Page 1
Power
Distribution
Unit
User Manual
K01-0000082-01
4241 12th Ave E #400,
Shakopee, MN 55379
1-877-297-6937
www.CPSww.com
Page 2
Table of Contents
Model List ......................................................1
PDU Naming Convention ............................. 1
Package Contents ........................................ 2
Safety Precautions ....................................... 2
Installation .................................................... 3
Horizontal Installation ....................... 3
Vertical Installation with Brackets ...
4
Vertical Installation Keyhole Mounts (0U models only) ...
5
Cord Retention Tray installation ......
5
Meter Configuration ..........................
5
Electrical Installation ........................ 6
Troubleshooting ........................................... 6
Product Features
Technical Specification ................................ 7
Basic Series ....................................... 7
Metered Series ...................................
9
Basic Series (0U) ...............................
10
Metered Series (0U) ...........................
11
Warranty & Service .......................................12
Page 3
Model List:
Check
Before using, please check to ensure the package contains all the
items shown above. If there are missing parts please contact
CyberPower technical support at www.CPSww.com or call 1-877297-6937.
Safety Precautions Read
the following before installing or operating
the Power Distribution Unit (PDU):
1. Use only the supplied hardware to attach the mounting brackets.
2. The PDU must only be plugged into a three-wire, grounded outlet on a
circuit protected by a fuse or circuit breaker. Connection to any other type
of power outlet may result in a shock hazard.
3. Do not use extension cords or adapters with this PDU.
4. Never install a PDU, or associated wiring or equipment, during a lightning
storm.
5. Check that the power cord, plug, and socket are in good condition.
6. CAUTION! To prevent the risk of fire or electric shock, this PDU
should be
installed in a temperature and humidity controlled indoor area free of
conductive contaminants. Do not install this PDU where excessive
moisture or heat is present..
Basic Series:
PDU15B8R
PDU15B10R
PDU15B12R
PDU20B8R
PDU20B10R
PDU20B12R
PDU20BT8R
PDU20BT10R
PDU20BT12R
PDU15B2F8R
PDU15B2F10R
PDU15B2F12R
PDU15B4F8R
PDU15B4F10R
PDU15B4F12R
PDU15B6F8R
PDU15B6F10R
PDU15B6F12R
PDU20B2F8R
PDU20B2F10R
PDU20B2F12R
PDU20B4F8R
PDU20B4F10R
PDU20B4F12R
PDU20B6F8R
PDU20B6F10R
PDU20B6F12R
PDU20BT2F8R
PDU20BT2F10R
PDU20BT2F12R
PDU20BT4F8R
PDU20BT4F10R
PDU20BT4F12R
PDU20BT6F8R
PDU20BT6F10R
PDU20BT6F12R
Metered Series:
PDU15M2F8R
PDU15M2F10R
PDU15M2F12R
PDU20M2F8R
PDU20M2F10R
PDU20M2F12R
PDU20MT2F8R
PDU20MT2F10R
PDU20MT2F12R
Basic Series (0U):
PDU15BV14F
PDU15BV16F
PDU15BV20F
PDU15BV28F
PDU15BV32F
PDU20BV14F
PDU20BV16F
PDU20BV20F
PDU20BV28F
PDU20BV32F
PDU20BVT14F
PDU20BVT16F
PDU20BVT20F
PDU20BVT28F
PDU20BVT32F
Metered Series (0U):
PDU15MV20F
PDU15MV26F
PDU15MV32F
PDU20MV20F
PDU20MV26F
PDU20MV32F
PDU20MVT20F
PDU20MVT26F
PDU20MVT32F
PDU Naming Convention:
1. Amperage:
2. Series:
3. Rack Space:
4. Input Voltage:
5. Plug Type:
6. Outlet Number Front
7. Outlet Number Rear
8. Network Management
PDU XX M V HV T F R NET
1 2 3 4 5 6 7 8
Amperage – 15A, 20A, 30A
B: =Basic M: =Metered
SW: = Switched
NULL: =Horizontal V:= Vertical
NULL: =120V HV:= High Voltage – 200V to 230V
NULL: =NEMA 5-15P / 5-20P
T: = Twist (NEMA L5-L6 Plug)
IEC:= (IEC C14/C20)
Number of Outlets followed by F – Example 8F
Number of Outlets followed by R – Example 8R
NET
For inf ormation on Cy berpower product s, visit www.C PSww.com For inf ormation on Cy berpower product s, visit www.C PSww.com
1 2
Package Contents
PDU (1)
Cord Retention Tray
(
1/2/3/4 pcs - varies by model)
Horizontal Installation
Used (1 set)
Vertical Installation
Used (1 set)
Mounting Brackets
Vertical Mounting Brackets (1 set)
(for 0U models only)
Keyhole Mounting Pegs (2pcs)
with Screws M4 X 8 (2pcs)
(for 0U models only)
Bracket Mounting
Screws M4 X 8 (4pcs)
Cord Retainer Clips (8/10/12/14/16/
20/24/30/32/38 pcs - varies
by model)
for Cord Retention Tray
Documentation:
User Manual
Power
Distribution
Unit
User Manual
Product Registration Card
Product
Registration
Card
Cord Retention Tray
Mounting Screws M3 X 6
(
4/8/12/16 pcs - varies by model)
Ground Screw M4 X 6 (1 pcs)
Page 4
Installation
Horizontal Installation (1U models only)
Vertical Installation with Brackets
Step 1 – Mounting bracket installation
Install the screws (M4 X 8) in holes diagonal from each other.
