CyberPower PDU20SW10ATNET, PDU15SW10ATNET, PDU15M10AT, PDU20M10AT, PDU20SWT10ATNET User Manual

User Manual

Automatic
Transfer
Switch

Table of Contents

Overview

................................................................................................... 1

Model List

................................................................................................. 1

Product Contents

.............................................................................. 2

For 1U Series

........................................................................................... 2

For 2U Series

........................................................................................... 3

Product Features

............................................................................... 4

Front/Rear Panel Description (1U 15A series)

............................ 4

Technical Specifications

...................................................................... 4

Front/Rear Panel Description (1U 20A series)

............................ 5

Technical Specifications

...................................................................... 5

Front/Rear Panel Description (2U series)

..................................... 6

Technical Specifications

...................................................................... 6

Installation Guide

............................................................................. 7

For 1U Series

........................................................................................... 7

For 2U Series

........................................................................................... 8

Replacing LCD Panel

............................................................................. 9

Electrical Installation

............................................................................ 9

Network Installation

.......................................................................... 10

(Performed when Remote Management Card is installed) ........................ 10

Power Cord Retention Clip Installation- For IEC type ATS

... 11

Input Power Cord Retention Cable Clip Installation

......... 11

Power Cord Retention Clip Installation

................................. 12

Removing the Power Cord Retention Clip

............................ 13

Operation

............................................................................................... 13

Remoting Management

.................................................................... 13

Web

.................................................................................................... 13

Telnet and SSH

................................................................................ 13

SNMP

.................................................................................................. 13

Local Management

............................................................................. 14

LCD Operation

................................................................................. 14

LED Indicators

................................................................................. 14

Environmental Monitoring (optional)

.................................... 15

Device Reset

.................................................................................... 15

Unattended/Automatic Shutdown

......................................... 15

Firmware Upgrade

......................................................................... 16

ATS PDU

............................................................................................ 16

LCD

.................................................................................................... 17

RMCARD

............................................................................................ 19

Troubleshooting

............................................................................... 19

Conformance Approvals

.......................................................... 20

Customer Service & Warranty

........................................... 20

Appendix A-Hyper Terminal

................................................ 22

Appendix B-Power Device Network Utility

........... 23

1

©2014. CyberPower Systems, Inc. All rights reserved.

Switched Series Metered/Monitored Series

1U 1U

PDU15SW10ATNET PDU15M10AT
PDU20SW10ATNET PDU20M10AT
PDU20SWT10ATNET PDU20MT10AT
PDU20SWHVT10ATNET PDU20MHVT10AT
PDU15SWHVIEC12ATNET PDU15MHVIEC12AT
PDU20SWHVIEC10ATNET PDU20MHVIEC10AT
PDU20SWHVCEE10ATNET* PDU20MHVCEE10AT*

2U 2U

PDU30SWT17ATNET PDU30MT17AT
PDU30SWHVT19ATNET PDU30MHVT19AT

*Selected models may not be available in certain regions. Please contact your
CyberPower sales team for more information.

Overview

Model List

CyberPower Automatic Transfer Switches PDUs with dual input for power provide
redundant and increased reliability for critical devices with a single power plug.
Users can define the preferred input power source. When a selected source is
unstable or unavailable, the ATS PDU will switch to the second power source to
constantly provide power to connected devices. The entire ATS PDU series are
designed with LED and LCD interfaces for users to easily observe power status and
device load. On-site power management is accomplished as users can configure
power settings, via LCD interface, according to local power condition. Available in
both switched and metered/monitored configurations, users have a broad base of
options to select the ATS PDU that best fits their needs.

Safety Precautions
Read the following before installing or operating the
Automatic Transfer Switches (ATS PDU):

• Use only the supplied hardware to attach the mounting brackets.

• The ATS PDU must be plugged into a single phase three-wire, grounded

outlet on a circuit that is protected by a fuse or circuit breaker. For
PDU15xxxxx series, please use 15A circuit protector. For PDU20xxxxx series,
please use 20A circuit protector. For PDU30xxxxx series, please use 30A
circuit protector. Connection to any other type of power outlet may result in
a electrocution hazard.

• Do not use extension cords or adapters with these ATS PDUs.

• Never install an ATS PDU or associated wiring or equipment during a lightning

storm.

• Ensure that the power cord, plug, and socket are in good condition.

To prevent the risk of fire or electrocution, this ATS PDU should be installed in a
temperature and humidity controlled indoor area free of conductive contaminants. Do
not install this ATS PDU where excessive moisture or heat is present.

Before using, please check to ensure the package contains all the items shown below.
If there are missing parts, please contact your local CyberPower sales team for
technical support.

Check

2

©2014. CyberPower Systems, Inc. All rights reserved.

Below items only provided with IEC type ATS PDU

IEC Socket Power Cord Stand
(2 for 10 outlets, 3 for 12 outlets)

Power Cord Retention
Cable Clip (18 for 10 outlets,
21 for 12 outlets)

Power Cord 10 feet
IEC-320 C13/C14 x 2
(PDU15SWHVIEC12ATNET/
PDU15MHVIEC12AT Model Only)

Power Cord 10 feet
IEC-320 C19/C20 x 2
(PDU20SWHVIEC10ATNET/
PDU20MHVIEC10AT Model Only)

Cable Tie (18 for 10 outlets,
21 for 12 outlets)

(M3x4) Screws (15 for 10 outlets,
22 for 12 outlets)

For 1U Series

Product Contents

ATS PDU

Cable Ties: Qty. 18 for 10 outlets,
21 for 12 outlets

RJ45/DB9 Serial Port
Connection Cable

Jumper (Switched type only)

Mounting Bracket x 2

24 (M4x8) Bracket Mounting Screws
(Includes eight spares)

6 (M5x12) Rack Mounting Screws/
6 Washers (Includes two spares for each)

2 (M3x4) Cord Retention Tray
Mounting Screws

Cord Retention Tray

User Manual / Registration Card / CD

Registration
Card

C

yber

Pow

er

R
e

l
i
a

b
i
l

i
t
y.

