Cypress CPHD-3 Operation Manual

CPHD-3
HDMI V1.3 Pattern
Generator
Operation Manual
CPHD-3
The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
Copyright Notice
No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means
- electronic, mechanical, magnetic, optical, chemical, manual, or otherwise - without express written permission and consent from Cypress Technology.
© Copyright 2009 by Cypress Technology. All Rights Reserved. Version 1.0 July 2009
Trademark Acknowledgments
All products or service names mentioned in this document may be trademarks of the companies with which they are associated.
Safety Precautions
Please read all instructions before attempting to unpack or install or operate this equipment, and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:
Always follow basic safety precautions to reduce the risk of
re, electrical shock and injury to persons.
To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
Do not attach the power supply cabling to building surfaces.
Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
To protect the equipment from overheating, do not block the slot s and openings in the module housing that provi de ventilation.
Revision History
Version No Date Summary of Change
V1 20090803 Preliminary Release
Table of Contents
1
1
1
2
4
4
5
5
7
8
10
10
12
13
14
15
16
21
1. Introduction…………………………………………………........……….
2. Applications………………………………………………........……...….
3. Features………………………………………………........……...…........
4. Specications……………………………………….........……...…........
5. System Requirement………………………….........……...…...............
6. Package Contents………………………….........……...…..................
7. Control Panels………………………….........……...….........................
7.1 Front Pannel………………….........……...….............................
7.2 Rear Pannel………………….........……...…..............................
8. Remote Control………………….............……...…..............................
9. Built-IN RX EDID Structure………............……...…..............................
10. RS-232 Connection and Protocol......……...….................................
11. Features of RS-232 PC Software......……...…....................................
12. RS-232 PC Software Operation......……...…......................................
13. Timing Table………………….........……...….......................................
14. Pattern Table………………….................……...…..............................
15. Description of Patterns……...................……...…..............................
16. Firmware Revision History...................……...….................................
1. Introduction
This HDMI v1.3 compliant video test patter generator is the most advance device for your audio & video signals test. With built-in 39 timings and 51 patterns that accept both analog and digital signals provide over thousand types of testing signals. This handy device can be conveniently controlled via the front panel buttons or the IR remote and a LCD screen for easy viewing. Other then testing your devices this generator can also check the resolution of your devices and record them, check bandwidth and phase behavior transmission, verity video ampliers/color temperature/video motion plus HDCP verication, data comparison, EDID check and many more useful functions.
2. Applications
Apparatus testing
Equipment adjustment
EDID check
Source setting dene
HDCP verication
3. Features
HDMI v1.3, HDCP v1.1 and DVI v1.0 compliant
Provides 39 timings and 51 patterns
Timing included SD, HD up to 1080p, PC up to UXGA/WUXGA (Reduce
Blanking Pixel Rate at 154MHz)
Patterns include Graphic Test Patterns and Data Analysis Patterns
Output format with digital HDMI/DVI, or analog PC/HD (component)
Color Space supports RGB444, YCbCr444 and YCbCr422
Deep Color supports 8 / 10 / 12 bits
Audio source is selectable among external 7.1CH, optical or internal
sinewave
Internal sinewave LPCM channel is selectable from 2CH, 5.1CH and 7.1CH
Supports HDCP test
Support EDID data analysis.
Support HDMI/DVI input data analysis.
Support Autorun function
Choose [My Favorite] timings and patterns through RS-232 using PC
software that included in the box.
Friendly user interface - LCD display, LED indicators, IR remote and RS-232
remote
1
4. Specications
39 Timings: 480 x 640 ~ 1366 x 768 (Details in TIMING TABLE) SD timings: 480i , 480p, 576i and 576p HD timings: 720p up to 1080p PC timings: VGA up to UXGA, WUXGA (Reduce Blanking Pixel Rate at 154MHz)
NOTE > Analog PC output only supports PC timings
Analog HD output only supports SD/HD timings HDMI/DVI output support all timings
NOTE > This system didn't support user timing editing
51 Patterns: (Details in PATTERNS TABLE)
Graphic Test Patterns: 45 Patterns Data Analysis Patterns: 6 Patterns
NOTE > This system didn't support user pattern editing
HDMI/DVI Input & Output:
Signal: TMDS single link and clock bandwidth up to 225MHz Connector: HDMI TYPE-A. DVI input needs DVI to HDMI adaptor
Analog PC/HD Output:
Signal: Analog R/G/B/H/V or analog YPbPr are support color space conversion. Component HD outputs support tri-level sync and color space conversion. Connector: D-SUB15. For HD component output, DB15 to 3-RCA adaptor
cable is required.
