Cypress CIR-12, CIR-03 Operation Manual

CIR-03 Infrared

Extender Box

and CIR-12 Infrared

Repeater

Operation Manual

CIR-03 & CIR-12

CIR-03 & CIR-12

Disclaimers

The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes
no commitment to update or to keep current the information
contained in this document.
Cypress Technology reserves the right to make improvements to this

document and/or product at any time and without notice.

Copyright Notice

No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means

- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.

© Copyright 2009 by Cypress Technology.
All Rights Reserved.
Version 1.0 July 2009

Trademark Acknowledgments

All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

Safety Precautions

Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:



Always follow basic safety precautions to reduce the risk of

re, electrical shock and injury to persons.



To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.



Never spill liquid of any kind on or into this product.



Never push an object of any kind into this product through

module openings or empty slots, as you may damage parts.



Do not attach the power supply cabling to building surfaces.



Do not allow anything to rest on the power cabling or allow it to

be abused by persons walking on it.



To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.

Revision History

Version No Date Summary of Change

V1 20090701 Preliminary Release

Table of Contents

1

1

1

1

1

2

3

3

3

4

4

4

4

4

5

1. Introduction…………………………………………………........……….

2. Applications……………………..…………………………................….

3. Contents……………………………………………….........................…

4. System Requirement…………………………..….…………........…….

5. Features…………………………………………….......……........………

6. Specications..………………………………………...........………...….

7. Operation Controls and Functions………………...……........………

7.1 Front Panel ..............................................................................

7.2 Rear Panel ………………………………………….........…….…

8. IR Cable Pin Denition............................…………...……........………

9. 3.5Ø Connectors Pin Denition........................................................

9.1 IR IN Pin Denition ...................................................................

9.2 IR OUT Pin Denition ................................................................

9.3 RJ-45 Pin Denition ..................................................................

10. Connection and Installation …….…………………..........……..…...

1. Introduction

The IR Extender and the Repeater Box are two perfect devices for controlling
source equipments over long distance. Through the built-in IR receiver of
IR Repeater and CAT5 cable, users are able to control up to ve source
equipments at the same time that can reach up to a distance of 250 meters
with existing remote controls. There is no space limitation with the devices,
which means even if the source equipments are placed in a different room
or different floor from the display, the performance stays the same. The IR
extender and the repeater box grant users a great convenience, allow users to
control and display their desired source instantly. If however, users only wish to
control the sources within a room area then the IR Repeater Box will be enough
to control up to 2 sources.IR Extender Box is design for long distance and extra
sources control over IR Repeater Box.

2. Applications



TV exhibitions at consumer electronic stores



Home theater installation



Lecture room display



Home entertainment

3. Contents



Infrared Extender Box (CIR-03)



Infrared Repeater Box (CIR-12)



1pc IR Eye Receiver cable (CIR-12)



5pcs IR Eye blaster cables (3pcs for CIR-03, 2pcs for CIR-12)



1pc 5V DC power supply adaptor (for CIR-12)



Operation Manual

4. System Requirement

Input source equipments connected with output displays through CAT 5 cable.

5. Features



Support ve(5) outputs (3 from CIR-03, 2 from CIR-12).



Control source equipments anywhere within 250 meters, piercing through

walls and ceilings.



Transmits infrared signals only.



It allows the use of existing remote controls.



Only one IR Receiver is needed.



IR Receiver's frequency is at 20~60 KHz.

1

Input Port 1 x IR receiver (CIR-12)
Output Ports 1 x CAT5 (CIR-03, CIR-12)

5 x IR extender (3 x CIR-03, 2 x CIR-12)

Power Supply 1 x 5V/1A DC (US/EU standards, CE/FCC/UL certied)

ESD Protection Human body model: ± 10kV (air-gap discharge)

±

6kV (contact discharge)

Dimensions (mm) 62(W) x 50(D) x 23(H)/each
Weight(g) 78/each
Chassis Material Aluminum
Silkscreen Color Silver
Operating Temperature 0°C ~ 40°C / 32°F

~104°F
Storage Temperature -20°C~60°C / -4°F~140°F
Power Consumption 0.5w
Relative Humidity 20~60%RH (non-condensing)

6. Specications

2

②

IR IN: Connect to IR Eye receiver cable each at 2M long for receiving IR

remote control signal.

Note:

Please be very careful when plugging in the blaster and receiver

cables. Wrong connection may damage or burn both cable and device.

7. Operation Controls and Functions

7.1 Front Panels

①

IR CAT5: Connect CAT 5 cable to next Infrared Extender Box with IR

receiver.

②

Power: Plug the 5VDC power supply into the unit and connect the

adaptor to an AC wall outlet.

Note:

Only one power adapter is required for both devices to work.

Connect the power adapter to the IR Repeater Box.

7.2 Rear Panels

①

IR OUT1, 2 and 3: Connect your IR Eye Blaster cables each at 2M long to

control source equipments.

Max.Length 250 Meters

CAT5 Cable

AC Outlet

R Repeater

R Extender

IR N

IR OUT1

IR OUT2

IR Receiver

IR Repeater

IR OUT1

IR OUT2

IR OUT3

IR Extender

IR OUT1

CIR-03 IR Extender

IR OUT2I R OUT3

IR IN

CIR-12 IR Repeater

IR OUT1I R OUT2

1

2

IR CAT5

DC 5V

3

8. IR Cable Pin Denition

IR Blaster IR Receiver

①②

①

Power 5V

②

Power 5V

③

IR blaster signal

①

IR signal

②

Power 5V

③

Grounding

① ② ③

9. 3.5Ø Connectors Pin Denition

9.1 IR IN Pin Denition

Pin Assignment

1 Power 5V
2 IR Signal
3 GND

9.2 IR OUT Pin Denition

Pin Assignment

1 Power 5V
2 Power 5V
3 IR Blaster Signal

9.3 RJ-45 Pin Denition

Pin Assignment

1 GND
2 GND
3 GND
4 IR Blaster Signal
5 IR Blaster Signal
6 GND
7 Power
8 Power

③

4

10. Connection and Installation

IR CAT5

CIR-12

CIR-03

7m

3m

3m

3m

3m

3m

Rear Panel

Rear Panel

Front Panel

DVD

Matrix

Blue Ray

DVD

Front Panel

Note: A. IR receiver's control distance can reach up to 7 meters long with

open space and direct angle.

B. IR extender's control distance can reach up to 3 meters with open

space and direct angle.

5

Acronyms

A

Acronym Complete Term

CAT5 Category 5 Cable

IR Infrared

DC Direct Current

GND Ground

6

7

20081202 MPM-CIR03

Home page: http://www.cypress.com.tw

CYPRESS TECHNOLOGY CO., LTD.