Cypress Semiconductor CY7C1511KV18, CY7C1513KV18, CY7C1526KV18, CY7C1515KV18 User Manual

72-Mbit QDR™-II SRAM 4-Word

Burst Architecture

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Features

Configurations

■ Separate Independent Read and Write Data Ports
❐ Supports concurrent transactions

■ 333 MHz Clock for High Bandwidth

■ 4-word Burst for Reducing Address Bus Frequency

■ Double Data Rate (DDR) Interfaces on both Read and Write

Ports (data transferred at 666 MHz) at 333 MHz

■ Two Input Clocks (K and K) for precise DDR Timing
❐ SRAM uses rising edges only

■ Two Input Clocks for Output Data (C and C) to minimize Clock

Skew and Flight Time mismatches

■ Echo Clocks (CQ and CQ) simplify Data Capture in High Speed

Systems

■ Single Multiplexed Address Input Bus latches Address Inputs

for Read and Write Ports

■ Separate Port Selects for Depth Expansion

■ Synchronous Internally Self-timed Writes

■ QDR™-II operates with 1.5 Cycle Read Latency when DOFF

is asserted HIGH

■ Operates similar to QDR-I Device with 1 Cycle Read Latency

when DOFF

■ Available in x8, x9, x18, and x36 Configurations

■ Full Data Coherency, providing Most Current Data

■ Core V
❐ Supports both 1.5V and 1.8V IO supply

■ Available in 165-ball FBGA Package (13 x 15 x 1.4 mm)

■ Offered in both Pb-free and non Pb-free Packages

■ Variable Drive HSTL Output Buffers

■ JTAG 1149.1 Compatible Test Access Port

■ Phase Locked Loop (PLL) for Accurate Data Placement

is asserted LOW

= 1.8V (±0.1V); IO V

DD

= 1.4V to V

DDQ

DD

CY7C1511KV18 – 8M x 8

CY7C1526KV18 – 8M x 9

CY7C1513KV18 – 4M x 18

CY7C1515KV18 – 2M x 36

Functional Description

The CY7C1511KV18, CY7C1526KV18, CY7C1513KV18, and
CY7C1515KV18 are 1.8V Synchronous Pipelined SRAMs,
equipped with QDR-II architecture. QDR-II architecture consists
of two separate ports: the read port and the write port to access
the memory array. The read port has dedicated data outputs to
support read operations and the write port has dedicated data
inputs to support write operations. QDR-II architecture has
separate data inputs and data outputs to completely eliminate
the need to “turnaround” the data bus that exists with common
IO devices. Each port can be accessed through a common
address bus. Addresses for read and write addresses are
latched on alternate rising edges of the input (K) clock. Accesses
to the QDR-II read and write ports are independent of one
another. To maximize data throughput, both read and write ports
are equipped with DDR interfaces. Each address location is
associated with four 8-bit words (CY7C1511KV18), 9-bit words
(CY7C1526KV18), 18-bit words (CY7C1513KV18), or 36-bit
words (CY7C1515KV18) that burst sequentially into or out of the
device. Because data can be transferred into and out of the
device on every rising edge of both input clocks (K and K

), memory bandwidth is maximized while simplifying

and C
system design by eliminating bus “turnarounds”.

Depth expansion is accomplished with port selects, which
enables each port to operate independently.

All synchronous inputs pass through input registers controlled by
the K or K
registers controlled by the C or C

input clocks. All data outputs pass through output

(or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.

and C

Table 1. Selection Guide

Description 333 MHz 300 MHz 250 MHz 200 MHz 167 MHz Unit

Maximum Operating Frequency 333 300 250 200 167 MHz

Maximum Operating Current x8 600 560 490 430 380 mA

x9 600 560 490 430 380

x18 620 570 500 440 390

x36 850 790 680 580 510

Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600
Document Number: 001-00435 Rev. *E Revised March 30, 2009

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Logic Block Diagram (CY7C1511KV18)

2M x 8 Array

CLK

A

(20:0)

Gen.

K

K

Control

Logic

Address
Register

D

[7:0]

Read Add. Decode

Read Data Reg.

RPS

WPS

Control

Logic

Address
Register

Reg.

Reg.

Reg.

16

21

32

8

NWS

[1:0]

V

REF

Write Add. Decode

Write

Reg

16

A

(20:0)

21

8

CQ

CQ

DOFF

Q

[7:0]

8

8

8

Write

Reg

Write

Reg

Write

Reg

C

C

2M x 8 Array

2M x 8 Array

2M x 8 Array

8

CLK

A

(20:0)

Gen.

K

K

Control

Logic

Address
Register

D

[8:0]

Read Add. Decode

Read Data Reg.

RPS

WPS

Control

Logic

Address
Register

Reg.

Reg.

Reg.

18

21

36

9

BWS

[0]

V

REF

Write Add. Decode

Write

Reg

18

A

(20:0)

21

9

CQ

CQ

DOFF

Q

[8:0]

9

9

9

Write

Reg

Write

Reg

Write

Reg

C

C

2M x 9 Array

2M x 9 Array

2M x 9 Array

2M x 9 Array

9

Logic Block Diagram (CY7C1526KV18)

Document Number: 001-00435 Rev. *E Page 2 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Logic Block Diagram (CY7C1513KV18)

CLK

A

(19:0)

Gen.

K

K

Control

Logic

Address
Register

D

[17:0]

Read Add. Decode

Read Data Reg.

RPS

WPS

Control

Logic

Address
Register

Reg.

Reg.

Reg.

36

20

72

18

BWS

[1:0]

V

REF

Write Add. Decode

Write

Reg

36

A

(19:0)

20

18

CQ

CQ

DOFF

Q

[17:0]

18

18

18

Write

Reg

Write

Reg

Write

Reg

C

C

1M x 18 Array

1M x 18 Array

1M x 18 Array

1M x 18 Array

18

512K x 36 Array

CLK

A

(18:0)

Gen.

K

K

Control

Logic

Address
Register

D

[35:0]

Read Add. Decode

Read Data Reg.

RPS

WPS

Control

Logic

Address
Register

Reg.

Reg.

Reg.

72

19

144

36

BWS

[3:0]

V

REF

Write Add. Decode

Write

Reg

72

A

(18:0)

19

512K x 36 Array

512K x 36 Array

512K x 36 Array

36

CQ

CQ

DOFF

Q

[35:0]

36

36

36

Write

Reg

Write

Reg

Write

Reg

C

C

36

Logic Block Diagram (CY7C1515KV18)

Document Number: 001-00435 Rev. *E Page 3 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Pin Configuration

Note

1. NC/144M and NC/288M are not connected to the die and can be tied to any voltage level.

The pin configurations for CY7C1511KV18, CY7C1526KV18, CY7C1513KV18, and CY7C1515KV18 follow.

165-Ball FBGA (13 x 15 x 1.4 mm) Pinout

CY7C1511KV18 (8M x 8)

1 2 3 4 5 6 7 8 9 10 11

A CQ AAWPSNWS

1

B NC NC NC A NC/288M K NWS

C NC NC NC V

D NC D4 NC V

E NC NC Q4 V

F NC NC NC V

G NC D5 Q5 V

H DOFF V

REF

V

DDQ

V

J NC NC NC V

K NC NC NC V

L NC Q6 D6 V

M NC NC NC V

N NC D7 NC V

SS

SS

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

SS

SS

ANCAVSSNC NC D3

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

AAAVSSNC NC NC

P NC NC Q7 A A C A A NC NC NC

R TDO TCK A A A C AAATMSTDI

K NC/144M RPS AACQ

0

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

ANCNCQ3

V

SS

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

SS

[1]

NC NC NC

NC D2 Q2

NC NC NC

NC NC NC

V

DDQ

V

REF

NC Q1 D1

NC NC NC

NC NC Q0

NC NC D0

ZQ

CY7C1526KV18 (8M x 9)

1 2 3 4 5 6 7 8 9 10 11

A CQ AAWPSNC K NC/144M RPS AACQ

B NC NC NC A NC/288M K BWS

C NC NC NC V

D NC D5 NC V

E NC NC Q5 V

F NC NC NC V

G NC D6 Q6 V

H DOFF V

REF

V

DDQ

V

J NC NC NC V

K NC NC NC V

L NC Q7 D7 V

M NC NC NC V

N NC D8 NC V

SS

SS

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

SS

SS

ANCAVSSNC NC D4

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

AAAVSSNC NC NC

0

ANCNCQ4

V

V

V

V

V

V

V

V

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

V

SS

SS

NC NC NC

NC D3 Q3

NC NC NC

NC NC NC

V

DDQ

V

REF

NC Q2 D2

NC NC NC

NC NC Q1

NC NC D1

ZQ

P NC NC Q8 A A C A A NC D0 Q0

R TDO TCK A A A C AAATMSTDI

Document Number: 001-00435 Rev. *E Page 4 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Pin Configuration (continued)

The pin configurations for CY7C1511KV18, CY7C1526KV18, CY7C1513KV18, and CY7C1515KV18 follow.

