CyberPower PDU20MVHVIEC24F, PDU20BHVIEC10R, PDU20MVHVIEC30F, PDU20MVHVIEC38F, PDU10BVHVIEC16F User Manual

User Manual

Power

Distribution

Unit

Table of Contents

Model List 1

PDU Naming Convention: 1

Package Contents 1

Safety Precautions 2

Installation 2

Horizontal Installation (1U models only) 2

Vertical Installation with Brackets 3

Vertical Installation with Brackets (0U models only) 3

Vertical Installation with Keyhole Mounts (0U Models) 4

Cord Retention Tray installation 4

Meter Configuration 4

Electrical Installation 5

Troubleshooting 5

Product Features 6

Basic Series ( 1U 20A ) 6

Basic Series ( 0U 10A ) 7

Basic Series ( 0U 20A ) 8

Meter Series ( 0U 20A ) 9

1

For more information on CyberPower products, visit www.CPSww.com

PDU Naming Convention:

1. Amperage: Amperage – 15A, 20A, 30A

2. Series: B: =Basic M: =Metered
SW: = Switched

3. Rack Space: NULL: =Horizontal V:= Vertical

4. Input Voltage: HV:= High Voltage – 200V to 240V

5. Plug Type: IEC:= (IEC 320 C14/C20)

6. Outlet Number Front: Number of Outlets followed by
F – Example 8F

7. Outlet Number Rear: Number of Outlets followed by
R – Example 8R

Basic Series:

PDU20BHVIEC8R
PDU20BHVIEC10R
PDU20BHVIEC12R
PDU20BHVIEC12Ra

Basic Series:(0U)

PDU10BVHVIEC16F
PDU10BVHVIEC20F

PDU20BVHVIEC16F
PDU20BVHVIEC20F
PDU20BVHVIEC24F
PDU20BVHVIEC32F
PDU20BVHVIEC38F

Metered Series:(0U)

PDU20MVHVIEC24F
PDU20MVHVIEC30F
PDU20MVHVIEC38F

Package Contents

Model List

PDU (1)

Ground Screw M5 X 6 (1 pcs)

Horizontal Installation
Used (1 set)

Bracket Mounting
Screws M4 X 8 (4pcs)

Cord Retention Tray
Mounting Screws
M3 X 6 (4/8/12/16 pcs ­varies by models)

Keyhole Mounting Pegs (2pcs)
with Screws M4 X 8 (2pcs)
(for 0U models only)

Cord Retainer Clips
(8/10/12/14/16/20/24/30/
32/38 pcs - varies by models)
for Cord Retention Tray

Vertical Installation
Used (1 set)

Vertical Mounting Brackets
(1 set)(for 0U models only)

Mounting Brackets

Cord Retention Tray
(1/2/3/4 pcs - varies by models)

2

For more information on CyberPower products, visit www.CPSww.com

Safety Precautions
Read the following before installing or operating the
Power Distribution Unit (PDU):

1. Use only the supplied hardware to attach the mounting brackets.

2. The PDU must only be plugged into a three-wire, grounded outlet
on a circuit protected by a fuse or circuit breaker. Connection to
any other type of power outlet may result in a shock hazard.

3. Do not use extension cords or adapters with this PDU.

4. Never install a PDU or associated wiring or equipment during a
lightning storm.

5. Check that the power cord, plug, and socket are in good condition.

6. The socket-outlet shall be installed near the equipment and shall
be easily accessible.

7. CAUTION! To prevent the risk of fire or electric shock, this PDU
should be installed in a temperature and humidity controlled
indoor area free of conductive contaminants. Do not install this
PDU where excessive moisture or heat is present.

User Manual

Documentation:

Before using, please check to ensure the package contains all
the items shown above. If there are any missing parts, please
contact CyberPower technical support at www.CPSww.com

Pow

er

D

istri

bution

Unit

User M

a

n

ual

Check

Installation

Horizontal Installation (1U models only)

Step 1 – Mounting bracket installation

Install the screws (M4 X 8) in holes diagonally from each other.

Step 2 – PDU Mounting

Install the PDU using fasteners compatible with the rack.

3

For more information on CyberPower products, visit www.CPSww.com

Vertical Installation with Brackets

Step 1 – Mounting bracket installation

Vertical Installation with Brackets (0U models only)

Step 1 – Mounting bracket installation

Install the screws (M4 X 8) in holes diagonally from each other.

Step 2 – PDU Mounting

Step 2 – PDU Mounting

Install the PDU using fasteners compatible with the rack.

Install the PDU using fasteners compatible with the rack.

Attach the Vertical Mounting Brackets to the PDU with the 4
supplied Bracket Mounting Screws (M4 X 8).

4

For more information on CyberPower products, visit www.CPSww.com

Vertical Installation with Keyhole Mounts (0U Models)

Step 1 – Keyhole Mount installation

Meter Configuration

Cord Retention Tray installation

(Optional for both horizontal and vertical installations)

Attach the Keyhole Mounting Pegs to the PDU with the 2
supplied Bracket Mounting Screws (M4 X 8).

