Cycle Torch White LED Headlight & Red Tail Bolt COMBO User Manual

1

User Manual EN

White LED Headlight &

Red Tail Bolt COMBO

2

Thank you for purchasing one of our products !!!

We are truly honored to be able to serve you and provide you with the best

Experience possible. If you’ve enjoyed our product, we would sincerely appreciate

your honest feedback.

To insure maximum experience and safety, familiarize yourself with ALL

aspects of your new lights and battery system:

I. Safety precaution .......................................................................................... 3

II. How to mount White Headlight & Tail Bolt .................................................. 3

III. How to charge White Headlight & Tail Bolt ................................................. 4

IV. Switching the lighting modes ........................................................................ 5

V. Model Specifications...................................................................................... 5

VI. Warranty, Support and Customer Service .................................................... 6

I.

II.

III.

IV.

V.

If for any reason you are not satisfied, please contact us as soon as
possible at: [e-mail] , so that we can work with you to
solve whatever issues!

3

I. Safety Precaution

1. Never look directly into White Headlight or Tail Bolt;

2. Do not place the set within children’s reach;

3. Before your trip, please make sure that the White Headlight & Tail Bolt is firmly
mounted, it lights up, and the light is not blocked by baggage;

5. This product is waterproof under normal daily use and can be used in the
rain. However, do not intentionally submerge it in water.

Failure to follow these cations may expose you to risks, can cause
damage to the light system and will void the warranty !

A lighting system can make riding safer and you more visible, but lights are no
substitute for common sense. Ride within your capability with consideration for
the riding environment.

This product contains components that must be recycled per EU Directive
2002/96/EC and may not be disposed as unsorted municipal waste!

ll. How to mount White Headlight & Tail Bolt:

1. Attach the rubber strip to one end of the White Headlight / Tail Bolt bracket;

2. Hold the White Headlight / Tail Bolt with one hand and with another hand secure
it with the rubber strip across the handlebar or seat post;

3. For further details, click the link and watch the VIDEO.

I.

II.

III.

IV.

V.

4

III. How to charge White Headlight & Tail Bolt

How to charge:

1. Remove the rubber cap at the bottom of White Headlight / Tail Bolt;

2. Connect the White Headlight / Tail Bolt to your PC or a 5V USB battery charger

with the USB cable. The lens lights up RED when the charging starts;

3. When the lens lights up GREEN - charging is complete. Remove the USB cable;

4. Full charging time: 2 ~ 4 hours

Tips and tricks:

1. When your PC is in sleep state, the White Headlight / Tail Bolt cannot be charged;

2. Flashing light of the power button shows that a charging error has occurred.

Remove and reinsert the USB cable, then begin the recharge process again;

3. The battery charges to about 80% after approximately 2 hours;

4. Charging and lighting times are approximate values, and will vary by

environmental and user conditions.

I.

II.

III.

IV.

V.

WARNING: The cable (or other accessories) supplied with the Cycle Torch bike

light MUST be used only to charge the Cycle Torch bike light. The Manufacture
or/and the Seller are not responsible for any damage caused by using the supplied
accessories with other devices, other than Cycle Torch bike lights.

5

IV. Switching the lighting modes

Operation Modes: The initial two short presses (or single press for earlier models) of the

power button will turn on the light on High mode. Each additional short press of the
button switches the light from one mode to the next, in the following order: (1) High;

(2) Slow flashing; (3) Quick flashing; (4) Pulse; (5) OFF. Press & Hold of the power

button will shut down the Tail Bolt.

Low Battery Level: The White Headlight / Tail Bolt will automatically turn
off when the battery level is too low. This system protects the battery from
damage, but since it draws a small amount of current, and can drain the battery
beyond the minimum voltage for the battery, so it’s not recommended to turn
ON the lights after the programmed shutdown.

Do not wait until the White Headlight & Tail Bolt goes completely out as
this will greatly reduce the number of charge cycles that the battery can be
used and can render the battery unusable. It is highly recommended to
recharge periodically the White Headlight & Tail Bolt.

Charge your bike lights each 2-3 months when stored or not in use to
prevent battery degradation.

V. Model Specifications

 Model range: White Headlight & Tail Bolt
 Water-resistant front & rear tail light brightness: 20 LM & 10 LM
 Waterproof Grade: IP65
 Light Source: 3535 LED ultra Bright

Operating modes:

High

Slow

flashing

Quick

flashing

Pulse

Headlight run time (in hours)

2,5

8-10

5-8

5-8

Headlight power (in lumens )

20

20

20

20

Taillight run time (in hours)

5

15-20

10-15

10-15

Taillight power (in lumens)

10

10

10

10

I.

II.

III.

IV.

V.

6

 LED lifespan: 50,000 hours
 Low power consumption
 Battery: lithium-polymer rechargeable
 Charge time: 2 ~ 4 hours
 Material: high quality aluminum and top-class nylon plastic (ABS), weighing only 30g
 Finish: black
 Included accessories:

- Silicone straps;

- Micro USB charging cable.

VII. Warranty, Support and Customer Service

To register you product please go to http://cycletorch.com and follow the steps.
Our product quality is controlled strictly in accordance within the standards

of CYCLE TORCH quality certification program.

To ensure that all users enjoy the product, we offer one year warranty
within one year from purchase date, under normal use, the consumer will be
provided free warranty service for any quality related problems!

When requesting warranty service, customer should present Order ID .

Warranty Service Exclusions:

A) Any damages that are caused by other than normal use, including, but not
limited to physical damages.

B) Any user modification, repairs or disassembly of the product without
factory authorization.

C) Missing warranty Registration.

I.

II.

III.

IV.

V.

For further information concerning warranty conditions or for any
additional issues, please e-mail us at: [e-mail]