Cypress CLUX-SDI2CSS Operation Manual

CLUX-SDI2CSS

SDI to CV/SV Scaler with

Audio

Operation Manual

CLUX-SDI2CSS

Disclaimers

The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes
no commitment to update or to keep current the information
contained in this document.
Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

Copyright Notice

No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means

- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.

© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.0 May 2011

Trademark Acknowledgments

All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

Safety Precautions

Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:



Always follow basic safety precautions to reduce the risk of

re, electrical shock and injury to persons.



To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.



Never spill liquid of any kind on or into this product.



Never push an object of any kind into this product through

module openings or empty slots, as you may damage parts.



Do not attach the power supply cabling to building surfaces.



Do not allow anything to rest on the power cabling or allow it to

be abused by persons walking on it.



To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.

Revision History

Version No Date Summary of Change

VR0 20110513 Preliminary Release
VR1 20110928 Spec. Transmission Typo

Table of Contents

1
1
1
2
3
4
4
5
6
7
7
7
8
8
9

10

1. Introduction ……………………..……………………...…........….…….

2. Applications …………………..………………….……...................…..

3. Package Contents ………………………...........……….................…

4. Features …………………………………………......……........…...……

5. Specications ………………………………...……..........………....….

6. Operation Controls and Functions ……………...……..............……

6.1 Front Panel ..............................................................................

6.2 Rear Panel .…………………………………..…….......…...….…

7. OSD Menu and Function List ...................………..........…..…....…...

7.1 Display .................…......................……………..........…..…....….

7.2 Color .........…..….....................................................................….

7.3 SDI Audio ...................................................................…..…....….

7.4 Factory Reset ............................................................…..…....….

7.5 Information ...............................................................…..…....….

8. Connection and Installation ….………………….........…..…..…......

9. Acronyms …......................................................................................

1. Introduction

The SDI to CV/SV Scaler with Audio allows SD, HD and 3G-SDI signals to be
display on CV/SV displays while ensuring high bit rates of 2.970 Gbps gives
you fast signal transmission without signal loss. For professional this means that
it is now easier to distribute and extend your SDI signal while giving you the
ability to display your work on the existing CV/SV displays. Further, the design
of coaxial and L/R audio output allows user to output audio with both digital
and analog format and the loop-through 3G-SDI design also benet user to
enjoy both SDI and CV/SV display synchronously.

2. Applications



Broadcast video signal sending to SDI display



3G SDI signal convert into CV/SV signal

3. Package Contents



SDI to CV/SV Scaler with Audio



5V/2.6A DC power adaptor



Operation Manual

1

4. Features



Operation at 2.970Gbps, 2.970/1.001Gbps, 1.485Gbps, 1.485/1.001Gbps

and 270Mbps



Supports SMPTE 425M (Level A and Level B), SMPTE 424M, SMPTE 292M,

SMPTE 259M-C



Equalized and re-clocked loop output



Alternative audio output to coaxial and analog 2CH



Auto video mode detection (3G/HD/SD)



Conversion from SMPTE 425M level B to Level A for 1080p 50/59.94/60 4:2:2

10-bit



Supports NTSC/PAL output

2

5. Specications

SMPTE Standard 425M Level A & B, 424M, 292M, 259M-C
SDI Transmission Rates

2.970 Gbps and 2.970/1.001 Gbps, 1.485Gbps,

1.485/1.001Gbps, and 270Mbps
Input Port 1 x BNC (SD/HD/3G-SDI)
Output Port 1 x BNC (SD/HD/3G-SDI),

1 x CV, 1 x SV, 1 x Coaxial, 1 x R/L RCA Jack
Video Output Support NTSC/PAL
SDI In/Out Support Timing 480i, 576i, 720p@50/59.94/60, 1080i@50/59.94/

60, 1080p@23.98/24/25/29.97/30/50/59.94/60

1080Ps

F@23.98/24/25/29.97/30

Power Supply 5V DC/ 2.6A (US/EU standards,

CE/FCC/UL certied)
ESD Protection Human body model:± 8kV (air-gap discharge)

