CyberResearch MXIH CEL-24-X, MXIH P4-26-X, MXIH P4-34-X User Manual

Motherboards

MXIH Series

MXIH CEL-24-X: ATX, 2.4GHz Celeron CPU, 4 PCI
Slots, 2 ISA Slots, AGP, LAN, VGA, DOC, USB

MXIH P4-26-X
PCI Slots, 2 ISA Slots, AGP, LAN, VGA, DOC, USB

MXIH P4-34-X: ATX, 3.4GHz Pentium 4 CPU, 4 PCI
Slots, 2 ISA Slots, AGP, LAN, VGA, DOC, USB

: ATX, 2.66GHz Pentium 4 CPU, 4

®

USER’S MANUAL

VER. 1.0 • DEC 2006

No part of this manual may be reproduced without permission

CyberResearch®,Inc.

www.cyberresearch.com

25 Business Park Dr., Branford, CT 06405 USA

203-483-8815 (9am to 5pm EST) FAX: [phone]

CyberResearch® Motherboards MXIH Series

©Copyright 2003

All Rights Reserved.

December 2003

The information in this document is subject to change without prior notice
in order to improve reliability, design, and function and does not represent
a commitment on the part of CyberResearch, Inc.

In no event will CyberResearch, Inc. be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use of or inability
to use the product or documentation, even if advised of the possibility of
such damages.

This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of CyberResearch, Inc.

Trademarks

“CyberResearch,” and “MXIF Series,” are trademarks of CyberResearch,
Inc. Other product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of
their respective companies.

• NOTICE •

CyberResearch, Inc. does not authorize any CyberResearch product for
use in life support systems, medical equipment, and/or medical devices
without the written approval of the President of CyberResearch, Inc. Life
support devices and systems are devices or systems which are intended
for surgical implantation into the body, or to support or sustain life and
whose failure to perform can be reasonably expected to result in injury.
Other medical equipment includes devices used for monitoring, data
acquisition, modification, or notification purposes in relation to life
support, life sustaining, or vital statistic recording. CyberResearch
products are not designed with the components required, are not subject
to the testing required, and are not submitted to the certification required
to ensure a level of reliability appropriate for the treatment and diagnosis of
humans.

CyberResearch, Inc. iii

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

Intentionally Blank

iv ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

Table of Contents

Introduction.............. ................. ................. .............. 1

Checklist..............................................................................1

Product Description.............................................................2

Specifications.......................................................................3

Board Dimensions .............................................................10

Installation.............................................................. 11

Installing the CPU .............................................................12

ATX Power Installation.....................................................13

Installing the Memory........................................................13

Setting the Jumpers............................................................14

Jumper Locations on MXIH SERIES................................15

JP1: RS232/422/485 (COM2) Selection............................16

JP2: COM1 RS232 +5V/+12V Power Setting...................16

JP3: COM2 RS232 +5V/+12V Power Setting...................16

JP4: Clear CMOS Contents................................................17

JP5: COM3 RS232 +5V/+12V Power Setting...................17

JP6: COM4 RS232 +5V/+12V Power Setting...................17

JP7: DiskOnChip Address Select.......................................18

JP8: Onboard VGA Enable/Disable...................................18

Connectors on MXIH SERIES..........................................19

Connector Locations on MXIH SERIES...........................20

ATXP1: ATX Power Supply Connector............................21

ATXP2: ATX 12V Power Connector................................21

DIMM1, DIMM2: DDR Channel A Connectors...............21

DIMM3, DIMM4: DDR Channel B Connectors...............21

AGP1: AGP Slot............................. ...................................21

PCI1, PCI2, PCI3, PCI4: PCI Slots ...................................21

SL1, SL2: ISA Slots...........................................................21

CN1: PS/2 Keyboard and PS/2 Mouse Connectors...........22

CN2: 4-port USB Connector..............................................22

CN3, J3: Serial Ports..........................................................22