Video Color Space and Deep Color:
HDMI Output: RGB444(8/10/12bits), YCbCr444(8/10/12bits) and YCbCr422(8bits) DVI Output:RGB444(8bits) PC Output: RGB with separate sync H/V or
YPbPr with separate sync H/V and without composite sync on Y.
HD Output: YPbPr with composite sync on Y or RGB with composite sync on G.
2
Audio Inputs:
External Analog 7.1CH: RCA jacks. External Optical: Toslink jack. Internal Sinewave:
Supports LPCM 2CH, 5.1CH and 7.1CH. Supports Sampling Rate 48KHz, 96KHz and 192KHz (Refer to Audio Output) Sinewave Frequency: FL (Front Left)=1000Hz, FR (Front Right)=600Hz, CNT (Center)=800Hz, SUB (Subwoofer)=400Hz, SL (Surround Left)=1200Hz, SR¹ (Surround Right)=1400Hz, SBL (Surround Back Left)=1600Hz, SBR (Surround Back Right)=1800Hz
NOTE> This system didn't support bitstream (Dolby, DTS) decoding from
external optical.
Audio Output:
Analog 7.1CH: RCA jacks. Optical: Toslink jack. Coaxial: RCA jack. HDMI: Support I2S bus control. Pattern 38: Audio control functions please refer to below table. (SR1=Samping Rate) 2CH: FL (Front Left) and FR (Front Right). 6CH: FL (Front Left), FR (Front Right), CNT (Center), SUB (Subwoofer), SL (Surround Left) and SR² (Surround Right)
OUTPUT
INPUT
Analog 7.1CH OPTICAL/COAX HDMI
Ext. 7.1CH Bypass
LPCM 2CH SR
1
:48KHz
LPCM 2CH, 6CH SR1:48KHz
Ext. OPTICAL 2CH Bypass Bypass
Int. Sinewave 2CH, 6CH, 8CH
LPCM 2CH SR
1
:48KHz
LPCM 2CH, 6CH, 8CH SR
1
:48K, 96K, 192KHz
Only support 2CH for SR
1
96KHz under 480i/p, 5767i/p,VGA60. Only support 2CH for SR
1
192KHz
3
Pattern 32 - EDID Analysis:
The EDID sources can form three different ways and support 2 block analysis. The system will copy the Sink EDID and built-in into Rx EDID to analysis display information. Below are the three different ways to get the EDID:
1. Built-in Rx EDID
2. From Display HDMI/DVI Sink EDID
3. From Display VGA EDID The EDID analyses are follow VESA E-EDID v1.3 and EIA/CEA 861D Version 3 standard.
Pattern P39 - HDCP Analysis:
This system will do the HDCP handshaking and link-integrity test and it also support Sink Repeater BKSV list and V’ values.
HDMI/DVI Input Analysis:
Support manual Hot-plug (Press [OPTION]) Pattern 48: HDMI/DVI Video Timing Detection and Analysis Pattern 49: HDMI/DVI Video Packets and Infoframe Detection and Analysis. Pattern 50: HDMI Audio Packets and Infoframe Detection and Analysis.
User Interface:
LCD display, LED indicators, IR remote, RS-232 remote: D-SUB9 female connector. PC software supports RS-232 remote control.
5. System Requirement
Video and or audio source input with connecting cables and output display and or speaker(s) with connecting cables.
6. Package Contents
HDMI V1.3 Pattern Generator
Power Adaptor
Remote Control
Operational Manual
4
7. Control Panels
7.1 Front Panel
T01 640x480-60 p01 WHITE
Timing Resolution
Pattern Descrption
Pattern Number
Timing Number Vertical
Frequency
IR Remote Control Sensor.
Timing Selection: Switch between timings from T01 to T39.
Pattern Selection: Switch between patterns from P01 to P51.
For some patterns, it supports OPTION function. After enter option function
and then press Pattern up/down button to adjust the Brightness level.
