Page 1
-1-
661-3 REMOTE CAR ALARM
USER INSTRUCTIONS
Proudly designed and engineered in Australia by CYCLOPS.
Congratulations on having one of the worlds most advanced and
unique Australian designed and engineered vehicle security systems,
installed in your vehicle!
IMPORTANT NOTICE:
Ensure your installer has programmed your individual PIN code
before taking your vehicle. (see “programming new PIN” section).
BUTTON #1 (LOCk/ARM)
Arming
Press the LOCK button to arm the system, the siren will chirp twice,
the indicators will ash twice, the LED ash slowly, the doors will
lock1.
Open dOOr WArning
The siren and indicators will pulse three times if a door is detected
open while arming.
Triggering The AlArm
The alarm can be triggered three seconds after the last door is closed.
The shock sensor will become active ten seconds after the alarm is
armed.
duress lOcking
The car doors can be locked by remote control1 without arming the
alarm system if the ignition switch is left in the ON position.
cAr lOcATing
While the alarm system is armed, press and hold the LOCK/ARM
button for 2 seconds to cause the siren and indicators to pulse ve
times.
BUTTON #2 (UNLOCk/DISARM)
disArming
Press the UNLOCK/DISARM button to disarm the alarm system, the
siren and indicators will ash once, the LED will ash rapidly and
the doors will unlock1.
AuTO-Arming
The system will auto arm 30 seconds after the system has been
disarmed. While the ignition is on the 30 second countdown is reset.
This feature is programmable.
AuTO-lOcking
If none of the doors are detected as having been opened after
disarming, the doors will automatically lock1 after 30 seconds.
diAgnOsTics
If the alarm has been triggered during an arm cycle, the siren and
indicators will ash four times when next disarmed.
Requires central locking connection - optional extra.
siren reseT
While the siren is sounding, press the UNLOCK/DISARM button
momentarily to cancel the siren sound and disarm the system fully.
unlOcking The dOOrs
Pressing the UNLOCK/DISARM button while the ignition switch is
on or off will unlock1 the doors.
BUTTON #3 (PANIC /BOOT RELEASE)
pAnic
While ignition switch is Off, hold the PANIC/BOOT RELEASE
button for more than three 3 seconds to command the alarm to panic.
The siren and indicators will pulse for 30 seconds.
BOOT releAse
While the system is disarmed, momentarily press the PANIC/BOOT
RELEASE button to activate the boot release output of the alarm
system. The indicators will ash four times to conrm the action.
SILENT ARMINg
Press the LOCK/ARM and UNLOCK/DISARM button together for
two seconds to cancel the arm/disarm conrmation chirp for one
operation. The siren will still provide an OPEN DOOR WARNING
and DIAGNOSTICS in this mode.
RE-ARM & RELOCk
a. Relock: The alarm will rearm & relock1 the doors in 30 seconds if
no doors have been opened. This is to prevent accidental disarm.
b. Passive arm: the alarm will automatically arm after 30 seconds if
the ignition is turned off, then the doors are closed. This feature can
be disabled.
c. Passive lock: The alarm will automatically lock the doors 30
seconds after the ignition is turned off and the last door is closed.
This feature can be enabled. Warning: Strongly recommended not to
be used as key can be accidentally locked inside the car.
d. Anti Hi-jack: When enabled, the alarm will lock the doors four
seconds after the ignition switch is turned on. The alarm will unlock1
the door immediately after the ignition is switched off. This feature
will not activate while the door is open.
SPECIAL CONSIDERATIONS
If your vehicle is tted with a fading dome light, you should only
arm the 66-3 alarm after it is extinguished as a fading dome light
will “trick” the alarm into thinking that one of the doors is open
during the arm cycle. An open door warning is signalled by 3 chirps
PROgRAMMINg NEW REMOTE
. Disarm the alarm by pressing the UNLOCK/DISARM button.