CN4: Parallel Port Connector............................................22

CN6: VGA CRT Connector...............................................23

CN7: USB and LAN RJ45 Connectors..............................24

CN8: Audio Connector......................................................24

J1: IrDA Connector............................................................24

J4: CD-In Audio Connector...............................................24

J5, J6: Serial ATA (SATA) Connectors.............................25

J8, J10: COM3 and COM4 Serial Ports Connector...........25

CyberResearch, Inc. v

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

J9: Wake On LAN Connector............................................25

J11: Digital I/O Connector (4 in, 4 out)............................. 26

J12: System Function Connector.......................................26

J13: USB Connector ..........................................................28

FAN1: CPU Fan Power Connector....................................28

FAN2: VGA Fan Power Connector................................... 28

FAN3: Chassis Fan Power Connector ...............................28

FDD1: Floppy Drive Connector........................................ 29

IDE, IDE2: Primary and Secondary IDE Connectors........ 30

Watchdog Timer Configuration ........................................31

BIOS Setup.............................................................35

BIOS Introduction .............................................................36

BIOS Setup........................................................................ 36

Standard CMOS Setup....................................................... 38

Advanced BIOS Features...................................................41

Advanced Chipset Features ...............................................44

Integrated Peripherals........................................................46

Power Management Setup.................................................5 0

PNP/PCI Configurations....................................................5 3

PC Health Status................................................................54

Frequency/Voltage Control................................................55

Load Fail-Safe Defaults.....................................................56

Load Setup Defaults ..........................................................56

Set Supervisor/User Password........................................... 56

Save & Exit Setup..............................................................56

Exit Without Saving ..........................................................56

Driver Installation...................................................57

Intel 875P Chipset Software Intallation Utility.................58

Realtek AC97 Codec Audio Driver Installation................61

Intel PRO LAN Drivers Installation..................................62

VGA Drivers Installation ..................................................63

vi ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

Introduction

Checklist

Your MXIH SERIES motherboard package should include the items listed
below:

• The MXIH SERIES motherboard

• This User’s Manual

• 1 Backplate

• 2 IDE Cables

• 1 Floppy Cable

• 2 SATA Cables

• 1 Dual-Serial-Port Cable

• 1 CD containing the following:

o Chipset Drivers
o Flash Memory Utility

CyberResearch, Inc. 1

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

Product Description

®

The MXIH SERIES Pentium

4/Celeron motherboard incorporates the Intel
875P chipset that can utilize a single PGA478 processor of up to 3.2GHz or
higher and supports FSB frequency of 400/533/800Mhz (100Mhz, 133Mhz,
and 200Mhz HCLK respectively).

®

The 875P chipset is designed for use with the Pentium

4 processor with
512-KB L2 cache on 0.13 micron process. The integrated MCH component
provides the CPU interface, DDR interface, AGP interface, Hub Interface and
AGP 8X graphics interface.

Four DDR memory sockets support DDR 400/333/266 SDRAM DIMM
modules of up to 4GB in capacity. ECC is also supported.

®

The board also comes with integrated Intel

82547GI Gigabit LAN controller.
Two Serial ATA connectors offer 1.5 Gigabits/sec data throughput speed ­faster than the most advanced parallel ATA.

Expansion is provided by four PCI slots, two ISA slots and one AGP8X
interface. Other advanced features include six USB 2.0 ports, IrDA interface,
PCI to ISA bridge, digital I/O, four serial ports, watchdog timer and audio
function. Dimensions of the board are 12” by 9.5” in an ATX form factor.

2 ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

Specifications

Processor

Processor Type (CPU) Included
Number of Processors/CPU Sockets Single CPU

CPU Socket Type Socket 478 (478 pins)
Processor Speed 2.4GHz; 2.66GHz; 3.4GHz
Maximum CPU Speed 3.4GHz
Processor FSB 533MHz

FSB (CPU Front Side Bus Speed)
Chipset Manufacturer Intel

Chipset Intel 875P

Memory

System
Memory

Memory Maximum 4GB
Memory Sockets 4 x 184-pin DDR DIMMs

Intel Celeron/Pe ntiu m
(Socket 478)

533MHz
800MHz

Memory Features

CPU
Cache
Size (per

L2 Cache

CPU)
Flash

Memory

Type

Socket(s)

• Supports 2.5V

DDR400/333
(supports dual
channel)

• Dual-channel DDR

interleaving requires
two DDR RAM
modules of iden tical
memory size and
speed

• Supports ECC

function

256K

DiskOnChip up to 288MB
(32-pin DIP)

