Cytech KP04 Installation Manual

KP04 LCD

Keypad

Installation

Manual

KP04 LCD Keypad Installation Manual

Introduction.................................................................................1

Upgrading from KP01 and KP02.............................................. 1

Specifications............................................................................ 2

System Requirements................................................................ 2

Contents .................................................................................... 2

Set-Up...........................................................................................2

Connections............................................................................... 2

Cables........................................................................................ 3

Jumper Settings......................................................................... 3

Keypad ID Switch.....................................................................3

LED Indicators..........................................................................3

Installation ...................................................................................4

Vocabulary Programming..........................................................5

Tabs...........................................................................................6

Event Log Sentences.................................................................6

Miscellaneous Sentences ..........................................................7

Special Words ........................................................................... 8

Settings...................................................................................... 8

Menu Bar ..................................................................................9

File ........................................................................................ 9

Edit........................................................................................ 9

Transfer .................................................................................9

Help.......................................................................................9

Toolbar.................................................................................... 10

Changing Configuration.......................................................... 10

Downloading...........................................................................12

Comfort II Downloading......................................................... 13

Version History .........................................................................14

KP04 LCD Keypad Installation Manual

1

Introduction

The KP04 Keypad incorporates a 2 lines x 16 character Liquid Crystal Display
(LCD), enabling Comfort messages to be displayed. This allows users to see
alarms, zones and warning messages without the need to sign-in to listen to
the voice menu. The KP04, like a KP01/02 keypad also has a comprehensive
voice menu. A key difference between KP04 and non-LCD versions is that
the Event Log is displayed as well as announced. The words in the LCD
keypad can also be customised according to the wordlist and vocabulary in
Comfort using the VoiceProc Software. The KP04 Keypad also receives
Infrared codes from the RC01 handheld remote control or a universal
remote control such as the Philips Pronto®, allowing responses to be
activated to control home appliances or act as a hand-held keypad in the
same way as the KP02. A feature of the KP04 is its real time display of
active zones and alarms. Hence a trouble alarm like “Phone Trouble” will be
displayed on the LCD. For Communications Failures, the name of the device
will be displayed e.g. “UCM 2”, “Keypad 3”, “Door Station 1”, Slave 1”
instead of the more cryptic Communications Failure ID number.

Note that from Comfort II firmware version 5.039 onwards, the
Event Log will be both displayed and read out from the KP04.

Upgrading from KP01 and KP02

The KP04 can replace KP01s and KP02s in existing installations. Mounting
holes are identical to the KP01/KP02, and the same wiring from Comfort to

KP04 LCD Keypad Installation Manual

2

the Keypads can be used. However, each wire pair (KA/KB, MIC/Voice,
12V/COM) is reversed when connecting to the terminal blocks. This change
was decided to standardize the connections for all Comfort terminals (Main,
UCM, Slave Keypads etc).

For Comfort I, firmware should be Outside (PRO) or Action (ULTRA) 4.226
or above. The firmware can be upgraded by purchasing the IC01-OUT or
IC01-ACT and replacing the U1 IC on Comfort. The KP04 cannot be used
with Comfort ENTRY. All Comfort II firmware versions are compatible with
KP04

A notable difference between the KP04 and KP01/KP02 is the volume control
increases the volume in the downward position, corresponding to the normal
direction of radios and other audio equipment.

Specifications

• Dimensions: 89 (W) x 160 (H) x 31 (D) mm

• Weight: 177 g

• Power Supply: 12V DC from Comfort System

• Current Consumption: 50 mA idle (without voice)

• Comfort IR codes received: 0 to 127

System Requirements

• Comfort system with firmware version “Outside or Action 4.226” and
above. Comfort ENTRY systems cannot be used with the KP04

• UCM01 with firmware version “UCM5.72” and above for
downloading programmed vocabulary.

Contents

The KP04 LCD Keypad package consists of the following*:

• KP04 Keypad

• KP04 Manual (this booklet)

• 2 wall plugs and screws for mounting.

• 3 x 2 way removable terminal blocks

*Subject to changes without prior notice

Set-Up

Connections

• JP1 – 12V/COM connector. Connected to 12V/COM on Comfort.

• JP2 – KA/KB connector. Connected to KA/KB on Comfort.

• JP3 – VOICE/MIC connector. Connected to VOICE/MIC on Comfort.