165-Ball FBGA (13 x 15 x 1.4 mm) Pinout

CY7C1513KV18 (4M x 18)

1 2 3 4 5 6 7 8 9 10 11

A CQ NC/144M A WPS BWS

1

B NC Q9 D9 A NC K BWS

C NC NC D10 V

D NC D11 Q10 V

E NC NC Q11 V

F NC Q12 D12 V

G NC D13 Q13 V

H DOFF V

REF

V

DDQ

V

J NC NC D14 V

K NC NC Q14 V

L NC Q15 D15 V

M NC NC D16 V

N NC D17 Q16 V

SS

SS

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

SS

SS

ANCAVSSNC Q7 D8

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

AAAVSSNC NC D1

P NC NC Q17 A A C A A NC D0 Q0

R TDO TCK A A A C AAATMSTDI

K NC/288M RPS AACQ

0

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

ANCNCQ8

V

SS

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

DDQ

V

SS

[1]

NC NC D7

NC D6 Q6

NC NC Q5

NC NC D5

V

DDQ

V

REF

NC Q4 D4

NC D3 Q3

NC NC Q2

NC Q1 D2

ZQ

CY7C1515KV18 (2M x 36)

1 2 3 4 5 6 7 8 9 10 11

A CQ NC/288M A WPS BWS

B Q27 Q18 D18 A BWS

C D27 Q28 D19 V

D D28 D20 Q19 V

E Q29 D29 Q20 V

F Q30 Q21 D21 V

G D30 D22 Q22 V

H DOFF V

REF

V

DDQ

V

J D31 Q31 D23 V

K Q32 D32 Q23 V

L Q33 Q24 D24 V

M D33 Q34 D25 V

N D34 D26 Q25 V

SS

SS

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

SS

SS

ANCAVSSD16 Q7 D8

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

AAAVSSQ10 D9 D1

2

3

K BWS

RPS A NC/144M CQ

1

KBWS0AD17Q17Q8

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

SS

V

DD

V

DD

V

DD

V

DD

V

DD

V

SS

V

SS

V

V

V

V

V

V

V

V

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

DDQ

V

SS

SS

Q16 D15 D7

Q15 D6 Q6

D14 Q14 Q5

Q13 D13 D5

V

DDQ

V

REF

D12 Q4 D4

Q12 D3 Q3

D11 Q11 Q2

D10 Q1 D2

ZQ

P Q35 D35 Q26 A A C A A Q9 D0 Q0

R TDO TCK A A A C AAATMSTDI

Document Number: 001-00435 Rev. *E Page 5 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Pin Definitions

Pin Name I/O Pin Description

D

[x:0]

WPS Input-

NWS

,

0

NWS

,

1

BWS0,

,

BWS

1

BWS

,

2

BWS

3

A Input-

Q

[x:0]

RPS Input-

C Input Clock Positive Input Clock for Output Data. C is used in conjunction with C

C

K Input Clock Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the device

K

Input-

Synchronous

Data Input Signals. Sampled on the rising edge of K and K clocks when valid write operations are active.
CY7C1511KV18 − D
CY7C1526KV18 − D
CY7C1513KV18 − D
CY7C1515KV18 − D

[7:0]
[8:0]
[17:0]
[35:0]

Write Port Select − Active LOW. Sampled on the rising edge of the K clock. When asserted active, a

Synchronous

Input-

Synchronous

Input-

Synchronous

write operation is initiated. Deasserting deselects the write port. Deselecting the write port ignores D
Nibble Write Select 0, 1 − Active LOW (CY7C1511KV18 Only). Sampled on the rising edge of the K

and K

clocks

when write operations are active
the current portion of the write operations.
All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select
ignores the corresponding nibble of data and it is not written into the device

. Used to select which nibble is written into the device

NWS

controls D

0

and NWS1 controls D

[3:0]

[7:4]

.

.

during

Byte Write Select 0, 1, 2, and 3 − Active LOW. Sampled on the rising edge of the K and K clocks when
write operations are active. Used to select which byte is written into the device during the current portion
of the write operations. Bytes not written remain unaltered.
CY7C1526KV18 − BWS
CY7C1513KV18 − BWS0 controls D
CY7C1515KV18 − BWS0 controls D
BWS

controls D

2

All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select

[26:18]

ignores the corresponding byte of data and it is not written into the device

controls D

0

and BWS3 controls D

[8:0]

and BWS1 controls D

[8:0]

, BWS1 controls D

[8:0]

[35:27].

[17:9]

[17:9].

,

.

Address Inputs. Sampled on the rising edge of the K clock during active read and write operations. These

Synchronous

address inputs are multiplexed for both read and write operations. Internally, the device is organized as
8M x 8 (4 arrays each of 2M x 8) for CY7C1511KV18, 8M x 9 (4 arrays each of 2M x 9) for CY7C1526KV18,
4M x 18 (4 arrays each of 1M x 18) for CY7C1513KV18 and 2M x 36 (4 arrays each of 512K x 36) for
CY7C1515KV18. Therefore, only 21 address inputs are needed to access the entire memory array of
CY7C1511KV18 and CY7C1526KV18, 20 address inputs for CY7C1513KV18 and 19 address inputs for
CY7C1515KV18. These inputs are ignored when the appropriate port is deselected.

Outputs-

Synchronous

Data Output Signals. These pins drive out the requested data when the read operation is active. Valid
data is driven out on the rising edge of the C and C
single clock mode. On deselecting the read port, Q
CY7C1511KV18 − Q
CY7C1526KV18 − Q
CY7C1513KV18 − Q
CY7C1515KV18 − Q

[7:0]

[8:0]
[17:0]
[35:0]

clocks during read operations, or K and K when in

are automatically tristated.

[x:0]

Read Port Select − Active LOW. Sampled on the rising edge of positive input clock (K). When active, a

Synchronous

read operation is initiated. Deasserting deselects the read port. When deselected, the pending access is
allowed to complete and the output drivers are automatically tristated following the next rising edge of the
C clock. Each read access consists of a burst of four sequential transfers.

to clock out the read data from

the device. C and C

can be used together to deskew the flight times of various devices on the board back

to the controller. See Application Example on page 10 for further details.

Input Clock Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from

the device. C and C

can be used together to deskew the flight times of various devices on the board back

to the controller. See Application Example on page 10 for further details.

and to drive out data through Q
edge of K.

when in single clock mode. All accesses are initiated on the rising

[x:0]

Input Clock Negative Input Clock Input. K is used to capture synchronous inputs being presented to the device and

to drive out data through Q

when in single clock mode.

[x:0]

[x:0]

.

Document Number: 001-00435 Rev. *E Page 6 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Pin Definitions (continued)

Pin Name I/O Pin Description

CQ Echo Clock CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock

for output data (C) of the QDR-II. In the single clock mode, CQ is generated with respect to K. The timings
for the echo clocks are shown in the Switching Characteristics on page 24.

CQ

ZQ Input Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus

DOFF

TDO Output TDO for JTAG.

TCK Input TCK Pin for JTAG.

TDI Input TDI Pin for JTAG.

TMS Input TMS Pin for JTAG.

NC N/A Not Connected to the Die. Can be tied to any voltage level.

NC/144M N/A Not Connected to the Die. Can be tied to any voltage level.

NC/288M N/A Not Connected to the Die. Can be tied to any voltage level.

V

REF

V

DD

V

SS

V

DDQ

Echo Clock CQ Referenced with Respect to C. This is a free running clock and is synchronized to the input clock

Input PLL Turn Off − Active LOW. Connecting this pin to ground turns off the PLL inside the device. The timings

Input-

Reference

Power Supply Power Supply Inputs to the Core of the Device.

Ground Ground for the Device.

Power Supply Power Supply Inputs for the Outputs of the Device.

for output data (C
for the echo clocks are shown in the Switching Characteristics on page 24.

impedance. CQ, CQ, and Q
between ZQ and ground. Alternatively, this pin can be connected directly to V
minimum impedance mode. This pin cannot be connected directly to GND or left unconnected.

in the PLL turned off operation differs from those listed in this data sheet. For normal operation, this pin
is connected to a pull up through a 10 KΩ or less pull up resistor. The device behaves in QDR-I mode
when the PLL is turned off. In this mode, the device can be operated at a frequency of up to 167 MHz
with QDR-I timing.

