CYmodel CY8016B User guide

Thank you for choosing CYmodel

Global : www.cymodel.com

Australia : www.austars-model.com Italia : www.biellaexpress.com

Fokker D-VIII

Item Nr: CY8016B

Instruction Manual

Before commencing assembly,please read these instructions thoroughly.

ALMOST - READY - TO - FLYALMOST - READY - TO - FLY

SAFETY PRECAUTIONS

This radio control model is not a toy!

lFirst-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent.

lAssemble this kit only in places out of childrens reach! lTake enough safety precautions prior to operating this model.

You are responsible for this models assembly and safe operation! lAlways keep this instruction manual ready at hand for quick reference,even after completing the assembly. lCould cause serious injury or even death

,

SPECIFICATION

Wing Span:2800 mm (110 in) Wing Area:119.7 dm (1856 sq.in) Fuselage Length: 2100 mm (82.5 in) Engine : 80-100cc gas engine Radio : 4 channels ,6 servos

2

REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately)

A minimum 4channel radio for airplanes (with 6servos).

11

And dry batteries.

CAUTION: Only use a minimum 4channel radio for

!

airplanes! (No other radio may be used!)

A minimum 4 channel

transmitter for airplanes.

12 AA-size Batteries

For handing the radio properly.refer to its instruction manual.

Battery (need 2)

22

Servo(need 6 servos )

33

Engine and Muffler

44

Model Airplane engine:80-100cc gas engine

receiver

Switch (need 2)

Muffler

remote control

Glue

55

required for engine starting

66

WARNING: Normal gasoline cannot

!

be used with glow engines.

Fuel Pump

Silicone Tube

77

Other equipment for enhancing

88

airplane operation & perormance

Engine Starter

Purchase a propeller that

99

will match your engine

B B BB

AA

Epoxy Glue

Instant glue

Glow engine fuel only.

Plug Wrench

Fuel Filter

12V Battery (for starter)

20X10----22X10

TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)

Sharp Hobby Knife

Needle Nose Pliers

BEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGIN

111

Read through the manual before you begin ,so you will have an overall idea of what to do.

.

222

Check all parts .if you find any defective or missing parts .contact your local dealer.

.

333

Symbols used throughout this instruction manual,comprise.

A B

C.AC.A

Apply epoxy glue.

02

5

Apply instant glue

(CA glue,super glue).

2mm2mm

Drill holes with the specified Diameter(here:2mm)

Ensure smooth non-binding movement while assembling.

Phillips Screw Driver

Wire Cutters

Awl

Scissors

Must be purchased separately!

Pay close attention here!

Do not overlook this symbol.

!

Warning!

LL

Assemble left and right

RR

Sides the same way.

Cut off shaded portion.

22

Cut off excess.

Accessory list for this page.

!

3

Install the aileron servo

2.6X12mm Tp screw

2X10mm screw

2.5X85mm rod

4X35mm screw

4mm Washer

Hinge

1

Install the aileron

- - - - - 8

- - - - - 4

- - - - - 2

- - - - - 4

- - - - - 10

HORN

- - - - - 2

4X40 Screw

- - - - - 2

Rod adjuster

- - - - - 4

Connecting rod head

- - - - - 2

3X35mm screw

- - - - - 6

LL

RR

LL

RR

4

RR

Install the aileron servo

Make sure hinges are mounted in the same line

2

Install the aileron

Hinge

- - - - - - - - 10

A B

LL

RR

5

4X35mm screw

Main wing

- - - - - 4

Servo line

2.6X12mm Tp screw

2X10mm screw

2.5X85mm rod

4mm Washer

- - - - - 4

32X910mm tube

- - - - - 8

- - - - - 4

- - - - - 2

4mm4mm

3mm3mm

HORN

- - - - - 2

4X40 Screw

Rod adjuster

Connecting rod head

3X35mm screw

- - - - - 2

- - - - - 4

- - - - - 2

- - - - - 6

LL

A B

20X440mm tube

RR

33

Accessory list for this page.

!

4X25mm screw

- - - - - 4

4X35mm screw

- - - - - 3

4mm Washer

- - - - - 7

Hinge

- - - - - - - - 9

Main wing&Horizontal/Vertical tail

8

4X25mm screw

- - - - - 4

4mm Washer

- - - - - 4

6

A B

7

Install the elevator

Install the rudder

Hinge

- - - - - - - - 6

99

10

4X35mm screw

- - - - - 3

4mm4mm

A B

Horizontal/Vertical tail

4mm Washer

- - - - - 3

Hinge

- - - - - - - - 3

A B

44

A

B

Securely glue together ,if coming off during flights. You lose control of your airplane which leads to accidents!