Q
u

a
l

i
t
y.

Va
l

u
e

.

R

U

s
e

r
's

M

a

n

u

a
l

3

©2014. CyberPower Systems, Inc. All rights reserved.

Below items only provided with IEC type ATS

IEC Socket Power Cord Stand x 4

Power Cord Retention
Cable Clip x 27

Cable Tie x 2729 (M3x4) Screws

For 2U Series

Product Contents

ATS PDU

Cable Ties: Qty. 30

RJ45/DB9 Serial Port
Connection Cable

Jumper (Switched type only)

Mounting Bracket x 2

24 (M4x8) Bracket Mounting Screws
(Includes eight spares)

6 (M5x12) Rack Mounting Screws/
6 Washers (Includes two spares for each)

Cord Retention Tray X 2

4 (M3x4) Cord Retention
Tray Mounting Screws

User Manual / Registration Card / CD

Registration
Card

C

yber

Pow

er

R

e
l
i
a
b

i
l
i
t

y.

Q
u
a

l
i
t

y.

Va

l
u
e
.

R

U
s

e
r
's

M

a
n

u

a

l

4

©2014. CyberPower Systems, Inc. All rights reserved.

Provides SNMP Card Communication

Expansion Port

Select

Enter

PDU20SWHVIEC10ATNET

A

B

Source Output

- Normal

- Warning

- Overload

QCN-0000003-00

Serial Port

1 2 3 4 5 6 7 8 9 10

100-120V
50/60 Hz

Source BSource A

87654321

Source A

1211109

200-240V

50/60 Hz

Source B

A B C D E F

G

H I K

J

H I K

J

Product Features

Technical Specifications

Switched Series Metered Series

Model Name PDU15SW10ATNET PDU15SWHVIEC12ATNET PDU15M10AT PDU15MHVIEC12AT

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 12A 12A(UL)/10A(CE) 12A 12A(UL)/10A(CE)

Plug Type (2) NEMA 5-15P (2) IEC-320 C14 (2) NEMA 5-15P (2) IEC-320 C14

Power Cord Type SR (14 AWG) Socket SR (14 AWG) Socket

Power Cord Length 10 ft/3.05 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current 12A 12A(UL)/10A(CE) 12A 12A(UL)/10A(CE)

Outlet Type NEMA 5-15R IEC-320 C13 NEMA 5-15R IEC-320 C13

Outlet Number 10 12 10 12

Transfer Time

Typical: 8-12ms

16ms max @ 60Hz/ 18ms max @ 50Hz

Management and Communications

Multifunction LCD Readout Voltage, Frequency, Load, Current, HW/FW Version, Network Information

Software PowerPanel® Business Edition

SNMP/ HTTP Capable Yes, with RMCARD203

Yes, with optional
RMCARD202/203

Connectivity RJ45 (Serial Port)

Sensor Capable Optional

Physical

Dimension (W x H x D) 17.05" x 1.75" x 9.3"/433mm x 44mm x 236mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 13100 ft/4000 m

Temperature 32

o

F to 113oF/0oC to 45oC

Safety Approvals

Certifications

UL 60950-1
FCC Class A

UL 60950-1

CE, FCC Class A

UL 60950-1
FCC Class A

UL 60950-1

CE, FCC Class A

* All specifications are subject to change without notice.

NEMA Type

IEC Type

A. SNMP/HTTP Network Slot

Allow users to remotely control and monitor the ATS PDU when installed
with CyberPower’s Remote Management Card.

B. Serial Port (RJ45 modular port)

Use serial port to connect with PC and execute local control of the ATS PDU.

C. Source Indicator

Indicates Source A or B is in use. When both sources are normal, selected
source shows constant green LED while another source shows blinking
green LED.

D. Output Indicator

Indicates load condition of the ATS PDU.

E. Multifunction LCD Readout

Display various ATS PDU information such as power and load conditions.

F. Select Button

Use to control the LCD display and toggle through the available
informational options.

G.Enter Button

Use to choose selected items, enter to next level menu or return to
previous menu.

H. AC Inlet/AC Power Cord

Use to connect ATS PDU to utility power or UPS.

I. Ground Stud

Use to ground the ATS PDU.

J. AC Output Receptacles

Provides power distribution for connected equipment.

K. Outlet Indicator (switched series only)

When the LED is on, the outlet is providing power to connected equipment.

Front/Rear Panel Description (1U 15A series)

5

©2014. CyberPower Systems, Inc. All rights reserved.

Provides SNMP Card Communication

Expansion Port

Select

Enter

PDU20SWT10ATNET

A

B

Source Output

- Normal

- Warning

- Overload

QCN-0000002-00

Serial Port

Provides SNMP Card Communication

Expansion Port

Select

Enter

PDU20SWHVIEC10ATNET

A

B

Source Output

- Normal

- Warning

- Overload

QCN-0000003-00

Serial Port

1 2 3 4 5 6 7 8 9 10

100-120V
50/60 Hz

Source BSource A

Source A

87654321

200-240V

50/60 Hz

Source B

9 10

87654321

Source A

1211109

200-240V

50/60 Hz

Source B

A B C D E F

G

A B C D E F

G

1 2 3 4 5 6 7 8 9 10

100-120V
50/60 Hz

Source BSource A

H I K

J

H I K

J

H I K

J

H I K

J

Product Features

Front/Rear Panel Description (1U 20A series)

NEMA Type

IEC Type

A. SNMP/HTTP Network Slot

Allow users to remotely control and monitor the ATS PDU when installed
with CyberPower’s Remote Management Card.