AUTO: Turn ON/OFF Autorun Demonstration Function. Using PC software through RS-232, users can selecte timings among T01~T39 and patterns among P01~P51 for Autorun demonstration. When Autorun is turn on, the systems will automatically running the selection timings/patterns sequentially.
Output Format Selection: Press the button to switch between PC, HD, DVI and HDMI output.
FAV.: Turn ON/OFF Favorite Function. When switch on the Favorite function, users can select only the favorite timings and favorite patterns. Users need to select favorite timings among T01~T39 and favorite patterns among P01~P51 by using PC software through RS-232. When switch off the Favorite function, users can select all the timings and patterns.
5
HDCP ON/OFF: Turn ON/OFF the HDCP encryption. When the LED illuminate it means the HDCP encryption is on.
Audio Source Selection: Press the button to switch between External
7.1CH(analog), external optical(digital) or internal sinewave audio source.
LPCM Channel Selection: Press the button to switch between 2CH, 5.1CH or 7.1CH LPCM audio channels.
Color Space Selection: Press the button to switch between RGB444, YCbCr444 or YCbCr422 color space.
System Reset: Press two buttons at the same time to reset the system back to factory mode. During the system reset the LCD Display will show "SYSTEM RESET" message.
Deep Color Selection: Press the button to switch between 8bits, 10bits or
bits deep colors.
EDID Pattern: Pattern 32 hot key.
OPTION: Not all the Patterns support function adjustments, when screen shows “Press [OPTION] to do the setting” that means this pattern support function adjustment. When user press the OPTION button the LED will illuminate and then press Pattern +/- button to adjust the Brightness level. Switch off the OPTION function before go to next pattern selection.
HDCP Pattern: Pattern 39 hot key.
6
7.2 Rear Panel
OVERSCAN: When output timing is 480i59/60,480p59/60, 576i50 or 576p50,
the output signal may not showing full image on the screen, press the
OVERSCAN button to ll screen completely.
When signal under OVERSCAN mode, the LCD Display will show STAR (*)
sign at the end of the timing resolution string. Press OVERSCAN to turn off
the overscan mode and the STAR (*) sign will disappear.
PC/HD Output: Connect VGA cable to the VGA monitor for analog PC
timing or HD timing signal output.
HDMI/DVI Output: Connect HDMI or DVI cable to the HDMI or DVI display.
7.1CH Output: Connect 7.1CH to the speaker or Audio Video Receiver.
The audio printed denition as below:
FL:Front Left, FR:Front Right, CNT:Center, SUB:Subwoofer, SL:Surround Left
SR:Surround Right, SBL:Surround Back Left, SBR:Surround Back Right.
OPTICAL Output.
COAXIAL Output.
HDMI/DVI Input: Connect HDMI or DVI Input source to the system.
7.1CH Input: Analog 7.1CH Inputs.
OPTICAL Input
Power Input: Plug 5V DC power adaptor.
RS-232 Connection: Connect RS-232 cable between this system and PC.
Using PC software to control this system through RS-232 port.
Power Switch: Turn ON/OFF the system.
7
8. Remote Control
HDCP ON/OFF: Turn ON/OFF HDCP encryption.
Color Space Selection: Switch between RGB444, YCbCr444 or YCbCr422.
Output Timing Selection
OUTPUT ON: Turn ON/OFF the option function.
Timing - : Backward Timing Selection.
AVMUTE ENABLE: For HDMI output, press to mute the Audio. The LCD Display will show "AVMUTE ON".
AUDIO: Switch between External
7.1CH(analog), external optical(digital) or internal sinewave.
EDID: Pattern 32 hot key.
Output Format Selection: Switch between PC, HD, DVI or HDMI output.
Output OFF: Switch off the output signal. The LCD Display will show "OUTPUT OFF".
Pattern +: Next Pattern Selection. For some patterns, it supports OPTION function. After entering into option function and then press Pattern up/down buttons to adjust the Brightness level.
Timing +:Nex Timing Selection.
OPTION(OK): Not all the Patterns support function adjustments, when screen shows “Press [OPTION] to do the setting” that means this pattern support
function adjustment. When user press the OPTION button the LED will illuminate and then press Pattern +/- button to adjust the Brightness level. Switch off the OPTION function before go to next pattern selection.
