CyberPower PDU15SWHVIEC8FNET, PDU20SWHVIEC8FNET, PDU20SW8FNET, PDU20SWT8FNET, PDU15MV16FNET User Manual

User Manual

Power
Distribution
Unit

Table of Contents

Model List ...........................................................1

Introduction ........................................................1

Package Contents ....................................................... 1

For 1U Series ........................................................ 1

For 0U Series ........................................................ 2

For 2U Series ........................................................ 3

Safety Precautions ..................................................... 3

Proruct Features ........................................................ 4

1U 15A Series ....................................................... 4

Technical Specifications ....................................... 4

1U 20A Series ....................................................... 5

Technical Specifications ....................................... 5

0U 15A Series ....................................................... 6

Technical Specifications ....................................... 6

0U 20A Series ....................................................... 7

Technical Specifications ....................................... 7

0U 30A Series ....................................................... 8

Technical Specifications ....................................... 8

2U Series .............................................................. 9

Technical Specifications ....................................... 9

Installation Guide ................................................10

Horizontal Installation ............................................... 10

For 1U Model ....................................................... 10

For 2U Model ....................................................... 11

Vertical Installation .................................................. 13

For 1U Model ....................................................... 13

For 0U Model with Bracket .................................. 13

For 0U Model with Keyhole Mount ..................... 15

Electrical Installation ................................................. 15

Network Installation .................................................. 16

Operation ............................................................ 17

Metered Readout ..................................................... 17

Basic Operation .................................................... 17

PDU Status Screen................................................ 17

Current Level ................................................ 17

Input Voltage ................................................ 17

Power ........................................................... 17

IP Address .................................................... 17

Outlet Control (switched series only) .......... 17

LED Reversal (0U series only) ....................... 17

Environmental Monitoring (optional) ...................... 18

LED Indicators ........................................................... 18

Device Reset ............................................................. 18

Remote Management .............................................. 18

Unattended/Automatic Shutdown ........................... 19

Firmware Upgrade...............................................19

Troubleshooting .................................................. 20

Frequently Ask Questions (FAQ) ..........................20

Conformance Approvals ......................................20

Customer Service & Warranty .............................21

Product Registration ................................................. 21

CyberPower International ........................................ 21

Limited Warranty ..................................................... 21

Appendix A-Hyper Terminal ................................22

Appendix B-Power Device Network Utility...........23

Overview .................................................................. 23

Installation ................................................................ 23

Launch Program ....................................................... 24

Getting Started ......................................................... 24

Advanced Settings .................................................... 25

1

For more information on CyberPower products, visit www.CPSww.com

1U Switched Series

PDU15SW8FNET
PDU15SWHVIEC8FNET
PDU20SW8FNET
PDU20SWT8FNET
PDU20SWHVIEC8FNET

1U Monitored Series

PDU15M8FNET
PDU15MHVIEC8FNET
PDU20M8FNET
PDU20MT8FNET
PDU20MHVIEC8FNET

0U Switched Series

PDU15SWV16FNET
PDU20SWVT24FNET
PDU20SWVHVT24FNET
PDU30SWVT24FNET
PDU30SWVHVT24FNET

0U Monitored Series

PDU15MV16FNET
PDU20MVT24FNET
PDU20MVHVT24FNET
PDU30MVT24FNET
PDU30MVHVT24FNET

2U Switched Series

PDU30SWT16FNET
PDU30SWHVT16FNET

2U Monitored Series

PDU30MT16FNET
PDU30MHVT16FNET

Package Contents

(For 1U Series)

Model List

Introduction

PDU

6 (M3x6) Cord Retention
Tray Mounting Screws
(Includes two spares)

6 (M5x12) Screws / 6 Washers
(Includes two spares for each)

RJ45/DB9 Serial Port
Connection Cable

Power Cord 10 feet,
IEC-320 C19/ IEC-320 C20
(PDU20SWHVIEC8FNET/
PDU20MHVIEC8FNET Model Only)

Mounting Bracket: 2 short & 2 long

10 (Flat Head M4x8) Bracket Mounting
Screws (Includes two spares)

Power Cord 10 feet,
IEC-320 C13/IEC-320 C14
(PDU15SWHVIEC8FNET/
PDU15MHVIEC8FNET Model Only)

Cord Retention Tray

Cable Ties / Qty. 10 User Manual / Registration Card / CD

Documentation

Registration
Card

C

yber

Pow

er

R
e

l
i
a

b
i
l

i
t
y.

Q
u

a
l
i

t
y.

Va

l
u
e

.

R

U
s

e

r
's

M

a

n

u
a

l

2

For more information on CyberPower products, visit www.CPSww.com

Package Contents

(For 0U Series 16 Outlets/24 Outlets)

Introduction

PDU

6 (Flat Head M4x4) Bracket Mounting
Screws (Includes two spares)

Mounting Brackets x 2

2 Keyhole Mounting Pegs
with 4 (M4x5) Screws
(Includes two spares)

6 (M5x12) Screws/6 Washers
(Includes two spares for each)

Cord Retention Tray Mounting
Screws (M3x6)/Qty. 10 for 16
Outlets/Qty. 14 for 24 Outlets
(Includes two spares)

RJ45/DB9 Serial Port
Connection Cable

Cord Retention Trays Qty. 2
(16 Outlets)/Qty. 3 (24 Outlets)

Cable Ties: Qty. 20 (16 Outlets)
Qty. 30 (24 Outlets)

User Manual / Registration Card / CD

Documentation

Registration
Card

C

yber

Pow

er

R
e

l
i
a
b

i
l
i
t
y.

