Cybex international Plate Loaded Incline Press Owner’s and Service Manual

Cybex® Plate Loaded Incline Press

Owner’s and Service Manual

Strength Systems

Part Number 16190-999-4 A

www.cybexinternational.com

Cybex® Plate Loaded Incline Press

Owner’s and Service Manual

Strength Systems

Part Number 16190-999-4 A

Cybex® and the Cybex logo are registered trademarks of Cybex International, Inc.

DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.

© Copyright 2010, Cybex International, Inc. All rights reserved.
Printed in the United States of America.

10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX [phone]
www.cybexinternational.com • [e-mail] • 16190-999-4 A • June 2010

Table of Contents

1 Safety

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Guidelines and Practices . . . . . . . 2

Warning/Caution Decals . . . . . . . . . . . . . 3

Regular Maintenance Activities . . . . . . . . 4

2 Exercise

Intended Use . . . . . . . . . . . . . . . . . . . . . . 4

Instructions. . . . . . . . . . . . . . . . . . . . . . . . 4

3 Customer Service

Contacting Service. . . . . . . . . . . . . . . . . . 5

Ordering parts . . . . . . . . . . . . . . . . . . . . .5

Return Material Authorization (RMA). . . . 6

Damaged Parts . . . . . . . . . . . . . . . . . . . .6

4 Assembly

Tools Required. . . . . . . . . . . . . . . . . . . . . 7

5 Maintenance

Daily Procedures . . . . . . . . . . . . . . . . . . . 8

Weekly Procedures . . . . . . . . . . . . . . . . . 8

6 Service

Parts Lists . . . . . . . . . . . . . . . . . . . . . . . 12

Exploded-View Diagram . . . . . . . . . . . . 13

Page i

Cybex Plate Loaded 16190 Incline Press Owner’s Manual

1 - Safety

Safety

Read the Owner’s Manual carefully before assembling, servicing or using Cybex equipment.

WARNING: Serious injury could occur if these safety precautions are not observed:

User Safety Precautions

Obtain a medical exam before beginning any exercise program.•
Stop exercising if feeling faint, dizzy or experiencing pain and consult your physician.•
Obtain instructions before using. Lisez les instructions avant I’untilisation.•
Read and understand the owner’s manual and all warnings posted on the machine before using• .

Keep all children (12 and under) away. Teenagers (13 and over) and disabled must be supervised. •
Garder tous les enfants (de 12 ans et moins) éloignés. Les adolescents (de 13 ans et plus) et les
handicapés doivent être surveillés.

Use a spotter.•

Keep body and clothing free from and clear of all moving parts.•

Use the machine only for the intended use. • DO NOT modify the machine.

Inspect machine prior to use. • DO NOT use if it appears damaged or inoperable.

DO NOT • attempt to fi x a broken or jammed machine.

Report any malfunctions, damage or repairs to the facility• .

Replace any warning labels if damaged, worn or illegible.•

Facility Safety Precautions

Read the Owner’s Manual carefully before assembling, servicing or using this equipment. •

Securely anchor machine to the fl oor using the anchor holes provided in each machine. •

NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional

contractor.

NOTE: Use fasteners having a minimum of 500 lbs. tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any leg or frame

not in contact with surface using fl at washers.

Make sure that each machine is set up and operated on a solid level surface. • Do not install

equipment on an uneven surface.

Make sure that all users are properly trained on how to use this equipment.•

Make sure there is enough room for safe access and operation of this equipment. •

Perform regular maintenance checks on this equipment. Also pay close attention to •

all areas most susceptible to wear.

Page 1

Cybex Plate Loaded 16190 Incline Owner’s Manual

Immediately replace worn or damaged components. If unable to immediately replace worn or •

damaged components then remove from service until the repair is made.

NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular

maintenance is performed.

Safety Guidelines And Practices

Cybex recommends that all fi tness equipment be used in a supervised area. It is recommended that the equipment be
located in an access controlled area. Control is the responsibility of the owner. The extent of control is at the discretion
of the owner.

It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s manual, and warning
labels; as well as instruct all individuals, whether end users or supervising personnel, on proper usage of the equipment.

PROPER USAGE:

Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine is at rest or in use.

Inappropriate or improper use may result in injury to users or third parties (bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure that the facility has

the proper clearance for usage and training.

SECURING EQUIPMENT:

The machine has holes in the feet, which allow for ease in anchoring to the fl oor. Cybex strongly recommends that,
to eliminate rocking, tipping or falling over due to incorrect usage and misuse, equipment be secured to a solid, level
surface.

1. The solid, level surface should not deviate more than 1/8” over a 10’ distance or as defi ned and required by local
building and architectural codes.

2. Anchoring of equipment must be completed by a qualifi ed licensed contractor.

3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the

equipment to the fl oor.

4. Due to the wide variation of fl ooring on which machines may be anchored or installed, verify anchoring method and
anchoring fasteners with a qualifi ed and licensed contractor.

5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position..

6. Do not use machine until it is properly anchored.
MAINTENANCE:

Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform the maintenance
requirements as specifi ed in the manual.

STANDARD COMPLIANCE:

Cybex products meet or exceed applicable ASTM and EN Standards.

Page 2