Cypress CLUX-SDI2HS User Manual

CLUX-SDI2HS

SDI to HDMI Scaler with Audio

Operation Manual

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.

Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

© Copyright 2011 by Cypress Technology.

All Rights Reserved.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this
equipment:

• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.

• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

VR0 25/03/11 Preliminary Release

VR1 28/09/11 Add Support Timing

VS2 11/07/12 Updated format/diagrams/SDI

standards

VS3 19/07/12 First release

CONTENTS

1. Introduction ............................................ 1

2. Applications ........................................... 1

3. Package Contents ................................ 1

4. System Requirements ............................ 1

5. Features .................................................. 2

6. Operation Controls and Functions ....... 3

6.1 Front Panel ........................................3

6.2 Rear Panel .........................................4

6.3 OSD Menu and Function List ........... 5

6.3.1 Display ............................................7

6.3.2 Color ...............................................7

6.3.3 SDI Audio ........................................8

6.3.4 Factory Reset ..........................8

6.3.5 Information ..............................9

7. Connection Diagram .......................... 10

8. Specications ...................................... 11

9. Acronyms ............................................. 12

1. INTRODUCTION

The SDI to HDMI Scaler allows SD, HD and 3G-SDI signals to be
shown on HDMI and SDI display. This means that it is now easier for

professionals to distribute and extend their SDI signal while giving the
ability to display work on HDMI displays. Furthermore, thanks to coaxial

(S/PDIF) and L/R audio outputs users can output audio in both digital

and analog formats while the loop-through 3G-SDI design benets

users by letting them simultaneous show content on both SDI and
HDMI displays.

2. APPLICATIONS

• Broadcast video signal to HDMI/SDI display

• Broadcast video signal extension

• 3G SDI signal conversion into HDMI signal

3. PACKAGE CONTENTS

• SDI to HDMI Scaler with Audio

• 5V/2.6A DC power adaptor

• Operation Manual

4. SYSTEM REQUIREMENTS

Input source equipment such as SNG camera or any SDI signal
with connection cables and output to LCD TV or SDI monitor with
connection cables.

1

5. FEATURES

• Supports SD-SDI, HD-SDI and 3G-SDI input signals with auto-detection

• Supports HDMI and SDI (bypass) output simultaneously

• SDI interface operates at bitrates of 2.970 Gbit/s, 2.970/1.001 Gbit/s,

1.485 Gbit/s, 1.485/1.001 Gbit/s and 270 Mb/s

• Scale any SDI input signal to HDMI:

1. PC timings – SVGA@60 ~ WUXGA@60 (RB)

2. HDTV timings – 480p/576p ~ 1080p@50/60

• Supports SDI input modes:

1. SD-SDI (SMPTE 259M-C, at bitrates of 270 Mbit/s)

2. HD-SDI (SMPTE 292M, at bitrates of 1.485 Gbit/s and

1.485/1.001 Gbit/s)

3. 3G-SDI (SMPTE 424M/425M-AB, at bitrates of 2.970 Gbit/s and

2.970/1.001 Gbit/s)

• Equalized and re-clocked loop output

• Alternative audio output to coaxial and analog 2 CH

• Integrated audio de-embedder for up to 8 channels of 48 kHz audio

• Supports SDI input/output distance up to 100 meters (3G-SDI), 200

meters (HD-SDI), or 300 meters (SD-SDI)

Note: Tested with Belden 1694A Cable. Operating distances may vary

if used with cables of different specications.

2

6. OPERATION CONTROLS AND FUNCTIONS

1

2

3

4

5

6

7

6.1 Front Panel

720p

-

+

XGA

POWER 3G HD SD MENU ENTER

3G SDI to HDMI Scaler CLUX-SDI2HS

2 3 4 5 6 71

Power LED: The LED will illuminate blue when the device is

connected to a power supply.

3G LED: This LED illuminate green when a 3G-SDI input signal is

detected.

HD LED: This LED illuminate green when a HD-SDI input signal is

detected.

SD LED: This LED illuminate green when a SD-SDI input signal is

detected.

MENU: Press this button to enter/exit the On-Screen Display (OSD)

menu.

ENTER: Press this button to conrm your selection. Press both ENTER

and 'Minus' (−) buttons together to switch the display output to

720p or press both ENTER and 'Plus' (+) buttons together to switch

to XGA. After making the selection, press ENTER to conrm the

output format.

−/+: Press these buttons to move up or down the OSD selections.

3

6.2 Rear Panel

1

2

3

4

5

6

SDI IN SDI OUT

AUDIO OUT

COAXIAL R

HDMI OUT

L

DC 5V

1 2 3 4 5 6

SDI IN: Connect to the SDI output of the SDI source device.

Accepts SD,HD or 3G SDI signals.

SDI OUT: Provides a 'loop-through' SDI signal output for connection

to a SDI display.

AUDIO OUT COAXIAL: Digital Audio output (SP/DIF). Connect to an

amplier or recording device with a suitable digital coaxial input.