Step 2 – PDU Mounting
Install the PDU using fasteners compatible with the rack.
Step 2 – PDU Mounting
Install the PDU using fasteners compatible with the rack.
Vertical Installation with Brackets (0U models only)
Step 1 – Mounting bracket installation
Attach the Vertical Mounting Brackets to the PDU with the 4 supplied
Bracket Mounting Screws (M4 X 8).
Step 2 – PDU Mounting
Install the PDU using fasteners compatible with the rack.
For inf ormation on Cy berpower product s, visit www.C PSww.com For inf ormation on Cy berpower product s, visit www.C PSww.com
3 4
Step 1 – Mounting bracket installation
Install the screws (M4 X 8) in holes diagonal from each other.
Page 5
Vertical Installation with Keyhole Mounts (0U Models) Electrical Installation
Ensure that the plug type of your PDU unit (e.g. NEMA 5-15P, NEMA 520P, NEMA L5-30P) matches the wall receptacle type that you are using.
Step 1 – Receptacle evaluation
PDU must be plugged into a three-wire, grounded wall receptacle only.
The wall receptacle must also be connected to an appropriate branch
circuit/main with fuse or circuit breaker protection. Connection to any
other type of wall receptacle may result in a shock hazard.
CAUTION!!
Step 2 – Plug the PDU into the wall receptacle
Step 3 – Attach equipment
Before attaching equipment, it is important to calculate the total load that you
will be placing on the PDU. It is extremely important not to exceed the PDU's
maximum current load (as outlined in the Specifications section). In order to
determine your total load, simply add up the amperage of your devices and
ensure that it does not exceed the unit’s capacity.
Troubleshooting
Problem Possible Cause Solution
PDU Outlets do not
provide power to
connected
equipment
1. Open breaker
2. Loose power cord
Reset Breaker check if
plug is completely
connected.
If the problem remains
contact tech support.
Amperage displayed
on Amperage Meter
exceeds the unit’s
capability (Metered
type only)
1. Overload
2. Amperage meter is
damaged
The meter will flash
when overloaded.
Reduce the load on the
PDU until the overload
is gone.
If the problem remains
contact tech support.
Circuit breaker has
tripped
1. Sustained overload
2.
Excessive ambient or
internal temperatures.
3. Faulty breaker
Reset Breaker.
If the problem remains
contact tech support.
Align the the Keyhole Mounts to the Keyhole Slots on the rack.
Insert and slide down to lock firmly into place.
Step 2 – PDU Mounting
Step 1 – Keyhole Mount installation
Attach the Keyhole Mounting Pegs to the PDU with the 2 supplied
Bracket Mounting Screws (M4 X 8).
For i nfo rm ati on on Cy be rpo wer p rod ucts, vi si t w ww.CPS ww.c om F or in forma tio n on Cyber pow er pr odu ct s, visit ww w.C PSw w.c om
5 6
Cord Retention Tray installation
(Optional for both horizontal and vertical installations)
Attach the Cord Retention Tray to the PDU with the 4 supplied Cord
Retention Tray Mounting Screws (M3 X 6).
Attach the Cord Retainer Clips to the Cord Retention Tray.
Meter Configuration
Use a screwdriver to gently remove the LED Meter. Rotate the LED Meter
90 degrees, and insert back into the PDU.
!
Note
Depending on installation method (vertical or horizontal),
the LED Meter may need to be rotated, before installation,
for proper orientation.
Page 6
Basic Series Basic Series
Product Features
Front View
Back View
A B
A. Mounting Bracket
B. Rear Outlets
C. External Site Ground
A. Mounting Bracket
B. Circuit Breaker
A B C D
D. AC Power Cord
E.
