Cypress CY7C1516JV18, CY7C1520JV18, CY7C1518JV18, CY7C1527JV18 User Manual

72-Mbit DDR-II SRAM 2-Word

Burst Architecture

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Features

Functional Description

■ 72-Mbit density (8M x 8, 8M x 9, 4M x 18, 2M x 36)

■ 300 MHz clock for high bandwidth

■ 2-word burst for reducing address bus frequency

■ Double Data Rate (DDR) interfaces

(data transferred at 600 MHz) at 300 MHz

■ Two input clocks (K and K) for precise DDR timing ❐ SRAM uses rising edges only

■ Two input clocks for output data (C and C) to minimize clock

skew and flight time mismatches

■ Echo clocks (CQ and CQ) simplify data capture in high speed

systems

■ Synchronous internally self-timed writes

■ DDR-II operates with 1.5 cycle read latency when Delay Lock

Loop (DLL) is enabled

■ Operates similar to a DDR-I device with 1 cycle read latency in

DLL off mode

■ 1.8V core power supply with HSTL inputs and outputs

■ Variable drive HSTL output buffers

■ Expanded HSTL output voltage (1.4V–V

■ Available in 165-ball FBGA package (15 x 17 x 1.4 mm)

■ Offered in both Pb-free and non Pb-free packages

■ JTAG 1149.1 compatible test access port

■ Delay Lock Loop (DLL) for accurate data placement

)

The CY7C1516JV18, CY7C1527JV18, CY7C1518JV18, and CY7C1520JV18 are 1.8V Synchronous Pipelined SRAM equipped with DDR-II architecture. The DDR-II consists of an SRAM core with advanced synchronous peripheral circuitry and a 1-bit burst counter. Addresses for read and write are latched on alternate rising edges of the input (K) clock. Write data is registered on the rising edges of both K and K driven on the rising edges of C and C edge of K and K is associated with two 8-bit words in the case of CY7C1516JV18 and two 9-bit words in the case of CY7C1527JV18 that burst sequentially into or out of the device. The burst counter always starts with a “0” internally in the case of CY7C1516JV18 and CY7C1527JV18. On CY7C1518JV18 and CY7C1520JV18, the burst counter takes in the least significant bit of the external address and bursts two 18-bit words in the case of CY7C1518JV18 and two 36-bit words in the case of CY7C1520JV18 sequentially into or out of the device.

Asynchronous inputs include an output impedance matching input (ZQ). Synchronous data outputs (Q, sharing the same physical pins as the data inputs D) are tightly matched to the two output echo clocks CQ/CQ capturing data from each individual DDR SRAM in the system design. Output data clocks (C/C) enable maximum system clocking and data synchronization flexibility.

All synchronous inputs pass through input registers controlled by the K or K registers controlled by the C or C domain) input clocks. Writes are conducted with on-chip synchronous self-timed write circuitry.

if C/C are not provided. Each address location

, eliminating the need for separately

input clocks. All data outputs pass through output

if provided, or on the rising

(or K or K in a single clock

. Read data is

Configurations

CY7C1516JV18 – 8M x 8 CY7C1527JV18 – 8M x 9 CY7C1518JV18 – 4M x 18 CY7C1520JV18 – 2M x 36

Selection Guide

Description 300 MHz 250 MHz Unit

Maximum Operating Frequency 300 250 MHz Maximum Operating Current x8 1035 800 mA

x9 1035 800 x18 1045 800 x36 1055 900

Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Document Number: 001-12559 Rev. *D Revised June 25, 2008

[+] Feedback

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Logic Block Diagram (CY7C1516JV18)

Write Reg

CLK

(21:0)

Gen.

Control

Logic

Address

Read Add. Decode

Read Data Reg.

R/W

Output

Logic

Reg.

NWS

[1:0]

REF

Write Add. Decode

Control

R/W

DOFF

4M x 8 Array

[7:0]

CQ CQ

Write Reg

CLK

(21:0)

Gen.

Control

Logic

Address Register

Read Add. Decode

Read Data Reg.

R/W

Output

Logic

Reg.

BWS

[0]

REF

Write Add. Decode

Control

R/W

DOFF

4M x 9 Array

[8:0]

CQ CQ

Logic Block Diagram (CY7C1527JV18)

Document Number: 001-12559 Rev. *D Page 2 of 26

[+] Feedback

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Logic Block Diagram (CY7C1518JV18)

Write Reg

CLK

(21:0)

Gen.

