DADD DDU4C-5400, DDU4C-5300MC2, DDU4C-5300M, DDU4C-5300B2, DDU4C-5300A2 Datasheet

DDU4C

Doc #97034 DATA DELAY DEVICES, INC. 1

12/10/97 3 Mt. Prospect Ave. Clifton, NJ 07013

5-TAP, HCMOS-INTERFACED
FIXED DELAY LINE
(SERIES DDU4C)

FEATURES PACKAGES

• Five equally spaced outputs

• Fits standard 8-pin DIP socket

• Low profile

• Auto-insertable

• Input & outputs fully CMOS interfaced & buffered

• 10 T2L fan-out capability

FUNCTIONAL DESCRIPTION

The DDU4C-series device is a 5-tap digitally buffered delay line. The
signal input (IN) is reproduced at the outputs (T1-T5), shifted in time by an
amount determined by the device dash number (See Table). The total
delay of the line is measured from IN to T5. The nominal tap-to-tap delay
increment is given by one-fifth of the total delay.

SERIES SPECIFICATIONS

• Minimum input pulse width: 20% of total delay

• Output rise time: 8ns typical

• Supply voltage: 5VDC ± 5%

• Supply current: I

CCL

= 40µa typical

I

CCH

= 10ma typical

• Operating temperature: 0° to 70° C

• Temp. coefficient of total delay: 300 PPM/°C

20% 20% 20% 20% 20%

VDD GNDIN T1 T2 T3 T4 T5

DDU4C Functional diagram

1997 Data Delay Devices

data

delay
devices,

inc.



3

1

2
3
4
5
6
7

14

13
12
11
10

9
8

IN

N/C
N/C

T2

N/C

T4

GND

VDD

N/C
T1
N/C
T3
N/C
T5

14

12

10

8

1

4

6
7

IN

T2

T4

GND

VCC

T1

T3

T5

DIP
DDU4C-xx Comm.
DDU4C-xxM Military

SMD
DDU4C-xxA2 Comm.
DDU4C-xxB2 Comm.
DDU4C-xxMC2 Military

PIN DESCRIPTIONS

IN Signal Input
T1-T5 Tap Outputs
VDD +5 Volts
GND Ground

DASH NUMBER SPECIFICATIONS

Part

Number

Total

Delay (ns)

Delay Per

Tap (ns)

DDU4C-5050

50 ± 2.5 10.0 ± 3.0

DDU4C-5060

60 ± 3.0 12.0 ± 3.0

DDU4C-5075

75 ± 4.0 15.0 ± 3.0

DDU4C-5100

100 ± 5.0 20.0 ± 3.0

DDU4C-5125

125 ± 6.5 25.0 ± 3.0

DDU4C-5150

150 ± 7.5 30.0 ± 3.0

DDU4C-5200

200 ± 10.0 40.0 ± 4.0

DDU4C-5250

250 ± 12.5 50.0 ± 5.0

DDU4C-5300

300 ± 15.0 60.0 ± 6.0

DDU4C-5400

400 ± 20.0 80.0 ± 8.0

DDU4C-5500

500 ± 25.0 100.0 ± 10.0

NOTE: Any dash number between 5050 and 5500

not shown is also available.

DDU4C

Doc #97034 DATA DELAY DEVICES, INC. 2

12/10/97 Tel: [phone] Fax: [phone] http://www.datadelay.com

APPLICATION NOTES

HIGH FREQUENCY RESPONSE

The DDU4C tolerances are guaranteed for input
pulse widths and periods greater than those
specified in the test conditions. Although the
device will function properly for pulse widths as
small as 20% of the total delay and periods as
small as 40% of the total delay (for a symmetric
input), the delays may deviate from their values at
low frequency. However, for a given input
condition, the deviation will be repeatable from
pulse to pulse. Contact technical support at Data

Delay Devices if your application requires device
testing at a specific input condition.

POWER SUPPLY BYPASSING

The DDU4C relies on a stable power supply to
produce repeatable delays within the stated
tolerances. A 0.1uf capacitor from VDD to GND,
located as close as possible to the VDD pin, is
recommended. A wide VDD trace and a clean
ground plane should be used.

DEVICE SPECIFICATIONS

TABLE 1: ABSOLUTE MAXIMUM RATINGS

PARAMETER SYMBOL MIN MAX UNITS NOTES

DC Supply Voltage V

DD

-0.3 7.0 V

Input Pin Voltage V

IN

-0.3 VDD+0.3 V

Storage Temperature T

STRG

-55 150 C

Lead Temperature T

LEAD

300 C 10 sec

TABLE 2: DC ELECTRICAL CHARACTERISTICS

(0C to 70C, 4.75V to 5.25V)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

High Level Output Voltage V

OH

3.98 4.4 V VDD = 5.0, IOH = MAX
VIH = MIN, VIL = MAX

Low Level Output Voltage V

OL

0.15 0.26 V VDD = 5.0, IOL = MAX
VIH = MIN, VIL = MAX

High Level Output Current I

OH

-4.0 mA

Low Level Output Current I

OL

4.0 mA

High Level Input Voltage V

IH

3.15 V

Low Level Input Voltage V

IL

1.35 V

Input Current I

IH

0.10

µA

VDD = 5.0