DÜRR Periomat Plus Installation manual
Periomat Plus
Installation and Operating Instructions
EN
9000-600-11/30
2010/08
Content
Important Information
1. Warnings and Symbols . . . . . . . . . . . . . 4
2. General . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Note on Conformity . . . . . . . . . . . . . 5
2.2 General Notes . . . . . . . . . . . . . . . . . 5
2.3 Disposal . . . . . . . . . . . . . . . . . . . . . 5
2.4 Notes on medical products . . . . . . . . 5
2.5 Notes on EMC and medical products 6
2.6 Correct Usage . . . . . . . . . . . . . . . . . 6
2.7 Incorrect usage . . . . . . . . . . . . . . . . 6
2.8 Connecting peripheral appliances . . . 6
3. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1 General Safety Notes . . . . . . . . . . . . 6
3.2 Electrical safety instructions . . . . . . . 6
4. Delivery Contents . . . . . . . . . . . . . . . . . 9
4.1 Special accessories . . . . . . . . . . . . . 9
4.2 Disposable materials . . . . . . . . . . . . 9
5. Technical Data . . . . . . . . . . . . . . . . . . 10
5.1 Model Overview . . . . . . . . . . . . . . . 10
5.2 Model identification plate . . . . . . . . 10
5.3 Ambient conditions . . . . . . . . . . . . . 11
6. Switch panel functions . . . . . . . . . . . 11
Mounting
7. Set-up . . . . . . . . . . . . . . . . . . . . . . . . 12
7.1 Room for Set-up . . . . . . . . . . . . . . 12
7.2 Set-up . . . . . . . . . . . . . . . . . . . . . . 12
8. Start-up . . . . . . . . . . . . . . . . . . . . . . . . 12
8.1 Prepare the appliance . . . . . . . . . . . 12
9. Circuit diagram . . . . . . . . . . . . . . . . . . 16
9.1 Descriptions . . . . . . . . . . . . . . . . . . 17
9.2 Connection colours . . . . . . . . . . . . 17
Use
10. Chemical preparation . . . . . . . . . . . . . 18
11. Instructions for use . . . . . . . . . . . . . . . 19
11.1 Film insertion without adapter . . . . 19
11.2 Film insertion with adapter . . . . . . . 21
11.3 Miscellaneous . . . . . . . . . . . . . . . . 24
12. Maintenance . . . . . . . . . . . . . . . . . . . . 25
12.1 Weekly 2 x water
change and check level of chemi-
cals. . . . . . . . . . . . . . . . . . . . . . . . 25
12.2 Every 3 weeks change chemicals . 27
12.3 Every 6 months clean the film
transport . . . . . . . . . . . . . . . . . . . . 28
EN
2010/08 3
Important Information
1. Warnings and Symbols
Warnings
The warning notes in this document are designed to point out possible hazards which could
cause either injury to staff or damage to the
appliance.
They are marked using the following warning
EN
symbols:
Further symbols used
These symbols are used in this documentation
and /or on the appliance:
Notes, e.g. special instructions concerning efficient usage of the appliance.
Unplug at the mains and remove all
power.
Observe the instruction documentation
supplied
Date of manufacture
General warning symbols
Warning - dangerous electrical voltage
Danger to health
The safety instructions are laid out in the
following way:
SIGNAL WORD
Description of type and cause of
hazard
Description of possible outcomes if
safety notes are ignored
• Observe these measures to prevent
any possible danger occuring.
The safety instructions are graded in four levels
of danger:
DANGER Extremely hazardous and
could lead to serious injury
or death
WARNING Possibly hazardous but could
lead to serious injury or death
CAREFUL Could lead to minor injury
ATTENTION Could lead to serious damage
Dispose of this appliance correctly
according to EU directive (2002/96/
EG-WEE).
Handling instructions
Handling instructions are marked with a dot:
• Execute this handling step.
4 2010/08
2. General
2.1 Note on Conformity
This product has been tested for conformity
according to the appropriate directives as laid
down by the European Union and has been
found to conform to all the required specifications.
2.2 General Notes
• These Installation and Operating Instructions
form an integral part of the unit. They must
be kept close to the unit at all times. Precise
observance of these instructions is a precondition for use of the unit for the intended
purpose and for its correct operation.
New personnel must be made aware of the
contents, and they should be passed on to
future operating staff.
• Safety for the operator as well as troublefree operation of the unit are only ensured
if use is made of original equipment parts.