AVMUTE DISABLE: For HDMI output, press
to mute the Audio. The LCD display will show “disable AVMUTE”.
Pattern -: Backward Pattern Selection. For some patterns, it supports OPTION function. After enter option function and then press Pattern up/down button to adjust the Brightness level.
Note> Open remote control cover of battery, using dip-switch to set
controller address.
8
9. Built-In Rx Edid Structure:
The system support 4 sets Built-in Rx EDID, one is active and others are for
backup.
The Active EDID will copy the EDID from backup EDID. (Go to "System
Setup" function)
The system will copy the Sink EDID and built-in into Rx EDID to analysis
display information.
RS-232 PC software programs can support Rx EDID contents.
10. RS-232 Connection and Protocol:
Connection between the unit and remote controller with RS-232 modem
cable (No Wire Crossing).
Pin denition
System   Remote Controller
PIN Denition
PIN Denition
1 NC 1 NC
2 TxD
2 RxD
3 RxD 3 TxD
4 NC
4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
RS-232 transmission formats:
Baud Rate=19200bps Data Bit=8bits Parity=None Stop Bit=1bit Flow Control=None
9
Command Description CPHD-3 Response(note 1)
ASC001 ASC002 ASC003 ASC999
Audio source is from external L/R Audio source is from external OPTICAL Audio source is from internal Sinewave Inquire audio source status
ASC001 ASC002 ASC003 ASC???
ATO000 ATO001 ATO999 ATN???
set Autorun Off set Autorun On Inquire Autorun Action status Autorun Number, ???=001~032
ATO000 ATO001 ATO???
ATNxxx (note 2)
ATT??? ATP???
ATI???
ATS999
Autorun Timing, ???=001~039 Autorun Pattern, ???=001~051 Autorun time Interval, ???=005~600 seconds Inquire Autorun Conguration status
ATTxxx
ATPxxx
ATIxxx
ATNxxx + ATTxxx +
CRR???
CRG???
CRB??? CRY??? CRR999
CRG999
CRB999 CRY999
Color Setting Red or Cr, ???=000~255 Color Setting Green or Y, ???=000~255 Color Setting Blue or Cb, ???=000~255 Color Setting Gray, ???=000~255 Inquire Color Setting Red or Cr status Inquire Color Setting Green or Y status Inquire Color Setting Blue or Cb status Inquire Color Setting Gray
CRRxxx
CRGxxx
CRBxxx CRYxxx
CRR???/CRR300 (note 3)
CRG???/CRG300
CRB???/CRB300 CRY???/CRY300
CSC001 CSC002 CSC003 CSC999
Color space is RGB444 Color space is YUV444 Color space is YUV422 Inquire color space status
CSC001 CSC002 CSC003
CSC???
DEE001 DEE002 DEE003 DEE999
Deep Color is 8 bit Deep Color is 10 bit Deep Color is 12 bit Inquire Deep Color status
DEE001 DEE002 DEE003
DEE???
ESC001 ESC002 ESC003 ESC004 ESC005 ESC006
EDID source is from TX (HDMI/DVI out) EDID source is from RX (built-in Active EDID) EDID source is from RX1 (built-in EDID1) EDID source is from RX2 (built-in EDID2) EDID source is from RX3 (built-in EDID3) EDID source is from VGA (PC/HD out)
ESC001 ESC002 ESC003 ESC004 ESC005 ESC006
ERX00? "Name
String"
ERX99?
set RX1,RX2 or RX3 EDID name. ?=1~3 EDID name string, string length is 12 byte Inquire RX1,RX2 or RX3 EDID name. ?=1~3
ERX00? (note 4) ERX004 (note 5)
ERX99? +
"????????????"(note 6)
ERD001
ERS001
EWR001
Read sink's EDID Erase sink's EDID and ll with 'FF' Write EDID to sink
ERD001, datastream (note 7)
ERS001, ERS002/ERS003 (note 8)
EWR001, EWR002/EWR003
(note 9)
FAV000 FAV001 FAV999
set My Favorite Off set My Favorite On Inquire My Favorite action status
FAV000 FAV001 FAV???
Command / Response codes of RS-232 transmission:
10
FP+???
