Cypress CM-393 Operation Manual

Scart/Video to

HDMI Scaler Box

Operation Manual

CM-393

(1). Introduction:

Congratulations on your purchase of the Cypress Video Scaler CM-393.
Our professional Video Scaler products have been serving the industry
for many years.
In addition to Video Scalers, Cypress offers a full line of high quality
PC multimedia,Standard Converters, HDMI/DVI Splitters and Switchers
Video Mixer, Time Base Correctors,and Video Processors.
Please visit www.cypress.com.tw to learn more details about

these products.
This manual includes operation information on the CM-393 model.
Please read this to become familiar with the CM-393 and keep the manual
for possible reference in the future.
Cypress's CM-393 is designed to scale up scart, Composite and S-Video to
HDMI output.It also accepts two HDMI inputs that can be switched with

scaled-up HDMI and bypassed to the HDMI output. Cypress CM-393 has
many

great features to

enhance video performance and is ideal for use in

professional large screen presentation.

(3) This package includes:

1. Video Scaler Unit.

2. DC adaptor.

3. S-Video cablex1.

4. Audio cable 2 RCA to 3.5mm phone jack x1.

5.1RCA-1RCA video cable x1.

6. User Manual.

7. Remote Control.

8. Lithium battery.

(2). Features:

1. Scales up 2 scarts, 1 composite, and 1 S-Video to high definition HDMI fromat.

2. Accepts 2 x Scart/ 1 x Composite/ 1x S-Video, each with audio,

and 2x HDMI inputs.

3. Audio lip-sync(audio delay) ensures perfect synchronization between video

and audio output.

4. Input video systems- NTSC 3.58/PAL/RGB50Hz/ RGB60Hz auto detection.

5. HDMI output resolution- VGA /SVGA/XGA/WXGA/SXGA/480P/576P/720P/
540P(pseudo 1080i).

6. 3D(frame Based)motion adaptive YNR/CNR noise reduction (for Y/C video input)

7. Advanced 3D motion adaptive deinterlace

8. Automatic 2：2/3：2 film mode detection

9. Supports 50Hz to 60Hz frame rate conversion

10. Video quality improvement：
DCT1( Digital chroma transient improve ),

DLT1( Digital luminance transient improve ),

Black level extension.

11.

Average picture level ( APL ), Automatic contrast limiter ( ACL )
function supported.

12. OSD menu for picture quality adjustment- bright/contrast/color/tint/sharp.

13. Built in 8-bit DAC for RGB or YPbPr output.

14. Front Panel and IR remote control.

15. Automatic NTSC/PAL video format detection and switching.

11

1. Power button and LED indicator:

Press the button once to power on the unit, Press again to power off (Standby).
when the unit is powered on,

the LED illuminates in green. When the unit is in
standby the LED illuminates in RED. To complete power off the unit disconnect
the power cable from the power plug on the back of the unit.

2. Input select button:

Press the button repeatedly to select your desired input source by toggling
though 6 input sources.

The factory default input setting is scart 1.
The CM-393 has last memory capability to memorize the last input selected
before power down and to return to that input when power back on again.

3. IR Sensor: Infrared remote control sensor.

4. Menu/Enter: This button serves two purposes.

a. Press the button to enter OSD main control menu as shown in the "OSD Operation".
b. To act as a "enter" key to enter sub menu of your selected item.
5/6. +/- button: Press the button to move up or down the cursor to your
d

esired parameter. Or after a parameter is selected,

Press the button to alter

the value of your selected parameter.

Front Panel

(4). Operation Controls and Functions:

2

Rear Panel

1. DC power jack: 5V 2A DC power input.

2. SCART 1: Use a scart cable to connect the scart output of your source

equipment to this scart input.
The DC voltage on scart pin-16(fast blanking) from the source equipment will
decide whether output from source device is RGB Sync or composite.
In case if pin-16 is floating or pull high, the CM-394 will set to RGBS mode.
Otherwise it will be set to composite mode. The detection of pin-16
voltage from the source and therefore the signal format is carried out
automaticaly on CM-393.

3. SCART 2: Use a scart cable to connect the scart output of your 2nd scart
source to this scart input of the CM-393.

1 23 4 5 6

Scart 1 Scart 2 composite S-video HDMI 1 HDMI 2

4 5 7 8 9 10

6

3

2

1

SV

Audio

In

CV

Audio

In

POWER INPUT MENU