Additionally, only parts specifically referred to in these Installation and Operating
Instructions or accessories and disposable
materials specifically recommended by Dürr
Dental may be used. If other accessories or
disposable materials are used with this appliance, Dürr Dental cannot guarantee safe
operation or proper functioning. No liability on
the part of the manufacturer will be accepted
in the case that damage arises through the
use of non-approved accessories.
• Dürr Dental are only responsible for the equipment with regard to safety, reliability and proper functioning where assembly, resettings,
changes or modifications, extensions and
repairs have been carried out by Dürr Dental
or an agency authorized by Dürr Dental and if
the equipment is used in conformity with the
Installation and Operating Instructions.
• These Installation and Operating Instructions
conform to the relevant version of the equipment and the underlying safety standards
valid at the time of going to press. All circuits,
processes, names, software and appliances
quoted are protected under industrial property rights.
• The translation of these Installation and
Operating Instructions has been carried out
in good faith. No liability can be accepted
for mistakes in the translation. The enclosed German version of these Installation
and Operating Instructions is the reference
2010/08 5
version. If there is any doubt about the translation please consult your dealer.
• Any reprinting of the technical documentation,
in whole or in part, is subject to prior approval
of Dürr Dental being given in writing.
• Retain the packaging for possible return of the
product to the manufacturers. Only the original packaging provides adequate protection
during transport of the unit.
Should return of the product to the manufacturers be necessary during the guarantee
period, Dürr Dental accepts no responsibility
for damage occurring during transport where
the original packaging was not used!
Ensure that the packaging is kept out of the
reach of children.
2.3 Disposal
2.3.1 Appliance
• EU directive 2002/96/EG - WEEE (Waste
Electric and Electronic Equipment) of 27th
January 2003 and its current implementation
state that under national law Dental Products
are covered by the said directive and therefore, within the European Union, must be disposed of as special waste.
• If you have any questions at all concerning
the proper disposal of this product, please
contact either Dürr Dental directly or your usual specialist dental trader.
2.3.1 X-ray chemicals
Observe any local or national rules and regulations concerning disposal of x-ray chemicals.
2.4 Notes on medical products
• This product is a technical medical appliance and, as such, may only be operated by
such persons who, as a result of training or
experience, can be confidently expected to
operate it correctly and safely for patients and
staff alike.
• Do not lie multi-socket units on the floor.
When using portable multiple socket-outlets
then the requirements as laid out under
EN 60601-1-1 must be observed.
• Other systems should not be plugged into the
same multi-socket unit.
EN
2.5 Notes on EMC and medical products
Medical products should be treated with respect
when it comes to electro-magnetic compatibility
and special safety measures must be taken.
Special instructions concerning electro-magnetic compatibility for medical products can
be found in our special leaflet, order number
9000-606-67/30, or the information can be
found on the internet (www.duerr.de) in the
Technical Documentation download pages.
2.6 Correct Usage
EN
The Periomat Plus is designed for the development of intraoral X-ray films of sizes 2 x 3cm to
5.7 x 7.6cm.
2.7 Incorrect usage
Any use of this appliance/these appliances
above and beyond that laid down in the Installation and Operating Instructions is deemed to
be incorrect usage. The manufacturer cannot
be held liable for any damage resulting from
incorrect usage. The operator will be held liable
and bears all risks.
2.8 Connecting peripheral appliances
Appliances may only be connected together
or connected to any other assemblies where
complete and utter safety of the patients, operators and staff and of the environment will not be
affected in any way.
Where any doubts remain concerning the safety
when connecting to other units then the operator is obliged to ascertain that such connection
can in no way affect the safety of operator,
patient or other staff by referring to the manufacturer or a fully qualified and competent expert.
3. Safety
3.1 General Safety Notes
This appliance has been so designed and developed by Dürr Dental that under correct usage
that there can be no danger to operator or
patient. In spite of this, we feel it is our duty to
mention the following safety measures in order
to prevent any possible danger.
• When using this appliance all local and relevant regulations must be observed!
Converting or modifying the appliance in any
way is strictly prohibited. In such cases, any
and all guarantees immediately become invalid. The operation of modified appliances
can be punishable by law. In the interests of
trouble-free operation the operator is responsible for observing these regulations.
• Installation must be carried out by a technical
expert.
• Before every use the operator must check
the functional safety and the condition of the
appliance.
• The operator must be knowledgeable in the
operation of the appliance.
• The product is not designed to be used in
medical treatment areas where there exists
the danger of explosion. Areas where explosions could occur are those where flammable
anesthetic material, skin cleansers, oxygen
and skin disinfectants are present. This appliance is not to be used in areas where the
atmosphere could cause fire.