Q

u

a
l
i
t
y.

Va

l
u

e
.

R

U

s
e

r
's

M

a

n
u

a

l

3

For more information on CyberPower products, visit www.CPSww.com

Safety Precautions

Read the following before installing or operating the
Power Distribution Units (PDU):

• Use only the supplied hardware to attach the mounting brackets.

• The PDU must be plugged into a three-wire, grounded outlet on a circuit that

is protected by a fuse or circuit breaker. For PDU15xxxxx series, please use
15A circuit protector. For PDU20xxxxx series, please use 20A circuit protector.
For PDU30xxxxx series, please use 30A circuit protector. Connection to any
other type of power outlet may result in a shock hazard.

• Do not use extension cords or adapters with this PDU.

• Never install a PDU, or associated wiring or equipment, during a lightning storm.

• Ensure that the power cord, plug, and socket are in good condition.

Package Contents

(For 2U Series)

Introduction

PDU

Mounting Brackets x 2

RJ45/DB9 Serial Port
Connection Cable

10 (M3x6) Cord Retention Tray
Mounting Screws
(Includes two spares)

Cord Retention Trays x2

10 (Flat Head M4x8) Bracket Mounting
Screws (Includes two spares)

6 (M5x12) Screws / 6 Washers
(Includes two spares for each)

Cable Ties: Qty. 20 User Manual / Registration Card / CD

Documentation

Registration
Card

C

yber

Pow

er

R
e

l
i
a

b
i
l

i
t
y.

Q
u
a

l
i
t

y.
Va

l

u
e
.

R

U

s
e

r

's

M

a
n

u

a

l

Check

Before using, please check to ensure the package contains all the
items shown above. If there are missing parts, please contact
your local CyberPower (refer to CyberPower International P.21)
for technical support.

To prevent the risk of fire or electric shock, this PDU should be installed in a
temperature and humidity controlled indoor area free of conductive contaminants. Do
not install this PDU where excessive moisture or heat is present.

4

For more information on CyberPower products, visit www.CPSww.com

Product Features (1U 15A Series)

Front panel description

NEMA Type

IEC Type

Rear panel description

A. Power Cord
B. AC Output Outlets
C. Current Level
D. Input Voltage
E. Power
F. Load Indicator
G. Ethernet Port
H. Tx/Rx Indicator

I. Link Indicator
J. Outlet Indicator

(switched series only)

K. Serial/ ENVIROSENSOR Port

(RJ45 modular port)
L. Select Button
M.PDU Status Screen
N. Reset Button

A

A

Technical Specifications

Switched Series (1U 15A) Monitored Series (1U 15A)

Model Name

PDU15SW8FNET PDU15SWHVIEC8FNET PDU15M8FNET PDU15MHVIEC8FNET

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 12A 12A(UL)/10A(CE) 12A 12A(UL)/10A(CE)

Plug Type NEMA 5-15P IEC-320 C14 NEMA 5-15P IEC-320 C14

Power Cord Type SR (14 AWG) Socket SR (14 AWG) Socket

Power Cord Length 12 ft/3.65 m 10 ft/3.05 m 12 ft/3.65 m 10 ft/3.05 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current 12A 12A(UL)/10A(CE) 12A 12A(UL)/10A(CE)

Outlet Type NEMA 5-15P IEC-320 C13 NEMA 5-15P IEC-320 C13

Outlet Number 8

Networking

Protocol Support TCP/IP, UDP, DHCP, SNMP, HTTP

Connectivity RJ45

Physical

Dimension (HxWxD) 1.75" x 17.05" x 4.41"/44mm x 433mm x 112mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 14700 ft/4500 m

Temperature 32

o

F to 104oF /0oC to 40oC

Safety Approvals

Certifications

UL 60950-1

CSA C22.2

FCC Class A

UL 60950-1

CSA C22.2

CE, FCC Class A

UL 60950-1

CSA C22.2

FCC Class A

UL 60950-1

CSA C22.2

CE, FCC Class A

Warranty

Product Warranty 2 years

A. External Site Ground

5

For more information on CyberPower products, visit www.CPSww.com

Product Features (1U 20A Series)

Front panel description

NEMA Type

IEC Type

Rear panel description

A. Power Cord
B. AC Output Outlets
C. Current Level
D. Input Voltage
E. Power
F. Load Indicator
G. Ethernet Port
H. Tx/Rx Indicator

I. Link Indicator
J. Outlet Indicator

(switched series only)

K. Serial/ ENVIROSENSOR Port

(RJ45 modular port)

L. Select Button
M.PDU Status Screen
N. Reset Button

A. External Site Ground

A

A

Technical Specifications

Switched Series (1U 20A) Monitored Series (1U 20A)

Model Name

PDU20SW8FNET

PDU20SWHVIEC8FNET

PDU20M8FNET

PDU20MHVIEC8FNET

PDU20SWT8FNET PDU20MT8FNET

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 16A

Plug Type

NEMA 5-20P

IEC-320 C20

NEMA 5-20P

IEC-320 C20

NEMA L5-20P NEMA L5-20P

Power Cord Type SR (12 AWG) Socket SR (12 AWG) Socket

Power Cord Length 12 ft/3.65 m 10 ft/3.05 m 12 ft/3.65 m 10 ft/3.05 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current 16A

