Dacor DR3GIFS User Manual 2

DR30GS, DR30GFS, DR30GIS, DR3GIFS

1 1/8” (2.9 cm)

DR30GI[F]S:
1/4” (6.4 mm)

Front of open door
Front of knobs

Front panel
Rear of front panel

Backguard thickness

26 1/8” (66.4 cm)

28 9/16” (72.5 cm)

24” (61.0 cm)

3” (7.6 cm)
backguard*

DR30G[F]S:

Full stainless

steel side panels

DR30GI[F]S:

(removable)

partial stainless

steel side panels

3 1/4” (8.3 cm)

External handle

shown, some models

(see inside cover)

have integral handle

1” above trim

Grates extend

backguard*

6” (15.2 cm)

1 3/4” (4.4 cm) backguard*

*�

See table for compatibility

Product width:
29 7/8” (75.9 cm)

NOTE: Neither version is
compatible with a raised vent.

to

37”

(94.0 cm)

(88.9 cm)

35”

Backguard*

9” (22.9 cm)

45 9/16” (115.7 cm)

Document # PG05-007

All tolerances ±1/16” (±1.6 mm) unless otherwise noted.

Distinctive

All Gas Ranges

Revised 09/13/12 Page 1/4

™

30” Wide

PLANNING

GUIDE

WARNING

• Observe all governing codes and ordinances during planning
and installation. Contact your local building department for
further information.

• This appliance must be installed in accordance with the
accompanying installation instructions.

Part Number Description Compatibility

AER30GLBG Lowprole(13/4inch)

All specications subject to change without notice.

AERB30G03 3 Inch

AERB30G06 6 Inch

AERB30G09 9 Inch

OVERALL DEPTH DIMENSIONS - SIDE VIEW

AVAILABLE BACKGUARDS

Standard on models DR30GIS, DR30GIFS
Optional on models DR30GS, DR30GFS

Optional on models DR30GS, DR30GFS
NOT compatible with models DR30GIS, DR30GIFS

Standard on models DR30GS, DR30GFS
NOT compatible with models DR30GIS, DR30GIFS

Optional on models DR30GS, DR30GFS
NOT compatible with models DR30GIS, DR30GIFS

Phone: [phone]www.dacor.com

Document # PG05-007

DR30GS, DR30GFS, DR30GIS, DR3GIFS

Revised 09/13/12 Page 2/4

Distinctive 30” Wide

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

B

13” (33.0 cm)

max.

4

14” (35.6 cm)

4

min.

Note 1

Back wall
immediately
behind range

6

A

All Gas Ranges

Top of
finished
counter

Note 5

Suggested
location of

3

utilities

PLANNING

GUIDE

■ Failure to meet or exceed the maximum and
minimum dimensions/clearances stated may result
in a fire hazard.

■ The range should be placed away from drafts that
may be caused by doors, windows and heating and
air conditioning outlets.

■ To eliminate the risk of burns or fire by reaching
over heated surface units, cabinet storage space
located above surface units should be avoided. If
cabinet storage space is to be provided directly
above the range, the risk of personal injury may be
reduced by installing a range hood.

■ In all instances, installation of a range hood is highly
recommended. The hood should project horizontally
a minimum of five (5) inches beyond the face of
the cabinets. See the range hood specifications for
minimum clearances.

■ The range may be installed flush to the rear wall.
See diagram and notes for rear wall surface
requirements. It is not necessary to install non­combustible materials behind the range below the
countertop height.

■ Any openings in the wall behind the appliance or in
the floor underneath it must be sealed.

Note 2

C

A* B

30” min.

(76.2 cm)

* See the cutout dimensions on following page for self-rimming installations.

FREESTANDING INSTALLATION CABINET CUTOUT DIMENSIONS - MODELS DR30GS, DR30GFS, DR30GIS AND DR30GIFS

1

30” (76.2 cm) min. vertical clearance from top of range grates to bottom of uncovered wood or metal cabinet. 24” (61 cm) min. clearance if bottom of
wood or metal cabinets are protected by not less than 1/4“ (0.6 cm) flame retardant millboard covered with no less than No. 28 MSG sheet steel 0.015”
(0.04 cm) stainless steel, or 0.024” (0.06 cm) aluminum or 0.020” (0.05cm) copper. 30” (76.2 cm) min. clearance between top of range grates and bottom
of unprotected wood or metal cabinet. If installing range hood, check the hood specifications for minimum required clearances.

2

Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See Product Dimensions.

3

Consult local code and following pages for requirements.

4

This specification not applicable for cabinets more than a horizontal distance of 10” (25.4 cm) from edge of range.

5

10” (25.4 cm) min. to combustible sidewalls above range (both sides).

6

Non-combustible surface required for models DR30GIS and DR30GIFS up to vertical distance specified in note 1 or range hood, whichever is lower. Non­combustible surface recommended, but not required, for models DR30GS and DR30GFS.

36” (91.4 cm) recommended

30” (76.2 cm) min.

C

37” (94.0 cm)

max.

All specications subject to change without notice.

