Page 1
BPSE36V45A (72V45A)RT2U
User’s Manual
K01- C000049-01
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important instructions. Please read and follow all instructions carefully
during installation and operation of the unit. Read this manual thoroughly before attempting to
unpack, install, or operate the Battery modules.
CAUTION! The UPS unit must be connected to a grounded AC power outlet with fuse or circuit
breaker protection. The Battery modules grounded are through the UPS.
CAUTION! The battery can power hazardous components inside the unit, even when the AC
input power is disconnected.
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity
controlled indoor area, free of conductive contaminants. (Please see specifications for
acceptable temperature and humidity range).
CAUTION! (No User Serviceable Parts): Risk of electric shock, do not remove cover. No user
serviceable parts inside. Refer servicing to qualified service personnel.
CAUTION! (Non-Isolated Battery Supply): Risk of electric shock, battery circuit is not
isolated from AC power source; hazardous voltage may exist between battery terminals and
ground. Test before touching.
CAUTION! Wiring must be done by qualified personnel.
CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not
use with or near aquariums. Condens ation from the aquarium can come in contact with metal
electrical contacts and cause the machine to short out.
CAUTION! Do not dispose of batteries in fire as the battery may explode.
CAUTION! Do not open or mutilate the battery, released electrolyte is harmful to the skin and
eyes.
CAUTION! A battery can present a risk of electric shock and high short circuit current. The
following precaution should be observed when working on batteries.
1. Remove watches, rings or other metal objects.
2. Use tools with insulated handles.
CAUTION! Make sure everything is turned off and disconnected completely before conducting
any maintenance, repairs or shipment.
CAUTION! Connect the Protection Earth (PE) safety conductor before any other cables are
connected.
DO NOT INSTALL THE UNIT WHERE IT WOULD BE EXPOSED TO DIRECT SUNLIGHT OR
NEAR A STRONG HEAT SOURCE!
SERVICING OF BATTERIES SHOULD BE PERFORMED OR SUPERVISED BY PERSONNEL
KNOWLEDGE OF BATTERIES AND THE REQUIRED PRECAUTIONS. KEEP
UNAUTHORIZED PERSONNEL AWAY FROM BATTERIES!
UNPACKING
UNPACKING
The box should contain the following items:
Batteries Module
User’s manual
Battery Cable
rackmount ears ( 2 PCS )
Rackmount rails ( L & R )
Flat head screws: M4X8L (8)
Pan head screws: M5X12L (12)
Plastic washers (8)
Screw hole dust covers (8)
Page 2
BASIC OPERATION
FRONT/REAR PANEL DESCRIPTION
BPSE36V45ART2U, BPSE72V45ART2U
1. Input Connector
Use this input connector to daisy chain the next Battery module. Remove the connector cover for
access.
2. On-board Replaceable Fuse Cover
Replaceable fuse is accessible from the rear panel. It must be done by qualified personnel.
3. Battery Output Connector
Use this output Connector to connect the Battery module to the Power module or to the next
Battery module.
HARDWARE INSTALLATION
These batteries modules can be mounted in a rackmount or vertical tower orientation. This
versatility is especially important to growing organizations with changing needs that value having
the option to position a batteries module on a floor or in a rackmount system. Please follow the
instructions below for the respective mounting methods.
SAFETY PRECAUTIONS
CAUTION! To prevent the risk of fire or electric shock, only use the supplied hardware to attach
the mounting brackets.
RACKMOUNT INSTALLATION
Step 1: Rackmount ears installation
1) Attach the two rackmount ears to the batteries module using the provided screws
M4X8L*8pcs.
Step 2: Rackmount rail Installation
1) The rails adjust to mount in 48-cm (19-inc h) panel racks from 52 to 91.5cm (20.5 to 36
inches) deep. Select the proper holes in the rack for positioning the batteries module in the
rack. It takes up position 1 through position 6.
Page 3
2) Attach the rackmount rail to your rack with two M5X12L screws and two plastic washers at
the front of the rack. (Located in position 1 & position 6) Do not tighten the screws. Adjust
the rail size on the rail assembly of your rack. Secure the rail to the rear of the rack with two
M5X12L screws and two plastic washers. Tighten all screws at the front and rear of the rail.
Once completed, perform the same steps for assembling the other rackmount rail.
Step 3: Install the batteries module on the rack
Place the batteries module on a flat stable surface with the front of the unit facing toward
you. Secure the batteries module to your rack with four M5X12L screws at the front of the
rack. (Located in position 2 & position 5)
Page 4
VERTICAL/TOWER INSTALLATION
Step 1: Attach the base stands
Tighten the screws (M5X12*8pcs) of the base stands (rackmount ears) onto the bottom of the
batteries module.
Step 2: Attach dust covers
Insert dust cover into the rackmount ear screw holes that are not being used.
Battery Installation and replacement
Step 1: Remove the front panel. Remove the retaining screws from the battery bracket and then
remove the cover itself. undraw the connectors.
Step 2: Pull the battery tray out slowly. Put the new battery tray back into the compartment after
that.
Page 5
Step 3: Fasten the battery bracket and then insert the connectors. Place the connectors in the
bracket.
.
Step 4: Tighten the screws of the battery bracket and front panel .
Step 5: Repeat from step1 to step4 to replace the other side batteries pack.
CONNECTION : POWER MODULE(UPS) WITH BATTERY MODULE
CONNECTION 1 : POWER MODULE(UPS) WITH ONE BATTERIES MODULE
Step 1: Loosen the two screws to remove the battery cable retention bracket of the Power
module and Batteries module.
Step 2: Use the battery cable to connect the Batteries module to the Power module.
Step 3: Rotate the battery cable retention bracket and tighten the two screws to fix battery cable
on the Power module and Batteries module.
CONNECTION 2 : POWER MODULE(UPS) WITH MULTIPLE BATTERY MODULES
Step 1: Connect the 1
st
Batteries module to the Power module using battery cable. (Refer to
above steps of connection #1)
Step 2: Loosen the two screws to remove the battery cable retention bracket of the 1st batteries
module and 2nd Battery module.
Step 3: Use the battery cable to connect the 2nd Batteries module to the 1st Batteries module.
Step 4: Rotate the battery cable retention bracket and tighten the two screws to fix battery cable
on 1st batteries module and 2nd Batteries module.
Page 6
TECHNICAL SPECIFICATIONS
Model BPSE36V45ART2U BPSE72V45ART2U
Battery
Sealed Maintenance Free
Lead Acid Battery
12V / 7Ah x3pcs x2sets 12V / 7Ah x6pcs x2sets
Rated Battery Voltage 36Vdc 72Vdc
Overload Protection Fuse
Physical
Dimensions (H x W x D)
3.46 x 17.24x15.75 in.
88×438×400 mm
3.46 x 17.24x22.83in.
88×438×580 mm
Weight (kg) 24.2 34.7
Environment
Operating Temperature 0C to 40C
Relative Humidity 0 to 90% (Non-condensing)
For more information, visit www.cpsww.com
All rights reserved. Reproduction without permission is prohibited.
Loading...