DADD DDU4F-5400A2, DDU4F-5400, DDU4F-5300MC2, DDU4F-5300M, DDU4F-5300B2 Datasheet
...
DDU4F
Doc #97033 DATA DELAY DEVICES, INC. 1
12/10/97 3 Mt. Prospect Ave. Clifton, NJ 07013
5-TAP, TTL-INTERFACED
FIXED DELAY LINE
(SERIES DDU4F)
FEATURES PACKAGES
• Five equally spaced outputs
• Fits standard 14-pin DIP socket
• Low profile
• Auto-insertable
• Input & outputs fully TTL interfaced & buffered
• 10 T2L fan-out capability
FUNCTIONAL DESCRIPTION
The DDU4F-series device is a 5-tap digitally buffered delay line. The
signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an
amount determined by the device dash number (See Table). For dash
numbers less than 5025, the total delay of the line is measured from T1 to
T5. The nominal tap-to-tap delay increment is given by one-fourth of the
total delay, and the inherent delay from IN to T1 is nominally 3.5ns. For
dash numbers greater than or equal to 5025, the total delay of the line is measured from IN to T5. The
nominal tap-to-tap delay increment is given by one-fifth of this number.
SERIES SPECIFICATIONS
• Minimum input pulse width: 20% of total delay
• Output rise time: 2ns typical
• Supply voltage: 5VDC ± 5%
• Supply current: I
CCL
= 32ma typical
I
CCH
= 7ma typical
• Operating temperature: 0° to 70° C
• Temp. coefficient of total delay: 100 PPM/°C
25% 25% 25% 25%
VCC GNDIN T1 T2 T3 T4 T5
Functional diagram for dash numbers < 5025
3.5ns
20% 20% 20% 20% 20%
VCC GNDIN T1 T2 T3 T4 T5
Functional diagram for dash numbers >= 5025
1997 Data Delay Devices
data
delay
devices,
inc.
3
1
2
3
4
5
6
7
14
13
12
11
10
9
8
IN
N/C
N/C
T2
N/C
T4
GND
VDD
N/C
T1
N/C
T3
N/C
T5
14
12
10
8
1
4
6
7
IN
T2
T4
GND
VCC
T1
T3
T5
DDU4F-xx DIP
DDU4F-xxA2 Gull-Wing
DDU4F-xxB2 J-Lead
DDU4F-xxM Military DIP
Military SMD
DDU4F-xxMC2
PIN DESCRIPTIONS
IN Signal Input
T1-T5 Tap Outputs
VCC +5 Volts
GND Ground
DASH NUMBER SPECIFICATIONS
Part
Number
Total
Delay (ns)
Delay Per
Tap (ns)
DDU4F-5004
4 ± 1.0 * 1.0 ± 0.5
DDU4F-5006
6 ± 1.0 * 1.5 ± 0.5
DDU4F-5008
8 ± 2.0 * 2.0 ± 1.0
DDU4F-5010
10 ± 2.0 * 2.5 ± 1.0
DDU4F-5012
12 ± 2.0 * 3.0 ± 1.0
DDU4F-5016
16 ± 2.0 * 4.0 ± 1.5
DDU4F-5020
20 ± 3.0 * 5.0 ± 2.0
DDU4F-5025
25 ± 3.0 5.0 ± 2.0
DDU4F-5030
30 ± 3.0 6.0 ± 2.0
DDU4F-5040
40 ± 3.0 8.0 ± 2.0
DDU4F-5050
50 ± 3.0 10.0 ± 3.0
DDU4F-5060
60 ± 3.0 12.0 ± 3.0
DDU4F-5075
75 ± 4.0 15.0 ± 3.0
DDU4F-5100
100 ± 5.0 20.0 ± 3.0
DDU4F-5125
125 ± 6.5 25.0 ± 3.0
DDU4F-5150
150 ± 7.5 30.0 ± 3.0
DDU4F-5200
200 ± 10.0 40.0 ± 4.0
DDU4F-5250
250 ± 12.5 50.0 ± 5.0
DDU4F-5300
300 ± 15.0 60.0 ± 6.0
DDU4F-5400
400 ± 20.0 80.0 ± 8.0
DDU4F-5500
500 ± 25.0 100.0 ± 10.0
* Total delay is referenced to first tap output
Input to first tap = 3.5ns ±± 1ns
NOTE: Any dash number between 5004 and 5500
DDU4F
Doc #97033 DATA DELAY DEVICES, INC. 2
12/10/97 Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
APPLICATION NOTES
HIGH FREQUENCY RESPONSE
The DDU4F tolerances are guaranteed for input
pulse widths and periods greater than those
specified in the test conditions. Although the
device will function properly for pulse widths as
small as 20% of the total delay and periods as
small as 40% of the total delay (for a symmetric
input), the delays may deviate from their values at
low frequency. However, for a given input
condition, the deviation will be repeatable from
pulse to pulse. Contact technical support at Data
Delay Devices if your application requires device
testing at a specific input condition.
POWER SUPPLY BYPASSING
The DDU4F relies on a stable power supply to
produce repeatable delays within the stated
tolerances. A 0.1uf capacitor from VCC to GND,
located as close as possible to the VCC pin, is
recommended. A wide VCC trace and a clean
ground plane should be used.
DEVICE SPECIFICATIONS
TABLE 1: ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL MIN MAX UNITS NOTES
DC Supply Voltage V
CC
-0.3 7.0 V
Input Pin Voltage V
IN
-0.3 VDD+0.3 V
Storage Temperature T
STRG
-55 150 C
Lead Temperature T
LEAD
300 C 10 sec
TABLE 2: DC ELECTRICAL CHARACTERISTICS
(0C to 70C, 4.75V to 5.25V)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
High Level Output Voltage V
OH
2.5 3.4 V VCC = MIN, IOH = MAX
VIH = MIN, VIL = MAX
Low Level Output Voltage V
OL
0.35 0.5 V VCC = MIN, IOL = MAX
VIH = MIN, VIL = MAX
High Level Output Current I
OH
-1.0 mA
Low Level Output Current I
OL
20.0 mA
High Level Input Voltage V
IH
2.0 V
Low Level Input Voltage V
IL
0.8 V
Input Clamp Voltage V
IK
-1.2 V VCC = MIN, II = I
IK
Input Current at Maximum
Input Voltage
I
IHH
0.1 mA VCC = MAX, VI = 7.0V
High Level Input Current I
IH
20
µA
VCC = MAX, VI = 2.7V
Low Level Input Current I
IL
-0.6 mA VCC = MAX, VI = 0.5V
Short-circuit Output Current I
OS
-60 -150 mA VCC = MAX
Output High Fan-out 25 Unit
Output Low Fan-out 12.5 Load
Loading...