CYBEX XP4040, XP4010, XP4080, XP4400 Installer/user Manual
XP4000 Series
Installer/User Guide
4991 Corporate Drive
Huntsville, Alabama 35805-6201 • USA
256-430-4000 (Fax) 256-430-4030
www.cybex.com
INSTRUCTIONS: The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
PROTECTIVE GROUNDING TERMINAL: A terminal which must be
connected to earth ground prior to making any other connections to the
equipment.
POWER ON: This symbol indicates the principle on/off switch is in the on
position.
POWER OFF: This symbol indicates the principle on/off switch is in the off
position.
Table of Contents
Chapter 1: Product Overviews
XP4000 Series Overview .......................................................... 1
XP4010/XP4040/XP4080 Units................................................. 1
Operation Modules .................................................................... 4
Cables ....................................................................................... 5
XP4000 Series Complements ................................................... 5
Features and Benefits ............................................................... 5
Limitations & Restrictions .......................................................... 7
Safety Precautions .................................................................... 8
Chapter 2:
Installing User Interface Modules
Connecting the Local Console Peripherals
(Front Access Model Only) ...................................................... 9
Secondary Console Modules .................................................... 10
Installing the Secondary Console Modules (XPDU and XPLU) 10
Connecting the User Interface Cables (XPDU and XPLU) ....... 11
Using Non-multisync Monitors .................................................. 15
Chapter 3:
Attaching Computers to an XP4000 Series Unit
Attaching a PC Computer ......................................................... 17
Attaching an IBM RS/6000 Workstation .................................... 24
Attaching a Silicon Graphics Workstation ................................. 25
Attaching a Macintosh Computer .............................................. 26
Attaching a Sun Workstation ..................................................... 30
Attaching a Hewlett-Packard Workstation ................................. 34
Chapter 4: Attaching Terminals
Overview ................................................................................... 39
Installing the XPIQ and XPSI Modules...................................... 40
Attaching Terminals to the XPSI Module ................................... 40
Addressing Terminals on the XPSI Module ............................... 41
Getting Started .......................................................................... 41
On-Screen Menu Overview ....................................................... 43
Using System Management Tools ............................................. 46
Using the Security Monitor ........................................................ 49
Chapter 5: Installing Expansion Units
Overview ................................................................................... 51
Expansion Capabilities .............................................................. 51
Installation ................................................................................. 52
XP4000 Unit Placement ............................................................ 52
Computer/User Console Distribution......................................... 54
Transmitter/Receiver Board Configuration ................................ 56
Transmitter/Receiver Board and Expansion Cable Installation . 59
Chapter 6: XP4400
XP4400 Overview ..................................................................... 61
Features and Benefits ............................................................... 63
Installation ................................................................................. 63
LED Operation .......................................................................... 66
LCD Display Operation ............................................................. 67
FLASH Upgrading ..................................................................... 70
Sample Configurations .............................................................. 71
Chapter 7: Basic Operations
LEDs and Front Access Display ................................................ 75
Multiplatform Keyboard Translation ........................................... 77
Keyboard Control ...................................................................... 79
Keyboard Switching .................................................................. 80
Multiuser Operation ................................................................... 81
Multimedia Operation ................................................................ 85
Serial Peripherals ...................................................................... 85
KeyScan .................................................................................... 86
Broadcast Mode ........................................................................ 87
Follow Mode .............................................................................. 88
Swap Mode ............................................................................... 88
Privacy Mode ............................................................................ 88
Command Forwarding............................................................... 89
Chapter 8:
XPDU Module and On-Screen Display
Overview ................................................................................... 91
On-Screen Menu Overview ....................................................... 92
The Channel List Menu (User Level Access) ............................ 92
The User List Menu ................................................................... 93
User Controls Menu (User Level Access) ................................. 94
The Command Line Entry Menu ............................................... 95
Administrator Functions ............................................................ 96
Administrator Controls............................................................... 99
Dual Monitor Support ................................................................ 102
Chapter 9: Advanced Operations
System Control and Maintenance ............................................. 105
Serial Port Advanced Operations
(for XPLU, XPDU and LCI modules) .................................... 106
Serial Port Advanced Operations (for XPRB Modules) ............. 108
Multi-Part FLASH Upgrades...................................................... 111
Keyboard Switching with Different Cybex Products .................. 112
Physical and Virtual Switches of Computer Interface Modules ......... 113
Chapter 10: Applications
Star/Daisy Chain Combination Configuration............................ 115
Recommended Configurations.................................................. 116
Chapter 11
Complement Products and Optional Modules
XPRB Module............................................................................ 123
The ReBoot xP .......................................................................... 126
Chapter 12:
Product Assistance and Troubleshooting
Customer/Technical Support ..................................................... 127
Troubleshooting......................................................................... 127
Chapter 13: Appendices
Appendix A ................................................................................ 131
Appendix B ................................................................................ 137
Appendix C................................................................................ 138
Appendix D................................................................................ 139
Appendix E ................................................................................ 140
Appendix F ................................................................................ 141
Appendix G ............................................................................... 144
Appendix H................................................................................ 145
Appendix I ................................................................................. 146
1
Product Overviews
XP4000 Series
Overview
XP4010/XP4040/
XP4080 Units
The XP4000 Series products allow multiple users to operate PC-compatible,
Macintosh, Sun, RS/6000, Silicon Graphics and Hewlett-Packard computers at
the same time. A basic XP4000 system consists of users and computers that are
all connected to one or more XP units. Any user in the system can access any
attached computer by simply 'switching' to that channel through the XP unit.
