CY8CKIT-046 QUICK START GUIDE
PSOC® 4 L-SERIES PIONEER KIT
Kit Contents:
®
1 PSoC
2 USB Standard-A to Mini-B cable
3 Four jumper wires (4 inches each)
4 Two proximity sensor wires
(5 inches each)
5 Stereo audio earphone with microphone
6 Quick Start Guide (this document)
4 L-Series Pioneer board
www.cypress.com/CY8CKIT-046
• Connect the board to your PC using the provided
USB cable through PSoC 4200L USB connector J11
21
• The board will enumerate as a USB composite
device (HID mouse and keyboard)
• Wait for the driver installation to complete. Blue
LED turns on indicating successful driver installation
CY8CKIT-046 QUICK START GUIDE
43
• Control the mouse pointer and buttons using the
CapSense® Gesture Pad (operating as a joystick)
Note:
Refer to USB Mouse example in the Kit Guide
for details on various gestures supported by the
CapSense Gesture Pad (joystick)
Supported actions
Left-click Right-click Mouse pointer (joystick) control
Additional Learning Resources
PSoC Creator:
www.cypress.com/PSoCCreator
AN79953 – Getting Started with PSoC 4:
www.cypress.com/AN79953
AN73854 – PSoC 3, PSoC 4, and
PSoC 5LP Introduction to Bootloaders:
www.cypress.com/AN73854
• Download and install the PSoC CreatorTM IDE,
PSoC 4 L-Series Pioneer Kit code examples,
documents and hardware design les from
www.cypress.com/CY8CKIT-046
AN84858 – PSoC 4 and PSoC Analog Coprocessor
Programming Using an External Microcontroller (HSSP):
www.cypress.com/AN84858
AN85951 – PSoC 4 and PSoC 6 MCU
CapSense Design Guide
www.cypress.com/AN85951
PSoC Code Examples:
www.cypress.com/CodeExamples
NC
VDD/
IOREF
RESET/RESET
V 3.3/3.3 V
V 5.0/5 V
GND/GND
GND/GND
VIN/Vin
P2_0/A0
P2_1/A1
P2_2/A2
P2_3/A3
P2_4/A4
P2_5/A5
VCC/VDD
GND/GND
SCK/P6_2
MISO/P6_1
MOSI/P6_0
SS/P6_4
P4L_VDD/IOREF
RESET/RESET
V 3.3/3.3 V
V 5.0/5 V
GND/GND
GND/GND
VIN/Vin
NC
VDD/
IOREF
RESET/RESET
V 3.3/3.3 V
V 5.0/5 V
GND/GND
GND/GND
VIN/Vin
RS/P11_5
R/nW/P11_6
EN/P11_4
D4/P11_0
D5/P11_1
D6/P11_2
D7/P11_3
CY8CKIT-046 QUICK START GUIDE
PSoC 4 L-Series Pioneer Board Details
P12_5
P12_7
NC
P3_6
P3_7
P9_0
P9_1
P9_2
P9_3
GND
VLCD
VO
NC
NC
NC
NC
BKLT
GND
PSoC 5LP I/O
GND
P3_0
P3_7
P3_5
P0_1
P1_2
P2_5
P12_0
P12_1
P12_6
P3_6
P3_4
P0_0
VDD
P4_0/SCL
P4_1/SDA
VREF/AREF
GND/GND
P6_2/D13
P6_1/D12
P6_0/D11
P6_3/D10
P0_3/D9
P0_2/D8
P5_5/D7
P5_6/D6
P1_3/D5
P1_2/D4
P1_1/D3
P1_0/D2
P3_1/D1
P3_0/D0
P12_0
P12_1
VREF
GND
P10_2
P10_1
P10_0
P10_3
P5_6
P0_6
P9_5
P9_4
P7_7
P7_6
P7_5
P7_4
P7_3
P7_2
P4_0
P4_1
VREF
GND
P6_2
P6_1
P6_0
P6_3
P6_5
P3_4
P8_7
P8_6
P8_5
P8_4
P8_3
P8_2
P8_1
P8_0
P12_0/SCL
P12_1/SDA
VREF/AREF
GND/GND
P10_2/D13
P10_1/D12
P10_0/D11
P10_3/D10
P10_4/D9
P10_5/D8
P11_7/D7
P11_6/D6
P11_5/D5
P11_4/D4
P11_3/D3
P11_2/D2
P11_1/D1
P11_0/D11
P0_0
P0_1
P4_4
P4_5
P4_6
P4_7
P1_4/A0
P1_5/A1
P1_6/A2
P1_7/A3
P2_6/A4
P2_7/A5
Arduino Uno R3
PSoC 4 L-Series Pioneer Kit
Digilent Pmod
Character LCD
CY8CKIT-046 QUICK START GUIDE
PSOC® 4 L-SERIES PIONEER KIT
PSoC 4 L-Series Pioneer Board Details
32
2129 2628 273031131333
1
2
3
4
5
6
7
8 9 10 11 12 13 14 15 16 17 18 19 20
1. Power (LED2) and Status (LED1) LEDs
2. KitProg USB connector (J10)
3. 32.768 kHz crystal (Y1)
4. PSoC 5LP programmer and debugger
(CY8C5868LTI-LP039, U4)
5. PSoC 5LP I/O header (J8)
6. PSoC 4200L (CY8C4248BZI-L489, U5)
7. PSoC 4200L program and debug header (J6)
8. Digilent
9. Cypress F-RAM 1 Mb (FM24V10-G, U6)
10. PSoC 4200L reset button (SW1)
11. ArduinoTM compatible main board power header (J1)
12. RGB LED (LED3)
13. Arduino compatible main board I/O headers
(J2/J3/J4)
14. User button (SW2)
15. PSoC 4200L current measurement jumper (J14)
16. PSoC 4200L USB connector (J11)
®
PmodTM compatible I/O header (J5)*
17. Audio CODEC (WM8731CLSEFL, U3)
18. Cypress Energy Harvesting PMIC (S6AE101A, U12)*
19. Arduino compatible shield board power header (J17)
20. Character LCD header (J23)*
21. Arduino compatible shield board I/O headers (J18/J19/J20)
22. CapSense Proximity headers (J21, J22)
23. μSD card interface (J25) and Cypress Serial NOR Flash
(S25FL512S, U13)*
24. CapSense
25. EZ-BLETM PRoCTM Module (CYBLE-022001-00, U8)*
26. EZ-BLE Programming header (BLE PROG)*
27. Energy Harvesting PMIC header (EH)*
28. EZ-BLE I/O header (BLE)*
29. Audio jack selection (AHJ/OMTP) switch (SW4)*
30. Audio jack - 3.5 mm (J16)
31. 17.2032 MHz crystal (Y2)
32. System power selection jumper (J9) and LDO (3.3V, U2)
33. PSoC 5LP program and debug header (J7)*
®
Gesture Pad
For the latest information about this kit, visit www.cypress.com/CY8CKIT-046
© 2015 -2018 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the property of their respective owners.
002-02491 Rev.*E
21
22
25
24
23
22
21
*Footprint only, not populated on the board
Loading...