Reference Voltage Input. Static input used to set the reference level for HSTL inputs, outputs, and AC
measurement points.

) of the QDR-II. In the single clock mode, CQ is generated with respect to K. The timings

output impedance are set to 0.2 x RQ, where RQ is a resistor connected

[x:0]

, which enables the

DDQ

Document Number: 001-00435 Rev. *E Page 7 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Functional Overview

The CY7C1511KV18, CY7C1526KV18, CY7C1513KV18,
CY7C1515KV18 are synchronous pipelined Burst SRAMs with a
read port and a write port. The read port is dedicated to read
operations and the write port is dedicated to write operations.
Data flows into the SRAM through the write port and flows out
through the read port. These devices multiplex the address
inputs to minimize the number of address pins required. By
having separate read and write ports, the QDR-II completely
eliminates the need to turn around the data bus and avoids any
possible data contention, thereby simplifying system design.
Each access consists of four 8-bit data transfers in the case of
CY7C1511KV18, four 9-bit data transfers in the case of
CY7C1526KV18, four 18-bit data transfers in the case of
CY7C1513KV18, and four 36-bit data transfers in the case of
CY7C1515KV18 in two clock cycles.

This device operates with a read latency of one and half cycles
when DOFF
connected to V
read latency of one clock cycle.

Accesses for both ports are initiated on the positive input clock
(K). All synchronous input timing is referenced from the rising
edge of the input clocks (K and K
enced to the output clocks (C and C
clock mode).

All synchronous data inputs (D
controlled by the input clocks (K and K
outputs (Q
rising edge of the output clocks (C and C
single clock mode).

All synchronous control (RPS
through input registers controlled by the rising edge of the input
clocks (K and K).

CY7C1513KV18 is described in the following sections. The
same basic descriptions apply to CY7C1511KV18,
CY7C1526KV18 and CY7C1515KV18.

pin is tied HIGH. When DOFF pin is set LOW or

then device behaves in QDR-I mode with a

SS

) and all output timing is refer-

, or K and K when in single

) pass through input registers

[x:0]

) pass through output registers controlled by the

[x:0]

, WPS, BWS

). All synchronous data

, or K and K when in

) inputs pass

[x:0]

from the rising edge of the output clock (C or C

, or K or K when
in single clock mode). To maintain the internal logic, each read
access must be allowed to complete. Each read access consists
of four 18-bit data words and takes two clock cycles to complete.
Therefore, read accesses to the device cannot be initiated on
two consecutive K clock rises. The internal logic of the device
ignores the second read request. Read accesses can be initiated
on every other K clock rise. Doing so pipelines the data flow such
that data is transferred out of the device on every rising edge of
the output clocks (C and C

, or K and K when in single clock

mode).

When the read port is deselected, the CY7C1513KV18 first
completes the pending read transactions. Synchronous internal
circuitry automatically tristates the outputs following the next
rising edge of the positive output clock (C). This enables a
seamless transition between devices without the insertion of wait
states in a depth expanded memory.

Write Operations

Write operations are initiated by asserting WPS active at the
rising edge of the positive input clock (K). On the following K
clock rise the data presented to D
the lower 18-bit write data register, provided BWS
asserted active. On the subsequent rising edge of the negative
input clock (K

) the information presented to D
into the write data register, provided BWS
active. This process continues for one more cycle until four 18-bit
words (a total of 72 bits) of data are stored in the SRAM. The 72
bits of data are then written into the memory array at the specified
location. Therefore, write accesses to the device cannot be
initiated on two consecutive K clock rises. The internal logic of
the device ignores the second write request. Write accesses can
be initiated on every other rising edge of the positive input clock
(K). Doing so pipelines the data flow such that 18 bits of data can
be transferred into the device on every rising edge of the input
clocks (K and K

).

When deselected, the write port ignores all inputs after the
pending write operations are completed.

is latched and stored into

[17:0]

[1:0]

is also stored

[17:0]

are both asserted

[1:0]

are both

Read Operations

The CY7C1513KV18 is organized internally as four arrays of 1M
x 18. Accesses are completed in a burst of four sequential 18-bit
data words. Read operations are initiated by asserting RPS
active at the rising edge of the positive input clock (K). The
address presented to the address inputs is stored in the read
address register. Following the next K clock rise, the corre­sponding lowest order 18-bit word of data is driven onto the
Q

using C as the output timing reference. On the subse-

[17:0]

quent rising edge of C, the next 18-bit data word is driven onto
the Q
are driven out onto Q

Document Number: 001-00435 Rev. *E Page 8 of 31

. This process continues until all four 18-bit data words

[17:0]

. The requested data is valid 0.45 ns

[17:0]

Byte Write Operations

Byte write operations are supported by the CY7C1513KV18. A
write operation is initiated as described in the Write Operations
section. The bytes that are written are determined by BWS

, which are sampled with each set of 18-bit data words.

BWS

1

Asserting the appropriate Byte Write Select input during the data
portion of a write latches the data being presented and writes it
into the device. Deasserting the Byte Write Select input during
the data portion of a write enables the data stored in the device
for that byte to remain unaltered. This feature is used to simplify
read, modify, or write operations to a byte write operation.

and

0

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Single Clock Mode

The CY7C1511KV18 is used with a single clock that controls
both the input and output registers. In this mode the device
recognizes only a single pair of input clocks (K and K) that control
both the input and output registers. This operation is identical to
the operation if the device had zero skew between the K/K

clocks. All timing parameters remain the same in this mode.

C/C
To use this mode of operation, the user must tie C and C
at power on. This function is a strap option and not alterable
during device operation.

and

HIGH

Concurrent Transactions

The read and write ports on the CY7C1513KV18 operate
independently of one another. As each port latches the address
inputs on different clock edges, the user can read or write to any
location, regardless of the transaction on the other port. If the
ports access the same location when a read follows a write in
successive clock cycles, the SRAM delivers the most recent
information associated with the specified address location. This
includes forwarding data from a write cycle that was initiated on
the previous K clock rise.

Read access and write access must be scheduled such that one
transaction is initiated on any clock cycle. If both ports are
selected on the same K clock rise, the arbitration depends on the
previous state of the SRAM. If both ports are deselected, the
read port takes priority. If a read was initiated on the previous
cycle, the write port takes priority (as read operations cannot be
initiated on consecutive cycles). If a write was initiated on the
previous cycle, the read port takes priority (as write operations
cannot be initiated on consecutive cycles). Therefore, asserting
both port selects active from a deselected state results in alter­nating read or write operations being initiated, with the first
access being a read.

Programmable Impedance

An external resistor, RQ, must be connected between the ZQ pin
on the SRAM and V
driver impedance. The value of RQ must be 5X the value of the
intended line impedance driven by the SRAM, the allowable
range of RQ to guarantee impedance matching with a tolerance
of ±15% is between 175Ω and 350Ω
output impedance is adjusted every 1024 cycles upon power up
to account for drifts in supply voltage and temperature.

to allow the SRAM to adjust its output

SS

, with V

=1.5V. The

DDQ

Echo Clocks

Echo clocks are provided on the QDR-II to simplify data capture
on high speed systems. Two echo clocks are generated by the
QDR-II. CQ is referenced with respect to C and CQ is referenced
with respect to C
nized to the output clock of the QDR-II. In the single clock mode,
CQ is generated with respect to K and CQ is generated with
respect to K

Switching Characteristics on page 24.

. These are free running clocks and are synchro-

. The timing for the echo clocks is shown in the

PLL

These chips use a PLL that is designed to function between
120 MHz and the specified maximum clock frequency. During
power up, when the DOFF
20 μs of stable clock. The PLL can also be reset by slowing or
stopping the input clocks K and K for a minimum of 30 ns.
However, it is not necessary to reset the PLL to lock to the
desired frequency. The PLL automatically locks 20 μs after a
stable clock is presented. The PLL may be disabled by applying
ground to the DOFF
behaves in QDR-I mode (with one cycle latency and a longer
access time).

is tied HIGH, the PLL is locked after

pin. When the PLL is turned off, the device

Depth Expansion

The CY7C1513KV18 has a port select input for each port. This
enables for easy depth expansion. Both port selects are sampled
on the rising edge of the positive input clock only (K). Each port
select input can deselect the specified port. Deselecting a port
does not affect the other port. All pending transactions (read and
write) are completed before the device is deselected.