2. Open the driver’s door and leave the door open.
3. Switch ignition switch Off and On 7 times.
4. When the 7th count is reached, leave ignition switch in the ON
position.
5. Vehicle indicators will begin ashing when alarm is ready to
accept new remote codes.
6. Press the LOCK/ARM on new remote control.
7. Test remotes by arming and disarming the alarm system.
CYCL PS
VEHICLE SOLUTIONS
Page 2
-2-
OPTION SETTINgS
Passive Arm / Transmitter Code-Learning / Passive Lock / Ignition
Lock &Unlock / Set Override PIN.
. Disarm the alarm by pressing the UNLOCK/DISARM button.
2. Open the driver’s door and leave door open.
3. Turn ignition switch On the number of times corresponding to
the feature you wish to alter. Refer to the Option Table for option
selection number.
4. When the correct count is reached, leave ignition switch ON.
5. Vehicle indicators will ash when alarm is ready to change option.
6. Press the LOCK/ARM button on a valid remote control.
7. Alarm will ash vehicle indicators to conrm change, see option
table for one/three ash meaning.
OPTION SETTINgS
Passive Arm / Transmitter Code-Learning / Passive Lock / Ignition
Lock &Unlock / Set Override PIN.
. Disarm the alarm by pressing the UNLOCK/DISARM button.
2. Open the driver’s door and leave door open.
3. Turn ignition switch On the number of times corresponding to
the feature you wish to alter. Refer to the Option Table for option
selection number.
4. When the correct count is reached, leave ignition switch ON.
5. Vehicle indicators will ash when alarm is ready to change option.
6. Press the LOCK/ARM button on a valid remote control.
7. Alarm will ash vehicle indicators to conrm change, see option
table for one/three ash meaning.
*** Warning this function can result in keys being locked in
vehicle!!
Ignition
Switches
Feature One Flash Three
Flashes
3 Anti-Hijack Disabled Enabled
5 Passive arming Disabled Enabled
7 Program new remote Press new remote control
13
Chirps for ARM /
DISARM
Disable Enable
15
Passive Locking Disabled Enabled
19
Set new PIN Begin changing PIN
EMERgENCY PIN OVERRIDE
In the event a remote is lost, stolen or broken, the 661-3 alarm
system may be overridden by using the programmed two digit
Personal Identication Number (PIN).
1. Insert ignition key into vehicle ignition switch.
2. Turn key to the ON position (the position just before engine
crank). The red status LED will glow constantly.
3. Return the key to the ACC position (the rst position that powers
your radio).
4. The status LED will begin ashing slowly. Count the ashes.
5. When the ashes match the rst number in your PIN, turn the
ignition switch to the ON position again.
6. Repeat step #5 for the second digit of the PIN.
7. The status LED will extinguish and the 66-3 will now be
disarmed and engine will start.
PROgRAMMINg NEW PIN
. Disarm the alarm by pressing the UNLOCK/DISARM button.
2. Open the driver’s door and leave door open.
3. Switch ignition switch Off and On 19 times.
4. When the 19th count is reached, leave ignition switch ON.
5. Vehicle indicators will ash when alarm is ready accept new
remote PIN.
6. Press the LOCK/ARM button the number of times corresponding
to the rst digit of the new PIN. Press UNLOCK/DISARM the
number of times corresponding to the second digit of the new PIN.
This step is critical, the timing between pressing the LOCK/ARM
button and pressing UNLOCK/DISARM must be as short as
possible. Any unprovoked indicator ash before the UNLOCK/
DISARM button is pressed means the PIN programming procedure
has dropped out - start again!!!
7. Alarm will ash vehicle indicators three times to conrm
successful programming.
*** All central locking and boot release features require additional
hardware, which is not supplied with the 661-3 alarm system.
Vehicles with central locking and/or electronic boot release will still
require connections to the 661-3 which are not a part of a standard
installation.
Control Module
Siren and Remotes
CYCL PS
VEHICLE SOLUTIONS
Loading...