FP-???
FP+999 or FP-
999
Add Favorite PATTERN, ???=001~051 Drop Favorite PATTERN, ???=001~051 Inquire Favorite PATTERN status
FP+xxx
FP-xxx
FP+??? FP-???
FT+???
FT-???
FT+999 or FT-
999
Add Favorite TIMING, ???=001~039 Drop Favorite TIMING, ???=001~039 Inquire Favorite TIMING status
FT+xxx
FT-xxx
FT+??? FT-??? ...
HDC000 HDC001 HDC999
set HDCP Off set HDCP On Inquire HDCP status
HDC000 HDC001 HDC???
MOT001
"Custom
String"
MOT999
set Pattern 46.Motion's custom string. Custom string, string length is 12 byte Inquire Motion Pattern's custom string
MOT001 (note 10) MOT002 (note 11)
MOT999 + "????????????"(note 12)
OUT001 OUT002 OUT003 OUT004 OUT999
Select output format [PC] Select output format [HD] Select output format [DVI] Select output format [HDMI] Inquire output format status
OUT001 OUT002 OUT003 OUT004 OUT???
PAT???
PAT999
Select PATTERN P01~P50, ???=001~051 Inquire PATTERN status
PATxxx
PAT???
PCM001 PCM002 PCM003 PCM999
set LPCM 2CH set LPCM 5.1CH set LPCM 7.1CH Inquire LPCM Channel status
PCM001 PCM002 PCM003
PCM???
RST001 System reset RST001
TIM???
TIM999
Select TIMING T01~T39, ???=001~039 Inquire TIMING status
TIMxxx
TIM???
VER999 Inquire rmware version. VER???(Ex:VER021=V2.1)
note 1: After computer sends command to the system, computer has to wait
for response from the system. Then computer can send next command to the system. If this system is under autorunning, RS-232 communications maybe fail.
note 2: To congurate Autorun follows a sequence of commands --- ATNxxx +
ATTxxx + ATPxxx + ATIxxx
note 3: If this system is not on Pattern 47.Color Setting, respond CRR300,
CRG300, CRB300 or CRY300.
note 4: Procedure of setting RX EDID name string :
send "ERX00?" -> wait "ERX00?" response -> send name string (12 bytes)
-> wait "ERX004"
note 5: In the name string, the rest unused bytes (<12bytes) should be lled
with 0x00.
11
note 6: After ERX99? response, name string (12 bytes) is followed. note 7: After ERD001 response, this system reads sink's EDID and transmits
them (datastream) to remote terminal If this system reads sink's EDID fail, the system sends '0xfe' and stop datastream. This system supports 2-block EDID, datastream length=block0+block1=256 bytes
note 8: After ERS001 response, this system erases sink's EDID and ll with 'FF'.
After erase completely, the system reponses ERS002 If erase fail, the system responses ERS003
note 9: After EWR001 response, this system will waits for EDID datastrem(256
bytes) from PC After receive datastream completely, the system writes datastream to sink. If write successfully, the system responses EWR002, otherwise EWR003
note 10: Procedure of setting custom string :
send "MOT001" -> wait "MOT001" response -> send custom string (12 bytes) -> wait "MOT002"
note 11: In the custom string, the rest unused bytes (<12bytes) should be lled
with 0x00. Custom string supports English language only.
note 12: After MOT999 response, custom string (12 bytes) is followed.
11. Features of RS-232 PC Software
Click button and upload selected timing or pattern.
Select [My Favorite] timings and patterns.
Read out EDID contents from sink.
Write EDID contents to sink.
Can be an EDID burner.
Analyze EDID data and generate a report le.
Congurate Autorun [AUTO] List.
Panel Controls through RS-232
Monitors System status.
Edit custom string of Motion Pattern (Pattern 46).
Adjust color-levels pattern (Pattern 47).
12
12. RS-232 PC Software Operation
Main Function Selection: Timing Select:Select a timing among T01~T39 Pattern Select:Select a pattern among P01~P51
Favorite Timing:Select favorite timings among T01~T39 Favorite Pattern: Select favorite patterns among P01~P51 EDID Read/Write: Read, write EDID contents and analyze EDID data. Autorun Cong: Congurate autorun list. Panel Control: Control system functions.