B. Serial Port (RJ45 modular port)

Use serial port to connect with PC and execute local control of the ATS PDU.

C. Source Indicator

Indicates Source A or B is in use. When both sources are normal, selected
source shows constant green LED while another source shows blinking green
LED.

D. Output Indicator

Indicates load condition of the ATS PDU.

E. Multifunction LCD Readout

Display various ATS PDU information such as power and load conditions.

F. Select Button

Use to control the LCD display and toggle through the available informational
options.

G. Enter Button

Use to choose selected items, enter to next level menu or return to previous
menu.

H. AC Inlet/AC Power Cord

Use to connect ATS PDU to utility power or UPS.

I. Ground Stud

Use to ground the ATS PDU.

J. AC Output Receptacles

Provides power distribution for connected equipment.

K. Outlet Indicator (switched series only)

When the LED is on, the outlet is providing power to connected equipment.

Technical Specifications

Switched Series Metered Series

Model Name

PDU20SW10ATNET

PDU20SWT10ATNET

PDU20SWHVT10ATNET

PDU20M10AT

PDU20MT10AT

PDU20MHVT10AT

PDU20SWHVCEE10ATNET PDU20MHVCEE10AT

PDU20SWHVIEC10ATNET PDU20MHVIEC10AT

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 16A

Plug Type

(2) NEMA 5-20P
(2) NEMA L5-20P

(2) NEMA L6-20P
(2) IEC 309 16A
(2) IEC-320 C20

(2) NEMA 5-20P
(2) NEMA L5-20P

(2) NEMA L6-20P
(2) IEC 309 16A
(2) IEC-320 C20

Power Cord Type SR (12AWG)

SR (12AWG)

SR (12 AWG)

SR (12AWG)

Socket Socket

Power Cord Length 10 ft/3.05 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current 16A

C13: 12A (UL)
10A (CE)
C19: 16A

16A

C13: 12A (UL)
10A (CE)
C19: 16A

Outlet Type NEMA 5-20R

(8) IEC C13/
(2) IEC C19

NEMA 5-20R

(8) IEC C13/
(2) IEC C19

Outlet Number 10 8+2 10 8+2

Transfer Time

Typical: 8-12ms

16ms max @ 60Hz/ 18ms max @ 50Hz

Management and Communications

Multifunction LCD Readout Voltage, Frequency, Load, Current, HW/FW Version, Network Information

Software PowerPanel® Business Edition

SNMP/ HTTP Capable Yes, with RMCARD203

Yes, with optional
RMCARD202/203

Connectivity RJ45 (Serial Port)

Sensor Capable Optional

Physical

Dimension (W x H x D) 17.05" x 1.75" x 9.3"/433mm x 44mm x 236mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 13100 ft/4000 m

Temperature 32oF to 113oF/0oC to 45oC

Safety Approvals

Certifications

UL 60950-1
FCC Class A

UL 60950-1
FCC Class A

UL 60950-1
FCC Class A

UL 60950-1
FCC Class A

UL 60950-1

CE, FCC Class A

UL 60950-1

CE, FCC Class A

* All specifications are subject to change without notice.

6

©2014. CyberPower Systems, Inc. All rights reserved.

Select

Enter

PDU20SWT10ATNET

A

B

Source Output

- Normal

- Warning

- Overload

QCN-0000002-00

Provides SNMP Card Communication

Expansion Port

Select

Enter

PDU20SWHVIEC10ATNET

A

B

Source Output

- Normal

- Warning

- Overload

QCN-0000003-00

Serial Port

Provides SNMP Card Communication

Expansion Port

Serial Port

Select

Enter

PDU30SWT17ATNET

A

B

Source Output

- Normal

- Warning

- Overload

QCN-0000005-00

B1

B2

B3

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

Source A

Source B

100-120V
50/60 Hz

Bank3 , 24A

17

Bank1 , 20A

Bank2 , 20A

L5-30R

1 2 3 4 5 6 7 8 9 10

100-120V
50/60 Hz

Source BSource A

87654321

9 10

87654321

Source A

1211109

200-240V

50/60 Hz

Source B

Source A

Source B

200-240V
50/60 Hz

87654321 9

1716151413121110 18

Bank3 , 24A

Bank1 , 20A

Bank2 , 20A

19

L6-30R

G

A B C D E F

G

J

J

H I K

J

H I K

J

A B

C D E

F

G

H

H

K

K

J

I

I

J

L

L

NEMA Type

IEC Type

A. SNMP/HTTP Network Slot

Allow users to remotely control and monitor the ATS PDU when installed
with CyberPower’s Remote Management Card.

B. Serial Port (RJ45 modular port)

Use serial port to connect with PC and execute local control of the ATS PDU.

C. Source Indicator

Indicates Source A or B is in use. When both sources are normal, selected source
shows constant green LED while another source shows blinking green LED.

D. Output Indicator

Indicates load condition of the ATS PDU.

E. Multifunction LCD Readout

Display various ATS PDU information such as power and load conditions.

F. Select Button

Use to control the LCD display and toggle through the available
informational options.

G. Enter Button

Use to choose selected items, enter to next level menu or return to
previous menu.

H. AC Inlet/AC Power Cord

Use to connect ATS PDU to utility power or UPS.

I. AC Output Receptacles

Provides power distribution for connected equipment.

J. Outlet Indicator (switched series only)

When the LED is on, the outlet is providing power to connected equipment.