There are four chassis types available in the XP4000 Series: The XP4010, the
XP4040, the XP4080 and the XP4400. All models can be used in any
combination within one XP4000 system.
An XP system consists of four main components:
●
One or more XP4040/XP4010/XP4080/XP4400 units
●
A combination of operation modules
●
Associated cables to connect users and computers to the system.
●
Optional XP4000 Series complement products
The quantity and type of components you receive depends on the specific
configuration you order.
The XP4040 Unit
Front Access Desktop Model:XP4040D
The front panel of a front access XP4040 unit has 9 connectors as follows:
General overview of
Front and Rear Access
models
These connectors are used to attach a keyboard, monitor, mouse, microphone,
speakers and serial device to the front panel of the XP4040. Peripherals
attached to the front of the box make up your local console.
Each front access XP4040 unit supports up to 14 modules. The first slot on the
far left side of the XP4040D (viewed from the rear) contains the local console
●
PS/2 Keyboard
●
PS/2 Mouse
●
Serial Mouse
●
Macintosh
●
Sun
●
VGA Video
1
●
Serial Port
●
Microphone
●
Speakers
interface (LCI) module. The LCI comes pre-installed in the unit. The remaining 13 slots in the unit may be configured as user consoles, attached computers, power control or expansion modules.
There are 12 push-buttons on the front panel labeled A through L. These
buttons select the active computer for the local console. The indicator lights
(LEDs) over each push-button reflect the type of activity, if any, that is taking
place on each attached computer. The alphanumeric display in the upper right
hand corner of the front panel shows which computer channel is currently
selected by the local console. Only the local console utilizes the push-buttons
and alphanumeric display. Secondary consoles, which connect to the XP4040
through the rear of the unit, select their active computer via the keyboard.
Secondary consoles, like the local console, have access to every computer in
the XP4040 system.
LCI MODULE (FRONT ACCESS MODEL ONLY)
LCI MODULE (FRONT ACCESS MODEL ONLY)
AC INPUT
90-240 VAC, 47-63 Hz
1 AMP FAST BLOW
250 VAC
Front Access Rack Mount Model:XP4040R
Cybex also offers a front access model designed for 19 inch rack use. It
supports all the features of the XP4040D Front Access unit.
Rear Access Desktop Model:XP4040ED
The front panel of a rear access model XP4040E features LEDs only. These
LEDs reflect the power and selection status of all of the modules in that unit.
There are no connectors or alphanumeric display on the front of the unit.
There is no LCI (local console interface) module inside the unit. All 14 slots
are available for the installation and configuration of any module in the
system. All users connect through the rear of the unit and change computer
channels via keyboard switching.
AVAILABLE SLOTS FOR OPERATION MODULES
AVAILABLE SLOTS FOR OPERATION MODULES
AC INPUT
90-240 VAC, 47-63 Hz
1 AMP FAST BLOW
250 VAC
2
Rear Access Rack Mount Model:XP4040ER
Cybex also offers a rear access model designed for 19 inch rack use. It supports
all the features of the XP4040E rear access unit.
Rear Access Rack Mount Model:XP4080ER
The XP4080ER rear access rack mount model supports all of the features of the
XP4040ED and XP4040ER models. Additionally, with this model, users can
access up to eight computers simultaneously and independently instead of the
four supported by XP4040 models. Used primarily in larger configurations
utilizing the XP4400 chassis, this model reduces the overall number of
XP4040 units required in the system
Power
On-Line
Selected
abcdefghijklmn
The XP4010 Unit
Differences between the
XP4010 and XP4040
systems
The XP4010 unit looks and functions like a front access XP4040D model with
the following exceptions:
1. An XP4010 system supports a maximum of five modules: the local user
console, pre-installed in the XP4010, and four additional modules which
can be configured as additional user consoles, attached computers, or
expansion modules.
2. The XP4010 front panel does not support an alphanumeric display.
3. The XP4010 is available in a front access desktop model only. Kits are
available for rack mounting. (RMK 19,20,21)
3
The XP4400 Unit
The XP4400 chassis is designed to accommodate larger XP system installations.
By channeling expansion signals from XP4040 users to attached computers,
the XP4400 enables large configurations with fewer XP4040 units, transmitter/
receiver cards and cables in the system. The XP4400 consists of a 9U high
chassis, containing two power supplies, two fan assemblies and a user specified
number of XP4400 transmitter and receiver modules. There are no users or
computers attached directly to this unit. There is an LCD display on the front
panel for the internal menuing system and four buttons that control menu
selections and operations.
Each module contains 16 sets of video and keyboard/mouse ports, enabling a
module to attach to as many as 16 XP4040 expansion ports, using two category
5 cables each. The XP4400 holds up to nine transmitter or receiver modules
per chassis. For more information on the XP4400, see Chapter 6.
Operation
Modules
Depending on the chassis used, an XP4000 Series unit can support from 4 to
up to 14 individual operation modules, including the local console module, if
applicable. Modules may be ordered in any combination required, and are
easily installed by sliding them gently through the rear of the unit. See the
diagram below.
Basic modules are used to attach users and computers to the XP4000 system.
Advanced modules are used for linking multiple XP4000 Series units together,
power control and terminal emulation.