Status Monitor: Click [Refresh] button to get system status.
Work Area: Different main functions have independent work area.
About: Get PC software and system rmware version number.
RS-232 Setup: Select RS-232 Comport and turn on/off connection.
13
13. Timing Table
No. Resolution V Hz No. Resolution V Hz
T01 T02 T03 T04 T05 T06 T07 T08 T09 T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20
640x480 640x480 640x480 640x480 800x600 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1024x768 1280x960 1280x960 1280x1024 1280x1024 1280x1024 1600x1200 1920x1200
60 72 75 85 56 60 72 75 85
60 70 75 85 60 85 60 75 85 60 60
T21 T22 T23 T24 T25 T26 T27
T28 T29 T30 T31 T32 T33
T34 T35 T36 T37 T38 T39
720x480i 720x480i 720x480p 720x480p
1280x720p
1280x720p 1920x1080i 1920x1080i 1920x1080p 1920x1080p 720x576i 720x576p 1280x720p 1920x1080i 1920x1080p 1920x1080p 1920x1080p 1366x768 1366x768
59 60 59 60
59 60
59
60 59
60 50 50
50
50 50 23 24 60 50
14
14. Pattern Table
Graphic Test Patterns: 45 Patterns
Data Analysis Patterns: 6 Patterns (Include P32, P38, P39, P48, P49, P50)
P01 WHITE P24 MULTI-BURST P02 BLUE P25 Pluge P03 RED P26 GRID-1 P04 MAGENTA P27 GRID-36 P05 GREEN P28 GRAY-256-R P06 CYAN P29 GRAY-256-G P07 YELLOW P30 GRAY-256-B P08 BLACK P31 CIRCLES P09 RED Setting
P32
EDID P10 GRN Setting P33 H Grey Scale P11 BLUE Setting P34 Hori.RGB Bar P12 GRAY Setting P35 SMPT Bar P13 COLOR BAR P36 Split Bar P14 GRAY-8 P37 CROSS HATCH P15 GRAY-16
P38
AUDIO P16 GRAY-32
P39
HDCP P17 GRAY-64 P40 Win Blue P18 GRAY-256 P41 Win Red P19 V line ONOFF P42 Win Magenta P20 BW-12 P43 Win Green P21 H line ONOFF P44 Win Cyan P22 HOR.-3 P45 Win Yellow P23 HOR.-6 P46 Motion
P47 Color Setting
P48
Rx Timing
P49
Rx Video
P50
Rx Audio
P51 RGB Delay System Setup
15
15. Description of Patterns
GROUP NO. PATTERN DESCRIPTION
Full Screen Purity
P01
Purity pattern Purity offers eight different full
eld patterns: Black, White (100% Y) Primary colors: Red, Green, Blue
Complementary colors: Magenta, Yellow, Cyan
P01: White P02: Blue P03: Red P04: Magenta P05: Green P06: Cyan P07: Yellow P08: Black
P02
P03
P04
P05
P06
P07
P08
Application
1. The red and green patterns are most frequently used for checking color purity. The red pattern is selected only this color should be
visible; the presence of any other color is an indication that color purity needs adjustment.
2. The green pattern provides a purity check for three in-line tubes. In the
in-line tubes, the guns are in a horizontal position and the green gun is located in the center.
3. The blue is the complementary colors are often used to check the color performance.
4. The red are used to ensure that there is no interference between the sound and chroma carrier. Furthermore the red pattern is used to adjust the long play delay level to minimum
icker.
5. In addition to the primary and complementary colors 100% white can be selected as well as black pattern with color burst to check.
16
Color Setting
P09 Red Setting P10 Green Setting P11 Blue Setting P12 Gray Setting
Press [OPTION],[PATTERN -/+] to adjust color level. There are 11 steps to adjust color level: 0, 25, 51, 76, 102, 127(default), 153, 178, 204, 229 and 255.
P47 Color Setting
Through RS-232 PC software to adjust each color component value.
Application This pattern is for brightness control and luminance writing current. This can
overall the color performance, amplitude response/resolution and linearity of chroma amplitude.
Color Bar
P13 8 Bars
P34 Hori. RGB Bar
P35 SMPTE Color Bar
P36 Split Color Bar
P51 RGB Delay
Application
The Color matrix test is to test for xed quantity of color. To sum up, test for R, G, B color bar.