K. Circuit Breaker

Provides output overload protection.

L. Ground Stud

Use to ground the ATS PDU.

Technical Specifications

Switched Series Metered Series

Model Name PDU30SWT17ATNET PDU30SWHVT19ATNET PDU30MT17AT PDU30MHVT19AT

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 24A

Plug Type (2) NEMA L5-30P (2) NEMA L6-30P (2) NEMA L5-30P (2) NEMA L6-30P

Power Cord Type SR (10 AWG)

Power Cord Length 10 ft/3.05 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current

5-20R: 16A
L5-30R: 24A

C13: 12A
C19: 16A
L6-30R: 24A

5-20R: 16A
L5-30R: 24A

C13: 12A
C19: 16A
L6-30R: 24A

Derated Output Current
(each bank)

20A

Bank Number 2

Outlet Type

(16) NEMA 5-20R
(1) NEMA L5-30R

(16) IEC C13
(2) IEC C19
(1) NEMA L6-30R

(16) NEMA 5-20R
(1) NEMA L5-30R

(16) IEC C13
(2) IEC C19
(1) NEMA L6-30R

Outlet Number 17 19 17 19

Circuit Breaker Yes

Transfer Time

Typical: 8-12ms

16ms max @ 60Hz/ 18ms max @ 50Hz

Management and Communications

Multifunction LCD Readout Voltage, Frequency, Load, Current, HW/FW Version, Network Information

Software PowerPanel® Business Edition

SNMP/ HTTP Capable Yes, with RMCARD203

Yes, with optional
RMCARD202/203

Connectivity RJ45 (Serial Port)

Sensor Capable Optional

Physical

Dimension (W x H x D) 17.05" x 3.5" x 9.3"/433mm x 88mm x 236mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 13100 ft/4000 m

Temperature 32oF to 113oF/0oC to 45oC

Safety Approvals

Certifications UL 60950-1, FCC Class A

* All specifications are subject to change without notice.

Product Features

Front/Rear Panel Description (2U series)

7

©2014. CyberPower Systems, Inc. All rights reserved.

Installation Guide

For 1U Series

Step 1. Mounting Bracket Installation

Use the Mounting Bracket Screws (16) provided to attach the
Mounting Brackets (2) to the ATS PDU.

Step 2. ATS PDU Mounting

Use the Washers (4) and Screws (4) provided to secure the ATS PDU
to your existing rack system.

Step 3: Cord Retention Tray Installation (optional)

Attach the Cord Retention Tray to the ATS PDU with the 4
Cord Retention Tray Mounting that are provided.

Use the Cable Ties provided to fasten each power cord to the
Cord Retention Tray.

Please only use the provided screws for the entire installation process.

8

©2014. CyberPower Systems, Inc. All rights reserved.

Step 1. Mounting Bracket Installation

Use the Mounting Bracket Screws (16) provided to attach the
Mounting Brackets (2) to the ATS PDU.

Step 2. ATS PDU Mounting

Use the Washers (4) and Screws (4) provided to secure the ATS PDU
to your existing rack system.

Step 3. Cord Retention Tray Installation (optional)

Attach the Cord Retention Tray to the ATS PDU with the 8 Cord
Retention Tray Mounting Screws provided.

Use the Cable Ties provided to fasten each power cord to the
Cord Retention Tray.

Installation Guide

For 2U Series

9

©2014. CyberPower Systems, Inc. All rights reserved.

Replacing the LCD Panel

Step 1. Use a slotted screwdriver to gently lift out the LCD panel.

Step 2. Disconnect the cable connector.

Step 1. Receptacle evaluation

Ensure that the plug type of your ATS PDU unit matches the receptacles

that you are using.

Electrical Installation

The ATS PDU must be plugged into a three-wire, grounded utility receptacle or
a UPS that is connected to a grounded utility receptacle. The utility receptacle
must also be connected to an appropriate branch circuit/main with fuse or circuit
breaker protection. Connection to any other type of receptacle may result in an
electrocution hazard.

Step 2. Plug the ATS PDU into the utility receptacle and/or UPS.

Step 3. Attach equipment

It is extremely important not to exceed the ATS PDU's maximum current
load (as outlined in the Specifications section). In order to determine
total load, use the LCD diaplay on the front of the ATS PDU to monitor
the load being attached.

Installation Guide

10

©2014. CyberPower Systems, Inc. All rights reserved.

Step 1. Attach the LAN Cable

Using a CAT5 RJ45 cable, attach one end to the Ethernet port on the RMCard,
and the other end to a network port.

Step 2. Establish the ATS PDU IP address

Assigning an IP address to the CyberPower ATS PDU requires the user to have
an available IP address that is valid on the respective network. If an available
IP address is unknown, contact the network administrator to obtain one. The
default IP is 192.168.20.177 and the default for the DHCP function is on.

There are multiple methods for setting up the IP address of the ATS PDU. Please
follow the instructions below for the method that is appropriate for your application.

Please make sure the ATS PDU is powered on during this process.

Option 1 (recommended): Power Device Network Utility

1. Use the included “Software Installation CD” to install the Power Device Network
Utility program.

2. Open the Power Device Network Utility software (Start => Power Device
Network Utility).

3. Highlight the ATS PDU device from the list and select Edit and Setup device
=>Assisted Setup from the menu.

4. Configure the IP Address, Subnet Mask, and Gateway Address to match your
network settings.

5. Enter the user name and password of the ATS PDU device at the Authentication menu.

Note : The default username is “cyber” and the default password is “cyber”.
For further information and installation instructions, see Appendix B.