Outlet Type NEMA 5-20R IEC-320 C13 NEMA 5-20R IEC-320 C13

Outlet Number 8

Networking

Protocol Support TCP/IP, UDP, DHCP, SNMP, HTTP

Connectivity RJ45

Physical

Dimension (HxWxD) 1.75" x 17.05" x 4.41"/44mm x 433mm x 112mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 14700 ft/4500 m

Temperature 32

o

F to 104oF /0oC to 40oC

Safety Approvals

Certifications

UL 60950-1

CSA C22.2

FCC Class A

UL 60950-1

CSA C22.2

CE, FCC Class A

UL 60950-1

CSA C22.2

FCC Class A

UL 60950-1

CSA C22.2

CE, FCC Class A

Warranty

Product Warranty 2 years

6

For more information on CyberPower products, visit www.CPSww.com

A. Power Cord
B. AC Output Outlets
C. Current Level
D. Input Voltage
E. Power
F. Load Indicator
G. Ethernet Port
H. Tx/Rx Indicator
I. Link Indicator
J. Outlet Indicator
(switched series only)
K. Serial /

ENVIROSENSOR Port

(RJ45 modular port)
L. Select Button
M. PDU Status Screen
N. Reset Button

A. Bracket Screw Hole
B. Keyhole Mount Peg
Screw Hole

Technical Specifications

Switched Series (0U 15A) Monitored Series (0U 15A)

Model Name

PDU15SWV16FNET PDU15MV16FNET

Input

Nominal Voltage 100-120V

Frequency 50/60Hz

Derated Input Current 12A

Plug Type NEMA 5-15P

Power Cord Type SR (14 AWG)

Power Cord Length 10 ft/3.05 m

Output

Nominal Voltage 100-120V

Derated Output Current 12A

Outlet Type NEMA 5-15R

Outlet Number 16

Networking

Protocol Support TCP/IP, UDP, DHCP, SNMP, HTTP

Connectivity RJ45

Physical

Dimension (HxWxD) 49" x 2.20" x 1.75"/1245mm x 56mm x 44mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 14700 ft/4500 m

Temperature 32

o

F to 104oF /0oC to 40oC

Safety Approvals

Certifications UL 60950-1, CSA C22.2, FCC Class A

Warranty

Product Warranty 2 years

Product Features (0U 15A Series)

Front panel description Rear panel description

B

A

A

B

7

For more information on CyberPower products, visit www.CPSww.com

A. Power Cord
B. AC Output Outlets
C. Current Level
D. Input Voltage
E. Power
F. Load Indicator
G. Ethernet Port
H. Tx/Rx Indicator
I. Link Indicator
J. Outlet Indicator
(switched series only)
K. Serial /

ENVIROSENSOR Port

(RJ45 modular port)
L. Select Button
M. PDU Status Screen
N. Reset Button

A. Bracket Screw Hole
B. Keyhole Mount Peg
Screw Hole

Product Features (0U 20A Series)

Front panel description Rear panel description

NEMA Type IEC Type

Technical Specifications

Switched Series (0U 20A) Monitored Series (0U 20A)

Model Name

PDU20SWVT24FNET PDU20SWVHVT24FNET PDU20MVT24FNET PDU20MVHVT24FNET

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 16A

Plug Type NEMA L5-20P NEMA L6-20P NEMA L5-20P NEMA L6-20P

Power Cord Type SR (12 AWG)

Power Cord Length 10 ft/3.05 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current 16A

Outlet Type NEMA 5-20R

IEC-320 C13*21/

IEC-320 C19*3

NEMA 5-20R

IEC-320 C13*20/

IEC-320 C19*4

Outlet Number 24 21+3 24 20+4

Networking

Protocol Support TCP/IP, UDP, DHCP, SNMP, HTTP

Connectivity RJ45

Physical

Dimension (HxWxD) 66.53" x 2.20" x 1.75"/1690mm x 56mm x 44mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 14700 ft/4500 m

Temperature 32

o

F to 104oF /0oC to 40oC

Safety Approvals

Certifications UL 60950-1, CSA C22.2, FCC Class A

Warranty

Product Warranty 2 years

B

A

B

A

8

For more information on CyberPower products, visit www.CPSww.com

A. Power Cord
B. AC Output Outlets
C. Input Circuit Breaker
D. Current Level
E. Input Voltage
F. Power
G. Load Indicator
H. Ethernet Port
I. Tx/Rx Indicator
J. Link Indicator
K. Outlet Indicator
(switched series only)
L. Serial /

ENVIROSENSOR Port

(RJ45 modular port)
M. Select Button
N. PDU Status Screen
O. Reset Button

A. Bracket Screw Hole
B. Keyhole Mount Peg
Screw Hole

Product Features (0U 30A Series)

Front panel description Rear panel description

NEMA Type IEC Type

B

A

B

A

Technical Specifications

Switched Series (0U 30A) Monitored Series (0U 30A)

Model Name

PDU30SWVT24FNET PDU30SWVHVT24FNET PDU30MVT24FNET PDU30MVHVT24FNET

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 24A

Plug Type NEMA L5-30P NEMA L5-30P NEMA L5-30P NEMA L5-30P

Power Cord Type SR (10 AWG)

Power Cord Length 10 ft/3.05 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current 24A

Derated Output Current
(each bank)

20A 15A 20A 15A

Bank Number 2

Outlet Type NEMA 5-20R

IEC-320 C13*21/

IEC-320 C19*3

NEMA 5-20R

IEC-320 C13*20/

IEC-320 C19*4

Outlet Number 24 21+3 24 20+4

Circuit Breaker Yes

Networking

Protocol Support TCP/IP, UDP, DHCP, SNMP, HTTP

Connectivity RJ45

Physical

Dimension (HxWxD)

