CYP SY-12H-4K22 Operation Manuals
SY-12H-4K22
4K UHD (HDR10 6G) 1 in 2 out HDMI Dual Scaler
OPERATION MANUAL
3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 20/06/2018 First release
5
CONTENTS
1. Introduction ...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................7
5. Features ..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel ................................................... 8
6.2 Rear Panel ..................................................... 9
6.4 RS-232 Control .......................................... 22
6.5 RS-232 Commands .................................. 23
7. Connection Diagram .......................... 36
8. Specifications ...................................... 37
8.1 Technical Specifications ........................37
8.2 Video Specifications................................38
8.3 Audio Specifications ............................... 41
8.4 Cable Specifications ...............................41
9. Acronyms ............................................. 42
6
1. INTRODUCTION
This HDMI 4K UHD Scaler with Test Patterns and Signal Event Automation
is designed to upscale 1080p signals into 4K UHD (18Gbps) or downscale
4K UHD (18Gbps) signals into 1080p with synchronised digital audio
output. A friendly and simple interface design allows the user to control
the unit while viewing the OSD directly on the HDMI outputs. The input
signal can be output to both HDMI outputs simultaneously with a
dierent resolution on each or the unit can generate a test pattern at a
preferred video resolution for easy on-site display testing and validation.
Additional functionality such as EDID and HDCP management, and basic
signal event automation (via RS-232 or CEC) is also provided. This UHD
Scaler is the best tool to use with your HD and UHD signals. This unit can
be controlled easily by use of the front panel controls (with OSD) or by
RS-232.
2. APPLICATIONS
HDMI signal splitting
On-site equipment testing
Production testing
R&D design and testing
3. PACKAGE CONTENTS
1×HDMI to Dual HDMI Scaler
1×5V/2.6A DC Power Adapter
2×3-pin Terminal Block to 9-pin D-sub Adapter Cable
1×Shockproof Feet (Set of 4)
1×Operation Manual
7
4. SYSTEM REQUIREMENTS
HDMI input source equipment such as a media player, video game
console or set-top box.
HDMI receiving equipment such as HDTVs, monitors or audio
amplifiers.
The use of “Premium High Speed HDMI” cables is highly
recommended.
5. FEATURES
HDMI input and output with 18Gbps (600MHz) 4K UHD with HDR
support
DVI 1.0 compliant with the use of an HDMI-DVI adaptor
HDCP 2.2 and HDCP 1.x compliant
1 HDMI input and 2 HDMI outputs
Supports HDCP 2.2 to HDCP1.4 conversion
HDMI signal bypass on both outputs or upscales 1080p signals to 4K
on output B and downscales 4K signals to 1080p on output A
Supports HD resolutions up to 3840×2160@60Hz (4:4:4, 8-bit)
Supports 4K HDR at 24/30Hz (YUV 4:4:4) and 50/60Hz (YUV 4:2:0) with
up to 12- bit colour
Supports 16-bit Deep Colour up to 1080p@60Hz
Supports pass-through of many audio formats including LPCM
2.0/5.1/7.1, Bitstream, and HD Bitstream
Supports colour space conversion of 4K@50/60Hz (4:4:4, 8-bit) or
4K@any (10/12-bit) sources
Integrated EDID and HDCP management
Basic signal event automation (via RS-232 or CEC)
Test pattern generation at selected resolutions for on-site display
testing
Controllable via front panel with OSD, and RS-232
8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
SERV.
POWER 4K2K SYNC MENU PATTERN
TEST
ENTER
-
+
1 2 3 4 5 6 7
SY-12H-4K22
1
SERV.: This slot is reserved for firmware update and EDID upload use
only.
2
POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
3
4K2K LED: This LED will illuminate when the input source contains a
4K UHD signal.
4
SYNC LED: This LED will illuminate when the input source is sending
signal.
5
MENU Button: Press to enter the OSD menu, or to back out from
menu item.
6
− & +/TEST PATTERN Buttons: When the OSD menu is in use,
press these buttons to move within the menu. Outside of the OSD,
press these buttons together to instantly set the output timing to
1280x720@60Hz and display test patterns on both outputs.
7
ENTER Button: Press to confirm a selection within the OSD or to go
deeper into a menu item.
9
6.2 Rear Panel
HDMI IN HDMI OUT RS-232
DC 5V
A B
OUT
IN
1 2 3 4
1
HDMI IN: Connect to HDMI source equipment such as a media player,
game console or set-top box.
2
HDMI OUT A~B: Connect to HDMI TVs, monitors or amplifiers for
digital video and audio output. Each output can display a different
resolution with a choice between the HDMI source or a test pattern.
