CyberPower OLS6000ECXL, OLS10000EC, OLS6000EC, OLS10000ECXL User Manual

User’s Manual

CyberPower Systems Inc.
www.cyberpower.com

OLS6000EC(XL)

OLS10000EC(XL)

K01-C000550-00

CONTENT：

1. Safety .................................................................................................................1

1.1. Installation ..................................................................................................1

1.2. Operation ....................................................................................................1

1.3. Maintenance,Servicing and Faults ..............................................................2

1.4. Transport ....................................................................................................3

1.5. Storage .......................................................................................................3

1.6. Standards ...................................................................................................3

2. Description of Commonly Used Symbols .......................................................4

3. Introduction .......................................................................................................4

3.1. Feature .......................................................................................................5

3.2. Electrical Specifications ..............................................................................6

3.3. Operating Environment ...............................................................................7

3.4. Dimensions and Weights ............................................................................7

4. Installation .........................................................................................................8

4.1. Power Wires Installation .............................................................................8

4.2. External Battery Pack Installation ............................................................. 12

4.3. EPO Connection ....................................................................................... 12

5. Operation ......................................................................................................... 13

5.1. Panel Display and Control ........................................................................ 13

5.2. Turn On/Off UPS ...................................................................................... 16

5.3. Operating Modes ...................................................................................... 17

6. Trouble Shooting ............................................................................................ 18

6.1. Warning Indication .................................................................................... 18

6.2. Fault Indication ......................................................................................... 20

6.3. Others ....................................................................................................... 22

7. Battery Maintenance ....................................................................................... 23

8. Communication Port ....................................................................................... 23

8.1. USBPort .................................................................................................... 23

8.2. RS232 Interface ........................................................................................ 23

8.3. Intelligent Slot ........................................................................................... 23

This manual contains important instructions. Please read and follow all
instructions carefully during installation and operation of the unit. Read this
manual thoroughly before attempting to unpack, install, or operate the UPS.

1. Safety

1.1. Installation

 This is permanently connected equipment, and it must be installed by qualified

maintenance personnel.

 Condensation may occur if the UPS is moved directly from a cold to a warm

environment. The UPS must be absolutely dry before being installed. Please
allow an acclimatization time of at least two hours.

 Do not install the UPS near water or in damp environment.
 Do notinstall the UPS where it would be exposed to direct sunlight or near heat.
 Do not connect appliances or items of equipment which would overload the

UPS (e.g. laser printers, etc.) to the UPS output.

 Do not block ventilation openings in the UPS’s housing. Ensure allow at least

0.5m of space on front and rear of the UPS.

 Connect UPS with the earth reliably before connecting to the building wiring

terminal, and external battery source must also be earthed.

 An integral single emergency switching device which prevents further supply to

the load by the UPS in any mode of operation should be provided in the building
wiring installation.

 An appropriate disconnect device as short-circuit backup protection should be

provided in the building wiring installation.

 The equipment is powered by two sources: the mains source, the internal

battery or the external battery source.

 With the installation of the equipment, the sum of the leakage current of the UPS

and the connected load does not exceed 5% of rated value of input current.

1.2. Operation

 Do not disconnect the main cable on the UPS or the building wiring terminals

during operation since this would remove the protective earth from the UPS and
all connected loads.

 The UPS output terminal block may still be electrically lived from internal current

1

source (batteries) even if the UPS is not connected to the building wiring
terminal.

 In order to fully disconnect the UPS, turn the input breaker in the

"OFF"positionfirst, and then disconnect the mains lead.

 Indiscriminate operation of switches may cause output loss or damage to

equipment. Refer to instruction before conducting any control.

 While the UPS work as a parallel system, the external parallel cable should be

reinforced insulation.

 Ensure that no liquid or other foreign objects can enter the UPS.

1.3. Maintenance,Servicing and Faults

 Do not remove the enclosure since the UPS operates with hazardous voltages.

It must be serviced only by qualified maintenance personnel.

 Caution!Risk of electric shock. Even the UPS is disconnected from the mains

power supply (building wiring terminal), components inside the UPS are still
connected to the battery which are potentially dangerous.

 Before carrying out any kind of serviceor maintenance, isolate UPS and

disconnect the batteries. Verify that no current and no hazardous voltage exists
in the capacitor or BUS capacitor.