70" x 2.20" x 1.75"/

1778mm x 56mm x 44mm

66.53" x 2.20" x 1.75"/

1690mm x 56mm x 44mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 14700 ft/4500 m

Temperature 32

o

F to 104oF /0oC to 40oC

Safety Approvals

Certifications UL 60950-1, CSA C22.2, FCC Class A

Warranty

Product Warranty 2 years

9

For more information on CyberPower products, visit www.CPSww.com

Technical Specifications

Switched Series (2U) Monitored Series (2U)

Model Name

PDU30SWT16FNET PDU30SWHVT16FNET PDU30MT16FNET PDU30MHVT16FNET

Input

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Frequency 50/60Hz

Derated Input Current 24A

Plug Type NEMA L5-30P NEMA L6-30P NEMA L5-30P NEMA L6-30P

Power Cord Type SR (10 AWG)

Power Cord Length 10 ft/3.05 m 12 ft/3.65 m

Output

Nominal Voltage 100-120V 200-240V 100-120V 200-240V

Derated Output Current 24A

Derated Output Current
(each bank)

20A 15A 20A 15A

Bank Number 2

Outlet Type NEMA 5-20R IEC-320 C13 NEMA 5-20R

IEC-320 C13*12/

IEC-320 C19*4

Outlet Number 16

Circuit Breaker Yes

Networking

Protocol Support TCP/IP, UDP, DHCP, SNMP, HTTP

Connectivity RJ45

Physical

Dimension (HxWxD) 3.5" x 17.05" x 4.41"/88mm x 433mm x 112mm

Environmental

Humidity 0 to 95% Non-condensing

Altitude 14700 ft/4500 m

Temperature 32

o

F to 104oF /0oC to 40oC

Safety Approvals

Certifications UL 60950-1, CSA C22.2, FCC Class A

Warranty

Product Warranty 2 years

Product Features (2U Series)

Front panel description

NEMA Type

IEC Type

A. Power Cord
B. AC Output Outlets
C. Input Circuit Breaker
D. Current Level
E. Input Voltage
F. Power
G. Load Indicator
H. Ethernet Port
I. Tx/Rx Indicator

J. Link Indicator
K. Outlet Indicator

(switched series only)

L. Serial/ ENVIROSENSOR Port

(RJ45 modular port)
M.Select Button
N. PDU Status Screen
O. Reset Button

Rear panel description

A. External Site Ground

Bank 1 , 20A

Bank 2 , 20A

2

1

3

4

5

6

7

8

16

15

14

13

12

11

10

9

Tx/Rx

Link

Amps

Volts

KW

- Warning

- Overload

B1 B2

- Normal

Select

YU0-0000028-00

Reset

100-120VAC
50/60 Hz
24A MAX

B

K

A

G H

C

I

J

LNFD

MOE

Bank 1 , 15A

Bank 2 , 15A

200-240VAC
50/60 Hz
24A MAX
12A MAX PER OUTLET

2

1

3

4

5

6

7

8

16

15

14

13

12

11

10

9

Tx/Rx

Link

Amps

Volts

KW

- Warning

- Overload

B1 B2

- Normal

Select

YU0-0000028-00

Reset

B

K

A

G H

C

I

J

LN

FD

MO

E

A

10

For more information on CyberPower products, visit www.CPSww.com

Installation Guide

Please use only the provided screws through the entire
installation process.

Horizontal Installation

For 1U Model

Step 1. Mounting Bracket Installation

Use the provided Mounting Bracket Screws (8) to attach the SHORT

Mounting Brackets (2) to the PDU.

Step 2. PDU Mounting

Use the supplied Washers (4) and Screws (4) to secure the PDU to your

existing rack system.

If you plan on attaching the Cord Retention Tray to the PDU, you will need
to use the LONG Mounting Brackets (2).

11

For more information on CyberPower products, visit www.CPSww.com

Installation Guide

For 2U Model

Step 1. Mounting Bracket Installation

Use the provided Mounting Bracket Screws (8) to attach the Mounting

Brackets (2) to the PDU.

Step 3. Cord Retention Tray Installation (optional)

Attach the Cord Retention Tray to the PDU with the 4 supplied Cord

Retention Tray Mounting Screws.

Use the provided Cable Ties to fasten each cord to the Cord Retention Tray.

12

For more information on CyberPower products, visit www.CPSww.com

Use the provided Cable Ties to fasten each cord to the Cord Retention Tray.

Step 2. PDU Mounting

Use the supplied Washers (4) and Screws (4) to secure the PDU to
your existing rack system

Step 3. Cord Retention Tray Installation (optional)

Attach the Cord Retention Tray to the PDU with the 8 supplied Cord

Retention Tray Mounting Screws.

Installation Guide

13

For more information on CyberPower products, visit www.CPSww.com

Step 1. Mounting Bracket Installation

Use the provided Mounting Bracket Screws (8) to attach the SHORT

Mounting Brackets (2) to the PDU.

Step 2. PDU Mounting

Use the supplied Washers (2) and Screws (2) to secure the PDU to your

existing rack system.

Installation Guide

Vertical Installation

For 1U Model

For 0U Model with Bracket

Step 1. Mounting Bracket Installation

Use the provided Mounting Bracket Screws (4) to attach the
Mounting Brackets (2) to the PDU.

14

For more information on CyberPower products, visit www.CPSww.com

Step 2. PDU Mounting

Use the supplied Washers (2) and Screws (2) to secure the PDU
to your existing rack system.