CyberResearch, Inc. 3

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

System Details

Full-length standard card (7.5

Card Form Fa ctor

BIOS

Real-Time Clock (RTC)

BIOS Manufacturer Award
BIOS Chip Type Flash ROM

to 13.4")
ATX motherbo ard

On-board real-time clock
(RTC)

• Free system

assembly and test
when a motherboard
is purchased with a
CyberResearch
chassis, hard dr iv e,
and operating
system

• OIX 2107 benchtop

keyboard included

Special Features

free upon request
when you purchase
a complete system
with a CPU card or
motherboard

• RTC/CMOS Built in

ICH5R

• Please note tha t th is

motherboard does
not support
Win98/XNT

4 ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

Expansion Slots

Slot Quantity of Typical Chassis 8 slots
Expansion Sl ots (max. num b er of cards) 7 slots
Max. Number of PCI Cards 4
Max. Number of ISA Cards 2

Number of PCI Slots 4 PCI slots

PCI Slots

ISA Expansion Slots 2 ISA slots
AGP Slot Type 1 AGP slot

Slot Special Featur es

Type of PCI Slot(s)

32-bit 5V standard (notch
farthest from backplate)

While most ISA boards are
likely to work in these
models, 100% compatibility
with all extant ISA board s
cannot be guaranteed. 100%
satisfaction guaran teed -- we
will work with you to find a
solution for yo ur application
(call for details)

On-Board Video

Video RAM 2MB
Video Channels 1 x analog VGA
Video Chipset SMI 712
Video

Output
Signals

Video Bus Type AGP 8x
Video Output Connectors

Analog

Analog VGA (standard for CRT
or flat-panel)

HD15 (standard VGA)
connector

On-Board I/O

I/O Controller Winbond W83627HF

Intel 82547GI

On-Board
LAN

Serial
Ports

Ethernet Controller Type

Channels

Ethernet

Connector(s)

Wake-on-LAN Yes
Serial (COM)

Ports: RS-232

Number of
RS-232 Serial
Ports

RS-232 Signals
Supported

10/100/1000Base-TX
(Gigabit)

1 x Gigabit
(10/100/1000Base-T)

1 x RJ-45
2 LEDs indicate LAN access
and link status

3

TXD (TD, TX) Transmitted
Data
RXD (RD, RX) Rece ived Da ta
RTS : Request to Send
CTS : Clear to Send

CyberResearch, Inc. 5

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

DCD (CD) Data Carrier Detect
DSR : Data Set Ready
DTR : Data Term in al Re a dy
RI : Ring Indicator
GND : Signal Ground

Communications

Asynchronous (async)

Protocol

Serial (COM)
Ports:
RS-422/485

Number of
RS-422/485
Serial Ports

Serial Port Mode

1

Jumper-selectable

Select
Number of

1
RS-232/422/485
Serial Ports

Serial Port Mode

Jumper-selectable
Select

TXD (TD, TX) Transmitted

Serial (COM)
Ports:
RS-232/422/485

RS-232 Sign als
Supported

Data

RXD (RD, RX) Rece iv e d Da ta

RTS : Request to Send

CTS : Clear to Send

DCD (CD) Data Carrier Detect

DSR : Data Set Ready

DTR : Data Term in al Re a dy

RI : Ring Indicator

GND : Signal Ground

One DB-9 RS-232 port on I/O

backplate, two RS-232

Serial Port Connectors

headers and one

RS-232/422/485 header on

board

USB Ports, Total Qty. 8
USB 2.0 Ports (480Mbps) 8

USB
Ports

USB Connectors

6 standard female USB

sockets (Type A /

rectangular)

Header on card for 2 USB

ports

Parallel Ports, Total Qty. 1

ECP (Extended Capability

Port, bidirectional)

Parallel
Ports

Parallel Port Modes Supported

EPP (Enhanced Paralle l Po r t,

bidirectional)

SPP (Standard Parallel Port)

Standard DB-25 female

(IEEE-1284 Type A)

1 FDD port - supports up to 2

floppy drives

Up to 4 hard drives / devices

Floppy
Drive
Ports

EIDE

Connector Type

Number of Drives Supported
Connector Type 34-pin male header
Number of Drives/Devices