 Batteries must be replaced only by qualified personnel.
 Batteries have a high short-circuit current and pose a risk of shock. Take all

precautionary measures specified below and any other necessary measures
when working with batteries:

─ remove all jewelry, wristwatches, rings and other metal objects
─ use only tools with insulated grips and handles.

 When changing batteries, replace with the same quantity and the same type of

batteries.

 Do not attempt to dispose of batteries by burning them. It could cause

explosion.

 The UPS may be connected to external battery package. Proper disposal of

batteries is required. Refer to your local codes for disposal requirements.

 Do not open or destroy batteries. Effluent electrolyte can cause injury to the skin

and eyes. It may be toxic.

 In order to avoid fire hazards when replacing the fuse, only use the same type

and the same spec of fuse.

2

* Safety

IEC/EN 62040-1

* EMI

Conducted Emission................................:IEC/EN 62040-2

Category C3

Radiated Emission...................................:IEC/EN 62040-2

Category C3

*EMS

ESD.........................................................:IEC/EN 61000-4-2

Level 3

RS............................................................:IEC/EN 61000-4-3

Level 3

EFT..........................................................:IEC/EN 61000-4-4

Level 4

SURGE....................................................:IEC/EN 61000-4-5

Level 4

Low Frequency Signals............................:IEC/EN 61000-2-2

Warning: This is a product for commercial and industrial applicationin the
second environment-installation restrictions or additionalmeasures may be
neededto prevent disturbances.

1.4. Transport

Please transport the UPS only in the original packaging to protect against shock
and impact.

1.5. Storage

The UPS must be placed in the room where is ventilated and dry.

1.6. Standards

3

Symbol

Explanation

Alert you to pay special attention

Alternating current source(AC)

Turn on or turn off the UPS

Recycle

Caution of high voltage

Direct current source(DC)

Protective ground

Do not dispose with ordinary trash

2. Descriptionof Commonly Used Symbols

Some or all of the following symbols may be used in this manual. It is advisable to
familiarize yourself with them and understand their meaning:

3. Introduction

This On-Line series is an uninterruptible power supply
incorporatingdouble-converter technology. It provides perfect protection
specificallyfor computer equipment, communication servers, and data centers.
The double-converter principle eliminates all mains power disturbances. A rectifier
converts the alternating current from the mains power to direct current. On the
basis of this DC voltage, the invertergenerates an AC sinusoidal voltage, which
constantly supplies theloads. In the event of power failure, the maintenance-free
batteriespower the inverter.
This manual covers the UPS listed as follows. Please confirm whetherit is the
model you intend to purchase by performing a visual inspectionof the Model No. on
the rear panel of the UPS.

4

Model No.

Type

Model No.

Type

OLS6000EC

Standard

OLS6000ECXL

Extended

backup time

OLS10000EC

OLS10000ECXL

"XL"Model: Extended backup time.

3.1. Feature

This series UPS provides theoutstanding reliability, and most cost-performance
ratio in the industrial.Thebenefitsinclude:

 True online double-conversion technology with high powerdensity, frequency

 Selectable ECO mode, operating with 96% efficiency.
 Operate with high input power factor (more than 0.99) and high efficiency(more

5

OLS6000EC/OLS10000EC OLS6000ECXL/OLS10000ECXL

Fig.3-1 UPS rear view

independenceand generator compatibility.

than 92%);it could save power and wiring expense.

Input

Model NO.

OLS6000EC(XL)

OLS10000EC(XL)

Phase

Single

Voltage Range

110~276Vac(Depends on load level)

Frequency Range

(45~55)/(54~66)Hz

Rated Current

31(36)A

50(55)A

Power Factor

≥0.99@full load

Battery

Rated Voltage

192Vdc

Rated Current

31A

51A

Output

Power Rating

6kVA/4.8kW

10kVA/8kW

Voltage*

208/220/230/240Vac

Frequency

Synchronized50/60×(1±10%)Hz @Line mode

50/60×(1±0.1%)Hz @Battery mode

Wave Form

sine

Load Type

PF 0.5~1, lagging

THDV

≤ 2% @ full linear load

≤ 5% @ full nonlinear load

 With perfect output sinewaveform;output power factor is 0.8.It is suitablefor

almost all critical equipment.

 Outstanding adaptability to the worst mains input condition.Extra wide input

voltage, frequency range, and sine waveform could avoiddissipating limited
battery energy.

3.2. Electrical Specifications

6