input Voltage V
IL
1.35 V
Input Current I
IH
0.10
µA
VDD = 5.0
DDU66C
Doc #97021 DATA DELAY DEVICES, INC. 3
2/5/97 3 Mt. Prospect Ave. Clifton, NJ 07013
PACKAGE DIMENSIONS
DDU66C-xx (Commercial)
.780 MAX.
1 4 6 7
814 12 10
.290
MAX.
.015 TYP.
.070 MAX.
.018
TYP.
.600±.010
.280
MAX.
.350
MAX.
.010±.002
Lead Material:
Nickel-Iron alloy 42
TIN PLATE
DDU66C-xxME7 (Military)
.130
±
.030
.820 MAX.
1 4 6 7
814 12 10
.320
MAX.
.018 TYP.
.410
TYP.
.300
TYP.
.020 TYP.
.600 TYP.
.020
TYP.
.100
TYP.
.790 MAX.
.430
TYP.
.020 TYP. .040
TYP.
.100.090
.600
.300
MAX.
.270
TYP.
.010 TYP.
.050
TYP.
1 4 6 7
8101214
DDU66C-xxA2 (Commercial Gull-Wing)
.790 MAX.
1 4 6 7
8
.320
TYP.
.020 TYP.
.040
TYP.
.100.110
.600
.350
MAX.
.270
TYP.
.050 TYP.
.110
TYP.
101214
DDU66C-xxB2 (Commercial J-Lead)
.008
.510 MAX.
1
7 8
.510
MAX.
.045
14
.300
TYP.
.017
.050
.100
.100
.025
.300.300
.360
TYP.
.065
TYP.
.065
TYP.
.200 MAX. (Com)
.225 MAX. (Mil)
DDU66C-xxD1 (Commercial SMD)
DDU66C-xxMD1 (Military SMD)
.200 MAX. (Com)
.225 MAX. (Mil)
.080 .080
.510 MAX.
1
7 8
14
.510
MAX.
.017
.050
.300
TYP.
.100
.100
.650
.008
.005
.065 TYP.
.360 TYP.
.065 TYP.
DDU66C-xxD4 (Commercial SMD)
DDU66C-xxMD4 (Military SMD)
DDU66C
Doc #97021 DATA DELAY DEVICES, INC. 4
2/5/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
DELAY LINE AUTOMATED TESTING
TEST CONDITIONS
INPUT: OUTPUT:
Ambient Temperature: 25oC ± 3oC Load: 1 FAST-TTL Gate
Supply Voltage (VDD): 5.0V ± 0.1V C
load
: 5pf ± 10%
Input Pulse: High = 5.0V ± 0.1V Threshold: 2.5V (Rising & Falling)
Low = 0.0V ± 0.1V
Source Impedance: 50Ω Max.
Rise/Fall Time: 5.0 ns Max. (measured
between 0.5V and 4.5V )
Pulse Width: PWIN = 1.5 x Total Delay
Period: PERIN = 10 x Total Delay
NOTE: The above conditions are for test only and do not in any way restrict the operation of the device.
T1OUT
TRIG
IN
REF
TRIG
Test Setup
DEVICE UNDER
TEST (DUT)
TIME INTERVAL
COUNTER
PULSE
GENERATOR
COMPUTER
SYSTEM
PRINTER
IN
T2
T3
T4
T5
0.5V0.5V
Timing Diagram For Testing
T
RISE
T
FALL
PER
IN
PW
IN
T
RISE
T
FALL
2.5V2.5V
4.5V 4.5V
2.5V2.5V
V
IH
V
IL
V
OH
V
OL
INPUT
SIGNAL
OUTPUT
SIGNAL
Loading...