4
Cables
Each operation module, except the LCI, requires a cable to connect it to an
attached computer, user console, or other XP4000 Series unit. Computer
interface cables connect computers to the XP4000 Series unit. User interface
cables connect users to the unit. Expansion cables may be as long as 250 feet
and connect expansion units together. Typical cables are shown below.
C
XP4000 Series
Complements
Features and
Benefits
AutoBoot capability
Built-in scanning
capabilities
User interface cables
(CPIUF-10 shown)
CLX expansion cable
(used in expansion
systems only)
XP4000 Series complements are optional products that work in conjunction
with the XP4010/XP4040 and XP4080 to give your system added flexibility
and control. For a detailed description of available complement products, see
Chapter 11.
The XP4000 Series AutoBoot feature boots all of your attached computers
during initial power-up or after a power failure. All computers are booted
transparently and simultaneously, eliminating the need for operator
intervention. Computers may be powered up one at a time or all at once.
KeyScan, a built-in scanning feature, allows you to automatically monitor or
scan all of your computer channels sequentially without intervention. When
KeyScan detects keyboard or mouse activity, scanning is suspended until all
activity stops. Scanning then resumes with the next computer in sequence. The
length of time each computer channel remains on the screen, or dwell time, is
configurable and can be changed at any time.
Multiplatform
The XP4000 Series adds multiplatform capabilities to your switching system
by simultaneously supporting any combination of PC, Macintosh, Sun, RS/
6000, Silicon Graphics or Hewlett-Packard computers in the same system.
Along with the ability to access many different types of computers and
workstations, you can now use any platform's peripherals to do it! You can use
any type of keyboard and mouse to access any type of computer in the system.
For example, a PC keyboard and mouse can operate a Sun server as easily as
a Sun keyboard and mouse will operate an attached PC.
Multiuser
Another useful feature is the multiuser capability of the XP4000 Series.
Instead of just one user having access to many different attached computers,
these products allow multiple users simultaneous access to different computers
in the system. This is called “matrix switching”. So, a system with four users
accessing four different computers would be a 4 x 4 matrix.
5
If two or more users need access to the same computer, they can ‘share’ access
to it through the XP units. Sharing means that multiple users can switch to the
same computer at the same time. Everyone can see that computer's video, but
only one can enter data at any given moment.
Expansion capability
Multimedia
Local User Console
The primary user console has access
to every computer in the system, as
well as control over the push-button
front panel of the XP4000 Series Unit.
If your total number of computers and users is greater than 14, use our
expansion modules. Connecting an expansion transmitter in one XP Series unit
to an expansion receiver in another XP Series unit lets you combine multiple
units in one system. Control thousands of computers from one set of peripherals!
Transmitters and receivers are available with Cybex proprietary or industry
standard category 5 UTP cable connections. Category 5 cables can be ordered
in standard or extended distance versions. With Cybex or UTP standard
distance cabling, each XP Series unit can be up to 250 feet apart; a user and the
farthest accessible computers can be up to 500 feet apart.
Users in an XP Series system also have the option of multimedia support.
Every user has access to a dedicated keyboard, mouse and video monitor as
well as optional microphone and stereo speaker connections.
Secondary User Console
Secondary user consoles have access
to every computer in the system.
Mac keyboard, mouse, &
multisync* monitor
Channel C:
Sun Workstation/server
PC keyboard, mouse,
& multisync* monitor
On-screen management
Multi-level security
Serial port
Channel D:
IBM Compatible PC
Secondary User Console
Secondary user consoles have access
to every computer in the system.
Sun keyboard, mouse, &
multisync* monitor
FIGURE 1-1
Channel E:
Macintosh Computer
*Monitor must be capable of synchronizing with any attached computer’s video output.
For on-screen management and multi-level security, try the XPDU deluxe user
module. Name your servers, then select them from a pop-up menu. Quick edit
capability lets you change channel name or address on the fly. Control features
allow you to manage scanning and broadcast operations on-screen as well.
On-screen management also supports multi-level security with password
protection. Control how much access users have to each computer in your data
center. An additional feature is the optional logout after a user defined period
of inactivity. When the timeout is reached, the current channel is deselected
and the screen goes blank. Users must login again to access system computers.
A serial port is also available, allowing for the use of a printer or similar serial
device at the console. This serial port can optionally be used as a serial access
port to the XP Series Control Menu. From this menu, you can determine your
6
revision level, system configuration and even upgrade the firmware to keep
your system current at all times.
FLASH upgrading
Field-replacable
plug-in modules
Keep Alive capability
Individual power
control
Limitations &
Restrictions
FLASH technology allows the XP Series firmware to be updated without ever
removing a module or even powering down the system. New firmware revisions
can be uploaded into the XP4000 Series through the serial port. The latest
firmware revisions are available to all users through Technical Support or via
the internet.
Since the XP Series units are component based products, all modules are fieldreplaceable plug-in boards. They can be added or replaced without
disassembling or even powering down the switch or attached computers. This
capability makes installation, configuration and maintenance much simpler.
The "Keep Alive" capability of the XP Series allows attached computers to power
the computer modules in the event of a power failure. Keeping the modules
powered up in an emergency prevents the computers from locking up needlessly.
The optional ReBoot xP allows you to control the power to computers in your
XP Series system individually. No matter where a system computer is located,
you can cycle the power, or “reboot”, an attached computer from your XP
Series unit.