Document Number: 001-00435 Rev. *E Page 9 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Application Example

R = 250ohms

Vt

R

R = 250ohms

Vt

Vt

R

Vt = Vddq/2

R = 50ohms

R

CC#

D
A

SRAM #4

R

P

S

#

W

P
S
#

B

W

S
#

K

ZQ

CQ/CQ#

Q

K#

CC#

D
A

K

SRAM #1

R
P
S
#

W

P
S
#

B

W

S
#

ZQ

CQ/CQ#

Q

K#

BUS

MASTER

(CPU

or

ASIC)

DATA IN

DATA OUT

Address

RPS#
WPS#
BWS#

Source K

Source K#

Delayed K

Delayed K#

CLKIN/CLKIN#

Notes

2. X = “Don't Care,” H = Logic HIGH, L = Logic LOW,

↑represents rising edge.

3. Device powers up deselected with the outputs in a tristate condition.

4. “A” represents address location latched by the devices when transaction was initiated. A + 1, A + 2, and A +3 represents the address sequence in the burst.

5. “t” represents the cycle at which a read/write operation is started. t + 1, t + 2, and t + 3 are the first, second and third clock cycles respectively succeeding the “t” clock cycle.

6. Data inputs are registered at K and K

rising edges. Data outputs are delivered on C and C rising edges, except when in single clock mode.

7. Ensure that when the clock is stopped K = K and C = C = HIGH. This is not essential, but permits most rapid restart by overcoming transmission line charging
symmetrically.

8. If this signal was LOW to initiate the previous cycle, this signal becomes a “Don’t Care” for this operation.

9. This signal was HIGH on previous K clock rise. Initiating consecutive read or write operations on consecutive K clock rises is not permitted. The device ignores the
second read or write request.

Figure 1 shows four QDR-II used in an application.

Figure 1. Application Example

Truth Table

[2, 3, 4, 5, 6, 7]

D = X
Q = High-Z

The truth table for CY7C1511KV18, CY7C1526KV18, CY7C1513KV18, and CY7C1515KV18 follows.

Operation K RPS WPS DQ DQ DQ DQ

Write Cycle:

L-H H

[8]L [9]

D(A) at K(t + 1)↑ D(A + 1) at K(t + 1)↑ D(A + 2) at K(t + 2)↑ D(A + 3) at K(t + 2)↑

Load address on the rising
edge of K; input write data
on two consecutive K and

rising edges.

K

Read Cycle:

L-H L

[9]

XQ(A) at C(t + 1)↑ Q(A + 1) at C(t + 2)↑ Q(A + 2) at C(t + 2)↑ Q(A + 3) at C(t + 3)↑

Load address on the rising
edge of K; wait one and a
half cycle; read data on
two consecutive C

and C

rising edges.

NOP: No Operation L-H H H D = X

Standby: Clock Stopped Stopped X X Previous State Previous State Previous State Previous State

Document Number: 001-00435 Rev. *E Page 10 of 31

Q = High-Z

D = X
Q = High-Z

D = X
Q = High-Z

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Write Cycle Descriptions

Note

10. Is based on a write cycle that was initiated in accordance with the Write Cycle Descriptions table. NWS

0

, NWS1, BWS0, BWS1, BWS2, and BWS3 can be altered on

different portions of a write cycle, as long as the setup and hold requirements are achieved.

The write cycle description table for CY7C1511KV18 and CY7C1513KV18 follows.

[2, 10]

BWS0/

NWS

0

BWS1/

NWS

K

1

K

Comments

L L L–H – During the data portion of a write sequence:

CY7C1511KV18 − both nibbles (D
CY7C1513KV18 − both bytes (D

) are written into the device.

[7:0]

) are written into the device.

[17:0]

L L – L-H During the data portion of a write sequence:

CY7C1511KV18 − both nibbles (D
CY7C1513KV18 − both bytes (D

) are written into the device.

[7:0]

) are written into the device.

[17:0]

L H L–H – During the data portion of a write sequence:

CY7C1511KV18 − only the lower nibble (D
CY7C1513KV18 − only the lower byte (D

) is written into the device, D

[3:0]

) is written into the device, D

[8:0]

L H – L–H During the data portion of a write sequence:

CY7C1511KV18 − only the lower nibble (D
CY7C1513KV18 − only the lower byte (D

) is written into the device, D

[3:0]

) is written into the device, D

[8:0]

H L L–H – During the data portion of a write sequence:

CY7C1511KV18 − only the upper nibble (D
CY7C1513KV18 − only the upper byte (D

) is written into the device, D

[7:4]

) is written into the device, D

[17:9]

H L – L–H During the data portion of a write sequence:

CY7C1511KV18 − only the upper nibble (D
CY7C1513KV18 − only the upper byte (D

) is written into the device, D

[7:4]

) is written into the device, D

[17:9]

H H L–H – No data is written into the devices during this portion of a write operation.

H H – L–H No data is written into the devices during this portion of a write operation.

Write Cycle Descriptions

The write cycle description table for CY7C1526KV18 follows.

[2, 10]

remains unaltered.

[7:4]

remains unaltered.

[17:9]

remains unaltered.

[7:4]

remains unaltered.

[17:9]

remains unaltered.

[3:0]

remains unaltered.

[8:0]

remains unaltered.

[3:0]

remains unaltered.

[8:0]

BWS

L L–H – During the data portion of a write sequence, the single byte (D

L – L–H During the data portion of a write sequence, the single byte (D

0

K K

[8:0]

[8:0]

H L–H – No data is written into the device during this portion of a write operation.

H – L–H No data is written into the device during this portion of a write operation.

) is written into the device.

) is written into the device.

Document Number: 001-00435 Rev. *E Page 11 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Write Cycle Descriptions

The write cycle description table for CY7C1515KV18 follows.

[2, 10]

BWS0BWS1BWS2BWS

LLLLL–H–During the data portion of a write sequence, all four bytes (D

LLLL–L–HDuring the data portion of a write sequence, all four bytes (D

K K Comments

3

the device.

the device.

) are written into

[35:0]

) are written into

[35:0]

L H H H L–H – During the data portion of a write sequence, only the lower byte (D

into the device. D

remains unaltered.

[35:9]

L H H H – L–H During the data portion of a write sequence, only the lower byte (D

into the device. D

H L H H L–H – During the data portion of a write sequence, only the byte (D

the device. D

[8:0]

H L H H – L–H During the data portion of a write sequence, only the byte (D

the device. D

[8:0]

H H L H L–H – During the data portion of a write sequence, only the byte (D

the device. D

[17:0]

H H L H – L–H During the data portion of a write sequence, only the byte (D

the device. D

[17:0]

H H H L L–H – During the data portion of a write sequence, only the byte (D

the device. D

[26:0]

H H H L – L–H During the data portion of a write sequence, only the byte (D

the device. D

[26:0]

remains unaltered.

[35:9]

and D

and D

and D

and D

remains unaltered.

[35:18]

remains unaltered.

[35:18]

remains unaltered.

[35:27]

remains unaltered.

[35:27]

remains unaltered.

remains unaltered.

) is written into

[17:9]

) is written into

[17:9]

) is written into

[26:18]

) is written into

[26:18]

) is written into

[35:27]

) is written into

[35:27]

HHHHL–H–No data is written into the device during this portion of a write operation.

) is written

[8:0]

) is written

[8:0]

HHHH–L–HNo data is written into the device during this portion of a write operation.

Document Number: 001-00435 Rev. *E Page 12 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

IEEE 1149.1 Serial Boundary Scan (JTAG)

These SRAMs incorporate a serial boundary scan Test Access
Port (TAP) in the FBGA package. This part is fully compliant with
IEEE Standard #1149.1-2001. The TAP operates using JEDEC
standard 1.8V IO logic levels.

Disabling the JTAG Feature

It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are inter­nally pulled up and may be unconnected. They may alternatively
be connected to V
unconnected. Upon power up, the device comes up in a reset
state, which does not interfere with the operation of the device.

Test Access Port—Test Clock

The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.

Test Mode Select (TMS)

The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. This pin may be left
unconnected if the TAP is not used. The pin is pulled up inter­nally, resulting in a logic HIGH level.

Test Data-In ( TDI)

The TDI pin is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information about
loading the instruction register, see the TAP Controller State

Diagram on page 15. TDI is internally pulled up and can be

unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) on any register.

Test Data-Out (TDO)

The TDO output pin is used to serially clock data out from the
registers. The output is active, depending upon the current state
of the TAP state machine (see Instruction Codes on page 18).
The output changes on the falling edge of TCK. TDO is
connected to the least significant bit (LSB) of any register.

Performing a TAP Reset

A Reset is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This Reset does not affect the operation of the
SRAM and can be performed when the SRAM is operating. At
power up, the TAP is reset internally to ensure that TDO comes
up in a high-Z state.