Phone: [phone]www.dacor.com

Document # PG05-007

cm)�

10” min. (25.4 cm)

DR30GS, DR30GFS, DR30GIS, DR3GIFS

Revised 09/13/12 Page 3/4

Distinctive 30” Wide

SELF-RIMMING INSTALLATION CUTOUT OPTIONS (MODELS DR30GIS AND DR30GIFS ONLY)

All tolerances +1/16” (+1.6 mm), -0 unless otherwise noted.

10” min. (25.4 cm)
to any combustibles
above counter both sides

25 5/8”

max.

(65.1 cm)

29 1/4” (74.3 cm)

countertop opening

30” (76.2 cm)

cabinet opening

below countertop

Notch countertop

to width of cabinets

Cabinet face

below countertop

Non-combustible
rear wall required

20 3/4”

(52.7 cm)

All Gas Ranges

For all self-rimming installations:

Countertop height: 34 3/4” (88.3 cm) min.
36 7/8” (93.7 cm) max.
Countertop thickness: 1 5/8” (4.1 cm) max.

10” min. (25.4 cm)

*

21”

(53.3

to

24”

(61.0 cm)

to any combustibles
above counter both sides

25 3/4”

(65.4 cm)

max.

Countertop front

Rear wall or
countertop edge

29 1/4” (74.3 cm)

countertop opening

30” (76.2 cm)

cabinet opening

below countertop

Notch countertop

to width of cabinets

Cabinet face

below countertop

PLANNING

GUIDE

*

3/4” min. (1.9 cm)

countertop overhang

20 7/8”

(53.0 cm)

21 1/8”

(53.7 cm)

to

24 1/8”

(61.3 cm)

CABINETS LESS THAN 24” DEEP, 3 1/4” SIDE PANELS

INSTALLED, RANGE BACK FLUSH TO WALL (TOP VIEW)

to any combustibles
above counter both sides

CABINET EXACTLY 24” DEEP, 3 1/4” SIDE PANELS

REMOVED, RANGE BACK FLUSH TO WALL (TOP VIEW)

29 1/4” (74.3 cm)

countertop opening

30” (76.2 cm)

cabinet opening

below countertop

Cabinet face

below countertop
Notch countertop

overhang to width of

cabinets

Non-combustible
rear wall required

Countertop overhang

1 5/8” (4.1 cm) max.

*

24”

(61.0 cm)

CABINET DEPTH GREATER THAN 24” **

3 1/4” SIDE PANELS INSTALLED, RANGE BACK

OVERHANGING COUNTERTOP (TOP VIEW)

10” min. (25.4 cm)
to any combustibles
above counter both sides

29 1/4” (74.3 cm)

countertop opening

30” (76.2 cm)

cabinet opening

below countertop

Cabinet face

below countertop
Notch countertop

overhang to width of

CABINET DEPTH GREATER THAN 24” **

3 1/4” SIDE PANELS REMOVED, RANGE BACK

OVERHANGING COUNTERTOP (TOP VIEW)

Rear wall or
countertop edge

cabinets

*

3/4” min. (1.9 cm)

Countertop overhang

24 1/8”

(61.3 cm)

Countertop overhang

1 5/8” (4.1 cm) max.

* On models DR30GIS and DR30GIS, non-combustible surface required immediately behind range, as specified on previous page, when back of
backguard is less than 2 1/2” (6.4 cm) from rear wall.

** Models DR30GIS and DR30GIS include self-rimming trim piece that attaches to back of range and covers the edge of the countertop overhang in back.

*** To create a “built-in look” on the front of the cabinet, this dimension may be changed to 29 1/4” (74.3 cm). This configuration is only for models
DR30GIS and DR30GIS with side panels behind door removed.

All specications subject to change without notice.

Phone: [phone]www.dacor.com

Document # PG05-007

DR30GS, DR30GFS, DR30GIS, DR3GIFS

Revised 09/13/12 Page 4/4

12” (30.5 cm)

10” (25.4 cm)

Distinctive 30” Wide

All Gas Ranges

(31.1 cm)

10” (25.4 cm)

(36.2 cm)

12 1/4”

to

14 1/4”

PLANNING

GUIDE

6’ (183 cm)
long

2 1/2”

(6.4 cm)

3 1/2”

(8.9 cm)

ELECTRICAL REQUIREMENTS

Electrical Circuit

Required

120 Vac, 60 Hz, 15 Amps.,

dedicated, grounded

1” (2.5 cm)

4 1/4”

(10.8 cm)

BACK OF RANGEUTILITY CLEARANCE BEHIND RANGE

GAS SUPPLY PRESSURE REQUIREMENTS

Total Connected

Load

4.0 Amps. @

120 Vac, 60 Hz

IMPORTANT: The information above is for reference only. If the above
data does not agree with the product data label, use the data on the
product data label.

The gas inlet on the regulator accommodates a 1/2” NPT gas line
connection. The range can also accommodate a 3/4” NPT gas line
connection by removing the 1/2” to 3/4” adapter on the regulator inlet.

Gas

Type

Natural 5” 6” 1/2 psi

LP 10” 11” 1/2 psi

Manifold

Pressure* (WC)

Min. Gas Supply

Pressure (WC)

Max. Input

Pressure

All specications subject to change without notice.

Phone: [phone]www.dacor.com