Step 3. Cord Retention Tray Installation (optional)

Attach the Cord Retention Tray to the PDU with the supplied
Cord Retention Tray Mounting Screws.

Use the provided Cable Ties to fasten each cord to the Cord Retention Tray.

Installation Guide

15

For more information on CyberPower products, visit www.CPSww.com

Installation Guide

For 0U Model with Keyhole Mount

Step 1. Keyhole Mount Installation

Use the provided Screws (2) to attach the Keyhole Mounting Pegs (2) to

the PDU.

Step 2. PDU Mounting

Align the Keyhole Mounts to the Keyhole Slots on the rack. Insert and slide

down to lock firmly into the place.

Step 1 – Receptacle evaluation

Ensure that the plug type of your PDU unit matches the wall receptacle

type that you are using.

Step 2 – Plug the PDU into the wall receptacle

The PDU must be plugged into a three-wire, grounded wall
receptacle only. The wall receptacle must also be connected to
an appropriate branch circuit/main with fuse or circuit breaker
protection. Connection to any other type of wall receptacle may
result in a shock hazard.

Electrical Installation

16

For more information on CyberPower products, visit www.CPSww.com

Installation Guide

Step 3 – Attach equipment

It is extremely important not to exceed the PDUs maximum current
load (as outlined in the Specifications section). In order to determine
your total load, simply use the Metered Readout on the front of the PDU.

Step 1 – Attach the LAN Cable

Using a CAT5 RJ45 cable, attach one end to the Ethernet port on the front
of the PDU, and the other end to a network port.

Step 2 – Establish the PDU IP address

Assigning an IP address to the CyberPower PDU requires the user to have
an available IP address that is valid on the respective network.
If an available IP address is unknown, contact the network administrator to
obtain one.

The default IP is 192.168.20.177 and the default DHCP function is on.

There are multiple methods for setting up the IP address on the PDU. Please follow
the instructions below for the method that is appropriate for your application.

Please make sure the PDU is powered on during this process.

Option 1 (recommended): Power Device Network Utility

1. Use the included “PDU Software Installation CD” to install the Power Device
Network Utility program.

2. Open the Power Device Network Utility software (Start => Power Device
Network Utility).

3. Highlight the PDU device from the list and select Edit and Setup device =>
Assisted Setup from the menu.

4. Configure the IP Address, Subnet Mask, and Gateway Address to match your
network settings.

5. Enter the user name and password of the PDU device at the Authentication menu.

Note : The default username is “cyber” and the default password is “cyber”.
For further information and installation instructions, see Appendix B.

Option 2: DHCP Server

1. Ask your administrator if there is DHCP server on the LAN.

2. Make sure the DHCP is Enabled.

3. Make sure the network connection is ready and power on the PDU.

4. The PDU will obtain an IP address from the DHCP server automatically.

Option 3: Address Resolution Protocol (ARP) Command

1. Obtain the MAC address from the sticker on the PDU.

2. Open a command prompt as an administrator and type the following:

“arp -s [available IP address] [MAC address of PDU]”.
Example: arp -s 192.168.20.240 00-0c-15-80-00-01
IP Address MAC Address

3. Use the Ping command to assign a size of 123 bytes to the IP.

* Type in “ping 192.168.20.240 -l 123” then press Enter
* If the replies are received, your computer can communicate with the IP address

Option 4: Hyper Terminal or Terminal Emulator
In order for Hyper Terminal to interface with the PDU, the PC/server must be
connected directly to the PDU via the serial port.

1. Use the included RJ45/DB9 serial port connection cable, attach one end to the

serial port on the front of the PDU, and the other end to the PC/ server.

2. Open the Hyper Terminal software on your PC and select a name and icon for the
connection.

3. Setup the COM port settings using the following values

* Bits per second: 9600
* Data bits: 8
* Parity: None
* Stop bits: 1
* Flow control: None

Network Installation

17

For more information on CyberPower products, visit www.CPSww.com

Installation Guide

Operation

4. Type “setup” and press Enter to enter the Authentication menu.

5. Enter the user name and password of the PDU device at the Authentication menu.

Note: The default username is “cyber” and the default password is “cyber”.
For further information and configuration via Hyper Terminal, see Appendix
A-Hyper Terminal.

Metered Readout

Tx/Rx

Link

Amps

Volts

KW

- Warning

- Overload

B1 B2

- Normal

Select

YU0-0000028-00

Reset

The Metered Readout provides instant status updates of
the PDU’s Voltage, Current, Power conditions as well as
the local IP address of the unit to the user. In addition, it
also allows the user to control each outlet of the PDU.

Basic Operation

Screen Selection- To toggle the different status screens, press the Select button
next to the PDU status screen.

• Pressing the Select button once will toggle to the next status screen.

• Pressing and holding the Select button for 3 seconds will display the local IP

address of the unit.

• Pressing and holding the Select button for 6 seconds will enter the outlet

control mode.

PDU Status Screen

•CurrentLevel

The Current Level screen shows the total current draw of
the connected equipment. Units are listed in Amps.

•InputVoltage

The Input Voltage screen measures the AC voltage that the
system is receiving from the utility wall receptacle. This
can be used as a diagnostic tool to identify poor-quality
input power. Units are listed in Volts.

•Power

The Power screen shows the total power that the devices
connected to the PDU consumes. Units are listed in kilowatts.

•IPAddress

The IP Address screen displays the local IP address of the
PDU unit. Note: If the PDU is not connected to a LAN, the
readout will display the default IP address.