Control

Logic

Address Register

Read Add. Decode

Read Data Reg.

R/W

Output

Logic

Reg.

BWS

[1:0]

REF

Write Add. Decode

Control

Burst

Logic

(21:1)

R/W

DOFF

2M x 18 Array

[17:0]

CQ CQ

Write Reg

CLK

(20:0)

Gen.

Control

Logic

Address

Read Add. Decode

Read Data Reg.

R/W

Output

Logic

Reg.

BWS

[3:0]

REF

Write Add. Decode

Control

Burst Logic

(20:1)

R/W

DOFF

1M x 36 Array

[35:0]

CQ CQ

Logic Block Diagram (CY7C1520JV18)

Document Number: 001-12559 Rev. *D Page 3 of 26

[+] Feedback

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Pin Configuration

Note

1. NC/144M and NC/288M are not connected to the die and can be tied to any voltage level.

The pin configuration for CY7C1516JV18, CY7C1527JV18, CY7C1518JV18, and CY7C1520JV18 follow.

165-Ball FBGA (15 x 17 x 1.4 mm) Pinout

CY7C1516JV18 (8M x 8)

1 2 3 4 5 6 7 8 9 10 11

A CQ AAR/WNWS

B NC NC NC A NC/288M K NWS C NC NC NC V D NC NC NC V E NC NC DQ4 V F NC NC NC V G NC NC DQ5 V H DOFF V

REF

DDQ

J NC NC NC V K NC NC NC V

L NC DQ6 NC V M NC NC NC V N NC NC NC V

SS DDQ DDQ DDQ DDQ DDQ DDQ DDQ

AAAVSSNC NC NC

P NC NC DQ7 A A C A A NC NC NC

R TDO TCK A A A C AAATMSTDI

K NC/144M LD AACQ

ANCNCDQ3

DDQ

[1]

NC NC NC NC NC DQ2 NC NC NC NC NC NC

DDQ

REF

NC DQ1 NC NC NC NC NC NC DQ0 NC NC NC

CY7C1527JV18 (8M x 9)

1 2 3 4 5 6 7 8 9 10 11

A CQ AAR/WNC K NC/144M LD AACQ B NC NC NC A NC/288M K BWS C NC NC NC V D NC NC NC V

E NC NC DQ4 V

F NC NC NC V G NC NC DQ5 V H DOFF V

REF

DDQ

J NC NC NC V K NC NC NC V

L NC DQ6 NC V M NC NC NC V N NC NC NC V

SS DDQ DDQ DDQ DDQ DDQ DDQ DDQ

AAAVSSNC NC NC

ANCNCDQ3

V V V V V V V

DDQ DDQ DDQ DDQ DDQ DDQ DDQ

NC NC NC NC NC DQ2 NC NC NC NC NC NC

DDQ

REF

NC DQ1 NC NC NC NC NC NC DQ0 NC NC NC

P NC NC DQ7 A A C A A NC NC DQ8

R TDO TCK A A A C AAATMSTDI

Document Number: 001-12559 Rev. *D Page 4 of 26

[+] Feedback

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Pin Configuration

The pin configuration for CY7C1516JV18, CY7C1527JV18, CY7C1518JV18, and CY7C1520JV18 follow.

165-Ball FBGA (15 x 17 x 1.4 mm) Pinout

CY7C1518JV18 (4M x 18)

1 2 3 4 5 6 7 8 9 10 11

A CQ AAR/WBWS

B NC DQ9 NC A NC/288M K BWS C NC NC NC V D NC NC DQ10 V

E NC NC DQ11 V

F NC DQ12 NC V G NC NC DQ13 V H DOFF V

REF

DDQ

J NC NC NC V K NC NC DQ14 V

L NC DQ15 NC V M NC NC NC V N NC NC DQ16 V

SS DDQ DDQ DDQ DDQ DDQ DDQ DDQ

AA0AVSSNC DQ7 NC

AAAVSSNC NC NC

P NC NC DQ17 A A C A A NC NC DQ0

R TDO TCK A A A C AAATMSTDI

K NC/144M LD AACQ

ANCNCDQ8

DDQ

[1]

(continued)

NC NC NC NC NC DQ6 NC NC DQ5 NC NC NC

DDQ

REF

NC DQ4 NC NC D3 DQ3 NC NC DQ2 NC DQ1 NC

CY7C1520JV18 (2M x 36)