The following models of mice have been tested and are known to be compatible
with the XP Series:
Mouse support
Use capable multisync
monitors only
Use Cybex supplied
cables only
Speaker support
Microphone support
Microsoft Serial-PS/2 mouse Kensington PS/2, ADB
Microsoft OEM style serial mouse Mouse Systems
Microsoft Intellimouse Logitech Mouseman/Trackman
Sun Microsystems Laser mouse IBM PS/2-style
Apple ADB mouse
Other manufacturers' mice generally operate with the XP Series. If you
experience problems using an untested mouse, contact Cybex Technical Support
with the manufacturer and model number of the mouse.
Monitors at all consoles must be capable of synchronizing with any attached
computer’s video rate. If you are unsure whether your monitors are of the
multisync type, consult the monitor documentation or contact your dealer.
Use only Cybex supplied cable with the XP Series. Poorly constructed or
miswired cabling will diminish video quality and possibly damage equipment.
Cybex warranties do not apply to damage resulting from user supplied cables.
The XP4000 Series supports all externally powered speakers using 3.5 mm
miniplugs. Use powered speakers with the XP Series for best performance.
The XP4000 Series supports “mono” microphones with 3.5 mm miniplugs.
Powered microphones are not recommended; if a computer channel is selected
that supplies power to the microphones, the microphone volume may be muted
on that channel.
Serial support
The XP4000 Series supports RS-232 serial devices using hardware or inband
flow control: hardware up to 9600 Baud, inband to 115200 Baud.
7
Safety
Precautions
To avoid potential video or keyboard problems when using Cybex
products:
Check environment
Ensure proper
grounding
• If the building has 3-phase AC power, ensure that the computer and
monitor are on the same phase. For best results, they should be on the
same circuit.
• Use only Cybex-supplied cable. Cybex warranties do not apply to damage resulting from user-supplied cable.
To avoid potentially fatal shock hazard and possible damage to
equipment, please observe the following precautions:
• Do not use a 2-wire extension cord in any Cybex product configuration.
• Test AC outlets at computer and monitor for proper polarity and grounding.
• Use only with grounded outlets at both the computer and monitor. When
using a backup power supply (UPS), power the computer, the monitor
and the XP4000 Series unit off the supply.
• With the exception of adding or removing original Cybex manufactured
modules in accordance with written Cybex instructions, the XP4000 Series
unit and all attached computers should be powered down before servicing
the unit. Always disconnect the power cord from the unit.
Note: The AC inlet is the main disconnect.
Rack Mount Safety Considerations
• Elevated Ambient Temperature: If installed in a closed rack assembly,
the operation temperature of the rack environment may be greater than
room ambient. Use care not to exceed the rated maximum ambient temperature of the unit.
• Mechanical Loading: Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical loading.
• Circuit Overloading: Consideration should be given to the connection of
the equipment to the supply circuit and the effect that overloading of
circuits might have on overcurrent protection and supply wiring. Consider equipment nameplate ratings for maximum current.
• Reliable Earthing: Reliable earthing of rack mounted equipment should
be maintained. Pay particular attention to supply connections other than
direct connections to the branch circuit (e.g. use of power strips).
Nameplate Rating: This product is rated 100-240 V ac, 50/60 Hz. All components except the XP4400 are rated 1.6A (single component power supply) or 3.2A (dual component power supply). XP4400 is rated at 7 amps.
8
2
Installing User Interface
Modules
Connecting
the Local
Console
Peripherals
(Front Access
Model Only)
The keyboard, monitor, mouse, serial device, speakers and microphone at the
local console connect directly into either the corresponding ports on the front
panel of your XP4000 Series unit or the user interface cable for your XPLU
or XPDU card. No additional cables are required.
Any platform's keyboard and mouse can be plugged into the local console in
any combination. However, do not connect more than one keyboard, monitor
or mouse into the front of the unit. For example, you may use a Macintosh
mouse and a Sun keyboard at the workstation at the same time but you cannot
connect two keyboards or two mice into the front of the unit simultaneously.
SPEAKER
MIC
S
PS/2
KEYBOARD
PS/2
SERIAL MOUSE
MOUSE
L
K
J
I
H
G
F
E
D
C
B
A
SERIAL PORT
MAC
VGA
SUN
R
9
Secondary
Console
Modules
A secondary console module is one of the two types of user modules. While
the primary console peripherals connect through the front panel of the unit
(discussed in the previous section), secondary console modules have the
peripherals connected through the rear of the module. Currently we offer
versions with on-screen display capabilities (XPDU) and without (XPLU).
Installing the
Secondary
Console
Modules (XPDU
and XPLU)
The XPDU and XPLU modules are installed identically. There are no DIP
switches or jumpers to configure on either module
1. Position the XP4000 Series unit so that the rear panel is facing you.
Choose an available slot. An available slot will have a solid panel covering the opening to the unit, with no connectors showing through it.
NOTE: For front access models, the LCI module, located to the far left
of the unit (viewed from rear), is covered by a solid panel but IS NOT
an available slot. Only the LCI module can be installed in this slot.
LCI MODULE (FRONT ACCESS MODEL ONLY)
LCI MODULE (FRONT ACCESS MODEL ONLY)
AVAILABLE SLOTS FOR OPERATION MODULES
AVAILABLE SLOTS FOR OPERATION MODULES
AC INPUT
90-240 VAC, 47-63 Hz
1 AMP FAST BLOW
250 VAC
2. Remove the panel covering the available slot by unscrewing the two
Phillips-head screws on the rear of the unit that hold the panel in place.
