Cycle Torch Tail Bolt User Manual

User Manual EN

Tail Bolt

1

III.

If for any reason you are not satisfied, please contact us as soon as
possible at: [e-mail] , so that we can work with you to
solve whatever issues!

Thank you for purchasing one of our products !!!

We are truly honored to be able to serve you and provide you with the best

Experience possible. If you’ve enjoyed our product, we would sincerely appreciate

your honest feedback.

To insure maximum experience and safety, familiarize yourself with ALL

aspects of your new light and battery system:

I. Safety precaution .......................................................................................... 3

II. How to mount Tail Bolt to a bicycle ............................................................. 3

III. How to charge Tail Bolt.................................................................................. 4

IV. Switching the lighting modes ........................................................................ 5

V. Model Specifications...................................................................................... 5

VI. Warranty, Support and Customer Service .................................................... 6

2

I. Safety Precaution

III.

1. Never look directly into Tail Bolt;

2. Do not place it within children’s reach;

3. Before your trip, please make sure that the Tail Bolt is firmly mounted to the
seatpost, it lights up, and the light is not blocked by baggage;

5. This product is waterproof under normal daily use and can be used in the
rain. However, do not intentionally submerge it in water.

Failure to follow these cations may expose you to risks, can cause

damage to the light system and will void the warranty !

A lighting system can make riding safer and you more visible, but lights are no
substitute for common sense. Ride within your capability with consideration for
the riding environment.

This product contains components that must be recycled per EU Directive
2002/96/EC and may not be disposed as unsorted municipal waste!

ll. How to mount Tail Bolt to a bicycle:

1. Attach the rubber strip to one end of the Tail Bolt bracket;

2. Hold the Tail Bolt with one hand and with another hand secure it with the rubber
strip across the seatpost;

3. For further details, click the link and watch the VIDEO.

3

III. How to charge Tail Bolt

III.

WARNING: The cable (or other accessories) supplied with the Cycle Torch bike

light MUST be used only to charge the Cycle Torch bike light. The Manufacture
or/and the Seller are not responsible for any damage caused by using the supplied
accessories with other devices, other than Cycle Torch bike lights.

How to charge:

1. Remove the rubber cap at the bottom of Tail Bolt;

2. Connect the Tail Bolt to your PC or a 5V USB battery charger with the USB cable.

The lens lights up RED when the charging starts;

3. When the lens lights up GREEN - charging is complete. Remove the USB cable;

4. Full charging time: 2 ~ 4 hours

Tips and tricks:

1. When your PC is in sleep state, the Tail Bolt cannot be charged;

2. Flashing light of the power button shows that a charging error has occurred.

Remove and reinsert the USB cable, then begin the recharge process again;

3. The battery charges to about 80% after approximately 2 hours;

4. Charging and lighting times are approximate values, and will vary by

environmental and user conditions.

4

IV. Switching the lighting modes

Operating modes:

High

Slow

flashing

Quick

flashing

Pulse

Run time (in hours)

2

15-20

10-15

10-15

Power (in lumens)

10

10

10

10

III.

Operation Modes: Short press of the operation button will switch through

cycles & shut down the Tail Bolt. The initial short press of the power button will turn
on the light on High mode. Each additional short press of the button switches the
light from one mode to the next, in the following order: (1) High; (2) Slow flashing;
(3) Quick flashing; (4) Pulse; (5) OFF.

Low Battery Level: The Tail Bolt will automatically turn off when the
battery level is too low. This system protects the battery from damage, but since
it draws a small amount of current, and can drain the battery beyond the
minimum voltage for the battery, so it’s not recommended to turn ON the lights
after the programmed shutdown.

Do not wait until the Tail Bolt goes completely out as this will greatly
reduce the number of charge cycles that the battery can be used and can
render the battery unusable. It is highly recommended to recharge periodically
the Tail Bolt.

Charge your bike light each 2-3 months when stored or not in use to
prevent battery degradation.

V. Model Specifications

 Model range: Tail Bolt
 Water-resistant rear tail light brightness: 10 LM
 Waterproof Grade: IP65
 Light Source: 3535 LED ultra lumineux
 LED lifespan: 50,000 hours
 Low power consumption

5

 Battery: lithium-polymère rechargeable

III.

For further information concerning warranty conditions or for any
additional issues, please e-mail us at: [e-mail]

 Charge time: 2 ~ 4 hours
 Battery discharge time:

- 120 minutes in High mode

- 900 ~ 1200 minutes in Slow flashing mode

- 600 ~ 900 minutes in Quick flashing

- 600 ~ 900 minutes in Pulse mode

 Material: high quality aluminum and top-class nylon plastic (ABS), weighing only 30g
 Finish: black
 Included accessories:

- Silicone strap which fits all standard seat posts;

- Micro USB charging cable.

VII. Warranty, Support and Customer Service

To register you product please go to http://cycletorch.com and follow the steps.
Our product quality is controlled strictly in accordance within the standards

of CYCLE TORCH quality certification program.

To ensure that all users enjoy the product, we offer one year warranty
within one year from purchase date, under normal use, the consumer will be
provided free warranty service for any quality related problems!

When requesting warranty service, customer should present Amazon Order

ID or numbers provided by online retailers.

Warranty Service Exclusions:

A) Any damages that are caused by other than normal use, including, but not
limited to physical damages.

B) Any user modification, repairs or disassembly of the product without
factory authorization.

C) Missing warranty Registration.

6