TAP Registers

Registers are connected between the TDI and TDO pins to scan
the data in and out of the SRAM test circuitry. Only one register
can be selected at a time through the instruction registers. Data
is serially loaded into the TDI pin on the rising edge of TCK. Data
is output on the TDO pin on the falling edge of TCK.

through a pull up resistor. TDO must be left

DD

Instruction Register

Three-bit instructions are serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO pins, as shown in TAP Controller Block Diagram on
page 16. Upon power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state, as described
in the previous section.

When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary “01” pattern to allow for
fault isolation of the board level serial test path.

Bypass Register

To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that is placed between TDI and
TDO pins. This enables shifting of data through the SRAM with
minimal delay. The bypass register is set LOW (V
BYPASS instruction is executed.

Boundary Scan Register

The boundary scan register is connected to all of the input and
output pins on the SRAM. Several No Connect (NC) pins are also
included in the scan register to reserve pins for higher density
devices.

The boundary scan register is loaded with the contents of the
RAM input and output ring when the TAP controller is in the
Capture-DR state and is then placed between the TDI and TDO
pins when the controller is moved to the Shift-DR state. The
EXTEST, SAMPLE/PRELOAD, and SAMPLE Z instructions are
used to capture the contents of the input and output ring.

The Boundary Scan Order on page 19 shows the order in which
the bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected to
TDI, and the LSB is connected to TDO.

Identification (ID) Register

The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in Identification Register Definitions on
page 18.

) when the

SS

TAP Instruction Set

Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in Instruction

Codes on page 18. Three of these instructions are listed as

RESERVED and must not be used. The other five instructions
are described in this section in detail.

Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO pins. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.

Document Number: 001-00435 Rev. *E Page 13 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

IDCODE

The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO pins and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state. The
IDCODE instruction is loaded into the instruction register at
power up or whenever the TAP controller is supplied a
Test-Logic-Reset state.

SAMPLE Z

The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. The SAMPLE Z command puts the output bus
into a High-Z state until the next command is supplied during the
Update IR state.

SAMPLE/PRELOAD

SAMPLE/PRELOAD is a 1149.1 mandatory instruction. When
the SAMPLE/PRELOAD instructions are loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the input and output pins is captured
in the boundary scan register.

The TAP controller clock can only operate at a frequency up to
20 MHz, while the SRAM clock operates more than an order of
magnitude faster. Because there is a large difference in the clock
frequencies, it is possible that during the Capture-DR state, an
input or output undergoes a transition. The TAP may then try to
capture a signal while in transition (metastable state). This does
not harm the device, but there is no guarantee as to the value
that is captured. Repeatable results may not be possible.

To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller's capture setup plus hold
times (t
correctly if there is no way in a design to stop (or slow) the clock
during a SAMPLE/PRELOAD instruction. If this is an issue, it is
still possible to capture all other signals and simply ignore the
value of the CK and CK captured in the boundary scan register.

After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO pins.

and tCH). The SRAM clock input might not be captured

CS

PRELOAD places an initial data pattern at the latched parallel
outputs of the boundary scan register cells before the selection
of another boundary scan test operation.

The shifting of data for the SAMPLE and PRELOAD phases can
occur concurrently when required, that is, while the data
captured is shifted out, the preloaded data can be shifted in.

BYPASS

When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO pins. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.

EXTEST

The EXTEST instruction drives the preloaded data out through
the system output pins. This instruction also connects the
boundary scan register for serial access between the TDI and
TDO in the Shift-DR controller state.

EXTEST OUTPUT BUS TRISTATE

IEEE Standard 1149.1 mandates that the TAP controller be able
to put the output bus into a tristate mode.

The boundary scan register has a special bit located at bit #108.
When this scan cell, called the “extest output bus tristate,” is
latched into the preload register during the Update-DR state in
the TAP controller, it directly controls the state of the output
(Q-bus) pins, when the EXTEST is entered as the current
instruction. When HIGH, it enables the output buffers to drive the
output bus. When LOW, this bit places the output bus into a
High-Z condition.

This bit is set by entering the SAMPLE/PRELOAD or EXTEST
command, and then shifting the desired bit into that cell, during
the Shift-DR state. During Update-DR, the value loaded into that
shift-register cell latches into the preload register. When the
EXTEST instruction is entered, this bit directly controls the output
Q-bus pins. Note that this bit is preset HIGH to enable the output
when the device is powered up, and also when the TAP controller
is in the Test-Logic-Reset state.

Reserved

These instructions are not implemented but are reserved for
future use. Do not use these instructions.

Document Number: 001-00435 Rev. *E Page 14 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

TAP Controller State Diagram

TEST-LOGIC
RESET

TEST-LOGIC/
IDLE

SELECT
DR-SCAN

CAPTURE-DR

SHIFT-DR

EXIT1-DR

PAUSE-DR

EXIT2-DR

UPDATE-DR

1

0

1

1

0

1

0

1

0

0

0

1

1

1

0

1

0

1

0

0

0

1

0

1

1

0

1

0

0

1

1

0

SELECT
IR-SCAN

CAPTURE-IR

SHIFT-IR

EXIT1-IR

PAU SE-IR

EXIT2-IR

UPDATE-IR

Note

11. The 0/1 next to each state represents the value at TMS at the rising edge of TCK.

The state diagram for the TAP controller follows.

[11]

Document Number: 001-00435 Rev. *E Page 15 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

TAP Controller Block Diagram

0

012..29

3031

Boundary Scan Register

Identification Register

012..

.

.108

012

Instruction Register

Bypass Register

Selection
Circuitry

Selection
Circuitry

TAP Controller

TDI

TDO

TCK

TMS

Notes

12. These characteristics pertain to the TAP inputs (TMS, TCK, TDI and TDO). Parallel load levels are specified in the Electrical Characteristics Table.

13. Overshoot: V

IH

(AC) < V

DDQ

+ 0.85V (Pulse width less than t

CYC

/2), Undershoot: V

IL

(AC) > −1.5V (Pulse width less than t

CYC

/2).

14. All voltage referenced to Ground.

TAP Electrical Characteristics

Over the Operating Range

Parameter Description Test Conditions Min Max Unit

V

OH1

V

OH2

V

OL1

V

OL2

V

IH

V

IL

I

X

Output HIGH Voltage I

Output HIGH Voltage I

Output LOW Voltage IOL = 2.0 mA 0.4 V

Output LOW Voltage IOL = 100 μA0.2V

Input HIGH Voltage 0.65VDDV

Input LOW Voltage –0.3 0.35V

Input and Output Load Current GND ≤ VI ≤ V

[12, 13, 14]

= −2.0 mA 1.4 V

OH

= −100 μA1.6 V

OH

DD

–5 5 μA

+ 0.3 V

DD

DD

V

Document Number: 001-00435 Rev. *E Page 16 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

TAP AC Switching Characteristics

t

TL

t

TH

(a)

TDO

C

L

= 20 pF

Z

0

= 50

Ω

GND

0.9V

50

Ω

1.8V

0V

ALL INPUT PULSES

0.9V

Test Clock

Test Mode Select

TCK

TMS

Test Data In
TDI

Test Data Out

t

TCYC

t

TMSH

t

TMSS

t

TDIS

t

TDIH

t

TDOV

t

TDOX

TDO

Notes

15. t

CS

and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.

16. Test conditions are specified using the load in TAP AC Test Conditions. t

R/tF

= 1 ns.

Over the Operating Range

Parameter Description Min Max Unit

t

TCYC

t

TF

t

TH

t

TL

TCK Clock Cycle Time 50 ns

TCK Clock Frequency 20 MHz

TCK Clock HIGH 20 ns

TCK Clock LOW 20 ns

Setup Times

t

TMSS

t

TDIS

t

CS

TMS Setup to TCK Clock Rise 5 ns

TDI Setup to TCK Clock Rise 5 ns

Capture Setup to TCK Rise 5 ns

Hold Times

t

TMSH

t

TDIH

t

CH

TMS Hold after TCK Clock Rise 5 ns

TDI Hold after Clock Rise 5 ns

Capture Hold after Clock Rise 5 ns

Output Times

t

TDOV

t

TDOX

TCK Clock LOW to TDO Valid 10 ns

TCK Clock LOW to TDO Invalid 0 ns

[15, 16]

TAP Timing and Test Conditions

Figure 2 shows the TAP timing and test conditions.

Figure 2. TAP Timing and Test Conditions

[16]

Document Number: 001-00435 Rev. *E Page 17 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Identification Register Definitions

Instruction Field

Revision Number
(31:29)

Cypress Device ID
(28:12)

Cypress JEDEC ID
(11:1)

ID Register
Presence (0)

CY7C1511KV18 CY7C1526KV18 CY7C1513KV18 CY7C1515KV18

000 000 000 000 Version number.