•OutletControl(switchedseriesonly)

The Outlet screen shows the condition of each outlet in
sequence. When the outlet is on, the light below this
outlet will be on and a square appears in the upper right
area next to the number of the outlet. To switch the outlet
off, press the Select button once and the square will move
to the lower right. After 1 second, the outlet will turn off.

•LEDReversal(0Useriesonly)

The LED status screen can be set to display upside down from standard through
the Web Interface (as shown in figures below). Note: the decimal point will not
be moved and will instead be on the top if this option is enabled.

Select

KW

Volts

Amps

Tx/Rx

Link

Reset

B1 B2

- Normal

- Warning

- Overload

PDU20SWVT24FNET

Select

KW

Volts

Amps

Tx/Rx

Link

Reset

B1 B2

- Normal

- Warning

- Overload

PDU20SWVT24FNET

KW

Volts

Amps

Reset

B1

KW

Volts

Amps

Reset

B1

18

For more information on CyberPower products, visit www.CPSww.com

Operation

Environmental Monitoring (optional)

CyberPower PDUs along with the environment sensor (ENVIROSENSOR) provide
the function of temperature and humidity monitoring in a server closet and/
or datacenter remotely. To connect the PDU with ENVIROSENSOR, use the RJ45
Ethernet Cable. Plug one end into the Serial/ENVIROSENSOR port on the PDU
and the other end into the RJ45 port on the ENVIROSENSOR (as shown in figures
below). When the PDU correctly connects to the ENVIROSENSOR, users can see
the temperature and humidity data on the Web Interface. For further information
regarding ENVIROSENSOR configuration please refer to the PDU Software
Installation CD.

Device Reset

• To reset all the settings to default except for the IP address, press and hold

the Reset Button for 3 seconds.

• To reset all the settings to default, press and hold the Reset Button for 6 seconds.

Remote Management

The remote management function of the CyberPower PDU provides for
monitoring the PDU vitals, controlling outlets, and utilizing SNMP functionality.
Remote management is performed via the web interface. To access the web
interface, please follow the instructions below:

1. Enter the IP address of the PDU into a web browser (Internet Explorer, Firefox).

2. Enter the user name and password of the PDU device at the authentication screen.

Note: The default username is ”cyber” and the default password is “cyber”.

For additional information about the features and functionality of CyberPower
Management Console, please refer to the PDU Software Installation CD.

8

Select

KW

Volts

Amps

- Normal

- Warning

- Overload

Tx/Rx

Link

Reset

YU0-0000033-01

PDU20SWT8FNET

Select

- Normal

- Warning

- Overload

Tx/Rx

Link

PDU20SWT8FNET

LED Indicators

Indicator Status Description

Load

Green The total PDU power load is normal.

Orange Near overload.

Red Overload.

Tx/Rx

Off The PDU power is off.

On(Green) The PDU power is on.

Flash

Receiving/transmitting data packet.

Reset finished.

LINK

On Indicates the PDU is connected to the LAN.

Off Indicates the PDU is not connected to the LAN.

Outlet

On The outlet is on and providing power.

Off The outlet is off.

19

For more information on CyberPower products, visit www.CPSww.com

Operation

Unattended/Automatic Shutdown

PowerPanel Business Edition software automatically intitiates a graceful shutdown
on the operating system in an orderly fashion.
PowerPanel must be installed on every PC for which the shut down is to take
place. The PC receives SNMP messages directly from the PDU, and these messages
can be scheduled for an exact date/time, or can be performed immediately.
Follow the directions below for setting up Unattended/Automatic Shutdown.

Step 1. PC Configuration

1. Install PowerPanel Business Edition Client on every PC that will be part of the
shut down process. (Follow the instructions in the PowerPanel Business Edition
Client user manual).

2. Configure the settings in PowerPanel Business Edition Client. See the
PowerPanel Business Edition Client User Manual for additional help.

Step 2. PDU Configuration

1. Verify that the IP address of all PCs that will be part of the shut down process
are included in the Client List of web interface (For additional information,
please refer to the user’s manual in the PDU Software Installation CD).

Step 3. Notification
Notifying the PCs of potential outlet shutdown can be accomplished using the
following methods:

• Outlets Control Menu: Performing the task of turning off or rebooting outlets.

• Scheduling Menu: Setting the scheduler to perform the task of turning off or

rebooting outlets. The notification will occur prior to the scheduled date/time.

• Outlet Overload: In event of a PDU overload, notification will be sent prior to

the PDU shutting down.

Firmware Upgrade

By upgrading the Firmware, you can obtain new features and updates/
improvements to existing functionality. There are two files to update in order to
upgrade the firmware version:

* cpspdubfw_XXX.bin
* cpspdubdata_XXX.bin

Note that the XXX is not part of the file name but is where the version number in
the filename is given.
Use the following steps to upgrade the firmware.

1. Download the latest firmware from cpsww.com

2. Extract the file to “C:\”

3. Open a command prompt window and navigate to "C:\".

4. Login to the PDU with FTP command, type
* ftp
* ftp (after entering ftp mode, ftp> will display in the command prompt as
shown below instead of C:\ )
* To [current IP of the PDU] [port](for example: To 192.168.22.12 21 [21 is the
default ftp port for the PDU])
* Input USER NAME and PASSWORD (same as the administrator
account in Web interface default : cyber ; cyber)

5. Upload the cpspdubfw_XXX.bin, type
* ftp > bin
* ftp > put cpspdubfw_XXX.bin

6. Upgrade complete, type
* ftp > quit

7. The system will reboot after you type "quit". This reboot will take approx. 30 seconds.

8. Login to the FTP again
* ftp
* ftp> open
* To [current IP of the PDU] [port] (for example: To 192.168.22.12 21 [21 is the
default ftp port for the PDU])
* Input USER NAME and PASSWORD

9. Upload cpspdubdata_XXX.bin
* ftp > bin
* ftp > put cpspdubdata _XXX.bin

10. Upgrade complete , type
* ftp > quit

11. The system will reboot after you type “quit”

You can check to see if the firmware upgrade is successful by checking the
“Firmware version” on the [System->About] webpage.