3.2 Electrical safety instructions
• The appliance may only be connected to an
earthed safety socket.
• Before connecting to the electricity supply the
appliance must be inspected and checked
that the supply voltage and the supply frequency correspond to that of the local electrical supply.
• Before initial use and start-up the appliance
and all supply lines must be checked for any
signs of damage. Damaged supply lines and
connections must be replaced immediately.
• Never come into contact with patients and
open plug-in connections on the appliance at
the same time.
• When using the appliance observe all the relevant electrical safety procedures.
6 2010/08
EN
2010/08 7
11a
1
11b
11
EN
10
2
3
4
5
9
8
7
6
14
16
11c 11d
12
13
15
17
1 2
18
19
3
8 2010/08
4. Delivery Contents
Model 1307-01 (230V, 50Hz)
Periomat Plus with daylight top, and heating
or
Model 1308-01 (230V, 50Hz)
Periomat Plus without daylight top,
with heating
1 Daylight top,
only model 1307-01 . . . . . . . . . 1304-700-00
2 Waste container . . . . . . . . . . . . 1303-000-06
3 Protective cover . . . . . . . . . . . . 1307-981-00
4 Cover for loading slot . . . . . . . . 1303-000-05
5 Film transport . . . . . . . . . . . . . . 1307-300-00
6 Water tank . . . . . . . . . . . . . . . . 1307-007-00
7 Fixer tank . . . . . . . . . . . . . . . . . 1303-000-09
8 Developer tank . . . . . . . . . . . . . 1303-000-08
9 Appliance base . . . . . . . . . . . . 1303-000-06
10 Periomat Intra,
X-ray chemicals . . . . . . . . . . CXB200C9940
11 Adapter for films,
11a 2 x 3.5 cm (3x) . . . . . . . . . 1303-000-01
11b 2,4 x 4 cm (3x) . . . . . . . . . 1303-000-18
11c 5,7 x 7,6 cm (1x) . . . . . . . 1303-000-22
11d 4 x 5 and 2,7 x 5,4 cm
(je1x) . . . . . . . . . . . . . . . . 1303-000-02
12 Film collector . . . . . . . . . . . . . . 1303-001-00
13 Drip pan . . . . . . . . . . . . . . . . . . 1303-000-13
14 Sponges grey (2 x) . . . . . . . . . 1303-000-06
Sponge red (1 x) . . . . . . . . . . . 1303-000-05
15 Light protection hood for
loading slot . . . . . . . . . . . . . . . 1303-000-14
16 Filling flange . . . . . . . . . . . . . . . 1307-001-00
17 Waste water drainage hose . . . 1307-000-07
- Operating Instructions . . . . . 9000-600-11/..
4.2 Disposable materials
10 Periomat Intra,
X-ray chemicals . . . . . . . . . . CXB200C9940
20 Periomat Intra/C,
X-ray chemicals . . . . . . . . . . CXB210C9940
21 Universal Cleaner,
Double pack . . . . . . . . . . . . CCB600C5540
22 WR 2000 Spray cleaner,
Six pack . . . . . . . . . . . . . . . . CCB800C5540
EN
10
20
21
4.1 Special accessories
The parts listed as special accessories
are not part of the standard scope of
delivery but can be ordered separately.
18 Perioclean-Set
for film transport cleaning . . . . . 1304-070-00
19 Container, double tray . . . . . . . 1303-000-16
22
4
2010/08 9
5. Technical Data
5.1 Model Overview
Model 1307-01 (230V, 50Hz)
Periomat Plus with daylight top, and heating
Model 1308-01 (230V, 50Hz)
Periomat Plus without daylight top, with
heating
EN
Model
Voltage V 230
Frequency Hz 50
Rated current A 2,2
Rated power W 500
Duty cycle %ED 100
Film processing
time min 5
Developing
temperature
Warm-up time min /
Heating V 24
Appliance fuse A T 2.5
Volume
D eveloper tank l 1
Fixer tank l 1
Water tank l 1,25
5
Weight kg 11,2 / 10,2
Dimensions
(HxBxT)
1307-01 / 1308-01
°C 25
~7
°C
cm 40 x 63 x 25
(1307-01)
22 x 63 x 25
(1308-01)
5.2 Model identification plate
The model identification plate can be found on
the rear side of the appliance under the protective cover.
REF Order no.. / Model no..
SN Serial no.
6
10 2010/08
Loading...