EE
D. AC Power Cord
E. Cord Retention Tray
Screw Holes
EE
Product Features
Front View
Back View
A B C D
A B
C
A. Mounting Bracket
B. Rear Outlets
C. External Site Ground
A. Mounting Bracket
B. Circuit Breaker
C. Front Outlets
D. AC Power Cord
E. Cord Retention Tray
Screw Holes
EE
Technical Specifications Technical Specifications
For inf ormation on Cy berpower product s, visit www.C PSww.com For inf ormation on Cy berpower product s, visit www.C PSww.com
7 8
Model Name
PDU15B8R
PDU15B10R
PDU15B12R
PDU20B8R
PDU20B10R
PDU20B12R
PDU20BT8R
PDU20BT10R
PDU20BT12R
Input
Voltage
Max current
15 A
Circuit Breaker 15 A
Plug Type NEMA 5-15P NEMA 5-20P NEMA L5-20P
Output
Voltage
Current 15 A
Outlet Type NEMA 5-15R
Indicators
LED Indicators
Meter Readout
Physical
Environmental
Humidity
Altitude
Temperature
Safety Approvals
Certifications
Warranty
ETL (test followed UL 1363)
RoHS
Lifetime
Operatin
g 0 to 95% Non-condensing
Non-Operating 0 to 95% Non-condensing
Operating 0ft to 10,000ft
Non-Operating 0ft to 50,000ft
Operating 32F to 95F
Non-Operating 5F to 113F
N/A
17.5" x 1.5" x 1.75" / 44.5 x 3.81 x 4.45 cm
15 ft
N/A
100 ~ 125 V
20 A
NEMA 5-20R
100 ~ 125 V
20 A
20 A
Power Cord Length
Dimension (WxDxH)
Model Name
PDU15B2F8R
PDU15B2F10R
PDU15B2F12R
PDU15B4F8R
PDU15B4F10R
PDU15B4F12R
PDU15B6F8R
PDU15B6F10R
PDU15B6F12R
PDU20B2F8R
PDU20B2F10R
PDU20B2F12R
PDU20B4F8R
PDU20B4F10R
PDU20B4F12R
PDU20B6F8R
PDU20B6F10R
PDU20B6F12R
PDU20BT2F8R
PDU20BT2F10R
PDU20BT2F12R
PDU20BT4F8R
PDU20BT4F10R
PDU20BT4F12R
PDU20BT6F8R
PDU20BT6F10R
PDU20BT6F12R
Input
Voltage
Max current 15 A
Circuit Breake
15 A
Plug Type NEMA 5-15P NEMA 5-20P NEMA L5-20P
Output
Voltage
Current 15 A
Outlet Type NEMA 5-15R
Indicators
LED Indicators
Meter Readout
Physical
Environmental
H
umidity
Altitude
Temperature
Safety Approvals
Certifications
Warranty
ETL (test followed UL 1363)
RoHS
Lifetime
Operating 0 to 95% Non-condensing
Non-Operating 0 to 95% Non-condensing
Operating 0ft to 10,000ft
Non-Operating 0ft to 50,000ft
Operating 32F to 95F
Non-Operating 5F to 113F
N/A
17.5" x 2.25" x 1.75" / 44.5 x 5.72 x 4.45 cm
N/A
100 ~ 125 V
20 A
NEMA 5-20R
100 ~ 125 V
20 A
20 A
15 ft
Power Cord Length
Dimension (WxDxH)
Page 7
Metered Series
Product Features
Front View
Back View
A B C D
A B
C D
A. Mounting Bracket
B. Rear Outlets
C. External Site Ground
A. Mounting Bracket
B. Circuit Breaker
C. LED Meter Readout
D. Front Outlets
D. AC Power Cord
E. Cord Retention Tray
Screw Holes
EE
Technical Specifications
For inf ormation on Cy berpower product s, visit www.C PSww.com For inf ormation on Cy berpower product s, visit www.C PSww.com
9 10
Basic Series (0U)
Technical Specifications
Product Features
Front View Back View
A
B
C
D
E
E
D
D
D
B
A
A
B
A. AC Power Cord
B. Circuit Breaker
C. External Site Ground
D. Cord Retention Tray
Screw Holes
E. Front Outlets
A. Bracket Screw Hole
B. Keyhole Mount Peg
Screw Holes
Model Name
PDU15M2F8R
PDU15M2F10R
PDU15M2F12R
PDU20M2F8R
PDU20M2F10R
PDU20M2F12R
PDU20MT2F8R
PDU20MT2F10R
PDU20MT2F12R
Input
Voltage
Max Current 15 A
Circuit Breaker 15 A
Plug Type NEMA 5-15P NEMA 5-20P NEMA L5-20P
Power Cord Length
Output
