CyberPower DX400E-DE, DX600E-DE, DX800E-DE User Manual



K01-0000114-00

DX400E-DE / DX600E-DE / DX800E-DE

User’s Manual



2

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important instructions that should be followed during installation and
maintenance of the UPS and batteries. Please read and follow all instructions carefully during
installation and operation of the unit. Read this manual thoroughly before attempting to
unpack, install, or operate.
CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit
breaker protection. DO NOT plug the UPS into an outlet that is not grounded. If you need to
de-energize this equipment, turn off and unplug the UPS.
CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower
Systems does not sell products for life support or medical applications. DO NOT use in any
circumstance that would affect the operation or safety of any life support equipment, with any
medical applications, or patient care.
CAUTION! The battery can energize hazardous live parts inside even when the AC input
power is disconnected.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity
controlled indoor area, free of conductive contaminants. (Please see specifications for
acceptable temperature and humidity range).
CAUTION! To reduce the risk of electric shock, do not remove the cover. There are no user serviceable
parts inside.
CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source
before installing a computer component.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not
use with or near aquariums. Condensation from the aquarium can come in contact with metal
electrical contacts and cause the machine to short out.
CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser printers
are too large for a UPS.

INSTALLING YOUR UPS SYSTEM

UNPACKING

The box should contain the following:
(1) UPS Unit x 1; (2) USB Cable x 1; (3) User Manual x 1; (4) Management software Disk x 1

OVERVIEW

The DX400E-DE/DX600E-DE/DX800E-DE features 405 Joules of surge protection, and provides
battery backup during power outages. The DX400E-DE/DX600E-DE/DX800E-DE ensures consistent
power to your computer system and its included software will automatically save your open files and
shutdown your computer system during a utility power loss.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR
EQUIPMENT

1.Make sure that the total Volt-Amp (VA) requirements of your computer, monitor, and peripheral
equipment does not exceed 400VA/ 600VA/800VA.

2.Ensure that the equipment plugged into the battery power-supplied/surge outlets does not exceed the
UPS unit's rated capacity (400VA/240W for DX400E-DE, 600VA/360W for DX600E-DE,
800VA/480W for DX800E-DE). If the rated unit capacities are exceeded, an overload condition may
occur and cause the UPS unit to shut down or the circuit breaker to trip.

3

BASIC OPERATION

DESCRIPTION

①

Power On/Off Switch

Press the power switch to turn the UPS ON or OFF.

②

LED Indicators

Three LED indicators include Using AC, Using Battery, and Fault. Refer to “Definitions for

Illuminated LED Indicators” section for details.

③

Battery Capacity Indicators

The indicators show the battery capacity remains during battery mode. Refer to “Definitions for
Illuminated LED Indicators” section for details.

④

AC outlet

The UPS provides 3 outlets for connected equipment to insure temporary uninterrupted operation
during a power failure and against surges and spikes.

⑤

USB Port to PC

This port allows connection and communication from the USB port on the computer to the UPS unit.
The UPS communicates its status to the PowerPanel

®

Personal Edition software.

⑥

Input Circuit Breaker

The Circuit Breaker provides optimal overload protection.