±

4kV (contact discharge)

SDI Cable Distance 3G up to 100M (BELDEN 1694A Cable)

HD up to 200M (BELDEN 1694A Cable)

SD up to 300M (BELDEN 1694A Cable)
Dimensions (mm) 180(W) x 142(D) x 25(H)
Weight(g) 435
Chassis Material Aluminum
Silkscreen Color Gray
Operating Temperature 0˚

C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature -20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity 20 ~ 90% RH (Non-condensing)
Power Consumption (W) 8.5

3

6. Operation Controls and Functions

6.1 Front Panel

POWER3GHDSD MENUENTER

-

+

NTSC

PAL

3G SDI to Video Scaler CLUX-SDI2CSS

① ② ③ ④ ⑤ ⑥ ⑦

①

Power LED: This blue LED will illuminate when the device is connected with

power supply.

②

3G LED: This green LED illuminate when the input SDI signal is with 3G

format.

③

HD LED: This green LED illuminate when the input SDI signal is with HD

format.

④

SD LED: This green LED illuminate when the input SDI signal is with SD

format.

⑤

MENU: Press this button to enter/exit the OSD menu.

⑥

ENTER: Press this button to confirm your selection. Press both ENTER and
– buttons together to switch output timing to NTSC format instantly or
press both ENTER and + buttons together to switch output timing to PAL
format. After the selelction press ENTER to confirm the output format.

⑦

-/+: Press these buttons to move up or down the OSD selections.

4

6.2 Rear Panel

SDI IN SDI OUT

AUDIO OUT

DC 5V

COAXIAL R

L

S VIDEOVIDEO

① ② ③ ④ ⑤ ⑥

①

SDI IN: This slot is where you connect the SDI source output for SDI signal
sending to be display on screen.

②

SDI OUT: This slot is where you connect the SDI display with SDI cable for
input source display.

③

AUDIO OUT COAXIAL: This slot is where you connect the amplifier with
coaxial cable and from amplifier to speaker

④

AUDIO OUT R/L: These slots are where you connect the speaker or
amplifier with RCA jack for audio signal display.

⑤

These slots are to connected with display TV or monitor with CV/SV
cable(s).

⑥

DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to AC wall outlet. Blue LED will illuminate when the power is ON.

5

7. OSD Menu and Function List

1st Layer 2nd Layer 3rd Layer

Display

Output

NTSC

PAL

Size

Full

Over Scan

Under 1
Under 2

Letter Box

Pan Scan

Exit

Color

Contrast 0~255(105)

Brightness 0~192(96)

R 0~255(128)

G 0~255(128)

B 0~255(128)

R Offset 0~64(32)

G Offset 0~64(32)

B Offset 0~64(32)

Exit

SDI Audio

Group 1
Group 2
Group 3
Group 4

Auto

Off

Factory Reset Yes

Information

Input/Output &

Revision　

6

7.1 Display



Output: There are NTSC & PAL available for user’s selection.



Size: Adjust the display’s screen size from Full, Over Scan, Under Scan,

Letter box or Pan scan to t the different timing’s display and make the

viewing become more pleasure.

7.2 Color



Adjust screen color RGB’s Contrast and or Brightness.

7.3 SDI Audio

7



Select SDI audio output from 4 different group and each group contents

2CH. If no audio output is require the audio can also be mute by
selecting off.

7.4 Factory Reset



Select YES to return to the factory setting. Factory setting on display is at

1024 x 768@60Hz with full size screen, Color setting's factory default rate

are as the value in the bracket of the OSD chart and SDI audio is on auto.

7.5 Information



Displaying both input source and output display timing with software

version.

8

8. Connection and Installation

SDI Monitor/Display

Camcorder

TV/Display with

CV/SV

Amp

9

Acronyms

A

Acronym Complete Term

3G Bandwidth 2.97G bps ≈ 3G
SDI Serial Digital Interface

10

20110127 MPM-CLUXSDI2CSS

Home page: http://www.cypress.com.tw

CYPRESS TECHNOLOGY CO., LTD.