6 ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

(hard
drive)
Ports

SATA
(hard
drive)
Ports

IrDA
(infrared)
Port

Digital
I/O

Supported
EIDE Interface Type
Connector(s) 2 x 40-pin male headers

Number of Drives/Devices
Supported

SATA Interface Type
Connector(s) 2 x 7-pin SATA (male)

IrDA Connector

Number of I/O Lines 8
Configuration

Features

Ultra ATA/100 (ATA/100,
ATA-6) 100MB/sec

Up to 2 SATA drives

SATA 1.5Gb/s (SATA/150,
Serial ATA)

Header for IrDA (infrared)
port

4 inputs
4 outputs

12-pin digital I/O header
connector s uppor ts TT L lev els

Other Connectors

Keyboard Connector(s)
USB Keyboard Supported Yes

Pointing Device Connector PS/2 (6-pin mini-DIN female)

External Power Input Connector

ATX Power Control Connector

Chassis Controls Header

Fan Connectors
Chassis Intrusion Header 2-pin chassis intrusion header

1xPS/2 (6-pin mini-DIN
female)

ATX standard m ale co nnector
(20-pin)
ATX12V auxiliary 12V
connector (4-pin, 1 2V/GND)

2-pin header for ATX power
control

Header for reset switch
Header for ATX power switch
Header for power indicator
LED
Header for hard drive activity
LED

Standard 3-pin male
connector

Audio

Audio Support (on-board) 5+1 surroun d sound output
Audio Codec Supp orted AC'97

CyberResearch, Inc. 7

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

System Monitoring

Soft Off

Wake On LAN (WOL)

Wake On Keyboard

Wake On Ring (on

modem/serial ring detect)

ACPI/APM Function

Temperature 3 channels

CPU Thermal Alarm

Fan(s) 3 channels
Watchdog Timer Yes

Watchdog Time-Out Intervals

Wake On RTC Alarm (at a set

date & time)

Intruder Detect Input

Suspend to RAM (STR,

Standby)

Wake On PCI (allo ws wake up

from a PCI card)

Audible alarm if CPU exceed s

a user-specified temperature

System will shut down if CPU

exceeds a user-specified

temperature

1 to 255 seconds in 1 -second

intervals

Power Consumption

• 2GHz/400 P4 with

512MB DDR RAM:
+5V @ 0.47A, +12V
@ 9.34A

Power Consumption, typ.

• 2.4GHz/533 P4 with

512MB DDR RAM:
+5V @ 0.65A, +12V
@ 5.94A

+5VDC 650mA
+12VDC 9.34A

8 ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

Cooling

Fan for Processor (CPU Fan) 1 included

Environmental Specifications

Operating Temperature 32°F....140°F ( 0°C....60°C)

Storage Temperature -4°F....176°F (-20°C....80°C)

Relative Humidity, noncondensing 10%....90%

Safety & Standards Compliance

Safety/Approvals Meets RoHS standards

ACPI (Advanced

Power Management

Configuration and Power
Interface)

Dimensions

Width 12.01" (305mm)
Depth (front-to-rear) 9.59" (243.7mm)
Height (w/o CPU or RAM) 1.67" (42.44mm)

CyberResearch, Inc. 9

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

Board Dimensions

10 ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

Installation

This section provides inform ation on how to use the jumpers and connectors on
the MXIH SERIES in order to set up a workable system. The topics covered are:

Installing the CPU .............................................................12

ATX Power Installation.....................................................13

Installing the Memory........................................................13

Setting the Jumpers............................................................14

CyberResearch, Inc. 11

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

Installing the CPU

The MXIH SERIES motherboard supports a Socket 478 processor socket for

®

Intel

Pentium® 4 & Celeron processors.

The Socket 478 processor socket comes with a lever to secure the processor.
Raise this lever to about a 90° angle to allow the insertion of the processor.
Place the processor into the socket by making sure the notch on the corner of the
CPU corresponds with the notch on the inside of the socket. Once the processor
has slide into the socket, return the lever to the lock position. Refer to the figures
below.

After you have installed the processor into the socket, check if the jumpers for
the CPU type and speed are correct.

NOTE:

Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that can cause
your system to hang or be unstable.

