SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
,
lAssemble this kit only in places out of childrens reach!
lTake enough safety precautions prior to operating this model.
,
You are responsible for this models assembly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
SPECIFICA TION
Wing Span: 2540mm (100in)
2
Wing Area: 94.5dm (1463.5sq.in)
Total Length: 2000 mm (78.7 in)
Engine :80cc gas engine
Radio : 5-6 channels ,10 servos
Ju87 stukaJu87 stuka
ALMOST - READY - TO - FLYALMOST - READY - TO - FLY
Before commencing assembly,please read these instructions thoroughly.
Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Item Nr: CY8018
REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGIN
Sharp Hobby Knife
Phillips Screw Driver
Awl
Needle Nose Pliers
Wire Cutters
Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!
!
Do not overlook this symbol.
A minimum 5-6channel radio for airplanes (with10servos).
And dry batteries.
CAUTION: Only use a minimum 5-6channel radio for
airplanes! (No other radio may be used!)
!
12 AA-size Batteries
A minimum 6 channel
transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller that
will match your engine
Silicone Tube
Fuel Filter
required for engine starting
Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump
Plug Wrench
Glue
Instant glue
Epoxy Glue
Other equipment for enhancing
airplane operation & perormance
12V Battery (for starter)
Engine Starter
B B B B
22
Cut off shaded portion.
Ensure smooth non-binding
movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right
Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
5
02
C.AC.A
LL
RR
A B
2mm2mm
99
44
11
77
66
55
88
Model Airplane engine:80cc gas engine
receiver
22
Battery (need 2)
33
Servo(need 10 servos )
remote control
Switch (need 2)
AA
Muffler
Ignition
!
3
2
1
5
4
33
Install the flap
Install the servo
Bottom view
Install the main landing gear
Install the aileron and flap
Install the aileron
Bottom view
Accessory list for this page.
LL
RR
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
Warning!Warning!
LL
RR
A B
A B
LL
RR
A B
A B
LL
RR
A B
Rod adjuster
2X8mm screw
- - - - - 12
- - - - - 12
2.5X100mm rod
- - - - - 6
11
22
15mm plywood
3X3mm screw
5.2mm Collar
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 4
LL
RR
2X190mm Steel wire
2X450mm Steel wire
2X525mm Steel wire
Rod adjuster
2X8mm screw
- - - - - 12
- - - - - 12
2.5X100mm rod
- - - - - 6
3X3mm screw
5.2mm Collar
5X45mm Axletree
- - - - - 2
- - - - - 2
- - - - - 4
!
8
7
6
10
9
44
Accessory list for this page.
LL
RR
A B
4mm4mm
Install the main landing gear
33
Install the main landing gear
44
4mm Lock nut
4mm Washer
4X50mm screw
- - - - - 2
- - - - - 4
- - - - - 2
4mm Lock nut
4X25mm screw
- - - - - 4
- - - - - 4
4X20mm screw
- - - - - 12
LL
RR
LL
RR
8mm Nut
- - - - - 4
Main wing
Main wing
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
A A
B
B
A
A
B
B
25X1005mm tube
20X775mm tube
8mm Nut
- - - - - 4
4X20mm screw
- - - - - 12
4X25mm screw
- - - - - 4
4mm Lock nut
4mm Washer
4X50mm screw
- - - - - 6
- - - - - 4
- - - - - 2
Put the servo line into the fuselage
!
13
12
15
1414
55
11
Accessory list for this page.
Install the rudder
Install the elevator
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
Warning!Warning!
Tailing edge
Elevator
4mm
A B
LL
RR
Install the elevator
make sure hinges are
mounted in the same line
Hinge
- - - - - - - 8
make sure hinges are
mounted in the same line
Hinge
- - - - - - - 3
A B
Warning!Warning!
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
Tailing edge
Rudder
4mm
A B
Install the rudder
4X30mm screw
4mm Washer
- - - - - - - - 4
- - - - 2
LL
RR
LL
RR
4mm Lock nut
- - - - 2
4mm4mm
12X400mm tube
4X30mm screw
4mm Washer
- - - - - - - - 4
- - - - 2
4mm Lock nut
- - - - 2
Hinge
- - - - 11
!