Note: Please do not turn the PDU off when processing the Firmware upgrade.

20

For more information on CyberPower products, visit www.CPSww.com

Troubleshooting

Frequently Ask Questions (FAQ)

Q. What do I do if I’ve lost the Administrator username and/or password?
A. Resetting the PDU will set the username and password back to system default.

Please see the Device Reset section to reset the PDU.

Conformance Approvals

WARNING!! This equipment has been tested and found to comply with the limits
fora Class A Digital Device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Any special accessories needed for compliance must be specified in the instruction.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

Notice: (1) An unshielded-type power cord is required in order to meet FCC
emission limits and also to prevent interference to the nearby radio and television
reception. It is essential that only the supplied power cord by used. (2) Use only
shielded cables to connect I/O devices to this equipment.
Note: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

The Class A digital apparatus meets all requirements of the Canadian Interference­Causing Equipment Regulation.
Cet appareil numerique de la class A respecte toutes les exigencies du Reglement
sur le materiel brouilleur du Canada.

Problem Possible Cause Solution

PDU outlets do not
provide power to
connected equipment

1. Breaker tripped

2. Loose power cord

Reset Breaker, check if plug is
completely connected. If the
problem remains, contact
tech support.

Amperage displayed
on Metered Readout
exceeds the units
capability

1. Overload The load indicator shows red
when overload. Reduce the load
on the PDU until the overload
is gone. If the problem remains,
contact technical support.

Circuit breakers have
tripped

1. Sustained overload

2. Excessive ambient or

internal temperatures

3. Faulty breaker

Reset Breaker.
If the problem remains, contact
technical support.

21

For more information on CyberPower products, visit www.CPSww.com

Customer Service & Warranty

• Product Registration
Thank you for purchasing a CyberPower product. Prompt product registration
entitles coverage under the Limited Warranty, and also allows the opportunity to
be notified of product enhancements, upgrades, and other announcements.

Registration is quick and easy at www.cpsww.com/support/warranty-registration.html

• CyberPower International
Feel free to contact our Tech Support department with installation, troubleshooting, or
general product questions.

CyberPower Taiwan

Phone: [phone]
Email: [e-mail]
Web: www.cpsww.com.tw

CyberPower North America

Phone: [phone] Toll-free: [phone]
Email: [e-mail]
Web: www.CPSww.com
Add: 4241 12th Avenue E., Suite 400 Shakopee, MN 55379
Hours of Operation: Monday-Friday 8:00 AM-5:00 PM (CST)

CyberPower Europe

Email: [e-mail]
Web: www.cpsww.eu

• Limited Warranty

Read the following terms and conditions carefully before using the CyberPower
PDU series. By using the Product, you consent to be bound by and become a party
to the terms and conditions of this Limited Warranty. If you do not agree to the
terms and conditions of this Warranty, you should return the Product for a full
refund prior to using it.

Who Is Providing This Warranty?

CyberPower Systems (Taiwan), Inc. /CyberPower Systems (USA), Inc. /CyberPower
Europe ("CyberPower") provides this Limited Warranty.

What Does This Warranty Cover?

This warranty covers defects in materials and workmanship in the Product under
normal use and conditions.

What Is the Period of Coverage?

CyberPower provides a 2-Year warranty to the original purchaser who owns
the Product.

Who Is Covered?

This warranty only covers the original purchaser.
Coverage ends if you sell or otherwise transfer the Product.

How Do You Get Service?

1. You can use the contact information mentioned above for instructions.

2. When you contact CyberPower, identify the Product, the Purchase Date,
and the item(s) of Connected Equipment. Have information on all applicable
insurance or other resources of recovery/payment that are available to the
Initial Customer and Request a Claim Number.

3. You must provide a purchase receipt (or other proof of the original purchase)

and provide a description of the defect.

What Will We Do To Correct Problems?

CyberPower will inspect and examine the Product.
If the Product is defective in material or workmanship, CyberPower will repair or
replace it at CyberPower's expense, or, if CyberPower is unable to or decides not
to repair or replace the Product (if defective) within a reasonable time,
CyberPower will refund to you the full purchase price you paid for the Product
(purchase receipt showing price paid is required).
If it appears that our Product failed to protect any equipment plugged into it, we will
also send you forms for making your claim for the connected equipment. We will repair
or replace the equipment that was damaged because of the failure of our Product or
pay you the fair market value (NOT REPLACEMENT COST) of the equipment at of the
time of the damage. We will use Orion Blue Book, or another a third-party valuation
guide, or eBay, craigslist, or other source to establish that amount. Our liability is limited
to the amount, if any, stated in the Technical Specifications.

Who Pays for Shipping?

We pay when we send items to you; you pay when you send items to us.

What Are Some Things This Warranty Does Not Cover?

1. This Warranty does not cover any software that is damaged or needs to be replaced
due to the failure of the Product or any data that is lost as a result of the failure or
the restoration of data or records, or the reinstallation of software.