3. Slide the new user interface (XPDU/XPLU) module gently into the open
slot of the XP4000 Series unit until the 62-pin connector lines up flush
with the back of the unit. See the diagram below.
4. Retighten the holding screws completely. DO NOT overtighten.
5. Fill out the XPDU/XPLU Configuration Chart in Appendix A for each
module as you install it.
Follow the above procedure for every XPDU/XPLU module in your system.
10
Connecting the
User Interface
Cables (XPDU
and XPLU)
User interface cables connect your secondary consoles to the XP4000 Series
unit. You will have a set for each secondary console in the system. These
cables are a user specified length with a 62-pin D-shaped male connector on
one end. The other end will have from two to six connectors, depending on the
options you ordered (See the table below). Use the instructions on the
following pages which apply to the type of peripherals you are attaching, and
repeat the process for each secondary console in the system. User interface
cables for the XPDU and XPLU user modules are identical
Peripherals User interface cables
Standard Multimedia
IBM AT-compatible keyboard CPMU-x CPMUF-x
with Serial mouse
PS/2-compatible keyboard CPIU-x CPIUF-x
with PS/2 mouse
Macintosh CPAU-x CPAUF-x
Sun CWSU-x CWSUF-x
Replace x with the distance cable you ordered.
For IBM AT-style keyboard, monitor and Serial mouse
1. Your user interface cables for these peripherals will be labeled either
CPMU-x or CPMUF-x , depending on the options you ordered. Use the
cable diagrams below to locate the correct cable.
VGA VIDEO
VGA VIDEO
SERIAL MOUSE
CPMU-x CABLE CPMUF-x CABLE
KEYBOARD
SERIAL MOUSE
(yellow band)
MICROPHONE
(blue band)
KEYBOARD
SERIAL PORT
SPEAKERS
2. At your secondary console, plug your keyboard, serial mouse and monitor
connectors into the three matching connectors on the user interface cable.
If you have the CPMUF-x series cable, you will have three additional
connectors: two small connectors for a microphone and speakers, and a 9pin D-shaped serial connector for a serial port. The microphone connector
is denoted by a blue band around its cable; the serial mouse connector is
denoted by a yellow band. Plug your peripheral connectors into the
matching connectors on the user interface cable.
3. Attach the user interface cable to the unit by plugging the 62-pin connector into the rear of any available secondary console module. Ensure that
the connector is firmly seated, then tighten the thumbscrews.
11
For PS/2-style keyboard, monitor and PS/2 mouse
1. Your user interface cables for these peripherals will be labeled either
CPIU-x or CPIUF-x , depending on the options you ordered. Use the cable
diagrams below to locate the correct cable.
KEYBOARD
SERIAL PORTPS/2 MOUSE
SPEAKERSMICROPHONE
VGA VIDEO
VGA VIDEO
KEYBOARD
(yellow band)
PS/2 MOUSE
(yellow band)
(blue band)
CPIU-x CABLE CPIUF-x CABLE
2. At your secondary console, plug your PS/2-style keyboard, PS/2 mouse
and monitor connectors into the matching connectors on the user interface
cable. The mouse connector is denoted by a yellow band around its cable.
If you have the CPIUF-x series cable, you will have three additional
connectors: two small connectors for a microphone and speakers, and a 9pin D shaped serial connector for a serial port. The microphone connector
is denoted by a blue band around its cable. Plug your peripheral connectors into the matching connectors on the user interface cable.
3. Attach the user interface cable to the unit by plugging the 62-pin connector into the rear of any available secondary console module. Ensure that
the connector is firmly seated, then tighten the thumbscrews.
NOTE: You may use your SGI, RS/6000 or HP workstation monitor with an
XP4000 Series unit if it will function with all of your attached computers/
workstations. See “Using Non-multisync Monitors” later in this chapter.
12
For Macintosh keyboard and mouse
1. Your user interface cables for these peripherals will be labeled either
CPAU-x or CPAUF-x , depending on the options you ordered. Use the
cable diagrams below to locate the correct cable.
ADB
SPEAKERS
SERIAL PORT
VGA VIDEO
VGA VIDEO
ADB
MICROPHONE
(blue band)
SERIAL MOUSE
SERIAL MOUSE
(yellow band)
CPAU-x CABLE CPAUF-x CABLE
2. At your secondary console, plug your Mac keyboard/mouse and VGA
monitor connectors into the two matching connectors on the user interface cable.
NOTE: For users requiring multi-button mice, a serial mouse connector is
also provided.
If you have the CPAUF-x series cable, you will have three additional
connectors: two small connectors for a microphone and speakers, and a 9pin D-shaped serial connector for a serial port. The microphone connector
is denoted by a blue band around its cable; the serial mouse connector is
denoted by a yellow band. Plug your peripheral connectors into the
matching connectors on the user interface cable.
3. Attach the user interface cable to the unit by plugging the 62-pin connector into the rear of any available secondary console module. Ensure that
the connector is firmly seated, then tighten the thumbscrews.
NOTE: You may use your Macintosh monitor with an XP4000 Series unit if it
will function with all of your attached computers. See “Using Non-multisync
Monitors” later in this chapter.
13
For Sun keyboard and mouse
1. Your user interface cables for these peripherals will be labeled either
CWSU-x or CWSUF-x , depending on the options you ordered. Use the
cable diagrams below to locate the correct cable.