Voltage
Current 15 A
Outlet Type NEMA 5-15R
Fiters & Protection
EMI/RFI Filtration
Surge Suppression
Indicators
LED Indicators
Meter Readout
Physical
Environmental
Humidity
Altitude
Temperature
Safety Approvals
Certifications
Warranty
100 ~ 125 V
20 A
20 A
15 ft
100 ~ 125 V
20 A
NEMA 5-20R
N/A
N/A
N/A
Amperage
17.5" x 2.25" x 1.75" / 44.5 x 5.72 x 4.45 cm
ETL (test followed UL 1363)
RoHS
Lifetime
Operating 0 to 95% Non-condensing
Non-Operating 0 to 95% Non-condensing
Operating 0ft to 10,000ft
Non-Operating 0ft to 50,000ft
Operating 32F to 95F
Non-Operating 5F to 113F
Dimension (WxDxH)
Model Name
PDU15BV14F
PDU15BV16F
PDU15BV20F
PDU15BV28F
PDU15BV32F
PDU20BV14F
PDU20BV16F
PDU20BV20F
PDU20BV28F
PDU20BV32F
PDU20BVT14F
PDU20BVT16F
PDU20BVT20F
PDU20BVT28F
PDU20BVT32F
Input
Voltage
Max Current 15 A
Circuit Breaker 15 A
Plug Type NEMA 5-15P NEMA 5-20P NEMA L5-20P
Output
Voltage
Current 15 A
Outlet Type NEMA 5-15R
Indicators
LED Indicators
Meter Readout
Physical
Environmental
Humidity
Altitude
Temperature
Safety Approvals
Certifications
Warranty
Lifetime
Operating 0 to 95% Non-condensing
Non-Operating 0 to 95% Non-condensing
Operating 0ft to 10,000ft
Non-Operating 0ft to 50,000ft
Operating 32F to 95F
Non-Operating 5F to 113F
1.75" x 1.5" x 24" / 4.45 x 3.81 x 60.96 cm
1.75
" x 1.5" x 36" / 4.45 x 3.81 x 91.44 cm
1.75" x 1.5" x 48" / 4.45 x 3.81 x 121.92 cm
1.75" x 1.5" x 60" / 4.45 x 3.81 x 152.40 cm
1.75" x 1.5" x 70" / 4.45 x 3.81 x 177.80 cm
ETL (test followed UL 1363)
RoHS
N/A
N/A
NEMA 5-20R
20 A
100 ~ 125 V
20 A
20 A
10 ft
100 ~ 125 V
Power Cord Length
Dimension (WxDxH)
Page 8
Metered Series (0U)
Technical Specifications
Product Features
Front View
Back View
A
B
C
D
E
E
D
D
D
B
A
A
B
F
A. AC Power Cord
B. Circuit Breaker
C. External Site Ground
D. Cord Tray Screws
Holes
E. Front Outlets
F. LED Meter Readout
A. Bracket Screw Hole
B. Keyhole Mount Peg
Screw Holes
For inf ormation on Cy berpower product s, visit www.C PSww.com For inf ormation on Cy berpower product s, visit www.C PSww.com
11 12
Model Name
PDU15MV20F
PDU15MV26F
PDU15MV32F
PDU20MV20F
PDU20MV26F
PDU20MV32F
PDU20MTV20F
PDU20MTV26F
PDU20MTV32F
Input
Voltage
Max Current 15 A
Circuit Breaker 15 A
Plug Type NEMA 5-15P NEMA 5-20P NEMA L5-20P
Output
Voltage
Current 15 A
Outlet Type NEMA 5-15R
Indicators
LED Indicators
Meter Readout
Physical
Environmental
Humidity
Altitude
Temperature
Safety Approvals
Certifications
Warranty
100 ~ 125 V
20 A
20 A
10 ft
N/A
100
~ 125 V
20 A
NEMA 5-20R
ETL (test followed UL 1363)
RoHS
Lifetime
Operating 0 to 95% Non-condensing
Non-Operating 0 to 95% Non-condensing
Operating 0ft to 10,000ft
Non-Operating 0ft to 50,000ft
Operating 32F to 95F
Non-Operating 5F to 113F
Amperage
1.75" x 2.25" x 48" / 4.45 x 5.72 x 121.92 cm
1.75" x 2.25" x 60" / 4.45 x 5.72 x 152.40 cm
1.75" x 2.25" x 70" / 4.45 x 5.72 x 177.80 cm
Power Cord Length
Dimension (WxDxH)
Product Registration
Thank you for purchasing a CyberPower product. Prompt product
registration entitles coverage under the Limited Warranty, and also
allows the opportunity to be notified of product enhancements, upgrades,
and other announcements.