AUDIO OUT R/L: Analogue audio output (L/R Stereo). Connect to

an amplier or recording device with a suitable analogue input.

HDMI Out:Connect a HDMI equipped display or to a DVI Display

with a HDMI to DVI cable.

DC 5V: Plug the 5 V DC power supply into the unit and connect the

adaptor to an AC outlet. The 'POWER' LED will illuminate blue when
the power is ON.

4

6.3 OSD Menu and Function List

1st Layer 2nd Layer 3rd Layer

NATIVE

800 x 600 @60

1024 x 768 @60

1280 x 768 @60

1360 x 768 @60

1280 x 800 @60

1280 x 1024 @60

1440 x 900 @60

1400 x 1050 @60

Output

Display

Size

Exit

1680 x 1050 @60

1600 x 1200 @60

1920 x 1200 @60

720 x 480p @60

1280 x 720p @60

1920 x 1080p @60

720 x 576p @50

1280 x 720p @50

1920 x 1080p @50

1920 x 1080i @60

1920 x 1080i @50

Full

Over Scan

Under 1

Under 2

Letter Box

Pan Scan

5

Contrast 0~255 (105)

Brightness 0~192 (96)

R 0~255 (128)

G 0~255 (128)

Color

SDI Audio

Factory Reset Yes

Information Input Timing, Output Timing & Version

B 0~255 (128)

R Offset 0~63 (32)

G Offset 0~63 (32)

B Offset 0~63 (32)

Exit

Group 1

Group 2

Group 3

Group 4

Auto

Off

6

6.3.1 Display

• Output Timimgs: There are a total of 20 timings available for

selection.

• Size: Adjusts the displayed screen size from Full, Over Scan, Under

Scan, Letter box or Pan scan to t the current display size or aspect

ratio.

6.3.2 Color

• Adjusts the screen's RGB Color, Contrast and/or Brightness.

7

6.3.3 SDI Audio

• Selects the SDI audio output from 4 different audio groups and each

group's 2CH contents or can be set to 'Auto' which contain up to

7.1 Channels of audio (dependent on the input source signal). If no
audio output is required, the audio can also be muted by selecting
'OFF'.

6.3.4 Factory Reset

• Select YES to return the unit to the factory settings. The default

Factory Setting for Video display is 'Full Screen' (1280×720@60Hz),

Color setting's factory default rate is the same as shown on the OSD
and SDI audio is 'AUTO'.

8

6.3.5 Information

• Displays the source input format, the output display format and the

unit's software version.

9

7. CONNECTION DIAGRAM

SDI DisplaySDI Camera

Coaxial
Digital
Audio
Output

Amplier

SDI IN SDI OUT

Stereo
Audio
Output

SDI OutputSDI Input

AUDIO OUT

COAXIAL R

Power
Supply

DC 5V

HDMI OUT

L

HDMI
Output

HDTV/Monitor

10

8. SPECIFICATIONS

SMPTE Standard 425M Level A & B, 424M, 292M, 259M-C

SDI Transmission Rates 2.970 Gbps, 2.970/1.001 Gpbs

1.48 5 Gbps, 1.485/1.001Gbps and 270
Mbps

Video Bandwidth 165 MHz/link

Input 1×BNC (SD/HD/3G-SDI)

Output 1×BNC (SD/HD/3G-SDI), 1×HDMI,

1×Coaxial, 1×L/R (RCA)

SDI Timing Support SD-SDI:

SMPTE 259M-C, 270 Mbit/s
HD-SDI:
SMPTE 292M, 1.485 & 1.485/1.001 Gbit/s
3G-SDI:
SMPTE 424M/425M-AB, 2.970 &

2.970/1.001 Gbit/s

HDMI Timing Support 480i, 576i, 720p@50/59.94/60

1080i@50/59.94/60
1080p@23.98/24/25/29.97/30/50/59.94/60

Power Supply 5 V DC/ 2.6 A (US/EU standards, CE/FCC/UL

certied)

ESD Protection Human-body Model:

± 8kV (air-gap discharge)
± 4kV (contact discharge)

SDI Cable Distance 3G/HD/3G-SDI up to 100 /200/300 meters

with BELDEN 1694A Cable

Dimension 180 mm (W)×142 mm (D)×25 mm (H)

Weight 460 g

Chassis Material Aluminum

Silkscreen Color Gray

Operating Temperature 0 °C~40 °C/32 °F~104 °F

Storage Temperature −20°C ~ 60°C / -4°F ~ 140°F

Relative Humidity 20~90 % RH (Non-condensing)

Power Consumption 4 W

11

9. ACRONYMS

ACRONYM COMPLETE TERM

3G Bandwidth 2.97G bps ≈ 3G

SDI Serial Digital Interface

HD High Denition

12

CYPRESS TECHNOLOGY CO., LTD

Home page: http://www.cypress.com.tw