VGA VIDEO
KEYBOARD/
MOUSE
VGA VIDEO
MICROPHONE
(blue band)
SERIAL PORT
KEYBOARD/MOUSE
SPEAKERS
CWSU-x CABLE CWSUF-x CABLE
2. At your secondary console, plug your Sun keyboard/mouse and VGA
monitor connectors into the two matching connectors on the user interface cable.
If you have the CWSUF-x series cable, you will have three additional
connectors: two small connectors for a microphone and speakers, and a 9pin D-shaped serial connector for a serial port. The microphone connector
is denoted by a blue band around its cable. Plug your peripheral connectors into the matching connectors on the user interface cable.
3. Attach the user interface cable to the unit by plugging the 62-pin connector into the rear of any available secondary console module. Ensure that
the connector is firmly seated, then tighten the thumbscrews.
NOTE: You may use your Sun monitor with an XP4000 Series unit if it will
function with all of your attached computers/workstations. See ‘Using Nonmultisync Monitors’ later in this chapter.
14
Using
Non-multisync
Monitors
Using your SGI, RS/6000 or HP Workstation Monitor
1. You may use your SGI, RS/6000 or HP workstation monitor with an
XP4000 Series unit if it will function with all of your attached computers/
workstations. In order to connect your monitor, you will need a video
adaptor from Cybex. These devices adapt the VGA video output to your
workstation monitor's input. If you do not have one of the adaptors listed
below, contact our Sales Department.
Monitor Connector Type Adaptor Type
BNC VAD-19
13W3 (SGI) VAD-14
3C3 VAD-20
13W3 (RS 6000) VAD-22
Using your Macintosh Monitor with an XP4000 Series unit
1. You may use your Macintosh monitor with an XP4000 Series unit if it will
function with all of your attached computers. In order to connect this type
of monitor, you will need a VAD-16 video adaptor from Cybex. This
device adapts the VGA video output to your Mac monitor's input. If you
do not have this adaptor, contact our Sales Department.
2. Follow the instructions above for the installation of a Macintosh keyboard
and mouse, making sure to attach the VAD-16 adaptor between your user
interface cable and your Mac monitor cable.
Using your Sun Monitor with an XP4000 Series unit
1. You may use your Sun monitor with an XP4000 Series unit if it will
function with all of your attached computers/workstations. In order to
connect this type of monitor, you will need a VAD-13 video adaptor from
Cybex. This device adapts the VGA video output to your Sun monitor's
input. If you do not have this adaptor, contact our Sales Department.
2. Follow the instructions above for the installation of a Sun keyboard and
mouse, making sure to attach the VAD-13 adaptor between your user
interface cable and your Sun monitor cable.
Changing XPDU settings for Non-PC Monitors
In some cases you may not see video the first time you power up a Sun or Mac
Monitor attached to an XPDU. If this happens:
1. Hold down the <CTRL><ALT><Shift> and <M> keys at one time.
2. The monitor will begin to cycle through settings. When you see video on
your screen, press the <ENTER> key.
Your monitor should begin to work normally.
15
16
5
6
4
2
3
1
2
3
1
*
Attaching Computers to
3
Attaching a PC
Computer
XPAC module shown
an XP4000 Series Unit
Before you connect your PC to the XP4000 Series unit, you will need to configure
and install your computer interface module. The XPAC, XPAB and XPAL
computer interface modules have one set of DIP switches to configure. The XPAC
and XPAB also have jumpers to configure. Follow the steps below to configure
each XPAC, XPAB or XPAL module that will be connected to a PC computer.
Configuring your computer interface (XPAC/XPAB) modules
Configuring the Jumpers
The jumpers on the XPAC/XPAB module are used to control the video
selection settings. The default is IBM VGA/SVGA video. If the computer you
are attaching supports this video mode, no adjustment is required and you may
proceed to the DIP switch settings.
DIP-SWITCH
ASSEMBLY
44-PIN
CONNECTOR
J1
J3
J5J6J4
J2
IBM VGA/SVGA
(DEFAULT)
J4
J3
J6
J5
J2
J1
1
2
3
Orient your XPAC/XPAB module so that the 44-pin connector is to your right
as shown above. Locate the jumpers on the lower right hand corner of the
board. The XPAC will contain JP1 - JP6; the XPAB module will only have
jumpers JP1 - JP5. Configure your XPAB module as you would an XPAC,
ignoring all references to JP6.
Use the diagrams below to configure the video settings for the PC computer
that you will attach to this computer interface module. You may wish to
consult your computer or video card reference manual for the video rates
supported by your computer.
* XPAC Modules only
3
1
2
1
2
3
4
5
6
*
IBM VGA/SVGA
VIDEO
JUMPERS
17
3
1
2
1
2
3
4
5
6
*
IBM XGA IIIBM XGA
Configuring the DIP Switch (XPAC, XPAB and XPAL)
The DIP switch is used to configure three different features: video options and
sync, keyboard/mouse time-out and keyboard translation options (Mac only).
The diagram below shows the DIP switch, the positions used to configure each
of these features, and the default settings.
Keyboard/Mouse
Translation
Reserved
Video Options
Your XP4000 Series unit is factory set for PC video. No changes are needed
to switches 1 through 3 for normal PC video.
By default, a computer's video will be displayed for any console user that
switches to that channel. If you do not want a computer's video to be displayed,
you can disable the video for that channel. Additionally, if you are only
running your keyboard and mouse through the XP4000 Series unit, and your
video is independent of the system, you should select the option to disable the
video. See the table below.