Option 2: DHCP Server

1. Ask your administrator if there is DHCP server on the LAN.

2. Make sure the DHCP is Enabled.

3. Make sure the network connection is ready and power on the ATS PDU.

4. The ATS PDU will obtain an IP address from the DHCP server automatically.

Option 3: Address Resolution Protocol (ARP) Command

1. Obtain the MAC address from the sticker on the ATS PDU.

2. Open a command prompt as an administrator and type the following:

“arp -s [available IP address] [MAC address of ATS]”.
Example: arp -s 192.168.20.240 00-0C-15-00-00-01
IP Address MAC Address

3. Use the Ping command to assign a size of 123 bytes to the IP.

* Type in “ping 192.168.20.240 -l 123” then press Enter
* If the replies are received, your computer can communicate with the IP address

Option 4: Hyper Terminal or Terminal Emulator
In order for Hyper Terminal to interface with the ATS PDU, the PC/server must be
connected directly to the ATS PDU via the serial port.

1. Use the included RJ45/DB9 serial port connection cable, attach one end to the

serial port on the front of the ATS PDU, and the other end to the PC/server.

2. Open the Hyper Terminal software on your PC and select a name and icon for the
connection.

3. Setup the COM port settings using the following values

* Bits per second: 38400
* Data bits: 8
* Parity: None
* Stop bits: 1
* Flow control: None

4. Press Enter to enter the Authentication menu.

5. Enter the user name and password of the ATS PDU device at the Authentication menu.

Note: The default username is “cyber” and the default password is “cyber”.
For further information and configuration via Hyper Terminal, see Appendix
A-Hyper Terminal.

Network Installation

(Performed when a Remote Management Card is installed)

Installation Guide

11

©2014. CyberPower Systems, Inc. All rights reserved.

Power Cord Retention Clip Installation- For IEC type ATS PDU

Input Power Cord Retention Cable Clip Installation

Step 1. Remove the screw next to the inlet.

Step 2. Attach the Cable Tie on the ATS PDU and secure it with the screw removed

in the previous step.

Step 3. Place a Power Cord Retention Cable Clip on the power cord. Align and

insert the Cable Tie into the Cable Clip as shown in the figure below.

Step 4. Push the Power Cord Retention Cable Clip until it touches the plug and

fasten the Retention Cable Clip like the figure below.

Installation Guide

12

©2014. CyberPower Systems, Inc. All rights reserved.

Step 2. Attach the IEC Socket Power Cord Stand on the ATS PDU and secure it with

the screws removed in the previous step.

Step 3. Attach Cable Tie on the IEC Socket Power Cord Stand and secure it with the

provided screw.

Step 4. Place a Power Cord Retention Cable Clip on the power cord. Align and

Insert the Cable Tie into the Cable Clip as shown in the figure below.

Step 5. Push the Power Cord Retention Cable Clip until it touches the plug and

fasten the Retention Cable Clip like the figure below.

Power Cord Retention Clip Installation

Step 1. Remove the screws next to the outlet where IEC Socket Power Cord Stand

will be installed.

Installation Guide

13

©2014. CyberPower Systems, Inc. All rights reserved.

Step 2. Remove the Power Cord Retention Clip by pulling the clip (show in the

image below) to the left.

Operation

Remote Management

The remote management function provides for monitoring of the ATS PDU
operational information, controlling outlets and utilizing SNMP functionality.

Web

Remote management can be performed via web interface. To access the web
interface, please follow the instructions below:

1. Enter the IP address of the ATS PDU into a web browser (Internet Explorer, Firefox).

2. Enter the user name and password of the ATS PDU device at the authentication screen.

Note: The default username is “cyber” and the default password is “cyber”.
For additional information about the features and functionality of CyberPower
Management Console, please refer to the software Installation CD.

Telnet and SSH

The CyberPower ATS PDU provides Telnet and Secure Shell (SSH) as Remote Management
methods. Telnet uses user name and password as basic security while SSH has a higher
security level with encryption of the transmitted packets including user name, password, and
data. Configure the Setting of Telnet and SSH on the Web Interface. The default user name
and password is cyber/cyber.

SNMP

The CyberPower ATS PDU supports SNMPv1 and SNMPv3 Remote Management protocols.
Download the CyberPower MIB file and add it to a SNMP-supporting management software.
Default read/write community is public/privated for SNMPv1. SNMPv3 provides a higher
security level than SNMPv1 by encrypting the transmitted packet. Configure the settings of
the SNMPv1/SNMPv3 on Web Interface .

Removing the Power Cord Retention Clip

Step 1. Remove the Power Cord Retention Clip by pushing it to the right as shown

in the figure below.

Installation Guide

14

©2014. CyberPower Systems, Inc. All rights reserved.

LED Indicators

Indicator Status Description

Source

Solid Green Selected source and power condition is normal.

Flashing Green Bankup source and power condition is normal.

Orange Power condition is abnormal.

Load

Green The aggregate current of each bank is normal.

Orange Near overload.

Red Overload.

Tx/Rx

Off The ATS PDU power is off.

On (Green) The ATS PDU power is on.

Flashing

Receiving/transmitting data packet.

Reset finished.

LINK

On Indicates the ATS PDU is connected to the LAN.

Off Indicates the ATS PDU is not connected to the LAN.

Outlet

On The outlet is on and providing power.

Off The outlet is off.

Local Management

LCD Operation

The LCD display provides instant information, such as source condition, voltage and current,
for the ATS PDU. In addition, users can use the interface to configure each PDU parameters
and control each outlet on the switched ATS PDU.

A. Scroll Mode: The ATS PDU information will display in following order

automatically when “Scroll Mode On” is configured.