11010011011000100 11010011011001100 11010011011010100 11010011011100100 Defines the type of

00000110100 00000110100 00000110100 00000110100 Allows unique

1111Indicates the

Value

Description

SRAM.

identification of
SRAM vendor.

presence of an ID
register.

Scan Register Sizes

Register Name Bit Size

Instruction 3

Bypass 1

ID 32

Boundary Scan 109

Instruction Codes

Instruction Code Description

EXTEST 000 Captures the input and output ring contents.

IDCODE 001 Loads the ID register with the vendor ID code and places the register between TDI and TDO.

This operation does not affect SRAM operation.

SAMPLE Z 010 Captures the input and output contents. Places the boundary scan register between TDI and

TDO. Forces all SRAM output drivers to a High-Z state.

RESERVED 011 Do Not Use: This instruction is reserved for future use.

SAMPLE/PRELOAD 100 Captures the input and output ring contents. Places the boundary scan register between TDI

RESERVED 101 Do Not Use: This instruction is reserved for future use.

RESERVED 110 Do Not Use: This instruction is reserved for future use.

BYPASS 111 Places the bypass register between TDI and TDO. This operation does not affect SRAM

and TDO. Does not affect the SRAM operation.

operation.

Document Number: 001-00435 Rev. *E Page 18 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Boundary Scan Order

Bit # Bump ID Bit # Bump ID Bit # Bump ID Bit # Bump ID

0 6R 28 10G 56 6A 84 1J

16P299G575B852J

2 6N 30 11F 58 5A 86 3K

3 7P 31 11G 59 4A 87 3J

47N329F605C882K

5 7R 33 10F 61 4B 89 1K

6 8R 34 11E 62 3A 90 2L

7 8P 35 10E 63 2A 91 3L

8 9R 36 10D 64 1A 92 1M

9 11P 37 9E 65 2B 93 1L

10 10P 38 10C 66 3B 94 3N

11 10N 39 11D 67 1C 95 3M

12 9P 40 9C 68 1B 96 1N

13 10M 41 9D 69 3D 97 2M

14 11N 42 11B 70 3C 98 3P

15 9M 43 11C 71 1D 99 2N

16 9N 44 9B 72 2C 100 2P

17 11L 45 10B 73 3E 101 1P

18 11M 46 11A 74 2D 102 3R

19 9L 47 10A 75 2E 103 4R

20 10L 48 9A 76 1E 104 4P

21 11K 49 8B 77 2F 105 5P

22 10K 50 7C 78 3F 106 5N

23 9J 51 6C 79 1G 107 5R

24 9K 52 8A 80 1F 108 Internal

25 10J 53 7A 81 3G

26 11J 54 7B 82 2G

27 11H 55 6B 83 1H

Document Number: 001-00435 Rev. *E Page 19 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Power Up Sequence in QDR-II SRAM

~

~

QDR-II SRAMs must be powered up and initialized in a
predefined manner to prevent undefined operations.

Power Up Sequence

■ Apply power and drive DOFF either HIGH or LOW (All other

inputs can be HIGH or LOW).

❐ Apply V
❐ Apply V
❐ Drive DOFF HIGH.

■ Provide stable DOFF (HIGH), power and clock (K, K) for 20 μs

to lock the PLL.

before V

DD

DDQ

K

before V

.

DDQ

or at the same time as V

REF

.

REF

Figure 3. Power Up Waveforms

PLL Constraints

■ PLL uses K clock as its synchronizing input. The input must

have low phase jitter, which is specified as t

■ The PLL functions at frequencies down to 120 MHz.

■ If the input clock is unstable and the PLL is enabled, then the

PLL may lock onto an incorrect frequency, causing unstable
SRAM behavior. To avoid this, provide 20 μs of stable clock to
relock to the desired clock frequency.

~

KC Var

.

K

~

Unstable Clock

> 20Ps Stable clock

Start Normal
Operation

/

Clock Start

/

V

V

DDQDD

(Clock Starts after Stable)

/

V

V

DDQDD

DOFF

V

V

DD

DDQ

Stable (< +/- 0.1V DC per 50ns )

Fix HIGH (or tie to V

DDQ

)

Document Number: 001-00435 Rev. *E Page 20 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Maximum Ratings

Notes

17. Power up: Assumes a linear ramp from 0V to V

DD

(min) within 200 ms. During this time V

IH

< V

DD

and V

DDQ

< VDD.

18. Output are impedance controlled. I

OH

= −(V

DDQ

/2)/(RQ/5) for values of 175 ohms <= RQ <= 350 ohms.

19. Output are impedance controlled. I

OL

= (V

DDQ

/2)/(RQ/5) for values of 175 ohms <= RQ <= 350 ohms.

20. V

REF

(min) = 0.68V or 0.46V

DDQ

, whichever is larger, V

REF

(max) = 0.95V or 0.54V

DDQ

, whichever is smaller.

21. The operation current is calculated with 50% read cycle and 50% write cycle.

Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.

Storage Temperature ................................. –65°C to +150°C

Ambient Temperature with Power Applied.. –55°C to +125°C

Supply Voltage on VDD Relative to GND ........–0.5V to +2.9V

Supply Voltage on V

DC Applied to Outputs in High-Z ........ –0.5V to V

DC Input Voltage

Relative to GND.......–0.5V to +V

DDQ

[13]

..............................–0.5V to VDD + 0.3V

DDQ

DD

+ 0.3V

Electrical Characteristics

Current into Outputs (LOW) ........................................ 20 mA

Static Discharge Voltage (MIL-STD-883, M. 3015).. > 2001V

Latch up Current.................................................... > 200 mA

Operating Range

Range

Temperature (TA) V

Commercial 0°C to +70°C 1.8 ± 0.1V 1.4V to

Industrial –40°C to +85°C

Ambient

DD

[17]

V

DDQ

V

DD

[17]

DC Electrical Characteristics

Over the Operating Range

[14]

Parameter Description Test Conditions Min Typ Max Unit

V

DD

V

DDQ

V

OH

V

OL

V

OH(LOW)

V

OL(LOW)

V

IH

V

IL

I

X

I

OZ

V

REF

[21]

I

DD

Power Supply Voltage 1.7 1.8 1.9 V

IO Supply Voltage 1.4 1.5 V

Output HIGH Voltage Note 18 V

Output LOW Voltage Note 19 V

Output HIGH Voltage I

= −0.1 mA, Nominal Impedance V

OH

Output LOW Voltage IOL = 0.1 mA, Nominal Impedance V

Input HIGH Voltage V

/2 – 0.12 V

DDQ

/2 – 0.12 V

DDQ

– 0.2 V

DDQ

SS

+ 0.1 V

REF

Input LOW Voltage –0.3 V
Input Leakage Current GND ≤ VI ≤ V
Output Leakage Current GND ≤ VI ≤ V

Input Reference Voltage

VDD Operating Supply V

[20]

Typical Value = 0.75V 0.68 0.75 0.95 V

= Max,

DD

= 0 mA,

I

OUT

f = f

MAX

= 1/t

DDQ

Output Disabled −5 5 μA

DDQ,

333 MHz (x8) 600 mA

CYC

(x9) 600

−5 5 μA

DD

/2 + 0.12 V

DDQ

/2 + 0.12 V

DDQ

DDQ

0.2 V

+ 0.3 V

DDQ

– 0.1 V

REF

(x18) 620

(x36) 850

300 MHz (x8) 560 mA

(x9) 560

(x18) 570

(x36) 790

250 MHz (x8) 490 mA

(x9) 490

(x18) 500

(x36) 680

V

V

Document Number: 001-00435 Rev. *E Page 21 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Electrical Characteristics (continued)

DC Electrical Characteristics

Over the Operating Range

[14]

Parameter Description Test Conditions Min Typ Max Unit

[21]

I

DD

VDD Operating Supply V

DD

I

OUT

f = f

= Max,

= 0 mA,

= 1/t

MAX

CYC

200 MHz (x8) 430 mA

(x9) 430

(x18) 440

(x36) 580

167 MHz (x8) 380 mA

(x9) 380

(x18) 390

(x36) 510

I

SB1

Automatic Power Down
Current

Max VDD,
Both Ports Deselected,
VIN ≥ VIH or VIN ≤ VIL
f = f
Inputs Static

MAX

= 1/t

CYC,

333 MHz (x8) 290 mA

(x9) 290

(x18) 290

(x36) 290

300 MHz (x8) 280 mA

(x9) 280

(x18) 280

(x36) 280

250 MHz (x8) 270 mA

(x9) 270

(x18) 270

(x36) 270

200 MHz (x8) 250 mA

(x9) 250

(x18) 250

(x36) 250

167 MHz (x8) 250 mA

(x9) 250

(x18) 250

(x36) 250

AC Electrical Characteristics

Over the Operating Range

Parameter Description Test Conditions Min Typ Max Unit

V

IH

V

IL

Input HIGH Voltage V

Input LOW Voltage – – V

Document Number: 001-00435 Rev. *E Page 22 of 31

[13]