1 2 3 4 5 6 7 8 9 10 11

A CQ NC/144M A R/W BWS B NC DQ27 DQ18 A BWS C NC NC DQ28 V D NC DQ29 DQ19 V

E NC NC DQ20 V

F NC DQ30 DQ21 V G NC DQ31 DQ22 V H DOFF V

REF

DDQ

J NC NC DQ32 V K NC NC DQ23 V

L NC DQ33 DQ24 V M NC NC DQ34 V N NC DQ35 DQ25 V

SS DDQ DDQ DDQ DDQ DDQ DDQ DDQ

AA0AVSSNC DQ17 DQ7

AAAVSSNC NC DQ10

2 3

K BWS

LD AACQ

KBWS0ANCNCDQ8

V V V V V V V

DDQ DDQ DDQ DDQ DDQ DDQ DDQ

NC NC DQ16 NC DQ15 DQ6 NC NC DQ5 NC NC DQ14

DDQ

REF

ZQ NC DQ13 DQ4 NC DQ12 DQ3 NC NC DQ2 NC DQ11 DQ1

P NC NC DQ26 A A C A A NC DQ9 DQ0

R TDO TCK A A A C AAATMSTDI

Document Number: 001-12559 Rev. *D Page 5 of 26

[+] Feedback

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Pin Definitions

Pin Name IO Pin Description

[x:0]

LD Input-

NWS NWS

BWS BWS BWS BWS

A, A0 Input-

R/W

C Input Clock Positive Input Clock for Output Data. C is used in conjunction with C

K Input Clock Positive Input Clock In put. The rising edge of K is used to capture synchronous inputs to the device

0 1

2 3

Input OutputSynchronous

Data Input Output Signals. Inputs are sampled on the rising edge of K and K clocks during valid write operations. These pins drive out the requested data when the read operation is active. Valid data is driven out on the rising edge of both the C and C mode. When read access is deselected, Q CY7C1516JV18 − DQ CY7C1527JV18 − DQ CY7C1518JV18 − DQ CY7C1520JV18 − DQ

[7:0] [8:0] [17:0] [35:0]

clocks during read operations or K and K when in single clock

are automatically tri-stated.

[x:0]

Synchronous Load. This input is brought LOW when a bus cycle sequence is defined. This definition

Synchronous

Input-

Synchronous

includes address and read/write direction. All transactions operate on a burst of 2 data. Nibble Write Select 0, 1 − Active LOW (CY7C1516JV18 only). Sampled on the rising edge of the K

and K

clocks during Write operations. Used to select which nibble is written into the device during the current portion of the Write operations. Nibbles not written remain unaltered. NWS0 controls D All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select

and NWS1 controls D

[3:0]

[7:4]

ignores the corresponding nibble of data and it is not written into the device.

Input-

Synchronous

Byte Write Select 0, 1, 2, and 3 − Active LOW . Sampled on the rising edge of the K and K clocks during write operations. Used to select which byte is written into the device during the current portion of the write operations. Bytes not written remain unaltered. CY7C1527JV18 − BWS CY7C1518JV18 − BWS0 controls D CY7C1520JV18 − BWS0 controls D

[35:27]

All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select

controls D

[8:0]

and BWS1 controls D

[8:0]

, BWS1 controls D

[8:0]

[17:9].

, BWS2 controls D

[17:9]

and BWS3 controls

[26:18]

ignores the corresponding byte of data and it is not written into the device. Address Inputs. These address inputs are multiplexed for both read and write operations. Internally, the

Synchronous

device is organized as 8M x 8 (2 arrays each of 4M x 8) for CY7C1516JV18 and 8M x 9 (2 arrays each of 4M x9) for CY7C1527JV18, 4M x 18 (2 arrays each of 2M x 18) for CY7C1518JV18, and 2M x 36 (2 arrays each of 1M x 36) for CY7C1520JV18. CY7C1516JV18 – Since the least significant bit of the address internally is a “0,” only 22 external address inputs are needed to access the entire memory array. CY7C1527JV18 – Since the least significant bit of the address internally is a “0,” only 22 external address inputs are needed to access the entire memory array. CY7C1518JV18 – A0 is the input to the burst counter. These are incremented in a linear fashion internally. 22 address inputs are needed to access the entire memory array. CY7C1520JV18 – A0 is the input to the burst counter. These are incremented in a linear fashion internally. 21 address inputs are needed to access the entire memory array. All the address inputs are ignored when the appropriate port is deselected.