B A

B

B A

Accessory list for this page.

!

13

Install the elevator servo

11

Connecting rod head

- - - - - 4

2.5X125mm rod

3X25mm screw

Rod

1400mm steel wire

Aluminium tube

- - - - - 2

- - - - - 9

- - - - 4

- - - - 2

- - - - - - 4

3mm Lock Nut

- - - - - 3

3X20mm Tp screw

- - - - - -12

HORN

- - - - - 4

- - - - - 2

4X40 Screw

Rod adjuster

2X10mm screw

5.2mm Collar

3X3mm screw

Aluminum plate

- - - - - 4

- - - - - 8

- - - - - - 4

- - - - - 6

Install the rudder 0servo

Connecting rod head

- - - - - 2

3X25mm screw

- - - - - 3

2X10mm screw

- - - - - 2

3mm Lock Nut

- - - - - 3

Rod 1400mm steel wire

Aluminium tube

- - - - - - 2

HORN

4X40 Screw

Rod adjuster

- - - - 2

- - - - - 2

LL

RR

14

Connecting rod head

2.5X125mm rod

3X25mm screw

Install the tail pry

9mm plywood

A B

- - - - - 2

- - - - - 6

HORN

- - - - - 2

4X40 Screw

- - - - - 2

Rod adjuster

- - - - - 4

2X10mm screw

- - - - - 4

12

Install the rudder servo

Rod

- - - - 2

Aluminium tube

- - - - - - 2

Rod adjuster

- - - - - 2

2X10mm screw

- - - - - 2

15

9mm plywood

A B

3mm steel wire

Install the main landing gear

5.2mm Collar

- - - - - - 4

3X3mm screw

- - - - - - 4

Aluminum plate

- - - - - 6

3X20mm Tp screw

- - - - - -12

55

Accessory list for this page.

!

18

Install the wing support

16

Pressure plate

- - - - - 3

3X20mm Tp screw

Aluminum plate

4X35mm screw

4X55mm screw

4X16mm screw

4mm Lock nut

- - - - - -12

- - - - - -2

- - - - - 14

- - - - - 2

- - - - - 6

Install the main landing gear

Pressure plate

3X20mm Tp screw

Aluminum plate

- - - - - 3

- - - - - -12

- - - - - -2

D

19

,

D D

,

D

4X35mm screw

- - - - - 14

4X55mm screw

- - - - - 2

4X16mm screw

- - - - - 6

4mm Lock nut

- - - - - 6

Main wing&Horizontal/Vertical tail

A B

17

C C

Install the wing support

C C

,

E

,

20

Install the engine (80-100cc gas engine)

165mm165mm

fuel tankfuel tank

E

Securely glue together ,if coming off during flights. You lose control of your airplane which leads to accidents!

Throttle servoThrottle servo

L L

RR

66

Accessory list for this page.

!

23

Radio Equipment

3X25mm Screw

- - - - 2

3X16mm Screw

- - - - 5

3mm rubber band

- - - - 7

3mm washer

- - - - 7

21 21

Install the throttle servo

Linkage Stopper

- - - - 1

2mm Nut

- - - - 1

1.8X450mm Rod

- - - - - - 1

3X3mm Screw

- - - - - - 1

BatteryBattery

Install the canopy

ReceiverReceiver

Linkage Stopper

- - - - 1

2mm Nut

- - - - 1

22

After confirming the position(see front of fuel tank). Insert and tighten the screw.

Assembly of the full tank

Fuel pipe

1.8X450mm Rod

- - - - - - 1

3X3mm Screw

- - - - - - 1

Air pressure line

Fuel supply line

25

3X25mm Screw

- - - - 2

3mm rubber band

- - - - 2

Install the cowling

3mm washer

- - - - 2

PropellerPropeller

SpinnerSpinner

3X16mm Screw

- - - - 5

3mm rubber band

- - - - 5

3mm washer

- - - - 5

77

26

Adjustment.

27

Adjustment

Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level.

AILERON

Side view

Top view

28

Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level.

ELEV A TOR

Side view

Adjustment.

45 45

Adjust the travel of each control surface to the values in the diagrams. These values fit general flight capabilities. Readjust according to your needs and flight level.

Rudder

Side view

Top view

29

Never fly before checking the Cg s required position.

In order to obtain the CG specified ,reposition the receiver and battery.

Adjustment.

170mm170mm

45

Top view

CG

!

¾¯¸æ

Warning!

NEVER fly the model without well balancing.

88