Timeout
Video
7 8
Switch 1 Switch 2 Switch 3
Off Off Off Normal video (default)
On On On Video disabled
Function
Video Sync - XPAB only
Your XPAB card will attempt to automatically detect the sync for your
monitor. In some unique instances it will obtain the opposite of the settings.
Switching S7 to the on position will correct this. See the table below.
Switch 7
Off Autodetect (default)
On Reverse Autodetected Sync
Sync Mode
Keyboard/Mouse Time-out
While multiple consoles can view a computer's video at the same time, only
one station can have keyboard and mouse control at a time. The amount of time
that a console's keyboard and mouse must be inactive before another console
can take control is called the time-out. See the table below for the available
time-outs that can be configured.
Switch 4
Off 1 second (default)
On 10 seconds
Time
Note: Once your XPAC/XPAB module has been installed, you can change the
DIP switch setting at any time through a simple hot-key sequence. See Chapter
9, Advanced Operations for more information.
18
Installing the computer interface modules (XPAB and XPAC)
1. Position the XP4000 Series unit so that the rear panel is facing you.
Choose an available slot. An available slot will have a solid panel covering the opening, with no connectors showing through it.
NOTE: For front access models, the LCI module, at the far left of the
unit (viewed from rear), is covered by a solid panel but IS NOT an
available slot. Only the LCI module is installed in this slot.
LCI MODULE (FRONT ACCESS MODEL ONLY)
LCI MODULE (FRONT ACCESS MODEL ONLY)
AVAILABLE SLOTS FOR OPERATION MODULES
AVAILABLE SLOTS FOR OPERATION MODULES
AC INPUT
90-240 VAC, 47-63 Hz
1 AMP FAST BLOW
250 VAC
2. Remove the panel covering the available slot by unscrewing the two
Phillips-head screws on the rear of the unit that hold the panel in place.
3. Slide the new computer interface module gently into the open slot of
the unit until the 44-pin connector lines up flush with the back of the
unit. See the diagram below.
4. Retighten the holding screws completely. DO NOT overtighten.
5. Fill out the Configuration Chart in Appendix A for each module as you
install it.
Follow this procedure for every computer interface module in your system.
19
Installing the computer interface modules (XPAL) with a PC
Follow steps 1-5 of the XPAB and XPAC installation instructions on the
previous page and then proceed with the following steps:
6. Place the LongView Transmitter near the remote computer that you wish
to connect to your XPAL. Connect the Cybex custom cable (marked
CUFC) to the 25-pin INPUT connector on the rear of the Transmitter.
7. Unplug the peripherals (keyboard, mouse, monitor, speakers, microphone and serial device if applicable) from your computer.
8. Connect the CUFC cable’s 15-pin video connector to the video output
connector on your PC.
9. Plug the 6-pin connector into the PS/2 Keyboard jack on your PC.
10. If you use the serial mouse connector on the Transmitter’s CUFC cable,
do not connect anything to the Transmitter’s
PS/2 mouse connector you may extend the serial Com port from the PC
to the user for other devices.
port. If you use the
11. Using standard 3.5mm stereo patch cords, connect the
connector on
the rear of the Transmitter to the speaker or line output jack of your
computer and the
connector to the microphone input jack of your PC.
12. Plug the circular power plug from the provided wall-mount power
supply into the
jack on the rear of the Transmitter, then plug the
power supply into a convenient electrical outlet. Verify that the
POWER light on the front of the Transmitter is lit.
13. Plug a standard Category 5 Unshielded Twisted Pair cable (up to 500
feet) into the remote I/O jack on the rear of the Transmitter. Cybex
C5T, Cybex P5T, Belden 1583A or Belden 1585A cable is strongly
recommended to achieve best performance and maximum distance. If
you use a different Category 5 cable, make sure it is terminated to the
EIA (TIA) 568 B standard, commonly used for 10BaseT Ethernet. Do
NOT use a crossover cable. Incorrect termination can damage the
LongView Transmitter.
14. Route the Category 5 cable back to your XPAL and connect it to the
Category 5 jack.
15. Select the XPAL from your XP4000 Series unit. If you are using a
serial mouse enter <CM>SW15=1<Enter>, otherwise enter
<CM>SW15=0<Enter>.
16. Reselect the XPAL and type <CM>SW16=0<Enter>
Follow this procedure for every XPAL in your system.
20
Installing the computer interface modules (XPAL) with a Sun
Follow steps 1-5 of the XPAB and XPAC installation instructions on page 19
and then proceed with the following steps:
6. Place the LongView Transmitter near the remote computer that you wish
to connect to your XPAL. Connect the Cybex custom cable (marked
CUFC) to the 25-pin INPUT connector on the rear of the Transmitter.
7. Unplug the peripherals (keyboard, mouse, monitor, speakers, microphone and serial device if applicable) from your computer.
8. If needed, plug the 13W3 male video adapter into the video port on
back of the Sun workstation.
9. Install the 8-pin mini-DIN male adapter into the keyboard/mouse port
on the back of the Sun workstation.
10. Plug the CUFC cable into the appropriate connectors of the VAK-1
adapters.
11. Plug the 15HDD male adapter into the video port on the back of your
LongView receiver.
12. Plug the 6-pin mini-DIN male adapter into the keyboard and mouse
ports on your LongView receiver.