Align the the Keyhole Mounts to the Keyhole Slots on the rack.
Insert and slide down to lock firmly into place.

Step 2 – PDU Mounting

Depending on installation method (vertical or horizontal), the
LED Meter may need to be rotated, before installation, for
proper orientation.

Attach the Cord Retention Tray to the PDU with the 4 supplied
Cord Retention Tray Mounting Screws (M3 X 6).

Use a screw driver to gently remove the LED Meter. Rotate
the LED Meter 90 degrees, and insert back into the PDU.

!

Note

5

For more information on CyberPower products, visit www.CPSww.com

Electrical Installation

Step 1 – Receptacle evaluation
Ensure that the plug type of your PDU unit (e.g. NEMA 5-15P,
NEMA 5-20P, NEMA L5-30P) matches the wall receptacle type
that you are using.

Troubleshooting

PDU must be plugged into a three-wire, grounded
wall receptacle only. The wall receptacle must also be
connected to an appropriate branch circuit/main with fuse
or circuit breaker protection. Connection to any other type
of wall receptacle may result in a shock hazard.

Step 2 – Plug the PDU into the wall receptacle

Step 3 – Attach equipment

Before attaching equipment, it is important to calculate the total
load that will be placing on the PDU. It is extremely important
not to exceed the PDU's maximum current load (as outlined in
the Specifications section). In order to determine the total load,
simply add up the amperage of your devices and ensure that it
does not exceed the unit’s capacity.

Problem Possible Cause Solution

PDU outlets do
not provide power
to connected
equipment

1. Open breaker

2. Loose power cord

Reset breaker, check if plug
is completely connected.
If the problem remains,
contact tech support.

Amperage displayed
on Amperage Meter
exceeds the unit’s
capability
(Metered type only)

1. Overload

2. Amperage meter is
damaged

The meter will flash when
overloaded. Reduce the
load on the PDU until the
overload is gone.
If the problem remains,
contact tech support.

Circuit breaker
has tripped

1. Sustained overload

2. Excessive ambient
or internal
temperatures.

3. Faulty breaker

Reset breaker.
If the problem remains,
contact tech support.

6

For more information on CyberPower products, visit www.CPSww.com

A

R

A B C D E FF

Product Features

Front View

Technical Specifications

Model Name

PDU20BHVIEC8R
PDU20BHVIEC10R
PDU20BHVIEC12R

PDU20BHVIEC12Ra

Input

Voltage 200~240V

Max Current 20 A

Regulatory Derated
Input Current

16 A

Circuit Breaker 16 A

Plug Type IEC 320 C20

Power Cord Length 10 ft /3.05m

Output

Voltage 200~240V

Max Current 20 A

Outlet Type(Quantity)

IEC 320 C13(8)
IEC 320 C13(10)
IEC 320 C13(12)

IEC 320 C19(2)/C13(10)

Indicators

LED Indicators N/A

Meter Readout N/A

Physical

Dimension (WxDxH) 17.5" x 1.5" x 1.75" / 44.45 x 3.81 x 4.45 cm

Environmental

Humidity

Operating 0 to 95% Non-condensing

Non-Operating 0 to 95% Non-condensing

Altitude

Operating 0ft to 10,000ft/3048m

Non-Operating 0ft to 50,000ft/15240m

Temperature

Operating 32F/0

o

C to 95F/35oC

Non-Operating 5F/-15oC to 113F/45oC

Safety Approvals

Certifications UL60950_1 , CSA C22.2, CE, RoHS Compliant

A. Mounting Bracket
B. Rear Outlets (IEC 320 C13)
C. Circuit Breaker

D. External Site Ground
E. AC Inlet (IEC 320 C20)
F. Cord Retention Tray Screw Holes

Back View

Basic Series ( 1U 20A )

7

For more information on CyberPower products, visit www.CPSww.com

A. AC Inlet (IEC 320 C14)
B. Circuit Breaker
C. External Site Ground
D. Front Outlets
E. Cord Retention Tray

Screw Holes

A. Bracket Screw Hole
B. Keyhole Mount Peg

Screw Holes

Product Features

Front View

Technical Specifications

Model Name

PDU10BVHVIEC16F
PDU10BVHVIEC20F

Input

Voltage 200~240V

Max Current 10 A

Regulatory Derated
Input Current

10 A

Circuit Breaker 10A

Plug Type IEC 320 C14

Power Cord Length 10 ft /3.05m

Output

Voltage 200~240V

Max Current 10 A

Outlet Type(Quantity)

IEC 320 C13(16)

IEC 320 C19(4)/C13(16)

Indicators

LED Indicators N/A

Meter Readout N/A

Physical

Dimension (WxDxH)

