CYPRESS CH-506TXL, CH-506RXL User Manual

CH-506TXL & RXL

HDBaseT™ Lite HDMI over Single CAT5e/6/7 Extender

Operation Manual

Operation Manual

DISCLAIMERS

The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.

Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.

Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means—

electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise—without express written permission and consent from

Cypress Technology.

© Copyright 2011 by Cypress Technology.

All Rights Reserved.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this
equipment:

• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.

• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE

VR0 12/12/11 Preliminary release

VS1 26/04/12 Updated format, diagrams and

statements

VS2 26/07/12 IR cable updated

VR3 28/09/12 Add HDBaseT Lite version

VR4 10/04/14 HDMI I/O cable distance

VR5 13/03/14 IR cable quantity

VR6 28/04/15 Supported resolution

CONTENTS

1. Introduction ............................................ 1

2. Applications ........................................... 1

3. Package Contents ................................ 1

4. System Requirements ............................ 1

5. Features .................................................. 2

6. Operation Controls and Functions ....... 3

6.1 Transmitter Front and Rear Panels .. 3

6.2 Receiver Front and Rear Panels ..... 4

6.3 D-Sub 9-Pin Denitions .....................5

6.4 IR Cable Pin Assignment..................5

7. Connection Diagram ............................ 6

8. Specications ........................................ 7

9. Acronyms ............................................... 8

1. INTRODUCTION

This HDBaseT™ HDMI over Single CAT5e/6/7 Transmitter and Receiver
Set can send uncompressed audio/video over a single run of

CAT5e/6/7 cable up to 60m (1080p) and has the added benet of

control through the built-in RS-232 and 2-way IR.

2. APPLICATIONS

• Domestic HDMI installation

• University lecturing systems

• Retail showroom systems

• Conference presentation and control

3. PACKAGE CONTENTS

• 1×HDMI over Single CAT5e/6/7 Transmitter

• 1×HDMI over Single CAT5e/6/7 Receiver

• 1×IR Blaster

• 1×IR Extender

• 1×3.5 mm Mini-jack to RS-232 Female Cable

• 1×3.5 mm Mini-jack to RS-232 Male Cable

• 2×5 V/2.6 A DC Power Adaptor

• 1×Operation Manual

4. SYSTEM REQUIREMENTS

HDMI source equipment such as a DVD or Blu-ray player and HDMI
equipped display (TV or monitor). HDMI and CAT5e/5/7 connection
cables.

1

5. FEATURES

• HDMI including 3D and 4K2K (Ultra HD) support, HDCP and DVI

compliant

• Supports HDCP repeater and CEC functions

• Simultaneous transmission of uncompressed data over a single

CAT5e/6/7 cable up to 60 m/196 ft (1080p@60 Hz/8-bit), 40m (3D) or

20m (4K2K)

• Supports HD resolutions up to 1080p@60Hz/36-bit and Ultra HD (4K2K)

• Audio support up to LPCM 7.1CH, Dolby TrueHD and DTS-HD Master

Audio

• Supports HDBaseT Lite Technology including 2-way IR and RS-232

• Installation friendly

Note: This system was tested with CAT6/23AWG cable. Results may

vary with cables of different specications.

2

6. OPERATION CONTROLS AND FUNCTIONS

RearFront

7

1

2

3

4

5

6

7

8

6.1 Transmitter Front and Rear Panels

DC 5V

546

Power

Link

Lite

CAT 5e /6 Out

8

RS232 In

IR2 Extender

2

HDMI In

IR1 Blaster

31

RS232 In: Connect to a PC/laptop or RS-232 enabled device

(with supplied 3.5 mm mini-jack to D-sub 9-pin adaptor) for the
transmission of RS-232 commands.

IR2 Extender: Connect to the supplied IR extender cable for IR

signal reception. Ensure that remote control being used is within

the direct line-of-sight of the IR extender.

IR1 Blaster: Connect to the supplied IR blaster cable for IR signal

transmission. Place the IR blaster in direct line-of-sight of the
equipment to be controlled.

HDMI In: Connect to the HDMI source equipment such as a DVD or

Blu-ray player.

DC 5V: Connect the 5 V DC power supply to the unit and plug the

adaptor into an AC outlet.

Link LED: The yellow LED will illuminate when both the input and

output CAT5e/6/7 signals are connected.

Power LED: This green LED will illuminate when the device is

connected to a power supply.

CAT5e/6 Out: Connect to the receiver unit with a single CAT5e/6/7

cable for transmission of all data signals.