Source A information

Source B information

Device Load

Bank 1 Current (2U series)

Bank 2 Current (2U series)

Bank 3 Current (2U series)

Environment Status (Displays when the ENVIROSENSOR is connected)

B. Main Menu Map

About

Hardware Version

Firmware Version

Network Information

Serial Number

Settings

Preferred Source A/B/None

Source Configuration

Nominal Voltage

Voltage Range

Freq. Deviation

Sensitivity

Load Configuration

Device

Bank/1/2/3

Overload

Threshold

Near Overload

Threshold
Low Load

Threshold

Outlet Control

Device

Bank/1/2/3

All/Outlet 1-N

Immediate On

Delay On

Immediate Off

Delay Off

Reboot

Delay Reboot

LCD Settings

Brightness

Scroll Mode

Screen Off

Reset/Reboot

Reset All (ATS PDU, RMCARD and LCD)

Reset Except TCP/IP

Reset Account (User Name and Password)

Reboot

Operation

15

©2014. CyberPower Systems, Inc. All rights reserved.

Environmental Monitoring (optional)

The CyberPower ATS PDU with an environment sensor (ENVIROSENSOR) installed,
provides remote temperature and humidity monitoring in a server closet and/or
datacenter. To connect ATS PDU with ENVIROSENSOR, use RJ45 Ethernet Cable
included with the ENVIROSENSOR. Plug one end into the Environmental port
on the RMCARD and the other end into the RJ45 port on the ENVIROSENSOR
(as shown in figures below). When the ATS PDU connected correctly to the
ENVIROSENSOR, users can see the temperature and humidity data with the Web
Interface. For further information regarding ENVIROSENSOR configuration please
refer to the Software Installation CD.

Device Reset

●

To reset all the settings to default locally, use Reset function in the LCD display.

●

To reset all the settings to default remotely, log in Web interface, enter the Reset

page and apply the function.

Unattended/Automatic Shutdown

PowerPanel Business Edition software automatically intitiates a graceful shutdown
on the operating system in an orderly fashion.
PowerPanel must be installed on every computer or server for which the shut
down is to take place. The computer will receive an SNMP message from the
ATS PDU and will perform the shut down according to the instructions provided,
including shut downs at exact time and dates.
Follow the directions below for setting up Unattended/Automatic Shutdown.

Step 1. PC Configuration

1. Install PowerPanel Business Edition Client on every computer/server that will
be part of the shut down process (Follow the instructions in the PowerPanel
Business Edition Client user manual).

2. Configure the settings in PowerPanel Business Edition Client. See the
PowerPanel Business Edition Client User Manual for additional help.

Step 2. ATS PDU Configuration
Verify that the IP address of all computers, that will be part of the shut down
process, are included in the Client List of the web interface (For additional
information, please refer to the user manual in the Software Installation CD).

Step 3. Notification
Notifying the computers of potential outlet shutdowns can be accomplished using
the following methods:

●

Outlets Control Menu: Performing the task of turning off or rebooting outlets

●

Scheduling Menu: Setting the application to perform the task of turning off or

rebooting outlets. The notification will occur prior to the scheduled date/time.

●

Outlet Overload: In the event of ATS PDU overload, notification will be sent prior

to the ATS PDU shutting down.

Operation

16

©2014. CyberPower Systems, Inc. All rights reserved.

By upgrading the Firmware, you can obtain new features, updates and
improvements to existing functionality.

ATS PDU

Update the following file to upgrade the firmware

- cpsatsmafw_xxx.bin

Note that the XXX is not part of the file name but is where the version number in
the filename is given.

Use the following steps to upgrade the firmware.

1. Download the latest firmware from cpsww.com

2. Extract the file to “C:\”

3. Open Hyper Terminal to connect the ATS PDU and use the command “@NEW”

4. The ATS PDU will reboot and show main menu on Hyperterminal.

5. Press “1” to select ATS PDU upgrade

6. Select Transfer > Send File

7. Note that the Ymodem protocol and file “C:\cpsatsmafw_xxx.bin”

are selected in Hyperterminal

Firmware Upgrade

17

©2014. CyberPower Systems, Inc. All rights reserved.

8. The download progress window will open after you click the Send button

9. After uploading the binary file Hyperterminal will show as below

LCD

Update the following file to upgrade the firmware

- cpsatslafw_xxx.bin

Note that the XXX is not part of the file name but is where the version number in
the filename is given.

Use the following steps to upgrade the firmware.

1. Download the latest firmware from cpsww.com

2. Extract the file to “C:\”

3. Open Hyper Terminal to connect the ATS PDU and use the command “@NEW”

4. The ATS PDU will reboot and show main menu on Hyperterminal

5. Press “2” to select LCD upgrade

Firmware Upgrade

18

©2014. CyberPower Systems, Inc. All rights reserved.

6. Press “1”

7. Select Transfer > Send File

8. Note that the Ymodem protocol and file “C:\cpsatslafw_xxx.bin” are

selected in Hyperterminal

9 The download progress window will open after you click the Send button

10. After uploading the binary file, Hyperterminal will be shown as below

You can see if the firmware upgrade is successful by checking the
“CyberPower System Firmware Version” after login.

Firmware Upgrade

19

©2014. CyberPower Systems, Inc. All rights reserved.

Note :

1. Please do not turn the ATS PDU off and ensure the quality of selected
source power when processing firmware upgrade. The ATS PDU will not
perform the ATS function when upgrading firmware.

2. Press “3” to exit the main menu of firmware upgrade.

RMCARD

There are two files to update in order to upgrade the firmware:

- cpssnmpfw_XXX.bin

- cpssnmpdata_XXX.bin

Note that the XXX is not part of the file name but is where the version number
in the filename is given.