Gray Scale
P14 8 steps
P15 16 steps
P16 32 steps
P17 64 steps
P18 256 steps
P33 H Grey Scale
17
Application
This is used to locate faulty linearity of the video
amplier
or greyscale
setting. Nonlinearities mainly result in a compression of the white level.
Black White Line
P19 Vertical BW1 (black 1 pixel, white 1 pixel)
P20
Vertical BW12(black 12 pixels, white 12 pixels)
P21 Horizontal BW1(black 1 pixel, white 1 pixel)
P22
Horizontal BW3(black 3 pixels, white 3 pixels)
P23
Horizontal BW6(black 6 pixels, white 6 pixels)
P24 Multi-Burst BW6+BW3+BW2+BW1
Application
The Vertical pattern serves for a quick check of a color monitor’s horizontal bandwidth and phase behavior of a video transmission. It also, verify video ampli
er
and color temperature.
The Horizontal pattern serves for a quick check of color monitor’s vertical bandwidth and phase behavior of a video transmission. It also, verify video amp
li
er and
color temperature.
PLUGE
P25
Picture Line-Up Generation Equipment Press [OPTION] to select color range Full Range=0~255, Limited Range=16~235 PC/HD output gets Full Range=0%~100%
Application
PLUGE is used to perform accurate and consistent line-up of picture monitors. The usual procedure is to adjust the brightness control of a monitor so that bar 1 is invisible on the background while bar 2 can be still distinguished. The white level luminance is mainly adjusted by the contrast control to 70 ±10 cd/m2 by means of the upper 100% white area of the vertical grayscale.
18
Grid
P26 1x1(pixel) checkerboard
P27
36x36(pixels) checkerboard
P37
Cross Hatch Press [OPTION] to inverse black/white.
Application
This pattern is mainly used for checking and aligning dynamic and corner convergence of TVs or monitors.
Gradient
P28 Red Gradient
P29 Green Gradient
P30 Blue Gradient
Application
This is used to locate faulty linearity of the video
amplier
. Nonlinearities
mainly result in a compression of the color level.
Circle
P31 Circles
Application
It’s suited for checking the overall linearity and geometry of the screen of a monitor or TV.
EDID
P32
EDID Analysis Press[OPTION],[PATTERN -/+] to analyze sink’s EDID contents.
Audio
P38
Audio Control Source, Channel Number, Sampling Rate, I2S Controls
HDCP
P39
HDCP handshaking and link-integrity test If sink is a repeater, press [OPTION] to show BKSV List / V’ value.
19
Window Purity
P40
75% of Height/Width Window Pattern.
P41
P42
P43
P44
P45
Application
The Monitor is controlled by electromagnetism which is made at the monitor. If the magnetism is made from monitor, distortion condition can be appeared because monitor is controlled by electromagnetism. If there isn’t any distortion condition, we say, that monitor has good condition related by the 75% color purity.
Motion
P46
Font base motion test. Press [OPTION] to select motion object. Through RS-232 PC software, edit custom string.
Application
This test pattern can be used to check the correct digital video processing, especially AD conversion of modern TV equipment. Moving pictures or slow motion function can be checked on VCRs by the pattern.
20
Rx Data Analysis
P48
HDMI/DVI input timing detection and analysis. Press [OPTION] to pull hot-plug NOTE> The values below are approximation. Pixel Rate, Horizontal Frequency, Vertical Frequency Those are for reference only.
P49
HDMI/DVI input video packets and info­frames detection ­and analysis. Press [OPTION] to pull hot-plug
P50
HDMI input audio packets and infoframes detection and analysis. Press [OPTION] to pull hot-plug
Sys Setup
System Setup Built-in Rx EDID setup, IR remote address setup.
16. Firmware Revision History
Version Release Date Description v1.0 2009.06.19 First release
v1.1 2009.07.xx Add pattern 51-RGB Delay.
21
Acronyms
A
Acronym Complete Term
CAT5 Category 5 Cable
IR Infrared
DC Direct Current
GND Ground
22
20090811 MPM-CPHD3
Home page: http://www.cypress.com.tw
CYPRESS TECHNOLOGY CO., LTD.
Loading...