18
17
20
19
16
66
Accessory list for this page.
Install the rudder servo
Aluminium tube
Rod adjuster
2X10mm screw
- - - - - 2
- - - - - 2
Rod
- - - - - 2
- - - - - 2
Aluminium tube
Rod adjuster
Connecting rod head
2X10mm screw
- - - - - 2
- - - - - 2
- - - - - 2
Rod
- - - - - 2
- - - - - 2
3mm nut
- - - - - 6
1000mm Steel wire
- - - - - 2
HORN
- - - - - 2
4X30 Screw
- - - - - 2
3mm3mm
3X40mm screw
- - - - - 3
Install the tail wheel
Securely glue together
,if coming off during flights.
You lose control of your airplane
which leads to accidents!
D D
E
E
C
C
D D
E
E
C
C
Main wing&Horizontal/Vertical tail
- - - - 1
- - - - 2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 3
- - - - 3
6X9 screw
- - - - 1
- - - - 1
M3X20 Tp screw
3.2mm Rocker
- - - - - 1
6mm nut
Install the tail wheel
Install the rudder servo
80mm spring
- - - - - 2
Aluminium tube
Rod adjuster
Connecting rod head
2X10mm screw
- - - - - 4
- - - - - 2
- - - - - 4
Rod
- - - - - 4
- - - - - 4
3mm nut
- - - - - 6
1000mm Steel wire
- - - - - 2
HORN
- - - - - 2
4X30 Screw
- - - - - 2
3X40mm screw
- - - - - 3
- - - - 1
- - - - 2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
- - - - 3
- - - - 3
6X9 screw
- - - - 1
- - - - 1
M3X20 Tp screw
3.2mm Rocker
- - - - - 1
6mm nut
!
23
25
77
21 24
22
Accessory list for this page.
Installing the engine (80cc)
1.8X400mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
Install the throttle servo
ThrottleThrottleFuel tankFuel tank
Install the elevator servo
755mm
2.5X100mm rod 2.5X330mm rod
5X3X380mm carbon rod
- - - - - 2
- - - - - 2
- - - - - 2
A B A B
Install the elevator servo
Install the rod for elevator
Rod adjuster
Connecting rod head
2X10mm screw
- - - - - 4
- - - - - 4
- - - - - 4
HORN
- - - - - 2
4X30 Screw
- - - - - 2
3X25mm screw
- - - - - 6
LL
RR
170mm
Rod adjuster
Connecting rod head
2X10mm screw
- - - - - 4
- - - - - 4
- - - - - 4
HORN
- - - - - 2
4X30 Screw
- - - - - 2
3X25mm screw
- - - - - 6
1.8X400mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
!
28
27
30
29
88
26
Accessory list for this page.
Radio Equipment
Install the thr cowling
Receiver Receiver
Battery/IgnitionBattery/Ignition
Install the canopy
Install the canopy
SpinnerSpinner
PropellerPropeller
3mm Bind nut
3mm Washer
- - - - - 6
- - - - - 6
3X16mm screw
- - - - - 6
3mm rubber band
- - - - 6
A B
6mm Plawood
3X30mm screw
2
3mm Bind nut
3mm Washer
6
8
3X16mm screw
6
3mm rubber band
6mm Plywood
- - - - 6
6
8
3mm3mm
Playwood
Cowling
Cut away the surplus pats
of canopy,care fully along
the shaded line.
2.3X10Tp screw
- - - - - 10
3X30mm Screw
- - - - 2
3mm washer
- - - - 2
3mm rubber band
- - - - 2
2.3X10Tp screw
10
After confirming the
position(see front of
fuel tank).
Insert and tighten
the screw.
Fuel supply line
Fuel pipe
Air pressure line
Assembly of the full tank
33
32
34
Side view
ELEV A TOR
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
31
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
1010
Adjustment.
Never fly before checking the Cg s required position.
In order to obtain th e CG specified ,reposition the
receiver and battery.
NEVER fly the model
without well balancing.
Warning!
!
CG
Side view
Rudder
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Top view
150-160mm150-160mm
Adjustment
Side view
Adjustment.
45
45
45
45
45
Flap
45
45
Loading...