Input-

Synchronous

Synchronous Read or Write In put. When LD is LOW , this input designates the access type (read when R/W

is HIGH, write when R/W is LOW) for loaded address. R/W must meet the setup and hold times

around edge of K.

to clock out the read data from

the device. C and C

can be used together to deskew the flight times of various devices on the board back

to the controller. See application example for further details.

Input Clock Negative Input Clock for Output Data. C is used in conjunction with C to clock out the read data from

the device. C and C

can be used together to deskew the flight times of various devices on the board back

to the controller. See application example for further details.

and to drive out data through Q edge of K.

when in single clock mode. All accesses are initiated on the rising

[x:0]

Input Clock Negative Input Clock Input. K is used to capture synchronous data being presented to the device and

to drive out data through Q

when in single clock mode.

[x:0]

Document Number: 001-12559 Rev. *D Page 6 of 26

[+] Feedback

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Pin Definitions (continued)

Pin Name IO Pin Description

CQ Output Clock CQ is Referenced with Respect to C. This is a free running clock and is synchronized to the input clock

for output data (C) of the DDR-II. In the single clock mode, CQ is generated with respect to K. The timing for the echo clocks is shown in the AC Timing table.

ZQ Input Output Impedance Matching Input. This input is used to tune the device outputs to the system data bus

DOFF

TDO Output TDO for JTAG. TCK Input TCK Pin for JTAG. TDI Input TDI Pin for JTAG. TMS Input TMS Pin for JTAG. NC N/A Not Connected to the Die. Can be tied to any voltage level. NC/144M Input Not Connected to the Die. Can be tied to any voltage level. NC/288M Input Not Connected to the Die. Can be tied to any voltage level. V

REF

DDQ

Output Clock CQ is Referenced with Respect to C. This is a free running clock and is synchronized to the input clock

Input DLL Turn Off − Active LOW . Connecting this pin to ground turns off the DLL inside the device. The timing

Input-

Reference

Power Supply Power Supply Inputs to the Core of the Device.

Ground Ground for the Device.

Power Supply Power Supply Inputs for the Outputs of the Device.

for output data (C for the echo clocks is shown in the AC Timing table.

impedance. CQ, CQ, and Q between ZQ and ground. Alternatively, this pin can be connected directly to V minimum impedance mode. This pin cannot be connected directly to GND or left unconnected.

in the DLL turned off operation differs from those listed in this data sheet. For normal operation, this pin can be connected to a pull up through a 10 KΩ or less pull up resistor. The device behaves in DDR-I mode when the DLL is turned off. In this mode, the device can be operated at a frequency of up to 167 MHz with DDR-I timing.

Reference Voltage Input. Static input used to set the reference level for HSTL inputs, outputs, and AC measurement points.

) of the DDR-II. In the single clock mode, CQ is generated with respect to K. The timing

output impedance are set to 0.2 x RQ, where RQ is a resistor connected

[x:0]

, which enables the

DDQ

Document Number: 001-12559 Rev. *D Page 7 of 26

[+] Feedback

CY7C1516JV18, CY7C1527JV18 CY7C1518JV18, CY7C1520JV18

Functional Overview

The CY7C1516JV18, CY7C1527JV18, CY7C1518JV18, and CY7C1520JV18 are synchronous pipelined Burst SRAMs equipped with a DDR interface, which operates with a read latency of one and a half cycles when DOFF When DOFF pin is set LOW or connected to VSS the device behaves in DDR-I mode with a read latency of one clock cycle.

Accesses are initiated on the rising edge of the positive input clock (K). All synchronous input timing is referenced from the rising edge of the input clocks (K and K referenced to the rising edge of the output clocks (C/C when in single clock mode).

All synchronous data inputs (D

) pass through input registers

[x:0]

controlled by the rising edge of the input clocks (K and K). All synchronous data outputs (Q

) pass through output registers

[x:0]

controlled by the rising edge of the output clocks (C/C, or K/K when in single clock mode).

All synchronous control (R/W

, LD, BWS

input registers controlled by the rising edge of the input clock (K). CY7C1518JV18 is described in the following sections. The same

basic descriptions apply to CY7C1516JV18, CY7C1527JV18, and CY7C1520JV18.