+ 0.2 – – V

REF

– 0.2 V

REF

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Capacitance

1.25V

0.25V

R = 50Ω

5pF

INCLUDING

JIG AND

SCOPE

ALL INPUT PULSES

Device

R

L

= 50Ω

Z

0

= 50Ω

V

REF

= 0.75V

V

REF

= 0.75V

[22]

0.75V

Under
Te st

0.75V

Device
Under
Te st

OUTPUT

0.75V

V

REF

V

REF

OUTPUT

ZQ

ZQ

(a)

Slew Rate = 2 V/ns

RQ =
250

Ω

(b)

RQ =
250

Ω

Note

22. Unless otherwise noted, test conditions are based on signal transition time of 2V/ns, timing reference levels of 0.75V, Vref = 0.75V, RQ = 250Ω, V

DDQ

= 1.5V, input

pulse levels of 0.25V to 1.25V, and output loading of the specified I

OL/IOH

and load capacitance shown in (a) of AC Test Loads and Waveforms.

Tested initially and after any design or process change that may affect these parameters.

Parameter Description Test Conditions Max Unit

C

Input Capacitance TA = 25°C, f = 1 MHz, VDD = 1.8V, V

IN

C

O

Output Capacitance 3pF

= 1.5V 2 pF

DDQ

Thermal Resistance

Tested initially and after any design or process change that may affect these parameters.

Parameter Description Test Conditions

Θ

JA

Θ

JC

Thermal Resistance
(Junction to Ambient)

Thermal Resistance
(Junction to Case)

Test conditions follow standard test methods and
procedures for measuring thermal impedance, in
accordance with EIA/JESD51.

Figure 4. AC Test Loads and Waveforms

165 FBGA

Package

13.7 °C/W

3.73 °C/W

Unit

Document Number: 001-00435 Rev. *E Page 23 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Switching Characteristics

Notes

23. When a part with a maximum frequency above 167 MHz is operating at a lower clock frequency, it requires the input timings of the frequency range in which it is operated
and outputs data with the output timings of that frequency range.

24. This part has a voltage regulator internally; t

POWER

is the time that the power must be supplied above VDD minimum initially before a read or write operation is initiated.

Over the Operating Range

[22, 23]

Cypress

Parameter

t

POWER

t

CYC

t

KH

t

KL

t

KHKH

t

KHCH

t

t

t

t

t

Setup Times

t

SA

t

SC

t

SCDDR

t

SD

t

t

t

t

Hold Times

t

t

HA

HC

t

t

Consortium

Parameter

KHKH

KHKL

KLKH

KHKH

KHCH

AVKH

IVKH

IVKH

DVKH

KHAX

KHIX

Description

Unit

Min Max Min Max Min Max Min Max Min Max

333 MHz 300 MHz 250 MHz 200 MHz 167 MHz

VDD(Typical) to the First Access

[24]

11111ms

K Clock and C Clock Cycle Time 3.0 8.4 3.3 8.4 4.0 8.4 5.0 8.4 6.0 8.4 ns

Input Clock (K/K; C/C) HIGH

Input Clock (K/K; C/C) LOW

K Clock Rise to K Clock Rise and C
to C

Rise (rising edge to rising edge)

K/K Clock Rise to C/C Clock Rise

1.20 – 1.32 – 1.6 – 2.0 – 2.4 – ns

1.20 – 1.32 – 1.6 – 2.0 – 2.4 – ns

1.35 – 1.49 – 1.8 – 2.2 – 2.7 – ns

01.3001.4501.802.202.7ns

(rising edge to rising edge)

Address Setup to K Clock Rise 0.4 – 0.4 – 0.5 – 0.6 – 0.7 – ns

Control Setup to K Clock Rise

, WPS)

(RPS

Double Data Rate Control Setup to
Clock (K/K
(BWS

D

[X:0]

) Rise

, BWS1, BWS2, BWS3)

0

Setup to Clock (K/K) Rise

Address Hold after K Clock Rise

Control Hold after K Clock Rise

, WPS)

(RPS

0.4 – 0.4 – 0.5 – 0.6 – 0.7 – ns

0.3 – 0.3 – 0.35 – 0.4 – 0.5 – ns

0.3 – 0.3 – 0.35 – 0.4 – 0.5 – ns

0.4 – 0.4 – 0.5 – 0.6 – 0.7 – ns

0.4 – 0.4 – 0.5 – 0.6 – 0.7 – ns

t

HCDDR

t

HD

Document Number: 001-00435 Rev. *E Page 24 of 31

t

KHIX

t

KHDX

Double Data Rate Control Hold after
Clock (K/K
(BWS

D

[X:0]

) Rise

, BWS1, BWS2, BWS3)

0

Hold after Clock (K/K) Rise

0.3 – 0.3 – 0.35 – 0.4 – 0.5 – ns

0.3 – 0.3 – 0.35 – 0.4 – 0.5 – ns

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Switching Characteristics (continued)

Notes

25. These parameters are extrapolated from the input timing parameters (t

CYC

/2 - 250 ps, where 250 ps is the internal jitter). These parameters are only guaranteed by

design and are not tested in production

26. t

CHZ

, t

CLZ

, are specified with a load capacitance of 5 pF as in (b) of AC Test Loads and Waveforms. Transition is measured ± 100 mV from steady-state voltage.

27. At any voltage and temperature t

CHZ

is less than t

CLZ

and t

CHZ

less than tCO.

Over the Operating Range

[22, 23]

Cypress

Parameter

Consortium

Parameter

Output Times

t

CO

t

DOH

t

CCQO

t

CQOH

t

CQD

t

CQDOHtCQHQX

t

CQH

t

CQHCQHtCQHCQH

t

CHZ

t

CLZ

t

CHQV

t

CHQX

t

CHCQV

t

CHCQX

t

CQHQV

t

CQHCQL

t

CHQZ

t

CHQX1

PLL Timing

t

KC Var

t

KC lock

t

KC ResettKC Reset

t

KC Var

t

KC lock

Description

Unit

Min Max Min Max Min Max Min Max Min Max

333 MHz 300 MHz 250 MHz 200 MHz 167 MHz

C/C Clock Rise (or K/K in single

– 0.45 – 0.45 – 0.45 – 0.45 – 0.50 ns

clock mode) to Data Valid

Data Output Hold after Output C/C

–0.45 – –0.45 – –0.45 – –0.45 – –0.50 – ns

Clock Rise (Active to Active)

C/C Clock Rise to Echo Clock Valid

Echo Clock Hold after C/C Clock

– 0.45 – 0.45 – 0.45 – 0.45 – 0.50 ns

–0.45 – –0.45 – –0.45 – –0.45 – –0.50 – ns

Rise

Echo Clock High to Data Valid 0.25 0.27 0.30 0.35 0.40 ns

Echo Clock High to Data Invalid –0.25 – –0.27 – –0.30 – –0.35 – –0.40 – ns

Output Clock (CQ/CQ) HIGH

CQ Clock Rise to CQ Clock Rise
(rising edge to rising edge)

Clock (C/C) Rise to High-Z
(Active to High-Z)

[26, 27]

Clock (C/C) Rise to Low-Z

[25]

[25]

[26, 27]

1.25 – 1.4 – 1.75 – 2.25 – 2.75 – ns

1.25 – 1.4 – 1.75 – 2.25 – 2.75 – ns

– 0.45 – 0.45 – 0.45 – 0.45 – 0.50 ns

–0.45 – –0.45 – –0.45 – –0.45 – –0.50 – ns

Clock Phase Jitter – 0.20 – 0.20 – 0.20 – 0.20 – 0.20 ns

PLL Lock Time (K, C) 20–20–20–20–20– μs

K Static to PLL Reset 30 30 30 30 30 ns

Document Number: 001-00435 Rev. *E Page 25 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Switching Waveforms

Notes

28. Q00 refers to output from address A0. Q01 refers to output from the next internal burst address following A0, that is, A0+1.

29. Outputs are disabled (High-Z) one clock cycle after a NOP.

30. In this example, if address A2 = A1, then data Q20 = D10, Q21 = D11, Q22 = D12, and Q23 = D13. Write data is forwarded immediately as read results. This note
applies to the whole diagram.