3

6.2 Receiver Front and Rear Panels

RearFront

7

1

2

3

4

5

6

7

8

IR1 Extender

RS232 Out

2

HDMI Out

IR2 Blaster

31

DC 5V

546

Power

Link

Lite

CAT 5e /6 In

8

RS232 Out: Connect to the device that is to be controlled (with

the supplied 3.5mm mini-jack to D-sub 9-pin adaptor) by RS-232
commands.

IR1 Extender: Connect to the supplied IR extender cable for IR

signal reception. Ensure that the remote being used is within the

direct line-of-sight of the IR extender.

IR2 Blaster: Connect to the supplied IR blaster cable for IR signal

transmission. Place the IR blaster in direct line of sight of the
equipment to be controlled.

HDMI Out: Connect to a HDMI equipped TV/monitor for display of

the HDMI input source signal.

DC 5V: Plug the 5 V DC power supply into the unit and connect the

adaptor to an AC outlet.

Link LED: The yellow LED will illuminate when both the input and

output CAT5e/6/7 signals are connected.

Power LED: This green LED will illuminate when the device is

connected to a power supply.

CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6/7

cable for transmission of all data signals.

4

6.3 D-Sub 9-Pin Denitions

PIN DEFINE TX/RX

1 N/C

2 TxD/RxD

3 RxD/TxD

4 N/C

5 GND

6 N/C

7 N/C

8 N/C

9 N/C

6.4 IR Cable Pin Assignment

IR Blaster

1

2

3

Power

IR Signal

NC

5

IR Extender

1

IR Signal

2

Power

3

Grounding

7. CONNECTION DIAGRAM

m

3m

DVD/Blu-ray Player

1.5m

7m

3m 3m

60°

IR Extender 2

60°

IR Blaster 1

RS232 In

RS-232 Equipped

PC or Notebook

HDMI
Input

RS-232

IR2 Extender

HDMI In

IR1 Blaster

DC 5V

TX

Power

Link

CAT 5e/6 Out

IR Extender 1

60°

3m

7m

Power Supply

Power Supply

IR Blaster 2

60°

1.5m

Display

DC 5V

Power

Link

IR1 Extender

RS232 Out

CAT5e/6/7
Cable (60m)

CAT 5e/6 In

RX

HDMI Out

IR2 Blaster

HDMI

Output

RS-232

RS-232 Device to

be Controlled

6

8. SPECIFICATIONS

Video Bandwidth 340 MHz/10.2 Gbps

Transmitter

Input Ports 1×HDMI, 1×IR Extender, 1×RS-232

Output Ports 1×CAT5e/6/7, 1×IR Blaster

Receiver

Input Ports 1×CAT5e/6/7, 1×IR Extender

Output Ports 1×HDMI, 1×IR Blaster, 1×RS-232

CAT5e/6/7 Cable

Distance

HDMI Cable Input

Distance

HDMI Cable Output

Distance

ESD Protection Human-body Model:

Power Supply 5 V/2.6 A DC (US/EU standards, CE/FCC/UL

IR Frequency 30~50 kHz

Dimensions 71 mm (W)×79 mm (D)×23 mm (H)/Each

Weight 240 g/TX, 245 g/RX

Chassis Material Aluminum

Color Black

Operating Temperature 0°C~40°C/32°F~104°F

Storage Temperature −20°C~60°C/−4°F~140°F

Relative Humidity 20~90 % RH (non-condensing)

Power Consumption 3 W/TX, 6 W/RX

Up to 60 m

10 m@8-bit, 6 m@12-bit

10 m@8-bit, 6 m@12-bit

±8 kV (air-gap discharge)

±4 kV (contact discharge)

certied)

7

CAT5e/6/7 Cable Specication:

LENGTH BANDWIDTH DATA RATE SUPPORTED VIDEO

Up to

60 m

Up to

35 m

Up to

225 MHz

Greater

than

225 MHz

Up to

5.3 Gbps

Greater

than

5.3 Gbps

HD Video

Up to 1080p@60 Hz/36-bit, 3D

(data rate lower than 5.3 Gbps

or bandwidth below 225 MHz).

Ultra HD Video

Up to 4K×2K@30 Hz.

9. ACRONYMS

ACRONYM COMPLETE TERM

CAT5e Category 5 Cable

CAT6 Category 6 Cable

CAT7 Category 7 Cable

CEC Consumer Electronics Control

DVI Digital Visual Interface

HDCP High-bandwidth Digital Content Protection

HDMI High Denition Multimedia Interface

IR Infrared

8

CYPRESS TECHNOLOGY CO., LTD

Home page: http://www.cypress.com.tw