3
RS-232: Connect the upper 3-pins directly to a PC, laptop or other
serial control device to send RS-232 commands to control the unit.
Connect the lower 3-pins directly to a serial controllable device to
send signal event automation RS-232 commands to it.
4
DC 5V: Plug the 5V DC power adapter into the unit and connect it to
an AC wall outlet for power.
10
6.3 OSD Menu
All primary functions of this unit can be controlled by using the OSD
(On Screen Display) which is activated by pressing the Menu button on
the front of the unit. Use the + (PLUS), − (MINUS), and ENTER buttons to
navigate the OSD menu. Press the Menu button to back out from any
menu item and then press it again to close the menu.
MAIN MENU STRUCTURE
Output
EDID
HDCP
OSD
Test Pattern A
Test Pattern B
Information
Firmware Update
EDID Upload
Factory Setting
The individual functions of the OSD will be introduced in the following
section. Items marked in BOLD are the factory default settings.
11
OUTPUT
2nd Level 3rd Level
Output A
Input 4K2K PASS THROUGH
Down Scaler 1080P
Fix Colour YUV 4:2:0
Fix Deep Colour 8 bit
YUV 4:2:x to RGB
Fix Colour RGB
Output B
Input 1080P PASS THROUGH
Input 1080P Up Scaler 4K2K
Up Scaler 4K2K YUV 4:2:0
Input 4K2K PASS THROUGH
Fix Colour YUV 4:2:0
Fix Deep Colour 8 bit
YUV 4:2:x to RGB
Fix Colour RGB
Up 4K2K Scaler Enhancement
Gain Level 1 (Weak)
Level 2
LEVEL 3
Level 4
Level 5
Level 6 (Strong)
12
Output A
1) Input 4K2K: Controls the scaling of 4K sources on Output A.
■ Pass Through: Will pass all 4K sources without modification.
■ Down Scaler 1080P: Will convert all 4K sources to 1080P at the
same frame rate as the original.
■ Fix Colour YUV 4:2:0: Will convert 4K@50/60 (4:4:4) sources to the
YUV 4:2:0 colour space.
■ Fix Deep Colour 8 bit: Will reduce any 4K sources with a bit depth
above 8-bit to 8-bit colour.
■ YUV 4:2:x to RGB: Will convert any 4K source using the YUV 4:2:2
or 4:2:0 colour space to the RGB colour space.
■ Fix Colour RGB: Will convert any 4K source using the YUV colour
space to the RGB colour space.
Output B
2) Input 1080P: Controls the scaling of 1080P sources on Output B.
■ Pass Through: Will pass 1080p sources without modification.
■ Up Scaler 4K2K: Will scale all 1080p sources to 4K(4:4:4) at the
same frame rate.
■ Up Scaler 4K2K YUV 4:2:0: Will scale all 1080p@50/60Hz sources
to 4K(4:2:0) at the same frame rate.
3) Input 4K2K: Controls the scaling of 4K sources on Output B.
■ Pass Through: Will pass all 4K sources without modification.
■ Fix Colour YUV 4:2:0: Will convert 4K@50/60 (4:4:4) sources to the
YUV 4:2:0 colour space.
■ Fix Deep Colour 8 bit: Will reduce any 4K sources with a bit depth
above 8-bit to 8-bit colour.
■ YUV 4:2:x to RGB: Will convert any 4K source using the YUV 4:2:2
or 4:2:0 colour space to the RGB colour space.
■ Fix Colour RGB: Will convert any 4K source using the YUV colour
space to the RGB colour space.
Up 4K2K Scaler Enhancement
1) Gain: Provides control over the aggressiveness of the digital gain
processing when applied to the scaled output image.
13
EDID
2nd Level
INTERNAL FHD 2CH
Internal FHD 8CH
Internal UHD 2CH
Internal UHD 8CH
Internal UHD+ 2CH
Internal UHD+ 8CH
User
Sink Output A
Sink Output B
1) EDID: Select the EDID to use with the HDMI input.
HDCP
2nd Level
HDCP Support Off
Reference to Source
REFERENCE TO DISPLAY
1) HDCP: Selects the HDCP logic to use with the HDMI input.
14
OSD
2nd Level 3rd Level
Display Information ON
Off
OSD Timeout Off
5 SEC.
10 Sec.
15 Sec.
20 Sec.
25 Sec.
30 Sec.
35 Sec.
40 Sec.
1) Display Information: Enable or disable the informational OSD.
2) OSD Timeout: Set the length of time to wait before automatically
turning off the OSD menu if there is no user interaction. The timer may
also be disabled.
Loading...