CYmodel P-47 Instruction Manual

SAFETY PRECAUTIONS

This radio control model is not a toy!

lFirst-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent.

,

lAssemble this kit only in places out of childrens reach! lTake enough safety precautions prior to operating this model.

,

You are responsible for this models assembly and safe operation! lAlways keep this instruction manual ready at hand for quick reference,even after completing the assembly. lCould cause serious injury or even death

SPECIFICA TION

Wing Span: 2400mm (96in)

2

Wing Area: 92.3dm (1431sq.in) Total Length: 2120 mm (83.5 in) Engine :100-150cc gas engine Radio : 6 channels ,9 servos

P-47

ALMOST - READY - TO - FLYALMOST - READY - TO - FLY

Before commencing assembly,please read these instructions thoroughly.

Thank you for choosing CYmodel

Global : www.cymodel.com

Australia : www.austars-model.com Italia : www.biellaexpress.com

Instruction Manual

Item Nr: CY8009

REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately)

TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)

BEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGIN

Sharp Hobby Knife

Phillips Screw Driver

Awl

Needle Nose Pliers

Wire Cutters

Scissors

Read through the manual before you begin ,so you will have an overall idea of what to do.

Check all parts .if you find any defective or missing parts .contact your local deater.

Symbols used throughout this instruction manual,comprise.

111 222

333

.

Warning!

!

Do not overlook this symbol.

A minimum 6channel radio for airplanes (with 9servos). And dry batteries.

CAUTION: Only use a minimum 6channel radio for airplanes! (No other radio may be used!)

!

12 AA-size Batteries

A minimum 6 channel

transmitter for airplanes.

For handing the radio properly.refer to its instruction manual.

Engine and Muffler

Purchase a propeller that will match your engine

Silicone Tube

Fuel Filter

required for engine starting

Glow engine fuel only.

WARNING: Normal gasoline cannot

be used with glow engines.

!

Fuel Pump

Plug Wrench

Glue

Instant glue

Epoxy Glue

Other equipment for enhancing

airplane operation & perormance

12V Battery (for starter)

Engine Starter

B B B B

22

Cut off shaded portion.

Ensure smooth non-binding movement while assembling.

Must be purchased separately!

Pay close attention here!

Drill holes with the specified Diameter(here:2mm)

Assemble left and right Sides the same way.

Apply instant glue

(CA glue,super glue).

Apply epoxy glue.

Cut off excess.

502

C.AC.A

LL

RR

A B

2mm2mm

99

44

11

77

66

55

88

Model Airplane engine:100-150cc gas engine

receiver

22

Battery (need 2)

33

Servo(need 9 servos )

remote control

Switch (need 2)

Muffler

!

3

2

1

5

4

33

Install the aileron and flap

Install the servo of aileron

Install the servo

Aileron

Flap

Hinge

Install the aileron and flap

Bottom view

Install the servo of flap

Hinge

Accessory list for this page.

LL

RR

LL

RR

Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents!

Warning!Warning!

Rod adjuster

Connecting rod head

3X30mm screw

2X8mm screw

- - - - - 4

- - - - - 2

- - - - - 6

- - - - - 4

2.5X85mm rod

- - - - - 2

HORN

- - - - - 2

4X30 Screw

- - - - - 2

LL

RR

FlapAileron

A B

- - - - - - - - 8

A B

Make sure hinges are mounted in the same line

3mm3mm

2.3X10mm Tp screw

- - - - - 8

LL

RR

Rod adjuster

Connecting rod head

3X12mm TP screw

2X8mm screw

- - - - - 4

- - - - - 2

- - - - - 6

- - - - - 4

2.5X85mm rod

- - - - - 2

HORN

- - - - - 2

4X30 Screw

- - - - - 2

2.3X10mm Tp screw

- - - - - 8

Flap

Aileron

Tailing edge

Aileron

4mm

Servo line

Rod adjuster

Connecting rod head

3X30mm screw 2X8mm screw

- - - - - 8

- - - - - 4

- - - - - 6

- - - - - 8

2.5X85mm rod

- - - - - 4

HORN

- - - - - 4

- - - - - 2

4X30 Screw

- - - - - 4

2.3X10mm Tp screw

- - - - - 16

- - - - - - - - 8

- - - - - 8

LL

RR

Servo line

3X12mm TP screw

- - - - - 6

!

8

7

6

10

9

44

Accessory list for this page.

Install the elevator

LL

RR

Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents!

Warning!Warning!

LL

RR

Rod adjuster

Connecting rod head

3X30mm screw

2X8mm screw

- - - - - 4

- - - - - 2

- - - - - 6

- - - - - 4

2.5X85mm rod

- - - - - 2

HORN

- - - - - 2

4X30 Screw

- - - - - 2

Bottom view

Install the elevator

make sure hinges are mounted in the same line

A B

Hinge

- - - - - - - - 8

Install the elevator servos

LL

RR

LL

RR

LL

RR

3mm 3mm

LL

RR

Install the rudder

make sure hinges are mounted in the same line

Hinge

- - - - - - - 4

A B

Hinge

- - - - - - 12

Rod adjuster

Connecting rod head

3X30mm screw

2X8mm screw

- - - - - 4

- - - - - 2

- - - - - 6

- - - - - 4

2.5X85mm rod

- - - - - 2

HORN

- - - - - 2

4X30 Screw

- - - - - 2

!

13

12

15

1414

55

11

Accessory list for this page.