13. Plug the monitor and Sun keyboard/mouse cables into the VAK-1 adapters.
14. Power your XP4000 Series unit, LongView Receiver and Sun computer
on. Keyboard and mouse should work normally.
15. Once this is done, select the XPAL from your XP4000 Series unit. Type
the following command, <CM>SW15=0<Enter>.
16. Reselect the XPAL and type <CM>SW16=1<Enter>
Follow this procedure for every XPAL in your system.
21
Connecting the Computer Interface Cables
Computer interface cables connect your computers to the XP4000 Series unit.
You will have a set for each computer in your XP4000 system. These cables
are a user specified length with a 44-pin D-shaped female connector on one
end. The other end will have from 2 to 8 connectors, depending on the cable
you ordered and the kind of computer you are attaching. The table below
shows the cables that are compatible with your PC computer. Use the
instructions on the following pages that apply to the cable and computer type
you are attaching, and repeat the process for each additional PC computer in
your XP4000 Series system.
Computer Computer interface cables
Standard Multimedia
IBM AT-compatible CPUC-x CPUF-x
with Serial mouse
IBM PS/2-compatible CPUC-x CPUF-x
with PS/2 mouse
Replace x with the distance cable you ordered.
For IBM AT compatible computers with serial mouse capability
1. Your computer interface cables for this computer will be labeled either
CPUC-x or CPUF-x , depending on the options you ordered. Use the
cable diagrams below to locate the correct cable.
VGA VIDEO
KEYBOARDVGA VIDEO
SERIAL MOUSE
(yellow band)
SERIAL MOUSE
SERIAL PORT
KEYBOARD
MICROPHONE
(blue band)
SPEAKERS
CPUC-x CABLE CPUF-x CABLE
2. Power down your computer, then plug the cable's keyboard, serial
mouse and VGA monitor connectors into the matching ports on the PC.
If you have the CPUF-x series cable, you will have three additional
connectors: two 3.5mm connectors for a microphone and speakers, and
a 9-pin D-shaped serial connector for a serial port. The microphone
connector is denoted by a blue band around its cable; the serial mouse
connector is denoted by a yellow band. Plug these connectors into the
appropriate ports on your PC or peripheral device.
3. Attach the computer interface cable to the unit by plugging the 44-pin
connector into the rear of the appropriate computer interface module.
Ensure that the connector is firmly seated, then tighten the thumbscrews.
22
For IBM PS/2 style computers with PS/2 mouse capability
1. Your computer interface cables for this computer will be labeled either
CPIC-x or CPIF-x , depending on the options you ordered. Use the cable
diagrams below to locate the correct cable.
VGA VIDEO
VGA VIDEO KEYBOARD
PS/2 MOUSE
(yellow band)
PS/2 MOUSE
(yellow band)
SERIAL PORT
KEYBOARD
MICROPHONE
(blue band)
SPEAKERS
CPIF-x CABLECPIC-x CABLE
2. Power down your computer, then plug the cable's keyboard, PS/2
mouse and VGA monitor connectors into the matching ports on the PC.
The mouse connector is denoted by a yellow band around its cable.
If you have the CPIF-x series cable, you will have three additional
connectors: two 3.5mm connectors for a microphone and speakers, and
a 9-pin D-shaped serial connector for a serial port. The microphone
connector is denoted by a blue band around its cable. Plug these connectors into the appropriate ports on your PC or peripheral device.
3. Attach the computer interface cable to the XP4000 Series unit by
For XPAB modules using the optional ReBoot xP
To attach your ReBoot xP to your XPAB computer interface module, see the
section “The ReBoot xP” in Chapter 11.
plugging the 44-pin connector into the rear of the appropriate computer
interface module. Ensure that the connector is firmly seated, then
tighten the thumbscrews.
23
Attaching an
IBM RS/6000
Workstation
For RS/6000 Systems using standard VGA video
1. If your RS/6000 system utilizes standard VGA video, refer to the
previous section, “Attaching a PC Computer” and follow the instructions for configuring and installing your XPAC/XPAB modules, and
connecting computer interface cables for IBM PS/2 style computers.
For RS/6000 Systems using 13W3 video
1. If your RS/6000 system has a 13W3 video connector, refer to the
previous section, “Attaching a PC Computer” and follow the instructions for configuring and installing your XPAC/XPAB modules.
13W3 VIDEO CONNECTOR
2. In order to connect the computer interface cables, you will need a
VAD-21 adaptor from Cybex. If you do not have this adaptor, contact
our Sales Department to order one.
3. Follow the instructions for connecting computer interface cables for
IBM PS/2 style computers making sure to attach the VAD-15 between
the VGA video connector on your computer interface cables and your
RS/6000 workstation.
For RS/6000 Systems using 3C3 video
1. If your RS/6000 system has a 3C3 video connector, refer to the previous section, ‘Attaching a PC Computer’ and follow the instructions for
configuring and installing your XPAC/XPAB modules.
3C3 VIDEO CONNECTOR
2. Set the DIP switch on your XPAC/XPAB module as shown below:
Switch 1 Switch 2 Switch 3
Off Off Off Normal video. Use with monitors that
support sync on green.
Off Off On Use sync on green to generate horizontal
and vertical sync
3. In order to connect the computer interface cables, you will need a
VAD-18 adaptor from Cybex. If you do not have this adaptor, contact
our Sales Department to order one.
Function
24
Loading...