Figure 5. Read/Write/Deselect Sequence

[28, 29, 30]

RPS

WPS

NOP

1

READ

2

READWRITE WRITE

345

NOP

6

7

K

t

KH

t

KL

t

CYC

t

KHKH

K

t

t

A

t

D

Q

t

KHCH

HC

SC

A0 A1

t

SA

HA

t

KHCH

t

CLZ

tt

A2

t

HD

t

SD

D10 D11

Q00

Q01 Q02

t

CO

t

DOH

A3

t

SD

D12

HCSC

t

HD

Q03

t

CQDOH

D30 D31

Q20

Q21

t

CQD

D32

Q22

t

D33

Q23

CHZ

D13

C

t

CYC

t

KHKH

t

KH

t

KL

C

t

CCQO

t

CCQO

CQ

t

CQH

t

CQHCQH

t

CQOH

t

CQOH

CQ

DON’T CARE UNDEFINED

Document Number: 001-00435 Rev. *E Page 26 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Ordering Information

The following table lists all possible speed, package, and temperature range options supported for these devices. Note that some
options listed may not be available for order entry. To verify the availability of a specific option, visit the Cypress website at

www.cypress.com and refer to the product summary page at http://www.cypress.com/products or contact your local sales

representative for the status of availability of parts.

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office
closest to you, visit us at http://app.cypress.com/portal/server.pt?space=CommunityPage&control=SetCommunity&CommunityID=

201&PageID=230.

Table 2. Ordering Information

Speed

(MHz) Ordering Code

333 CY7C1511KV18-333BZC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Commercial

CY7C1526KV18-333BZC

CY7C1513KV18-333BZC

CY7C1515KV18-333BZC

CY7C1511KV18-333BZXC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-333BZXC

CY7C1513KV18-333BZXC

CY7C1515KV18-333BZXC

CY7C1511KV18-333BZI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Industrial

CY7C1526KV18-333BZI

CY7C1513KV18-333BZI

CY7C1515KV18-333BZI

CY7C1511KV18-333BZXI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-333BZXI

CY7C1513KV18-333BZXI

CY7C1515KV18-333BZXI

300 CY7C1511KV18-300BZC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Commercial

CY7C1526KV18-300BZC

CY7C1513KV18-300BZC

CY7C1515KV18-300BZC

CY7C1511KV18-300BZXC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-300BZXC

CY7C1513KV18-300BZXC

CY7C1515KV18-300BZXC

CY7C1511KV18-300BZI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Industrial

CY7C1526KV18-300BZI

CY7C1513KV18-300BZI

CY7C1515KV18-300BZI

CY7C1511KV18-300BZXI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-300BZXI

CY7C1513KV18-300BZXI

CY7C1515KV18-300BZXI

Package
Diagram Package Type

Operating

Range

Document Number: 001-00435 Rev. *E Page 27 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Table 2. Ordering Information (continued)

Speed

(MHz) Ordering Code

250 CY7C1511KV18-250BZC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Commercial

CY7C1526KV18-250BZC

CY7C1513KV18-250BZC

CY7C1515KV18-250BZC

CY7C1511KV18-250BZXC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-250BZXC

CY7C1513KV18-250BZXC

CY7C1515KV18-250BZXC

CY7C1511KV18-250BZI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Industrial

CY7C1526KV18-250BZI

CY7C1513KV18-250BZI

CY7C1515KV18-250BZI

CY7C1511KV18-250BZXI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-250BZXI

CY7C1513KV18-250BZXI

CY7C1515KV18-250BZXI

200 CY7C1511KV18-200BZC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Commercial

CY7C1526KV18-200BZC

CY7C1513KV18-200BZC

CY7C1515KV18-200BZC

CY7C1511KV18-200BZXC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-200BZXC

CY7C1513KV18-200BZXC

CY7C1515KV18-200BZXC

CY7C1511KV18-200BZI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Industrial

CY7C1526KV18-200BZI

CY7C1513KV18-200BZI

CY7C1515KV18-200BZI

CY7C1511KV18-200BZXI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-200BZXI

CY7C1513KV18-200BZXI

CY7C1515KV18-200BZXI

Package
Diagram Package Type

Operating

Range

Document Number: 001-00435 Rev. *E Page 28 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Table 2. Ordering Information (continued)

Speed

(MHz) Ordering Code

167 CY7C1511KV18-167BZC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Commercial

CY7C1526KV18-167BZC

CY7C1513KV18-167BZC

CY7C1515KV18-167BZC

CY7C1511KV18-167BZXC 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-167BZXC

CY7C1513KV18-167BZXC

CY7C1515KV18-167BZXC

CY7C1511KV18-167BZI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Industrial

CY7C1526KV18-167BZI

CY7C1513KV18-167BZI

CY7C1515KV18-167BZI

CY7C1511KV18-167BZXI 51-85180 165-Ball Fine Pitch Ball Grid Array (13 x 15 x 1.4 mm) Pb-Free

CY7C1526KV18-167BZXI

CY7C1513KV18-167BZXI

CY7C1515KV18-167BZXI

Package
Diagram Package Type

Operating

Range

Document Number: 001-00435 Rev. *E Page 29 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Package Diagram

A

1

PIN 1 CORNER

15.00±0.10

13.00±0.10

7.00

1.00

Ø0.50 (165X)

Ø0.25MCAB

Ø0.05 M C

B

A

0.15(4X)

0.35±0.06

SEATING PLANE

0.53±0.05

0.25 C

0.15 C

PIN 1 CORNER

TOP VIEW

BOTTOM VIEW

2345678910

10.00

14.00

B

C

D

E

F

G

H

J

K

L

M

N

11

1110986754321

P

R

P

R

K

M

N

L

J

H

G

F

E

D

C

B

A

A

15.00±0.10

13.00±0.10

B

C

1.00

5.00

0.36

-0.06
+0.14

1.40 MAX.

SOLDER PAD TYPE : NON-SOLDER MASK DEFINED (NSMD)

NOTES :

PACKAGE WEIGHT : 0.475g

JEDEC REFERENCE : MO-216 / DESIGN 4.6C

PACKAGE CODE : BB0AC

51-85180-*A

Figure 6. 165-Ball FBGA (13 x 15 x 1.4 mm), 51-85180

Document Number: 001-00435 Rev. *E Page 30 of 31

[+] Feedback

CY7C1511KV18, CY7C1526KV18

CY7C1513KV18, CY7C1515KV18

Document History Page

Document Title: CY7C1511KV18/CY7C1526KV18/CY7C1513KV18/CY7C1515KV18, 72-Mbit QDR™-II SRAM 4-Word
Burst Architecture
Document Number: 001-00435

Rev. ECN No.

Orig. of
Change

Submission

Date

Description of change

** 374703 SYT See ECN New Data Sheet

*A 1103823 NXR See ECN Updated I

Updated ordering information table

DD

spec

*B 1699083 VKN/AESA See ECN Converted from Advance Information to Preliminary
*C 2148307 VKN/AESA See ECN Changed PLL lock time from 1024 cycles to 20 μs

Added footnote #21 related to I
Corrected typo in the footnote #25

DD

*D 2606839 VKN/PYRS 11/13/08 Changed JTAG ID [31:29] from 001 to 000,

Updated power up sequence waveform and its description,
Changed Ambient Temperature with Power Applied from “–10°C to +85°C” to
“–55°C to +125°C” in the “Maximum Ratings” on page 21,
Included Thermal Resistance values,
Changed the package size from 15 x 17 x 1.4 mm to 13 x 15 x 1.4 mm.

*E 2681899 VKN/PYRS 04/01/2009 Converted from preliminary to final

Added note on top of the Ordering Information table
Moved to external web

Sales, Solutions, and Legal Information

Worldwide Sales and Design Support

Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.

Products

PSoC psoc.cypress.com

Clocks & Buffers clocks.cypress.com

Wireless wireless.cypress.com

Memories memory.cypress.com

Image Sensors image.cypress.com

PSoC Solutions

General psoc.cypress.com/solutions

Low Power/Low Voltage psoc.cypress.com/low-power

Precision Analog psoc.cypress.com/precision-analog

LCD Drive psoc.cypress.com/lcd-drive

CAN 2.0b psoc.cypress.com/can

USB psoc.cypress.com/usb

© Cypress Semiconductor Corporation, 2005-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used
for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use
as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.

Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.

Use may be limited by and subject to the applicable Cypress software license agreement.

Document Number: 001-00435 Rev. *E Revised March 30, 2009 Page 31 of 31

QDR RAMs and Quad Data Rate RAMs comprise a new family of products developed by Cypress, IDT, NEC, Renesas, and Samsung. All product and company names mentioned in this document
are the trademarks of thei r respective holders.

[+] Feedback