Use the following steps to upgrade the firmware.

1. Download the latest firmware from cpsww.com

2. Extract the file to “C:\”

3. Open a command prompt window and navigate to “C:\”

4. Login to the Remote Management Card with FTP command, type

- ftp (after entering ftp mode, ftp> will display in the command prompt as

shown below instead of C:\ )

- ftp> open

- To [current IP of the RMCARD] [port] (for example: To 192.168.22.126 21

[21 is the default ftp port for the RMCARD])

- Input USER NAME and PASSWORD (same as the administrator account in

Web interface default: cyber ; cyber)

5. Upload the cpssnmpfw_XXX.bin, type

- ftp > bin

- ftp > put cpssnmpfw _XXX.bin

6. Upgrade complete, type

- ftp > quit7. The system will reboot after you type “quit”. This reboot will
take approx. 30 seconds

8. Login to the FTP again

- ftp

- ftp> open

- To [current IP of the RMCARD] [port] (for example: To 192.168.22.126 21)

[21 is the default ftp port for theRMCARD])

- Input USER NAME and PASSWORD

9. Upload cpssnmpdata _XXX.bin

- ftp > bin

- ftp > put cpssnmpdata _XXX.bin

10. Upgrade complete , type

- ftp > quit

11. The system will reboot after you type “quit”

Troubleshooting

Problem Possible Cause Solution

ATS PDU outlets do
not provide power to
connected equipment

1. Breaker tripped

2. Power cord is not
properly plugged in

Reset Breaker, check the plug to
insure its connected correctly. If
the problem remains, contact
technical support.

Amperage displayed
on LCD Display
exceeds the units
capability

Overload

The load indicator shows red
when overload. Reduce the load
on the ATS PDU until the overload
is gone. If the problem remains,
contact technical support.

Circuit breakers have
tripped

1. Sustained overload

2. Excessive ambient or
internal temperatures

3. Faulty breaker

Reset Breaker.
If the problem remains, contact
technical support.

Firmware Upgrade

20

©2014. CyberPower Systems, Inc. All rights reserved.

FCC Warning

WARNING!! This equipment has been tested and found to comply with the limits
for a Class A Digital Device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

Any special accessories needed for compliance must be specified in the
instruction.

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Notice: (1) An unshielded-type power cord is required in order to meet FCC
emission limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord by used. (2) Use only
shielded cables to connect I/O devices to this equipment.
Note: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.
SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.

The Class A digital apparatus meets all requirements of the Canadian Interference­Causing Equipment Regulation.
Cet appareil numerique de la class A respecte toutes les exigencies du Reglement
sur le materiel brouilleur du Canada.

Customer Service & Warranty

Product Registration

Thank you for purchasing a CyberPower product. Prompt product registration
entitles coverage under the Limited Warranty and also allows the opportunity to
be notified of product enhancements, upgrades, and other announcements.
Registration is quick and easy at www.CPSww.com under “Support”.

CyberPower International

Feel free to contact our Tech Support department with installation,
troubleshooting, or general product questions.

CyberPower Systems, Inc.
Web: www.cpsww.com

CyberPower Systems (USA), Inc.
Phone: [phone] Toll-free: [phone]
Email: [e-mail]
Web: www.CPSww.com
Add: 4241 12th Avenue E., Suite 400 Shakopee, MN 55379
Hours of Operation: Monday-Friday 8:00 AM-5:00 PM (CST)

Limited Warranty

Read the following terms and conditions carefully before using the CyberPower
ATS PDU series. By using the Product, you consent to be bound by and become a
party to the terms and conditions of this Limited Warranty. If you do not agree to
the terms and conditions of this Warranty, you should return the Product for a full
refund prior to using it.

Who Is Providing This Warranty?

CyberPower Systems, Inc. provides this Limited Warranty.

What Does This Warranty Cover?

This warranty covers defects in materials and workmanship in the Product under
normal use and conditions.

What Is The Period of Coverage?

CyberPower provides a 3-Year limited warranty to the original purchaser who
owns the Product.

Conformance Approvals

21

©2014. CyberPower Systems, Inc. All rights reserved.

Who Is Covered?

This warranty only covers the original purchaser. Coverage ends if you sell or
otherwise transfer the Product.

How Do You Get Service?

1. You can use the contact information mentioned above for instructions.

2. When you contact CyberPower, identify the Product, the Purchase Date, and
the item(s) of Connected Equipment.

3. You must provide a purchase receipt (or other proof of the original purchase)
and provide a description of the defect.

What Will We Do To Correct Problems?

CyberPower will inspect and examine the Product.
If the Product is defective in material or workmanship, CyberPower will repair or
replace it at CyberPower's expense, or, if CyberPower is unable to or decides not
to repair or replace the Product (if defective) within a reasonable time,
CyberPower will refund to you the full purchase price you paid for the Product
(purchase receipt showing price paid is required).

Who Pays for Shipping?

We pay when we send items to you; you pay when you send items to us.

What Are Some Things This Warranty Does Not Cover?

1. This Warranty does not cover any software that is damaged or needs to be replaced
due to the failure of the Product or any data that is lost as a result of the failure or
the restoration of data or records, or the reinstallation of software.

2. This Warranty does not cover or apply to: misuse, modification, operation or
storage outside environmental limits of the Product or the equipment
connected to it, nor for damage while in transit or in storage, nor if there has
been improper operation or maintenance, or use with items not designed or
intended for use with the Product, such as laser printers, appliances, aquariums,
medical or life support devices, etc.

What Are The Limitations?

1. This Warranty does not apply unless the Product and the equipment that
was connected to it were connected to properly wired and grounded outlets
(including compliance with electrical and safety codes of the most current
electrical code), without the use of any adapters or other connectors.