Install the rudder servos

Install the rudder

Install the tail wheel

Aluminium tube

Rod adjuster

2X8mm screw

- - - - - 2

Rod

- - - - - 2

Install the servos of rudder&tail wheel

Install the tail wheel

Securely glue together. If coming off during flights,you'll lose control of your airplane which leads to accidents!

Warning!Warning!

Tailing edge

Rudder

4mm

A B

Aluminium tube

Rod adjuster Connecting rod head

2X8mm screw

- - - - - 2

Rod

- - - - - 2

5mm nut

- - - - - 2

1400mm Steel wire

- - - - - 2

- - - - 1

- - - - 2

3.2mm Collar

3.2mm Nylon Collar

3X3mm Screw

- - - - 3

6X9 screw

- - - - 1

M3X20 Tp screw

3.2mm Rocker

- - - - - 1

6mm nut

80mm spring

- - - - - 2

5X100mm screw

- - - - - 1

Aluminium tube

Rod adjuster

Connecting rod head

2X8mm screw

- - - - - 4

- - - - - 2

- - - - - 4

Rod

- - - - - 4

5mm nut

- - - - - 2

1400mm Steel wire

- - - - - 2

5X100mm screw

- - - - - 1

- - - - 1

- - - - 2

3.2mm Collar

3.2mm Nylon Collar

3X3mm Screw

- - - - 3

6X9 screw

- - - - 1

M3X20 Tp screw

3.2mm Rocker

- - - - - 1

6mm nut

80mm spring

- - - - - 2

!

18

17

20

19

16

66

Accessory list for this page.

Install the main landing gear

Main wing

(Put the servo into the fuselage)

LL

RR

LL

RR

5

0

2

C.A

Air tank

Switch

Air inlet

3-way pressure inlet

Quick release connector

Pressure reduction inlet

Strut

Pleas notice the inner diameter for each side of the pressure reduction inlet.

Please insure the sealing of the retract system before flight .

Install the main landing gear

After glue the PVC cover, cut off its excess part.

Install the main landing gear

A B

3X3mm screw

5.2mm Collar

3X20mm Tp screw

- - - - - 8

5X45mm Axletree

- - - - - 2

4X4mm screw

- - - - - 2

Play wood

- - - - - - - - - - - -2

- - - - - - - - - - - -4

Retainer

Rod adjuster

2X8mm screw

- - - - - 1

Rod (1.8X80mm)

- - - - - 1

900 Air line

- - - - - 2

LL

RR

8mm nylon Nut

- - - - - 4

3X3mm screw

5.2mm Collar

3X20mm Tp screw

- - - - - 8

5X45mm Axletree

- - - - - 2

4X4mm screw

- - - - - 2

8mm nylon Nut

- - - - - 4

Retainer

Rod adjuster

2X8mm screw

- - - - - 1

Rod (1.8X80mm)

- - - - - 1

900 Air line

- - - - - 2

Play wood

- - - - - - - - - - - -2

- - - - - - - - - - - -4

!

23

25

77

21 24

22

Accessory list for this page.

Horizontal

(Put the servo into the fuselage)

Main wing&Horizontal/Vertical tail

Securely glue together ,if coming off during flights. You lose control of your airplane which leads to accidents!

A A B

B

C

4mm4mm

4X25mm screw

4mm Washer

- - - - - - - - 2

- - - - 2

A

B

C

Installing the engine (100-150cc)

After confirming the position(see front of fuel tank). Insert and tighten the screw.

Fuel supply line

Fuel pipe

Air pressure line

1.8X200mm Rod

- - - - - - 1

Linkage Stopper

2mm Nut

- - - - 1

3X3mm Screw

- - - - - - 1

Install the throttle servo

Assembly of the full t ank

175mm

ThrottleThrottleFuel tankFuel tank

1.8X200mm Rod

- - - - - - 1

Linkage Stopper

2mm Nut

- - - - 1

3X3mm Screw

- - - - - - 1

4X25mm screw

4mm Washer

- - - - - - - - 2

- - - - 2

3mm3mm

Playwood

Cowling

!

28

27

30

29

88

26

Accessory list for this page.

Radio Equipment

Install the thr cowling

Receiver Receiver

BatteryBattery

Battery/IgnitionBattery/Ignition

Install the canopy

Install the thr cowling

SpinnerSpinner

PropellerPropeller

3mm Bind nut

3mm Washer

- - - - - 6

3X16mm screw

- - - - - 6

3mm rubber band

- - - - 6

3mm Washer

- - - - - 2

3X30mm screw

- - - - - 2

3mm rubber band

- - - - 2

A B

6mm Playwood

3X30mm screw

- - - - - 2

3mm Bind nut

3mm Washer

- - - - - 6

- - - - - 8

3X16mm screw

- - - - - 6

3mm rubber band

6mm Playwood

- - - - 6

- - - - - 6

- - - - - 8

2.3X10mm Tp screw

- - - - - 6

2.3X10mm Tp screw

- - - - - 6

33

32

34

Side view

ELEV A TOR

Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level.

Top view

31

AILERON

Adjustment.

Top view

Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level.

99

Adjustment.

Never fly before checking the Cg s required position. In order to obtain the CG specified ,reposition the

receiver and battery.

NEVER fly the model without well balancing.

Warning!

!

CG

Side view

Rudder

Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level.

Top view

155-165mm155-165mm

Adjustment

Side view

Adjustment.

45

Flap

45