2. This Warranty does not cover or apply to: misuse, modification, operation or
storage outside environmental limits of the Product or the equipment
connected to it, nor for damage while in transit or in storage, nor if there has
been improper operation or maintenance, or use with items not designed or
intended for use with the Product, such as laser printers, appliances, aquariums,
medical or life support devices, etc.

22

For more information on CyberPower products, visit www.CPSww.com

Customer Service & Warranty

What Are The Limitations?

1. This Warranty does not apply unless the Product and the equipment that was
connected to it were connected to properly wired and grounded outlets
(including compliance with electrical and safety codes of the most current
electrical code), without the use of any adapters or other connectors.

2. The Product must have been plugged directly into the power source and the
equipment connected to the Product must be directly connected to the Product
and not "daisy-chained" together in serial fashion with any extension cords,
another Product or device similar to the Product, surge suppressor, or power
tap. Any such installation voids the Limited Warranty.

3. The Product and equipment connected to it must have been used properly in a
suitable and proper environment and in conformance with any license,
instruction manual, or warnings provided with the Product and the equipment
connected to it.

4. The Product must have been used at all times within the limitations on the
Product's VA capacity.

5. The sole and exclusive remedies of the Initial Customer are those
provided by this Warranty

Appendix A-Hyper Terminal

Hyper Terminal software can be used for basic PDU configuration. It utilizes a
text-based interface and menu system. Navigation through the interface is done
by typing the number of the menu option and pressing the Enter key. Note: The
session will timeout and logout after 3 minutes of inactivity. Menu options are
shown below:

[Main Menu]

1. Network Settings

2. System Configuration

3. Account Settings

4. Configure System to Default

5. Logout

[Network Setting]

Physical MAC Address: 00-0C-15-40-08-A9

1. System IP: 192.168.24.20

2. Subnet Mask: 255.255.255.0

3. Default Gateway: 192.168.24.254

4. DHCP: Enable

5. Http Port: 80

6. Http Access: Enable

[System Configuration]

1. Date (mm/dd/yyyy) : 11/11/2011

2. Time (hh:mm:ss): 17:17:25

3. Name:PDU20SW8FNET

4. Contact: Administrator

5. Location: Server Room

[Account Setting]

1. Administrator

2. Viewer(Web Only)

[Configure System to Default]

Sure to Configure System to Default

1. Yes

0. NO

23

For more information on CyberPower products, visit www.CPSww.com

Appendix B-Power Device Network Utility

• Overview

The CyberPower Power Device Network Utility is an easy-to-use interface which is
used for establishing IP addresses on CyberPower PDU devices.

• Installation

Step 1. Insert the CD labeled “PDU Software Installation CD” into the CD/DVD drive.
Step 2. Select Power Device Network Utility from the installation menu (Shown in
Figure 1.).

Step 3. Select Next in the software wizard.
Step 4. Choose an installation directory and user settings.
Select Next (Shown in Figure 2.).

Step 5. Select Next to comfirm the settings and install.
Step 6. Select Close to finalize the installation.

Figure 1. Installation Menu

Figure 2. Installation folder and settings

24

For more information on CyberPower products, visit www.CPSww.com

Appendix B-Power Device Network Utility

• Launch Program
To launch the Power Device Network Utility and get started, select Programs from
the Start menu in Windows and locate the new folder and icons for Power Device
Network Utility. Select Power Device Network Utility from the program folder
(Shown in Figure 3.).

• Getting Started
The Power Device Network Utility scans the network for devices with MAC
addresses that match CyberPower network hardware. Once found, the device(s)
can then be figured with a specific IP address, subnet mask, and gateway address.
This allows the device(s) to function properly on the network and interface with
CyberPower Management Console.
Step 1. Select the appropriate PDU device from the Equipment List (Shown in Figure 4.).

Note: If the PDU does not appear on the list, click the Refresh button to rescan the
network. If it still does not appear, ensure that the PDU is turned on and was
installed correctly.
Pressing Stop will cancel the scan/refresh process.

Note: If your computer has a software firewall installed, you may see a Windows
Security Alert message (Shown in Figure 5.).
In Windows XP SP2, the default firewall alert message is shown as Figure 5. You
need to allow the Power Device Network Utility access through the firewall.

Figure 3. Power Device Network Utility

Figure 4. Equipment List

Figure 5. Windows Security Alert

25

For more information on CyberPower products, visit www.CPSww.com

Appendix B-Power Device Network Utility

Step 2. Assign a valid IP Address to the PDU

Option 1: Assisted Setup (recommended)
With the appropriate device selected from the Equipment List, open the Network
Settings menu (Shown in Figure 6.). [Tools=>Device Setup]. In the Device Network
Setting Menu, enter a valid IP address, subnet mask, and gateway address to
setup the PDU device.

Note: The DHCP option is not available for all power devices.

Step 3. Authentication
Enter the user name and password of the PDU device at the Authentication menu
(Shown in Figure 7.).
Note: The default username is “cyber” and the default password is “cyber”.

• Advanced Settings

Timeout Settings
The Timeout Setting (Shown in Figure 8.). [Edit=>Timeout Settings] is used to
specify the wait time when scanning for network PDU devices. When there are
many devices on the local network, it may take extended periods of time to locate
all the devices. The timeout function is used to limit the search time.
The default setting is 3 seconds. Valid values are 3 to 60 seconds.

Figure 6. Network Setting Menu (Device Setup)

Figure 7. Authentication screen

Figure 8. Timeout Setting

K01-0000272-00

CyberPower Systems, Inc.

www.CPSww.com