Registration is quick and easy at www.cpsww.com/register .
Need Additional Help?
Feel free to contact our Tech Support department with installation,
troubleshooting, or general product questions.
CyberPower Technical Support
Phone: 1-877-297-6937
Email: tech@cpsww.com
Web: www.CPSww.com
Mail: 4241 12th Avenue E, Suite 400 Shakopee, MN 55379
Hours of Operation: Monday – Friday, 8:00am – 5:00pm (CST)
Limited Warranty
Read the following terms and conditions carefully before using the
CyberPower PDU(the “Product”). By using the Product you consent to
be bound by and become a party to the terms and conditions of this
Limited Warranty (together referred to as this “Warranty”). If you do not
agree to the terms and conditions of this Warranty, you should return the
Product for a full refund prior to using it.
Who is Providing this Warranty?
CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited
Warranty.
What Does This Warranty Cover?
This warranty covers defects in materials and workmanship in the
Product under normal use and conditions.
What is the Period of Coverage?
This Warranty is for as long as the original owner owns the Product.
Who Is Covered?
This warranty only covers the original purchaser.
Coverage ends if you sell or otherwise transfer the Product.
How Do You Get Service?
1. Call us at (877) 297-6937 or write to us at Cyber Power Systems
(USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379 or
send us an e-mail message at claims@cyberpowersystems.com
for instructions.
2. When you contact CyberPower, identify the Product,
the Purchase
Date, and the item(s) of Connected Equipment. Have information
on all applicable insurance
or other resources of recovery/payment
that are available to the Initial Customer and Request a Claim
Number.
3. You must provide a purchase receipt (or other proof of the original
purchase) and provide a description of the defect.
4. Pack and ship the product to CyberPower and, if requested, the
item(s) of Connected Equipment, a repair cost estimate for the
damage to the Connected Equipment, and all claim forms that
CyberPower provides to you. Show the Claim Number on the
shipping label or include it with the product. You must prepay all
shipping costs, you are responsible for
packaging and shipment,
and you must pay the cost of the repair estimate.
What Will We Do To Correct Problems?
CyberPower will inspect and examine the Product.
If the Product is defective in material or workmanship, CyberPower
will repair or replace it at CyberPower's expense, or, if CyberPower
is unable to or decides not to repair or replace the Product
(if defective) within a reasonable time, CyberPower will refund to you
the full purchase price you paid for the Product (purchase receipt
showing price paid is required).
Who Pays For Shipping?
We pay when we send items to you; you pay when you send items
to us.
Page 9
What Are Some Things This Warranty Does Not Cover?
1. This Warranty does not cover any software that was damaged or
needs to be replaced due to the failure of the Product or any data
that is lost as a result of the failure or the restoration of data or
records, or the reinstallation of software.
2. This Warranty does not cover or apply to: misuse, modification,
operation or
storage outside environmental limits of the Product or
the equipment connected to it, nor for damage while in transit or in
storage, nor if there has been improper operation or maintenance,
or use with items not designed
or intended for use with the Product,
such as laser printers, appliances, aquariums, medical or life
support devices, etc.
What are the Limitations?
1. This Warranty does not apply unless the Product and the
equipment that was connected to it were connected to properly
wired and grounded outlets (including compliance with electrical
and safety codes of the most current electrical code), without the
use of any adapters or other connectors.
2. The Product must have been plugged directly into the power
source and the equipment connected to the Product must be
directly connected to the Product and not “daisy-chained” together
in serial fashion with any extension cords, another Product or
device similar to the Product, surge suppressor, or power tap.
Any such installation voids the Limited Warranty.
3. The Product and equipment connected to it must have been used
properly in a suitable and proper environment and in conformance
with any license, instruction manual, or warnings provided with the
Product and the equipment connected to it.
4. The Product must have been used at all times within the limitations
on the Product's VA capacity.
5. The sole and exclusive remedies of the Initial Customer are those
provided by this Warranty.
Contact Information
CyberPower Systems, Inc.
4241 12th Ave. East
Suite 400
Shakopee, MN 55379
Phone: (952) 403-9500
Toll-free: (877) 297-6937
CyberPower is the warrantor under this Limited Warranty.
You may also contact CyberPower on the web at CPSww.com.
For inf ormation on Cy berpower product s, visit www.C PSww.com For inf ormation on Cy berpower product s, visit www.C PSww.com
13 14
Loading...