Dacor MWDV308 User Manual
ERWD, EWD, IWD, MRWD, MWDV, MWDH,
Warming Drawer
Cooktop
1 1/2" (38 mm)
Typical counter top
3/4” Min.*
(19 mm)
120 Vac
electrical
receptacle
A
36" Typ.
(914 mm)
B
C
A
Warming Drawer
Warming Drawer
B
3/4" Min.*
(19 mm)
D
3/4" Min.*
(19 mm)
120 Vac
electrical
receptacle
36" Typ.
(914 mm)
C
C
27"/30"/36"
Dacor
single oven
Warming Drawer
Warming Drawer
Toe Kick
D
C
D
C
120 Vac
Elect.
120 Vac
Elect.
A
3/4" Min.*
(19 mm)
OWD, PWD Warming Drawers
Revised
03/04/09
24”, 27”, 30”, 36” Wide,
Warming Drawers
All tolerances: +1/16”, -0, (+1.6mm, -0) unless otherwise stated
PLANNING
1/3
WARNING
1.
Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.
This appliance must be installed in accordance with the
2.
accompanying installation instructions.
Electrical Circuit
Required
120 Vac, 60 Hz, 15 Amp
grounded, dedicated circuit
ELECTRICAL REQUIREMENTS
GUIDE
Total Connected
Load
0.5 kW (4.0 Amp)
Model (A) Cutout Width
ERWD30 28 1/2” (724 mm) 30 1/4” (768 mm) 9 1/8” (232 mm) 1 1/4” (32 mm)*
EWD24 22 1/2” (572 mm) 24 1/4” (616 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
EWD27 25 1/2” (648 mm) 27 1/4” (692 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
EWD30 28 1/2” (724 mm) 30 1/4” (768 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
EWD36 34 1/2” (876 mm) 36 1/4” (921 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
IWD24 22 1/2” (572 mm) *** 9 1/8” (232 mm) ***
IWD27 25 1/2” (648 mm) *** 9 1/8” (232 mm) ***
IWD30 28 1/2” (724 mm) *** 9 1/8” (232 mm) ***
MRWD27 25 1/2” (648 mm) 27 1/4” (692 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
MRWD30 28 1/2” (724 mm) 30 1/4” (768 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
MWDH27 25 1/2” (648 mm) 27 1/4” (692 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
MWDH30 28 1/2” (724 mm) 30 1/4” (768 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
MWDV27 25 1/2” (648 mm) 27 1/4” (692 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
MWDV30 28 1/2” (724 mm) 30 1/4” (768 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
OWD24 22 5/8” (575 mm) 24 1/4” (616 mm)** 11 15/16” (303 mm) 3/4” (19 mm)** 20 1/8” (511 mm)
PWD27 25 1/2” (648 mm) 27 1/4” (692 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
PWD30 28 1/2” (724 mm) 30 1/4” (768 mm)* 9 1/8” (232 mm) 1 1/4” (32 mm)*
* Bare minimum spacing to allow for ventilation and avoid scraping on EWD, MW and PWD series models. See *** below for spacing
for IWD series or OWD24 with custom front panel.
** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to allow for ventilation and avoid scraping. Gap
above and below cutout is 3/4” minimum.
*** On IWD series models or OWD24 without optional front panel kit: Height and width of custom front panel must exceed the chassis
face dimensions on page 3 to cover face of unit. Dimension (B) above = custom front panel width + 1/4” (6 mm). Dimension (D) above
= [custom front panel height - (C) Cutout Height] + 1/4” (6 mm) or 3/4” (19 mm) whichever is larger. Gap above and below cutout is
(D)/2 or 3/4” (19 mm) whichever is larger.
Web: http://www.Dacor.com
Corporate Phone: 800-793-0093
(B) Min. Width to
Adjacent Doors/
Drawers
(C) Cutout Height
CUTOUTS DIMENSIONS
Specifications are subject to change without notice.
See installation instructions for additional details.
(D) Min. Vertical Gap
Between Cutouts
Min. Cutout
Depth
24” (610 mm)
24” (610 mm)
2.1
23 3/8"
(594 mm)
Chassis
Drawer open
5/64"
(2mm)
23 13/16
(605 mm)
B
C
10 1/8"
(257 mm)
A
3 7/16"
(87 mm)
EWD
3 1/4"
(83 mm)
MRWD30B
(only)
MWDH/V
1"
(25mm)
3 1/2"
(89 mm)
ERWD
1 1/8"
(29 mm)
1 7/16"
(37 mm)
All other
MRWD series
1"
(25 mm)
PWD
2 1/4"
(57 mm)
1"
(25 mm)
1"
(25 mm)
10"
(254 mm)
9"
(229 mm)
1/2"
(13 mm)
1/2"
(13 mm)
Chassis without
drawer inserted
Mounting
Hole 9 Places
40" (1016 mm)
3 prong
120 Vac power cord
ERWD, EWD, IWD, MRWD, MWDV, MWDH,
OWD, PWD Warming Drawers
Revised
24”, 27”, 30”, 36” Wide,
03/04/09
HANDLE DIMENSIONS
Warming Drawers
All tolerances: ±1/16” (±1.6mm) unless otherwise stated
PLANNING
2/3
DRAWER FACE DIMENSIONS
(MWD SERIES SHOWN)
GUIDE
OVERALL DIMENSIONS
TOP VIEW
(EWD SERIES SHOWN)
Web: http://www.Dacor.com
Corporate Phone: 800-793-0093
CHASSIS DIMENSIONS
Model
(A) Drawer Face
Width
(B) Chassis Face
Width
(C) Chassis Width
ERWD30 30” (762 mm) 29 5/8” (752 mm) 28 1/4” (718 mm)
EWD24 24” (610 mm) 23 5/8” (600 mm) 22 1/4” (565 mm)
EWD27 27” (686 mm) 26 5/8” (676 mm) 25 1/4” (641 mm)
EWD30 30” (762 mm) 29 5/8” (752 mm) 28 1/4” (718 mm)
EWD36 30” (762 mm) 35 5/8” (905 mm) 34 1/4” (870 mm)
MRWD27 27” (686 mm) 26 5/8” (676 mm) 25 1/4” (641 mm)
MRWD30 30” (762 mm) 29 5/8” (752 mm) 28 1/4” (718 mm)
MWDH27 27” (686 mm) 26 5/8” (676 mm) 25 1/4” (641 mm)
MWDH30 30” (762 mm) 29 5/8” (752 mm) 28 1/4” (718 mm)
MWDV27 27” (686 mm) 26 5/8” (676 mm) 25 1/4” (641 mm)
MWDV30 30” (762 mm) 29 5/8” (752 mm) 28 1/4” (718 mm)
PWD27 27” (686 mm) 26 5/8” (676 mm) 25 1/4” (641 mm)
PWD30 30” (762 mm) 29 5/8” (752 mm) 28 1/4” (718 mm)
WARMING DRAWER OVERALL DIMENSIONS
Specifications are subject to change without notice.
See installation instructions for additional details.
2.2
Loading...