Read Operations

The CY7C1518JV18 is organized internally as a single array of 4M x 18. Accesses are completed in a burst of 2 sequential 18-bit data words. Read operations are initiated by asserting R/W HIGH and LD LOW at the rising edge of the positive input clock (K). The address presented to address inputs is stored in th e read address register and the least significant bit of the address is presented to the burst counter. The burst counter increments the address in a linear fashion. Following the next K clock rise, the corresponding 18-bit word of data from this address location is driven onto the Q

using C as the output timing reference.

[17:0]

On the subsequent rising edge of C the next 18-bit data word from the address location generated by the burst counter is driven onto the Q

. The requested data is valid 0.45 ns from

[17:0]

the rising edge of the output clock (C or C , or K and K when in single clock mode, 200 MHz, 250 MHz, and 300 MHz device). To maintain the internal logic, each read access must be allowed to complete. Read accesses can be initiated on every rising edge of the positive input clock (K).

When read access is deselected, the CY7C1518JV18 first completes the pending read transactions. Synchronous internal circuitry automatically tri-states the output following the next rising edge of the positive output clock (C). This enables for a transition between devices without the insertion of wait states in a depth expanded memory.

Write Operations

Write operations are initiated by asserting R/W LOW at the rising edge of the positive input clock (K). The address presented to address inputs is stored in the write address register and the least significant bit of the address is

pin is tied HIGH.

) and all output timing is

, or K/K

) inputs pass through

[0:X]

LOW and LD

presented to the burst counter. The burst counter increments the address in a linear fashion. On the following K clock rise, the data presented to D data register, provided BWS

is latched and stored into the 18-bit write

[17:0]

are both asserted active. On the

[1:0]

subsequent rising edge of the Negative Input Clock (K) the information presented to D register , provided BWS

is also stored into the write data

[17:0]

are both asserted active. The 36 bits

[1:0]

of data are then written into the memory array at the specified location. Write accesses can be initiated on every rising edge of the positive input clock (K). Doing so pipelines the data flow such that 18 bits of data can be transferred into the device on every rising edge of the input clocks (K and K

When the write access is deselected, the device ignores all inputs after the pending write operations have been completed.

Byte Write Operations

Byte write operations are supported by the CY7C1518JV18. A write operation is initiated as described in the Write Operations section. The bytes that are written are determined by BWS

, which are sampled with each set of 18-bit data words.

BWS

and

Asserting the byte write select input during the data portion of a write latches the data being presented and writes it into the device. Deasserting the byte write select input during the data portion of a write enables the data stored in the device for that byte to remain unaltered. This feature can be used to simplify read, modify, or write operations to a byte write operation.

Single Clock Mode

The CY7C1518JV18 can be used with a single clock that controls both the input and output registers. In this mode, the device recognizes only a single pair of input clocks (K and K

) that control both the input and output registers. This operation is identical to the operation if the device had zero skew between the K/K

and C/C clocks. All timing parameters remain the same

in this mode. To use this mode of operation, the user must tie C

HIGH at power on. This function is a strap option and not

and C alterable during device operation.

DDR Operation

The CY7C1518JV18 enables high-performance operation through high clock frequencies (achieved through pipelining) and DDR mode of operation. The CY7C1518JV18 requires a single No Operation (NOP) cycle during transition from a read to a write cycle. At higher frequencies, some applications may require a second NOP cycle to avoid contention.

If a read occurs after a write cycle, address and data for the write are stored in registers. The write information must be stored because the SRAM cannot perform the last word write to the array without conflicting with the read. The data stays in this register until the next write cycle occurs. On the first write cycle after the read(s), the stored data from the earlier write is written into the SRAM array. This is called a posted write.

If a read is performed on the same address on which a write is performed in the previous cycle, the SRAM reads out the most current data. The SRAM does this by bypassing the memory array and reading the data from the registers.

Document Number: 001-12559 Rev. *D Page 8 of 26

[+] Feedback

+ 18 hidden pages

Cypress CY7C1516JV18, CY7C1520JV18, CY7C1518JV18, CY7C1527JV18 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Features

Functional Description

Configurations

Selection Guide

Logic Block Diagram (CY7C1516JV18)

Logic Block Diagram (CY7C1527JV18)

Logic Block Diagram (CY7C1518JV18)

Logic Block Diagram (CY7C1520JV18)

Pin Configuration

165-Ball FBGA (15 x 17 x 1.4 mm) Pinout

Pin Definitions

Functional Overview

Read Operations

Write Operations

Byte Write Operations

Single Clock Mode

DDR Operation