1.75"x1.5"x24" / 4.45x3.81x60.96 cm

1.75"x1.5"x36" / 4.45x3.81x91.44 cm

Environmental

Humidity

Operating 0 to 95% Non-condensing

Non-Operating 0 to 95% Non-condensing

Altitude

Operating 0ft to 10,000ft/3048m

Non-Operating 0ft to 50,000ft/15240m

Temperature

Operating 32F/0

o

C to 95F/35oC

Non-Operating 5F/-15oC to 113F/45oC

Safety Approvals

Certifications UL60950_1 , CSA C22.2, CE, RoHS Compliant

Back View

A

B

C

E

E

D

B

A

B

A

Basic Series ( 0U 10A )

8

For more information on CyberPower products, visit www.CPSww.com

Product Features

Front View

Technical Specifications

Model Name

PDU20BVHVIEC16F
PDU20BVHVIEC20F
PDU20BVHVIEC24F
PDU20BVHVIEC32F
PDU20BVHVIEC38F

Input

Voltage 200~240V
Max Current 20 A
Regulatory Derated

Input Current

16 A

Circuit Breaker 16 A
Plug Type IEC 320 C20
Power Cord Length 10 ft /3.05m

Output

Voltage 200~240V
Max Current 20 A

Outlet Type(Quantity)

IEC 320 C13(16)

IEC 320 C19(4)/C13(16)
IEC 320 C19(4)/C13(20)
IEC 320 C19(4)/C13(24)
IEC 320 C19(4)/C13(30)

Indicators

LED Indicators N/A
Meter Readout N/A

Physical

Dimension (WxDxH)

1.75" x 1.5" x 24" / 4.45 x 3.81 x 60.96 cm

1.75" x 1.5" x 36" / 4.45 x 3.81 x 91.44 cm

1.75" x 1.5" x 48" / 4.45 x 3.81 x 121.92cm

1.75" x 1.5" x 60" / 4.45 x 3.81 x 152.40 cm

1.75" x 1.5" x 70" / 4.45 x 3.81 x 177.80 cm

Environmental

Humidity

Operating 0 to 95% Non-condensing

Non-Operating 0 to 95% Non-condensing

Altitude

Operating 0ft to 10,000ft/3048m

Non-Operating 0ft to 50,000ft/15240m

Temperature

Operating 32F/0

o

C to 95F/35oC

Non-Operating 5F/-15oC to 113F/45oC

Safety Approvals

Certifications UL60950_1 , CSA C22.2, CE, RoHS Compliant

B

A

A

B

Back View

High Voltage Type:

A. AC Inlet (IEC 320 C20)
B. Circuit Breaker
C. External Site Ground
D. Front Outlets
E. Front Outlets
F. Cord Retention Tray

Screw Holes

A. Bracket Screw Hole
B. Keyhole Mount Peg

Screw Holes

A

B

C

D

E

F

F

F

F

Basic Series ( 0U 20A )

9

For more information on CyberPower products, visit www.CPSww.com

Product Features

Front View

Technical Specifications

Model Name

PDU20MVHVIEC24F
PDU20MVHVIEC30F
PDU20MVHVIEC38F

Input

Voltage 200~240V
Max Current 20 A
Regulatory Derated

Input Current

16 A

Circuit Breaker 16 A
Plug Type IEC 320 C20
Power Cord Length 10 ft /3.05m

Output

Voltage 200~240V
Max Current 20 A

Outlet Type(Quantity)

IEC 320 C19(4)/C13(20)
IEC 320 C19(6)/C13(24)
IEC 320 C19(8)/C13(30)

Indicators

LED Indicators N/A
Meter Readout Amperage

Physical

Dimension (WxDxH)

1.75" x 1.5" x 48" / 4.45 x 3.81 x 121.92 cm

1.75" x 1.5" x 60" / 4.45 x 3.81 x 152.40 cm

1.75" x 1.5" x 70" / 4.45 x 3.81 x 177.80 cm

Environmental

Humidity

Operating 0 to 95% Non-condensing

Non-Operating 0 to 95% Non-condensing

Altitude

Operating 0ft to 10,000ft/3048m

Non-Operating 0ft to 50,000ft/15240m

Temperature

Operating 32F/0

o

C to 95F/35oC

Non-Operating 5F/-15oC to 113F/45oC

Safety Approvals

Certifications UL60950_1 , CSA C22.2, CE, RoHS Compliant

Back View

High Voltage Type:

A. AC Inlet (IEC 320 C20)
B. Circuit Breaker
C. External Site Ground
D. Front Outlets
E. Meter Readout
F. Front Outlets
G. Cord Retention Tray

Screw Holes

A. Bracket Screw Hole
B. Keyhole Mount Peg

Screw Holes

A

B

C

D

F

E

G

G

G

G

B

A

A

B

Meter Series ( 0U 20A )

K01-0000264-01

CyberPower Systems, Inc.

www.CPSww.com