2. The Product must have been plugged directly into the power source and the
equipment connected to the Product must be directly connected to the Product
and not "daisy-chained" together in serial fashion with any extension cords,
another Product or device similar to the Product, surge suppressor, or power
tap. Any such installation voids the Limited Warranty.

3. The Product and equipment connected to it must have been used properly
in a suitable and proper environment and in conformance with any license,
instruction manual, or warnings provided with the Product and the equipment
connected to it.

4. The Product must have been used at all times within the limitations on the
Product's VA capacity.

5. The sole and exclusive remedies of the Initial Customer are those provided by
this Warranty

Customer Service & Warranty

22

©2014. CyberPower Systems, Inc. All rights reserved.

Appendix A-Hyper Terminal

Hyper Terminal software can be used for basic ATS PDU configuration. It utilizes a
text-based interface and menu system. Navigation through the interface is done
by typing the number of the menu option and pressing the Enter key.
Note: The session will timeout and logout after 3 minutes of inactivity. Menu
options are shown below:

[Main Menu]

1. Utility Configuration

2. Outlet Manager (Switched Series Only)

3. Load Configuration

4. Network Settings

5. System Configuration

6. Account Settings

7. Configure System to Default

8. Logout

[Utility Configuration]

1. Preferred Source: A

2. Sensitivity: High

3. Voltage Range: Medium

4. Frequency Deviation: 1 Hz

5. Nominal Voltage: 230 V

6. Wide Voltage Range: 30 V

7. Medium Voltage Range: 23 V

8. Narrow Voltage Range: 16 V

9. Set Load Restriction

[Outlet Manager]

1. Outlet Control

2. Outlet Configuration

[Load Configuration]

1. Device Threshold Configuration

2. Bank 1 Threshold Configuration

3. Bank 2 Threshold Configuration

4. Bank 3 Threshold Configuration

[Network Setting]

Physical MAC Address: 00-0C-15-00-00-01

1. System IP: 192.168.20.240

2. Subnet Mask: 255.255.255.0

3. Default Gateway: 192.168.20.254

4. DHCP: Enabled

5. Http Port: 80

6. Http Access: Enabled

[System Configuration]

1. Name: PDU15SW10ATNET

2. Location: Server Room

3. Contact: Administrator

[Account Setting]

1. Administrator

[Configure System to Default]

Sure to Configure System to Default

1. Reset ATS

2. Reset ATS (TCP/IP Settings Reserved)

23

©2014. CyberPower Systems, Inc. All rights reserved.

Appendix B-Power Device Network Utility

Overview

The CyberPower Power Device Network Utility is an easy-to-use interface which is
used for establishing IP addresses on CyberPower ATS PDUs.

Installation

Step 1. Insert the CD labeled “Software Installation CD” into the CD/DVD drive.
Step 2.Select Power Device Network Utility from the installation menu (Shown in
Figure 1.).

Step 3. Select Next in the software wizard.
Step 4. Choose an installation directory and user settings.
Select Next (Shown in Figure 2.).

Step 5. Select Next to comfirm the settings and install.
Step 6. Select Close to finalize the installation.

Figure 1. Installation Menu

Figure 2. Installation folder and settings

Launch Program

To launch the Power Device Network Utility and get started, select Programs from
the Start menu in Windows and locate the new folder and icons for Power Device
Network Utility. Select Power Device Network Utility from the program folder
(Shown in Figure 3.).

Figure 3. Power Device Network Utility

24

©2014. CyberPower Systems, Inc. All rights reserved.

Appendix B-Power Device Network Utility

Getting Started

The Power Device Network Utility scans the network for devices with MAC addresses
that match CyberPower network hardware. Once found, the device(s) can then be
figured with a specific IP address, subnet mask, and gateway address. This allows
the device(s) to function properly on the network and interface with CyberPower
Management Console.
Step 1. Select the appropriate ATS PDU from the Equipment List (Shown in Figure 4.).

Note: If the ATS PDU does not appear on the list, click the Refresh button to rescan the
network. If it still does not appear, ensure that the ATS PDU is turned on and is installed
correctly.
Pressing Stop will cancel the scan/refresh process.

Note: If your computer has a software firewall installed, you may see a Windows
Security Alert message (Shown in Figure 5.).
In Windows XP SP2, the default firewall alert message is shown as Figure 5. You
need to allow the Power Device Network Utility access through the firewall.

Figure 4. Equipment List

Figure 5. Windows Security Alert

Step 2. Assign a valid IP Address to the ATS PDU

With the appropriate device selected from the Equipment List, open the Network
Settings menu (shown in Figure 6.) [Tools=>Device Setup]. In the Device Network
Setting Menu, enter a valid IP address, subnet mask, and gateway address to
setup the ATS device.

Figure 6. Network Setting Menu (Device Setup)

25

©2014. CyberPower Systems, Inc. All rights reserved.

Step 3. Authentication
Enter the user name and password of the ATS PDU at the Authentication menu
(shown in Figure 7.)

Note: The default username is “cyber” and the default password is “cyber”.

Advanced Settings

Timeout Settings
The Timeout Setting (Shown in Figure 8.). [Edit=>Timeout Settings] is used to
specify the wait time when scanning for network ATS PDUs. When there are many
devices on the local network, it may take extended periods of time to locate all
the devices. The timeout function is used to limit the search time.
The default setting is 3 seconds. Valid values are 3 to 60 seconds.

Figure 7. Authentication screen

Figure 8. Timeout Setting

Appendix B-Power Device Network Utility

CyberPower Systems, Inc.

www.CPSww.com

K01-0000322-01