12 ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

ATX Power Installation

The system power is provided to the motherboard with the ATXP1 and ATXP2
ATX power connectors. ATXP2 is a 4-pin 12V power connector. ATXP1 is to
be connected to a standard ATX power connector.

Installing the Memory

The MXIH SERIES motherboard supports four DDR memory sockets for a
maximum total memory of 4GB in DDR memory type. You can install
unbuffered & ECC DDR DIMMs. It supports DDR266 when installed with
CPUs that have clock speeds of 400MHz. It supports DDR266/333 when
installed with CPUs that have clock speeds of 533MHz. It supports
DDR266/320/400 when installed with CPUs that have clock speeds of
800MHz. The board provides dual channel functionality for its DIMM slots.
DIMM1/2is for one channel and DIMM3/4 is for another channel. Enabling
dual channels can increase data access rates by putting two similar-size DDR
modules into two same-color DIMM slots.

Basically, the system memory interface has the following features:

Supports two 64-bit wide DDR data channels
Available bandwidth up to 3.2GB/s (DDR400) for single-channel mode
and 6.4GB/s (DDR400) in dual-channel mode.
Supports ECC DIMMs.
Supports 128Mb, 256Mb, 512Mb, 1Gb DDR technologies.
Supports only x8, x16, DDR devices with four banks
Registered DIMMs not supported
Supports opportunistic refresh
Up to 16 simultaneously open pages (four per row, four rows maximum)

CyberResearch, Inc. 13

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

Setting the Jumpers

Jumpers are used on MXIH SERIES to select various settings and features
according to your needs and applications. Contact your supplier if you have
doubts about the best configuration for your needs. The following lists the
connectors on MXIH SERIES and their respective functions.

Jumper Locations on MXIH SERIES...........................................15

JP1: RS232/422/485 (COM2) Selection.......................................16

JP2: COM1 RS232 +5V/+12V Power Setting..............................16

JP3: COM2 RS232 +5V/+12V Power Setting..............................16

JP4: Clear CMOS Contents..........................................................17

JP5: COM3 RS232 +5V/+12V Power Setting..............................17

JP6: COM4 RS232 +5V/+12V Power Setting..............................17

JP7: DiskOnChip Address Select .................................................18

JP8: Onboard VGA Enable/Disable .............................................18

14 ©Copyright 2003 CyberResearch, Inc.

CyberResearch

®

Motherboards MXIH Series

Jumper Locations on MXIH SERIES

Jumper Locations on MXIH SERIES..................................................15

JP1: RS232/422/485 (COM2) Selection..............................................16

JP2: COM1 RS232 +5V/+12V Power Setting.....................................16

JP3: COM2 RS232 +5V/+12V Power Setting.....................................16

JP4: Clear CMOS Contents..................................................................17

JP5: COM3 RS232 +5V/+12V Power Setting.....................................17

JP6: COM4 RS232 +5V/+12V Power Setting.....................................17

JP7: DiskOnChip Address Select.........................................................18

JP8: Onboard VGA Enable/Disable.....................................................18

CyberResearch, Inc. 15

25 Business Park Drive P: [phone]; F: [phone]
Branford, CT USA www.cyberresearch.com

MXIH Series CyberResearch® Motherboards

JP1: RS232/422/485 (COM2) Selection

COM1 is fixed for RS-232 use only.
J3, COM2 is selectable for RS232, RS-422 and RS-485.
The following table describes the jumper settings for COM2 selection.

COM2

Function

Jumper

Setting

(pin closed)

RS-232 RS-422 RS-485

Short:

1-2
9-11
10-12
15-17

16-18

Short:

3-4
7-9
8-10
13-15
14-16

Short:

5-6
7-9
8-10
13-15
14-16

JP2: COM1 RS232 +5V/+12V Power Setting

JP2 Setting Function

Pin 1-2

Short/Closed

Pin 3-4

Short/Closed

Pin 5-6

Short/Closed

JP3: COM2 RS232 +5V/+12V Power Setting

JP3 Setting Function

Pin 1-2

Short/Closed

Pin 3-4

Short/Closed

Pin 5-6

Short/Closed

+12V

Normal

+5V

+12V

Normal

+5V

16 ©Copyright 2003 CyberResearch, Inc.